8120 M Tellabs Node Operating Manual 1q2w16

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 22030_12 07.01.2013

Document Information

Revision History Document No.

Date

Description of Changes

22030_12

07.01.2013

The Tellabs 8120 mini node has been discontinued. A discontinuation note has been added in ch. 1.

22030_11

09.03.2009

Erroneous V35-M discontinuation note removed throughout the document.

22030_10

29.08.2008

Layout and cross reference changes due to format conversion throughout the document.

22030_09

02.11.2007

Safety notes related to grounding updated in chapters 4.5 and 6.11. Outdated data removed from the foreword. Figures 2, 24, 25 and 40 updated. The list of numbered items referring to the mechanical construction updated in chapter 4.8. Disassembling instructions updated in chapter 4.8.1. EMC standard updated in chapter 6.12.

© 2013 Tellabs. All rights reserved. This Tellabs manual is owned by Tellabs or its licensors and protected by U.S. and international copyright laws, conventions and treaties. Your right to use this manual is subject to limitations and restrictions imposed by applicable licenses and copyright laws. Unauthorized reproduction, modification, distribution, display or other use of this manual may result in criminal and civil penalties. The following trademarks and service marks are owned by Tellabs Operations, Inc. or its s in the United States and/or other countries: TELLABS ®, TELLABS ® logo, TELLABS and T symbol ®, and T symbol ®. Any other company or product names may be trademarks of their respective companies. The specifications and information regarding the products in this manual are subject to change without notice. All statements, information, and recommendations in this manual are believed to be accurate but are presented without warranty of any kind, express or implied. s must take full responsibility for their application of any products. Adobe ® Reader ® are ed trademarks of Adobe Systems Incorporated in the United States and/or other countries.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 2

22030_12 © 2013 Tellabs.

Document Information

and Abbreviations Term

Explanation

ADPCM

Adaptive Differential Pulse Code Modulation

AIS

Alarm Indication Signal

CAS

Channel Associated Signalling

CRC

Cyclic Redundancy Check

DMA

Deferred Maintenance Alarm

FAS

Frame Alignment Signal

FrFEA

Frame Far-end Alarm

HDLC

High Level Data Link Control

IF

Interface

MEI

Maintenance Event Information

MFrFEA

Multiframe Far-end Alarm

PMA

Prompt Maintenance Alarm

RAI

Remote Alarm Indication

TS

Time Slot

VF

Voice Frequency

Compliance Statement Hereby, Tellabs Oy declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 3

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 4

22030_12 © 2013 Tellabs.

Table of Contents

Table of Contents

About This Manual .............................................................................................................. 9 Objectives......................................................................................................................................................................... 9 Audience........................................................................................................................................................................... 9 Discontinued Products...................................................................................................................................................... 9 Document Conventions .................................................................................................................................................... 9 Documentation ............................................................................................................................................... 10

1

Introduction ................................................................................................................. 11 1.1

2

Tellabs 8120 Mini Node M as Tellabs 8100 Network Element.................................. 13 2.1 2.2 2.3

2.4

2.5

3

Construction..........................................................................................................................................................11

General................................................................................................................................................................. 13 Framed Interfaces IF1 and IF2 ............................................................................................................................ 14 Access Ports ................................................................................................................................................ 16 2.3.1 Unframed Interfaces ............................................................................................................................ 16 2.3.2 Framed Interface as Access Port................................................................................................. 17 2.3.3 Rules for Mixing Different Interface Types ........................................................................................ 17 Applications......................................................................................................................................................... 17 2.4.1 Framed Interfaces ................................................................................................................................ 17 2.4.2 Unframed Interfaces ............................................................................................................................ 20 Network Synchronization .................................................................................................................................... 23

Operation ..................................................................................................................... 25 3.1 3.2

3.3 3.4 3.5

3.6

22030_12 © 2013 Tellabs.

General................................................................................................................................................................. 25 G.704 Framed Interfaces IF1 and IF2 ................................................................................................................. 26 3.2.1 Frame and Multiframe Structure ......................................................................................................... 27 3.2.2 Buffers ................................................................................................................................................ 28 3.2.3 Split Trunk Lines ................................................................................................................................. 30 3.2.4 1+1 Protection ..................................................................................................................................... 30 Operation of Framed Interfaces ........................................................................................................................... 31 Unit Controller..................................................................................................................................................... 34 Cross-Connect Block........................................................................................................................................... 35 3.5.1 Cross-Connection ................................................................................................................................ 35 3.5.2 Master Clock Synchronization ............................................................................................................ 37 Operation of Unframed Channel Interfaces IF3-IF6 ........................................................................................... 38

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 5

Table of Contents

3.7

4

3.6.1 Data Formatting Functions .................................................................................................................. 39 3.6.2 Data Interfaces..................................................................................................................................... 43 3.6.3 Timing Modes...................................................................................................................................... 43 3.6.4 Rate Adaptation and Mapping............................................................................................................. 46 3.6.5 Cross-Connection of Unframed Interfaces .......................................................................................... 48 Test Resources ..................................................................................................................................................... 49 3.7.1 Equipment Test .................................................................................................................................... 49 3.7.2 Test of Framed Interfaces .................................................................................................................... 50 3.7.3 Tests of Unframed Interfaces............................................................................................................... 53

Installation ................................................................................................................... 56 4.1 4.2 4.3 4.4

Front Indicators and Controls .................................................................................................................... 56 Back Connections ...................................................................................................................................... 56 Mains Connection................................................................................................................................................ 58 Operating Environment ....................................................................................................................................... 58 4.4.1 DC Power Supply Cabling .................................................................................................................. 59 4.4.2 SC, Local Service Computer Connector.............................................................................................. 60 4.4.3 SYNC Connector................................................................................................................................. 60 4.5 Configuration of Tellabs 8120 Mini Node M ...................................................................................................... 60 4.5.1 NMS Control ....................................................................................................................................... 62 4.5.2 Local Control....................................................................................................................................... 62 4.6 Menus of Tellabs 8120 Mini Node M ................................................................................................................. 63 4.6.1 Security Menu...................................................................................................................................... 68 4.6.2 Faults Menu ......................................................................................................................................... 71 4.6.3 Parameters Menu ................................................................................................................................. 72 4.6.4 Interface Parameters Menu.................................................................................................................. 75 4.6.5 Cross-Connection Menu ...................................................................................................................... 80 4.6.6 Copy Settings Menu ............................................................................................................................ 86 4.6.7 Entering Security Menu of Tellabs 8120 Mini Node M ...................................................................... 87 4.7 Recommended Settings of Framed Interfaces ..................................................................................................... 87 4.7.1 Framed Interface Used as 2048 kbit/s Trunk....................................................................................... 87 4.7.2 Framed Interface Used as 2048 kbit/s Access Point ................................................................... 88 4.7.3 Framed Interface Used as 8448 kbit/s Trunk....................................................................................... 89 4.7.4 BTE-384-M Settings............................................................................................................................ 90 4.7.5 BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M Settings ......................................... 91 4.7.6 Cross-Connection Example ................................................................................................................. 93 4.7.7 Binary-to-Hexadecimal Conversion Table .......................................................................................... 93 4.8 Service Operations and Modifications................................................................................................................. 94 4.8.1 Instructions on Disassembling Tellabs 8120 Mini Node M ................................................................ 96 4.9 Unit List of Tellabs 8120 Mini Node M .............................................................................................................. 97 4.9.1 Common Units..................................................................................................................................... 97 4.9.2 Main Interface Modules....................................................................................................................... 98 4.9.3 V Series Interface Modules ................................................................................................................. 99 4.10 Connectors and Strappings of Framed Interfaces.............................................................................................. 100 4.10.1 G703-75-M and G703-120-M, G.703 2 Mbit/s................................................................................. 100 4.10.2 LTE-M Line Terminal 1 or 2 Mbit/s.................................................................................................. 102 4.10.3 G703-8M-M, 8 Mbit/s ....................................................................................................................... 103 4.10.4 OTE-LED-M, Optical LED, 2 or 8 Mbit/s ........................................................................................ 103 4.10.5 BTE-384-M, BTE-1088-M, BTE-2048-M, BTE-2048-2W-M and BTE-4096-M, 384 kbit/s…4224 kbit/s .................................................................................................................................................. 104 4.10.6 BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M, 320…2304 kbit/s ....................... 106 Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 6

22030_12 © 2013 Tellabs.

Table of Contents

4.10.7 V35-G704-SM, V.35 n x 64 kbit/s…2 Mbit/s ................................................................................... 107 4.10.8 X21-G704-SM, n x 64 kbit/s…2Mbit/s............................................................................................. 108 4.11 Connectors and Strappings of Unframed Interfaces.......................................................................................... 109 4.11.1 V35-M, V.35 48, 56, n x 64 kbit/s Interfaces, 2 pcs .......................................................................... 109 4.11.2 V36-M, V.36 48, 56, n x 64 kbit/s Interfaces, 2 pcs ...........................................................................110 4.11.3 V24-DCE-M, V.24/V.28 if/DCE, 0.6…64 kbit/s, 2 pcs .....................................................................112 4.11.4 V24-DTE-M, V.24/V.28 if/DTE, 0.6…64 kbit/s, 2 pcs ......................................................................113 4.11.5 X21-M, X.21 1.2…n x 64 kbit/s Interface, 2 pcs ...............................................................................114 4.11.6 G703-64-M, G.703 64 kbit/s Co/Contradirectional Interface, 2 pcs ..................................................115 4.11.7 V35/V24-M, V.24/V.28 if/DCE, 0.6…64 kbit/s; V.35-IEC if, n x 64 kbit/s.......................................116 4.11.8 HSSI-M, TIA/EIA 612, 0.6…8448 kbit/s ..........................................................................................117 4.11.9 Mini LAN Module, 10Base-T, 64…2048 kbit/s.................................................................................119 4.12 Software Update ................................................................................................................................................ 120 4.12.1 ing Tellabs 8120 Mini Node M Software ......................................................................... 120 4.12.2 Replacing EPROMs........................................................................................................................... 121

5

Faults and Actions .................................................................................................... 123 5.1 5.2

5.3

6

Terminology....................................................................................................................................................... 123 Common Faults and Actions ............................................................................................................................. 124 5.2.1 Common Logic Faults (Block 0) ....................................................................................................... 124 5.2.2 Master Clock Faults (Block 0)........................................................................................................... 125 5.2.3 Cross-Connect Block Faults (Block 0).............................................................................................. 125 5.2.4 Faults of Framed IF Tx Signal (Block 1, 2) ..................................................................................... 126 5.2.5 Faults of Framed IF Rx Signal (Block 1, 2) ...................................................................................... 127 5.2.6 1+1 Protection Switch Fault Messages (Block 0) ............................................................................. 130 5.2.7 Miscellaneous Faults of Framed Interfaces (Block 1, 2)................................................................... 130 5.2.8 Fault and Service Status (PMA, DMA, MEI, S) in 1+1 Mode of Framed Interfaces ....................... 130 5.2.9 Fault Conditions of Framed Interfaces .............................................................................................. 131 Faults and Actions of Unframed Interfaces...................................................................................................... 132 5.3.1 General IF Faults of Unframed Interfaces ......................................................................................... 132 5.3.2 IF Signal Faults of Unframed Interfaces ........................................................................................... 133 5.3.3 Net Side Signal Faults of Unframed Interfaces ................................................................................. 133 5.3.4 Test Loop Activation of Unframed Interfaces ................................................................................... 134 5.3.5 Performance Conditions of Unframed Interfaces.............................................................................. 134 5.3.6 Common Faults of Unframed Interfaces ........................................................................................... 135 5.3.7 Reference Points of Unframed Interfaces.......................................................................................... 135

Technical Specifications of Tellabs 8120 Mini Node M .......................................... 136 6.1 6.2 6.3 6.4

6.5

22030_12 © 2013 Tellabs.

Relevant Recommendations .............................................................................................................................. 136 Cross-Connect ................................................................................................................................................... 137 Timing................................................................................................................................................................ 138 G.704 Framed Interface..................................................................................................................................... 138 6.4.1 Frame and Multiframe Buffer............................................................................................................ 138 6.4.2 8448 kbit/s Interface (CCITT G.704) ................................................................................................ 139 6.4.3 2048 kbit/s Interface (CCITT G.704/706)......................................................................................... 140 6.4.4 N x 64 kbit/s Interface with G.704 Type Frame ................................................................................ 141 Unframed Data Interfaces.................................................................................................................................. 142 6.5.1 V.24/V.28,V.35,V.36/V.11; 1.2…19.2 kbit/s, 48, 56, n x 64 kbit/s .................................................... 142

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 7

Table of Contents

6.5.2 X.21 1.2…19.2 kbit/s, 48, 56, n x 64 kbit/s....................................................................................... 143 6.5.3 Transparent 2 Mbit/s, n x 64 kbit/s.................................................................................................... 143 6.6 Data Interface Modules ..................................................................................................................................... 143 6.6.1 8448 kbit/s, G.703 Interface (G703-8M-M Module) ........................................................................ 143 6.6.2 2048 kbit/s, G.703 Interface (G703-75-M) ....................................................................................... 144 6.6.3 2048 kbit/s, G.703 Interface (G703-120-M) ..................................................................................... 144 6.6.4 2048 kbit/s and 1088 kbit/s Line Terminal Interface (LTE-M Module)............................................ 144 6.6.5 Optical Line Interface 2048 kbit/s / 8448 kbit/s (OTE-LED-M Module) ......................................... 145 6.6.6 Baseband Line Interface 64…384 kbit/s (BTE-384-M Module) ...................................................... 145 6.6.7 Baseband Line Interfaces 320...4224 kbit/s (BTE-1088-M, BTE-2048-M, BTE-2048-2W-M, BTE-4096-M, BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M Modules) ............. 146 6.7 Service Computer (SC) Interface ...................................................................................................................... 146 6.8 Power Supply..................................................................................................................................................... 147 6.8.1 Power Consumptions of Tellabs 8120 Mini Node M Units and Modules......................................... 147 6.9 Mechanics.......................................................................................................................................................... 148 6.10 Environmental Conditions................................................................................................................................. 148 6.10.1 Climatic/Mechanical Compatibility .................................................................................................. 148 6.11 Safety Compatibility.......................................................................................................................................... 149 6.12 Electromagnetic Compatibility.......................................................................................................................... 149

Appendix 1: Frame Structures ...................................................................................... 150 Frame Structures at Bit Rates 48…2048 Kbit/s ........................................................................................................... 150 Frame Structures at Bit Rates below 48 Kbit/s ............................................................................................................ 157

Appendix 2: G.704 Frame Structures............................................................................ 162 8448 kbit/s Frame Structure ......................................................................................................................................... 162 2048 kbit/s Frame Structure ......................................................................................................................................... 163 N x 64 kbit/s Frame Structure ...................................................................................................................................... 164 Multiframe Structure in Signalling Time Slot.............................................................................................................. 166 CRC Multiframe Structure in TS0 for 2 Mbit/s and n x 64 kbit/s Frames................................................................... 167

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 8

22030_12 © 2013 Tellabs.

About This Manual

About This Manual This section discusses the objectives and intended audience of this manual, Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual and consists of the following sections: • Objectives • Audience • Discontinued Products • Document Conventions • Documentation

Objectives The goal is to describe the network element features of Tellabs 8120 mini node M and its installation.

Audience This manual is intended for system specialists and personnel involved in network planning.

Discontinued Products Tellabs ® 8100 Managed Access System Discontinued Products list can be found in Tellabs Portal, www.portal.tellabs.com by navigating to Product Documentation > Managed Access > Tellabs 8100 Managed Access System (Includes all 81XX products) > Technical Documentation > Network Element Manuals > 8100 List of Discontinued Products.

Document Conventions This is a note symbol. It emphasizes or supplements information in the document.

This is a caution symbol. It indicates that damage to equipment is possible if the instructions are not followed.

This is a warning symbol. It indicates that bodily injury is possible if the instructions are not followed.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 9

About This Manual

Documentation Please us to suggest improvements or to report errors in our documentation: Email: [email protected] Fax: +358.9.4131.2430

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 10

22030_12 © 2013 Tellabs.

1 Introduction

1 Introduction The Tellabs 8120 mini node M has been discontinued.

This operating manual describes the version 6.1 or later of Tellabs ® 8120 mini node M (SBM 2048M). Tellabs ® 8120 mini node M (SBM 2048M) is a small cross-connect device, which can operate either as part of the Tellabs ® 8100 managed access system network connected to Tellabs ® 8000 network manager, or as a separate cross-connect device controlled and supervised locally. This piece of equipment can be furnished with up to two framed interfaces and up to two unframed interface modules (usually two interfaces per module). Tellabs 8120 mini node M can make connections between interfaces of any type. The transmission rates and physical features of the interfaces depend on the used interface modules. Different interface modules are available for different applications. The transmission rates of framed interfaces are 2048 kbit/s, 8448 kbit/s and n x 64 kbit/s, where n = 2…33. The frame structure of a framed interface is according to CCITT G.704. The modified G.704 frame is used at n x 64 kbit/s. The transmission rates of unframed interfaces can be 0.6…2048 kbit/s. The interfaces can, for example, be V.35, V.36, V.24 or X.21 depending on the used interface module. The configuration and control of Tellabs 8120 mini node M can be applied in different ways. As part of the Tellabs 8100 network, the control can be realised through Tellabs 8000 manager, where the control channel is connected to the device through a framed interface. On the front there is a connector for the service computer, which can manage the configuration and control with a interface with windows. The front of Tellabs 8120 mini node M is provided with an LCD display and keyboard (four buttons) which can handle the menu controlled interface control functions needed when using Tellabs 8120 mini node M.

1.1

Construction Tellabs 8120 mini node M is built into a compact metallic case. It is suitable for tabletop use. Under the metallic cover there are the following parts: • main unit • switching power supply unit (AC or DC) • channel board • two access interface modules • two framed interface modules On the front there are an LCD display with 2 x 24 characters, four pushbuttons, alarm LEDs for each channel and a connector for the service computer.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 11

1 Introduction

Fig. 1 Tellabs 8120 Mini Node M Front

On the back of Tellabs 8120 mini node M there are the interface connectors, a power cord, the synchronization connectors and a measurement point connector. The connector type depends on the module in use. The connectors for framed interfaces IF1 and IF2 are on the lower part of the back and the connectors for access ports on the upper part.

Fig. 2 Example of Tellabs 8120 Mini Node M Back Connectors

A framed interface module has one interface. The type for interfaces IF1 and IF2 can be selected irrespective of each other. An unframed interface module has typically two interfaces which are of the same type. The desired combination of modules can be selected for one piece of equipment according to the unit list. For further details and possible exceptions refer to 4.9 Unit List of Tellabs 8120 Mini Node M. For example in Fig. 2, the connectors for the framed interfaces IF1 and IF2 are on the bottom row of the back and the connectors for the access ports at the upper part of it. In this example the interface IF1 is G703-75-M, and the interface IF2 is OTE-LED-M. The interfaces IF3 and IF4 are of type V.36, and the interfaces IF5 and IF6 are of type V.35.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 12

22030_12 © 2013 Tellabs.

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element 2.1

General Tellabs 8120 mini node M is connected through the framed interfaces to another Tellabs 8120 mini node or a corresponding piece of equipment, a Tellabs 8100 node, the public transmission network or another transmission device with a G.703/G.704 interface. The interfaces with which Tellabs 8120 mini node M is connected to the Tellabs 8100 network or to another similar piece of equipment are called trunk interfaces in this manual. Tellabs 8120 mini node M can also be described as a digital multiplexer equipped with two trunk interfaces. Like an ordinary multiplexer, it can channel interfaces. The cross-connect function of the equipment is independent of the channel interfaces. This facilitates the flexible implementation of different channel interfaces.

Fig. 3 Architecture of Tellabs 8120 Mini Node M

The trunk interfaces are provided with the CCITT G.704/706 compliant frame structure. The system uses a synchronous time slot interleaved framing. A part of the frame is reserved for the internal information transfer of the system (frame alignment, CRC check, network management channel). For example, in the 2 Mbit/s G.704 frame this information is typically in time slot TS0. These time slots of the trunk lines are never used for transporting cross-connect channels (XB/XD channels). The access interfaces can be divided into two main categories: • unframed data • G.704 framed data A framed interface can also be a access interface. Cross-connections can be made in accordance with the following: 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 13

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

• framed/framed • framed/unframed • unframed/unframed When an interface is used for cross-connection, it is called a port. The mapping of the access ports to the trunks by the cross-connect are based on the following signals: • time slots: n x 64 kbit/s • time slot bits: n x 8 kbit/s The n x 8 kbit/s and n x 64 kbit/s groups mapped by the channel interfaces are called XB channels. The XB channel can also be a combination of 64 kbit/s and 8 kbit/s signals.

Fig. 4 XB and XD Channels

If the interfaces are equipped with signalling or control signals, they are either mapped to the XB channel or to the corresponding signalling bits (n x 500 bit/s) of the XB channel. In the latter case the signals are mapped into the G.704-compliant multiframe of the 2 or 8 Mbit/s trunk. The n x 500 bit/s signalling bits are called the XD channel of the interface. Unframed interfaces do not normally use the XD channel.

2.2

Framed Interfaces IF1 and IF2 In most cases the framed interfaces of Tellabs 8120 mini node M are used as trunk interfaces. The framed interfaces (IF1, IF2) provided by Tellabs 8120 mini node M are shown in the table below. (The modules are electrically, but not mechanically, identical with the modules in the GMH unit of the Tellabs 8100 system.)

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 14

22030_12 © 2013 Tellabs.

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

Framed Interface Modules Module Type

Electrical Interface

Bit Rate

XB/XD Capacity1

BTE-384-M2

2W/4W Biphase code

n= 2…6

n-2 TS for XB channels 1 TS for XD channels4

BTE-320-M2

2W 2B1Q code

n=5

n-1 TS for XB channels

BTE-576-M2

2W 2B1Q code

n=5, 9

n-1 TS for XB channels

BTE-10882W-M2

2W/4W 2B1Q code

n=5, 9, 16, 17

n-1 TS for XB channels

BTE-2048-M2

4W 2B1Q code

n=16, 17, 32, 33

n-2 TS for XB channels 1 TS for XD channels4

BTE-20482W-M2

2W 2B1Q code

n=16, 17, 32, 33

n-1 TS for XB channels

BTE-1088-M2

4W 2B1Q code

n=5, 9, 17

n-2 TS for XB channels 1 TS for XD channels4

BTE-2304-M2

2W/4W 2B1Q code

n= 16, 17, 32, 33, 34, 36

n-1 TS for XB channels

BTE-4096-M2

4W 2B1Q code

n= 16, 17, 82, 33, 64, 66

n-2 TS for XB channels 1 TS for XD channels4

LTE-M2, 3

LTE

1088 kbit/s

n-2 TS for XB channels 1 TS for XD channels4

2048 kbit/s

30 TS for XB channels 1 TS for XD channels4

V35-G704-SM2

V.36/V.11

n x 64 kbit/s n = 2…33

n-2 TS for XB channels 1 TS for XD channels4

X21-G704-SM2

V.11

n x 64 kbit/s n = 2…33

n-2 TS for XB channels 1 TS for XD channels4

OTE-LED-M

Optical LED

2048 kbit/s

30 TS for XB channels 1 TS for XD channels4

8448 kbit/s

120 TS for XB channels 4 TS for XD channels4 5 spare TS5

G703-75-M

G.703

2048 kbit/s

30 TS for XB channels 1 TS for XD channels4

G703-120-M

G.703

2048 kbit/s

30 TS for XB channels 1 TS for XD channels4

G703-8M-M2

G.703

8448 kbit/s

120 TS for XB channels 4 TS for XD channels4 5 spare TS5

1TS

= 64 kbit/s time slot. interface module has been discontinued. 3LTE = integrated line terminal. 4XD time slots can be turned off and used as XB time slots. 5One is used for HDLC. These five XB time slots do not have XD channels associated with them. 2The

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 15

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

2.3 2.3.1

Access Ports Unframed Interfaces Tellabs 8120 mini node M s two channel interface modules. Unframed Channel Interface Modules Module Type

Electrical Interface

Bit Rate

V35-M, V36-M6

V.35 or V.36/V.11

0.6…4224 kbit/s7

V24-DCE-M6 V24-DTE-M6

V.24/V.28

0.6…64 kbit/s

V35/V24-M6

V.24/V.28 V.35-IEC

0.6…64 kbit/s / 0.6…8192 kbit/s8

X21-M

X.21/X.27

0.6…4224 kbit/s7

G703-64-M6

G.703 co/contradir

64 kbit/s

HSSI-M6

TIA/EIA 612

0.6…8448 kbit/s

10Base-T Ethernet

64…2048 kbit/s

Mini LAN

Module9

The modules are electrically, but not mechanically, identical with the modules in the channel unit of the Tellabs 8100 system. The functions of these data interfaces are • V.110 rate adaptation for bit rates ≤ 56 kbit/s • CRC end-to-end monitoring possible with all bit rates • control signal transmission through the network (V.13 simulated carrier or in the V.110 frame) • interface, local and V.54 remote loops One end of the circuit can be any other data interface or a G.704 access point in another Tellabs 8120 mini node or in a Tellabs 8100 node. The circuit types can be • point-to-point (pp) • broadcast (bc) Tellabs 8120 mini node M does not the point-to-multipoint server functions as the channel unit in the Tellabs 8100 node. The interfaces, however, can be connected as end points to a point-to-multipoint circuit when the Point-to-Multipoint (pmp) Servers (branch points) are in the Tellabs 8100 nodes.

6The

interface module has been discontinued. maximum bit rate per module is 8448 kbit/s. This capacity can be divided between two channels in the modules V35-M, V36-M and X21-M. Tellabs recommends the HSSI-M module for usage above 2 Mbit/s bit rates as it offers the possibility to have more cable length. 8Tellabs recommends the HSSI-M module for usage above 2 Mbit/s bit rates as it offers the possibility to have more cable length. 9The technical name SMU-BRIDGE can be seen in Tellabs 8000 manager. 7The

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 16

22030_12 © 2013 Tellabs.

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

2.3.2

Framed Interface as Access Port Framed n x 64 kbit/s, 2 Mbit/s or 8 Mbit/s interfaces can be used as access interfaces in which case the interfaces are called G.704 access ports which means that there is no HDLC channel. In principle, the framed interfaces provide the same features as the corresponding trunk interfaces. A framed channel interface can offer several access ports. A 2 Mbit/s G.704 access port can comprise the following time slots and time slot fractions. Cross-Connectable Time Slot Fractions

XB

XD

n x 64 kbit/s

n x 64 kbit/s

n x (a, b, c, d)

32 kbit/s

32 kbit/s

a, b/c, d

16 kbit/s

16 kbit/s

a/b/c/d

8 kbit/s

8 kbit/s

-

A typical G.704 access port is a 2 Mbit/s interface for a digital PABX.

2.3.3

Rules for Mixing Different Interface Types Usually, both ends of the connection use the same interface type. In some cases it is possible to mix different interface types. Different electrical interfaces are not usually of major concern. At least the following points must be checked between both ends: • same use of control bits in V.110 frame • same XB/XD capacity • same XB framing of data circuits (V.110, modified V.110, no framing) The structure of the XB/XD channel is not normally transported outside the network. It is, however, very easy to do by using the G.704 framed access port. In this case the standard procedures should be used: • V.110 framing (≤56 kbit/s) • V.13 simulated carrier (V type interfaces ≥64 kbit/s) • X.30-specified X.21 C/I mapping (X.21 ≤48 kbit/s)

2.4 2.4.1

Applications Framed Interfaces There are different applications for the transmission rate and the features of the framed interfaces in Tellabs 8120 mini node M. Fig. 5 presents the different ways to interconnect two Tellabs 8120 mini node M devices. The same alternatives are available when connecting Tellabs 8120 mini node M to a Tellabs 8100 node.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 17

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

Fig. 5 Tellabs 8120 Mini Node M Trunk Lines

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 18

22030_12 © 2013 Tellabs.

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

BTE Modules The BTE modules10 serve baseband transmission at rates 128-4224 kbit/s. The frame structure is a modified G.704 frame, where the overhead of 64 kbit/s is used for the frame structure. The available transmission rate for the terminal equipment is the line rate subtracted by 64 kbit/s. The rate can freely be allocated between all access points by the cross-connection of the equipment. BTE-384-M uses biphase transmission for 2- or 4-wire lines at rates 128-384 kbit/s. The cable length can be up to 3.5-6 km depending on the cable type and the transmission rate. BTE-1088-M, BTE-2048-M, BTE-4096-M offer HDSL-like performance at rates 320-4224 kbit/s using 4-wire transmission, 2B1Q line code. BTE-2048-2W-M offers 2-wire full duplex operation over a single wire pair using echo cancellation. The cable length can be 3-10 km depending on the rate, module and cable characteristics. BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M offer HDSL-like performance at rates 320-2304 kbit/s using 2-wire full duplex transmission over a single wire pair. The line code is 2B1Q. BTE-1088-2W-M and BTE-2304-M offer also additional 4-wire modes at rates 320-2304 kbit/s. The cable length can be 4-10 km depending on the rate, module and cable characteristics. Using a BTE module, Tellabs 8120 mini node M can be connected to a Tellabs 8100 node with a corresponding interface, another Tellabs 8120 mini node or to table top baseband modems SBM 384A (with BTE-384-M), STU-2048 (with BTE-2048-M), STU-1088 (with BTE-1088-M), STU-320 (with BTE-320-M), STU-576 (with BTE-576-M), STU-1088-2W (with BTE-1088-2W-M) or STU-2304 (with BTE-2304-M). LTE-M11 The LTE-M module provides a line interface for a symmetrical pair cable. The transmission rates of the LTE module are 2048 kbit/s and 1088 kbit/s. The impedance of the transmission line is 120 Ω and the maximum attenuation of the transmission line can be -36 dB. The 2048 kbit/s interface complies with G.703/G.704 Recommendations. At the 1088 kbit/s rate a modified G.704 frame is used. Depending on the cable type and transmission rate, cable lengths of over two kilometers can be reached. G703-75-M and G703-120-M The G703-75-M and G703-120-M modules offer an interface with a transmission rate of 2048 kbit/s. The impedance of the transmission line is fixed (75 or 120 Ω, respectively). The maximum attenuation of the transmission line is 6 dB. The interface complies with the corresponding Recommendations G.703/G.704. The interface is designed for the interconnection of equipment in the same physical location.

10The production of the interface modules BTE-64-M, BTE-320-M, BTE-384-M, BTE-576-M, BTE-1088-M, BTE-1088-2W-M, BTE-2048-M, BTE-2048-2W-M, BTE-2304-M, BTE-4096-M and baseband modems SBM 384, STU-320, STU-576, STU-1088, STU-1088-2W, STU-2048 and STU-2304 has been discontinued. 11The production of the interface module LTE-M has been discontinued.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 19

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

G703-8M-M12 The G703-8M-M module is similar to G703-75-M but with a transmission rate of 8448 kbit/s. The impedance of the transmission line is fixed 75 Ω and the maximum allowable attenuation of the transmission line is 6 dB. OTE-LED-M The OTE-LED-M module is an optical fiber interface. Almost all fiber types which are suitable for data transmission (not plastic-coated fibers) can be used with this module. The connector is of type FC. Transmission distances of several dozens of kilometers can be achieved with an OTE module. The transmission rates are 2048 kbit/s and 8448 kbit/s, and the frame structure is according to G.704. V35-G704-SM and X21-G704-SM13 Tellabs 8120 mini node M can be equipped with a V35-G704-SM module, where the connection signal levels are according to the V.35 or V.11 Recommendations, the interface timing is codirectional and the connectors are of type D with 9 pins. The rate of the interface is n x 64 kbit/s (n = 2…33) and the frame structure is modified G.704. The interface is designed for the connection of Tellabs 8120 mini node M to the V series interface provided by the public data transmission network, using the bit rate of n x 64 kbit/s. The modules V35-G704-SM and X21-G704-SM have 2 23-1 type scramblers in both transmission directions. The scramblers can be used when the transmission rate is 31 x 64 kbit/s or lower except by the unframed mode, where the scramblers cannot be used. It is advisable to use the scramblers whenever it is possible. Special Modes The interfaces IF1 and IF2 of Tellabs 8120 mini node M can be connected to 1+1 protecting mode when both interfaces transmit the same data in the transmission direction. In the receive direction, however, the better one of the two received signals is selected for the terminal equipment interfaces. This duplication is used in order to protect the transmission. The protection can be realised with any two modules with the same transmission rate. The interfaces IF1 and IF2 can use the split trunk transmission method as well, where the signal from the terminal equipment interface is distributed to the two framed connections and returned at the receiving end in its original form. This facilitates a transmission where the transmission rate of the signal from the terminal equipment interface is higher than the rate of a separate framed interface. Restrictions for the maximum propagation time difference between the transmission lines of the framed interfaces are set. It is recommended that both interfaces use the symmetrical pairs located in the same cable.

2.4.2

Unframed Interfaces The unframed interfaces of Tellabs 8120 mini node M bit rates 600 bit/s…8448 kbit/s. Normally, Tellabs 8120 mini node M should be installed near the equipment in order to be accessed.

12The 13The

production of the interface module G703-8M-M has been discontinued. production of the interface modules V35-G704-SM and X21-G704-SM has been discontinued.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 20

22030_12 © 2013 Tellabs.

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

Unframed Channel Interface Types Interface Bit Rate kbit/s

Interface Type

XB Bit Rate kbit/s

Structure

Notes

0.6…4.8 7.2…9.6 14.4…19.2 38.4 48 56

V24, X21 V24, X21 V24, X21 V24, X21 V24, 35, 36, X21 V24, 35, 36, X21

8 16 32 64 64 64

V.110 V.110 V.110 V.110 V.110 V.110

1415

72 80 144 160

V35, 36, X21 V35, 36, X21 V35, 36, X21 V35, 36, X21

72 (+8 or 16) 80 (+8 or 16) 152 (+8) 160 (+8 or 16)

frame frame frame frame

17

n x 64 n x 64

V35, 36, X21 V35, 36, X21

n x 64 (+8,16 or 24) n x 64 (+8 or 24)

frame V.13

17

64

G.703 (co or contradir)

64 +(8)

-

17

1415 1415 1415 1615 1615

17 17 17

18

V.24/V.28 can be synchronous or asynchronous. The ITU-T-specified V.14 synchronous/asynchronous conversion is used. The C/I control signal mapping of the X.21 interface is done for bit rates ≤48 kbit/s according to the Recommendation X.30 (compatible with V.110). At bit rates 56 kbit/s and n x 64 kbit/s the C/I can be mapped through the network but it is proprietary. The XB structure in the table above refers to the framing or coding of data when it is mapped into the trunk. V.110 is a typical frame used for data connections and it is used in an ISDN network for the rate adaptation of V and X series interfaces. The framing is used between the access ports of the connection and it is not visible outside the trunks of the network. The end-to-end connection is monitored and supervised by the V.110 frame in the data interface types <64 kbit/s. With bit rates n x 64 kbit/s it is only possible to map the data into the XB/XD channel. It is, however, possible to map the data with an additional n x 8 kbit/s frame which includes end-to-end monitoring (CRC) and network-independent clocking for channels. The bit rate of the additional frame is presented below. Bit Rate of Additional Frame 105/109 Transfer

CRC

Network Independent Clocking

ON ON ON ON

ON

Rate ≤512 kbit/s Frame Rate kbit/s

Rate >512 kbit/s Frame Rate kbit/s

8

8

8

8

8

24

16

16

14A

special, modified V.110 framing can be used (CRC error monitoring is included). synchronous bit rates of up to 64 kbit/s are ed. 16A modified V.110 framing can be used (CRC error monitoring and network independent clocking). 17A separate 8, 16 or 24 kbit/s frame can be used (CRC, 105/109 and network independent clocking). 18Simulated carrier function according to Recommendation V.13 (can be turned off). A separate 8 or 24 kbit/s frame can be used (CRC and network independent clocking). 15Also

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 21

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

105/109 Transfer

Network Independent Clocking

Rate ≤512 kbit/s Frame Rate kbit/s

Rate >512 kbit/s Frame Rate kbit/s

ON

16

24

ON

ON

16

24

ON

ON

8

24

CRC

ON ON

The end-to-end monitoring supervises the XB/XD signal path through the network. A V.110 framed port does this by counting errored frames. The CRC monitored ports count errored CRC blocks which include every bit of the signal. Network independent clocking means that the ’s DTE equipment can provide timing for transmission data which is not frequency-synchronized to the network clock. The standard V.110 framing for low speed interfaces also s the network independent clocking. The typical applications for the low-speed interfaces V.24/V.28 (≤0.6…19.2, 38.4 kbit/s and n x 3.6 kbit/s) are • termination of point-to-point circuits in a data processing centre • end point of point-to-multipoint circuits in the Tellabs 8100 network • termination of V.110 formatted circuits The typical applications for the medium speed interfaces V.35, V.36 (≤9.6…38.4, 48, 56, and n x 64 kbit/s) are • termination of point-to-point circuits in a data processing centre • end point of point-to-multipoint circuits in the Tellabs 8100 network • links for data multiplexers, PADs, LAN bridges and routers • data links between two computers • trunks of low or medium capacity data networks The typical applications for the high speed interfaces V35, V.36, HSSI (64…8448 kbit/s) are • links for data multiplexers, PADs • links for LAN bridges, routers • data links between two computers • trunks of low or medium capacity data networks The typical applications for the LAN module (64…2048 kbit/s) are • LAN interconnection Low speed interfaces V.24/V.28 at rates n x 3.0 and n x 3.2 kbit/s may be used for access links to data networks using 6+2 (n x 3.2 kbit/s) or 8+2 (n x 3.0 kbit/s) signalling formats. Interfaces X.21 at rates 0.6, n x 1.2, 48, 64 and (n x 64) kbit/s may be used for X.21 access links to X.21 or X.25 data networks. In X.21 bis mode the X.21 interface may be applicable for a variety of applications with data multiplexers etc.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 22

22030_12 © 2013 Tellabs.

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

The G.703 interface is mainly used for transfer between the Tellabs 8100 network and another transport network or switching system based on the G.700 Series ITU-T Recommendations. Some computers and data multiplexers may also be equipped with a 64 kbit/s G.703 interface.

2.5

Network Synchronization Trunks use the synchronous octet interleaving; the buffer memories of the framed interfaces require that the average bit rate in the incoming signals is the same in all trunks (mesochronous clocks). The same requirement usually applies to the synchronous n x 64 kbit/s data interfaces ( access ports). Some data interface types allow the use of a plesiochronous clock in the access ports. Tellabs 8120 mini node M is provided with an internal master clock, which gives timing to the cross-connect switch. The master clock can be locked to • an external n x 64 kHz clock input • an incoming n x 64 kHz clock of a trunk or channel interface If the master clock is not locked to any external reference timing, the clock operates in an internal mode with an accuracy of ±30 ppm. The clock reference source is defined by a clock fallback list which can have up to five clock entries. The following clock faults are recognized: • loss of clock or signal • loss of frame alignment at a clock interface • far-end alarm concerning the loss of the reference clock of the node Two examples on the synchronization of Tellabs 8120 mini node M are given below.

Fig. 6 Independent Timing of Network Nodes

Nodes can be timed independently of one another. This practise can be used if an accurate station clock is available. In this practise the equipment uses exclusively the external clock input (EXT CLK). 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 23

2 Tellabs 8120 Mini Node M as Tellabs 8100 Network Element

Fig. 7 Synchronization through Trunk

The usual practise with two pieces of equipment is to synchronize one to the external clock or to use its internal clock. The other piece is synchronized to the trunk coming from the master equipment. Both pieces should not be synchronized at the same time to the trunk coming from the other end because it causes a closed timing loop and corruption of data transfer. The same practise can also be used if there are many pieces of equipment in the same network. One piece is the master and the clock is distributed via the network to the other pieces. The network is normally locked to an external clock source via the network master equipment or to the internal clock of the master. The clock distribution network can make use of reserve routes. A change-over is based on the clock faults criteria. The selection of the reserve clock route must be done so that the change-over to a reserve route does not cause a closed timing loop.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 24

22030_12 © 2013 Tellabs.

3 Operation

3 Operation 3.1

General The functional block diagram is presented in Fig. 8.

Fig. 8 Tellabs 8120 Mini Node M Functional Block Diagram

The common functional blocks of Tellabs 8120 mini node M are • G.704 framed interfaces IF1 and IF2 • cross-connect block • microprocessor block for control functions • keyboard and display • AC/DC power supply or DC/DC power supply 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 25

3 Operation

The microprocessor block, the cross-connect block and the G.704 framing block are located on the main board. Two changeable interface modules for framed interfaces are located on the main board and connected through connectors to the framing block. The power supply is a separate board connected through cables to the main board and covered with a metallic shield to prevent the main current causing a hazard when the case is opened. The keyboard and the display are on the front . The channel board and two changeable access interface modules are located over the main board and the framed interface modules. The cross-connect and microprocessor busses connect the channel board and the main board together.

3.2

G.704 Framed Interfaces IF1 and IF2 The G.704 framing block processes framed signals at 8448 kbit/s, 2048 kbit/s and n x 64 kbit/s. The block includes two independent transmission channels to carry data and also to provide an internal communication link of the Tellabs 8100 system. The transmission channel interfaces are independent of each other and they may, for example, be G.703 interfaces, optical interfaces, and, at certain speeds, also baseband interfaces. The framed signal which is carried on the transmission line is assembled and disassembled in the G.704 framing block. In the transmitting direction the Tx frame block creates a signal by mapping data from the X-bus into the correct time slots, adding frame alignment signal bits and the CRC check sum, and by generating the HDLC channel at a required position within the frame with the aid of the processor. In the receiving direction the Rx frame block searches the received signal for the frame synchronization word. When the synchronization is found, the Rx frame block can extract the data transmission time slots, check the CRC check sum, and recover and supply the HDLC channel to the processor. The frame structure and the use of the certain bits in the frame depend on the transmission speed. At 2048 kbit/s and 8448 kbit/s the frame structure is in accordance with G.704. A modified G.704 frame structure is used for other speeds. If required, it is also possible to remove the framing and have the channel to operate in transparent mode. In the G.704 framing block there are data buffers for the data transmission. The transmit buffers of the channels are used to store data so that there is always a time slot available to be transmitted by the Tx frame block. The transmit buffers also synchronise the phase of the transmitted frame with the phase of the X-bus and stuff idle data in the unused time slots of the frame. The receiving buffers of the channels store incoming data so that required time slots are always available for the cross-connect block. These buffers also form a flexible buffer in order to compensate for minor momentary speed differences between the X-bus and the received signal. The length of the receiving buffers can be changed in accordance with the application requirements. For instance, in some cases a minimum connection delay is required whereas in plesiochronous operation slips should occur as seldom as possible.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 26

22030_12 © 2013 Tellabs.

3 Operation

3.2.1

Frame and Multiframe Structure The unit has two independent G.704 framed interfaces. The frame has the following three modes. • 8448 kbit/s = 132 TS • 2048 kbit/s = 32 TS • n x 64 kbit/s = n TS The 2 Mbit/s and 8 Mbit/s frame structures conform with ITU-T G.704 Specification. The 8 Mbit/s frame structure is shown in Fig. 80 of Appendix 2 and the 2 Mbit/s frame structure in Fig. 81 of Appendix 2. For further details see Appendix 2. The 8 Mbit/s signal has four 2 Mbit/s groups (thirty time slots). The 2 Mbit/s frame has one signalling time slot (TS16), and in the 8 Mbit/s frame each group has its own signalling time slot (TS67…70). The main features of the n x 64 kbit/s frame are the same as those of the 2 Mbit/s frame. The frame length is n time slots. Possible signalling bits are in the last time slot of the frame, or in TS16, if n ≥18. The framed interface lines primarily use the following time slots for XB channels. 8 Mbit/s

TS 5…32, 34…65, 71…98, 100…131

Total 120 TSs

2 Mbit/s

TS 1…15, 17…31

Total 30 TSs

n x 64 kbit/s

TS 1…n-2 TS 1…15, 17…n-1

Total n-2 TSs if n ≤17 Total n-2 TSs if n ≥18

The table of Multiframe Structure in Signalling Time Slot in Appendix 2 shows the G.704 multiframe structure of the signalling time slot. For the transmission of the XD channels the following time slots are used: 8 Mbit/s

TS 67, 68, 69, 70

2 Mbit/s

TS 16

n x 64 kbit/s

TS n-1 if n ≤17 TS16 if n ≥18

The trunk lines always use the G.704 compliant CRC check in order to detect errors in the received signal and to prevent alignment to an imitative frame alignment word. On the access lines the CRC check can be turned off if the equipment does not the CRC frame structure. The CRC check is inserted into the different frame structures in the following way.

22030_12 © 2013 Tellabs.

Frame

Time Slot

CRC Check

8 Mbit/s

TS99

CRC-6

2 Mbit/s

TS0/B1

CRC-4

n x 64 kbit/s

TS0/B1

CRC-4

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 27

3 Operation

3.2.2

Buffers In the transmit direction the buffer supplies time slot data from the X-bus to the frame to be transmitted. When the cross-connect block supplies data to the X-bus, it also adds information about the location in the transmitted frame where the data is to be placed. The unit stores the data in its transmit buffer in a position corresponding to the position of the time slot in the frame. The frame multiplexing circuits will fetch the data when they are transmitting the corresponding time slot. As it is possible to write the data from the bus to any time slot position in the buffer, the buffer must control that the write and read operations do not simultaneously address the same time slot. The transmit buffer length is two frames. The frame multiplexing block reads the first frame area and the bus writes into the second frame area. This transmit buffer arrangement causes a delay of one frame (125 µs). In the receiving direction the buffer supplies received time slot data from the demultiplexed frame to the X-bus. When the cross-connect block via the X-bus requests data from the interface block, it also specifies the time slot concerned. Usually, the phase of the received frame does not coincide with the frame phase of the X-bus; on the other hand, the receiver writes the time slot data into the Rx buffer clocked by the received frame. Therefore, the Rx buffer has to control that the read and write operations do not collide, in spite of speed fluctuations and jitter. If the read and write addresses come too close, one of them has to be moved, in other words, centred. The centring is made by changing the read address, and the change is always one frame or a multiple of a frame. The centring causes a certain number of frames to be lost or retransmitted. Centring is required when equipment is powered up, when a received signal contains disturbances, or when the transmission is plesiochronous. If a plesiochronous system constantly exhibits a frequency difference in the same direction, the buffer has to be centred at regular intervals. The length of the interval depends on the frequency difference and on the buffer mode.

Frame Buffers The buffers have four operating modes. Buffer Mode

Rx Delay (Frames)

Tx Delay (Frames)

Usage

4 Fr19

1…3

1

Framed access interfaces, n x 64 kbit/s trunks

8 Fr

1…7

1

Special use

8 Fr/Split

2…6

1

Split trunk line components

64 Fr

1…63

1

Special use, e.g. small slip rate in plesiochronous use

In a plesiochronous system the interval between the centring situations is:

19Fr

= frame = 125 µs

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 28

22030_12 © 2013 Tellabs.

3 Operation

Buffer Mode

n x 64 kbit/s

2048 kbit/s

8448 kbit/s

4 Fr20

n x 8/df21

256/df

1056/df

8 Fr

4 x n x 8/df

1024/df

4224/df

8 Fr/Split

2 x n x 8/df

512/df

64 Fr

32 x n x 8/df

8192/df

The 4 Fr buffer is the normal mode of the buffer. A buffer with a length of eight frames is used for split trunk operation. It may also be used for other applications; it should be used if, for example, unusually large fluctuations have to be handled correctly or if the frame alternation has to be intact after the centring as well. The long buffer leads to a delay of up to 63 frames; thus, this buffer mode is recommended for special purposes only. The slip distance is very large in a plesiochronous system and the buffer is well suited for large frequency fluctuations. This buffer mode can be used at 2048 kbit/s and n x 64 kbit/s. Multiframe Buffers In the transmitting direction the signalling data is directed through the same buffer as the time slot data. The signalling multiframe of the frame to be transmitted is synchronized to the multiframe clock of the X-bus. The cross-connect block supplies the frame signalling data, along with the other time slot data of the frame. The framing block generates a synchronization time slot in the first frame of the signalling multiframe. Thus, the signalling data and the time slot data have equal delays in the transmitting direction. In the receiving direction the phase of the received signal multiframe usually differs from the phase of the X-bus multiframe. Thus, the received signalling data has to be buffered until the cross-connect block performs the cross-connect function for the data concerned. There are two alternatives for the multiframe buffer length: two and four multiframes. The multiframe buffer length depends on the selected length of the frame buffer. Frame Buffer Mode22

Multiframe Buffer Mode23

MFr-Rx Delay

MFr-Tx Delay

4…8 frames

2 MFr

0…2 MFr

1 Fr

64 frames

4 MFr

1…3 MFr

1 Fr

The time slot data and signalling data have separate buffers. Therefore, there are different delays in the processing of signalling data and time slot data. This means that the signalling data and the time slot data which are placed in a transmitted frame do not necessarily originate from the same frame.

20Fr

= frame = 125 µs = frequency difference between the signal received from the line and the receiving frequency generated by the master clock oscillator. 22The length of a frame is 125 µs. 23The multiframe length is 2 ms. 21df

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 29

3 Operation

3.2.3

Split Trunk Lines A split trunk line can be used to combine two parallel n x 64 kbit/s or 2048 kbit/s interfaces in order to increase the maximum number of time slots of a n x 64 kbit/s trunk interface. The time integrity of the time slots in the split trunk line is preserved even if the n x 64 kbit/s is connected through physically separated cables. The split trunk mode can be used for line speeds n x 64 kbit/s and 2048 kbit/s when a frame with CRC4 is used. The split trunk mode always requires long buffers (8 frames). One of the interfaces will function as a master and the others as slaves. Split components must have the same bit rate. The interfaces are synchronized to each other by their CRC4 multiframe structure. In the transmitting direction the interface transmit buffers and the Tx frame multiplexers are synchronized with the X-bus MSYN signal to transmit in the same multiframe phase. In the receiving direction the master interface sends information about its receiving buffer read phase to the slaves, which will centre their own receiving buffers to the same phase. This operation causes data time slots sent from a transmitting node in the same frame to be read together within one frame into the cross-connect block of the receiving equipment. Theoretically, the maximum delay allowed between lines in a split trunk line is 0.5 frames. Due to technical reasons, however, the maximum delay is 50 µs. Each line of a split trunk line will handle its own signalling data. Those lines which carry one or more data channels with signalling data will use the last time slot, or TS16, if it is possible, as a signalling channel with a multiframe structure. It is not necessary to use a CAS time slot for lines that do not include data channels with signalling. When making cross-connection for a split trunk, a unidirectional channel from the control port of the master channel to the control port of the slave channel must be created. The port numbers for data ports of interfaces correspond to the interface numbers. In Tellabs 8120 mini node M the control port numbers are 20 for IF1 and 21 for IF2.

3.2.4

1+1 Protection The interface can be 1+1 protected by another framed interface. In the protected mode both channels must have the same rate and framing mode settings. Framed interfaces working in the protected mode will look like one cross-connect port towards the X-bus. In the protected mode both channels transmit the same data signal coming from a buffer. Both channels use their own frame mux to create the frame structure. The receiving direction includes a change-over switch that selects the active receiver. Rx signal faults are classified into several categories. The switch uses fault categories to select the interface to be used. The fault categories are indicated in the fault table. For example, 1.x means first category, the worst or most serious fault.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 30

22030_12 © 2013 Tellabs.

3 Operation

Fig. 9 Protection Mode of Framed Interfaces

The operating modes of the change-over switch are • normal operation • prefer operation • forced operation In normal operating mode the switch will automatically switch to the other interface if the Rx signal fault category (1, 2, 3, 4, 5, OK) of the active interface is continuously worse than the fault category of the other interface for a longer period than the given time delay. No switch-over operation is activated when the categories are the same for both interfaces. In prefer operating mode a switch-over is triggered if there is a difference between the interface fault categories. The better interface is switched into being active. In a situation with equal fault categories for both interfaces the switch selects the preferred interface. In forced operating mode the switch is forced to switch over without delay. Received data from the active interface is immediately connected to the X-bus. In this situation the Protection Switch Forced fault message with status MEI (maintenance event information) appears, and the red LED is turned on. A switch operating time delay is defined for the prefer and normal operating modes. The delay is defined as n x 10 ms, where n = 0…6000; in other words, the delay is 0…1 minutes. The delay defines the allowed fault duration before the switch is triggered to switch-over.

3.3

Operation of Framed Interfaces Tellabs 8120 mini node M is connected to a transmission line through interface modules. The interface modules contain the analog components required for the interface and also the analog components needed for generating the input and the output clocks. The signals between the framing block and the interface module are digital signals which are converted to the transmission line level in the module. Line codes are coded/decoded in the framing block when modules of G.703 type or optical modules are used; in baseband modules the line coding is performed in the module. Each module type s defined transmission rates which can be selected with the interface. The codes and the available transmission rates are described in Technical Specifications.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 31

3 Operation

The processor bus is connected to both interface module connectors. Through this bus it is possible to detect the module type and to read data regarding the module status, e.g. a missing incoming signal. Parameters which define the module functions, e.g. the transmission rate and possible looping commands, can be selected through the bus. In the receive direction the interface module regenerates the coded signal received from the transmission line and transforms the signal to the digital level. The module monitors the level of the received signal; if it is too low or missing completely, the module sets an AIS signal to the framing block and at the same time activates a missing signal alarm via the processor bus.

Fig. 10 Data and Clock Processing in the Receive Direction

The receive direction clock is recovered from the data in the interface module. The clock is supplied to the framing block, which uses it to decode the line code and to demultiplex the frame. If there is no received signal, the interface module replaces the received clock with the transmitted clock. The receive clock in the V series modules is taken from the circuit 113 from line. The missing signal alarm with V series modules is based on detecting the incoming clock signal. The received clock from both framed interfaces is connected to the synchronization bus where the processor can select a desired clock to be used as a synchronization signal for the master clock of the equipment. The clock to the synchronization bus is disconnected if there is a received signal failure. The framing block generates the frame structure for the data in the transmit direction. The line code of the data is generated in the framing block for G.703 interfaces and for optical interfaces. The coded digital data is connected to the interface module where it is converted to a line level signal. NRZ data for baseband interfaces is connected to the interface module where it is coded and transformed into a line level signal.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 32

22030_12 © 2013 Tellabs.

3 Operation

Fig. 11 Transmit Direction Clock and Data Generation at 8448 kbit/s

The transmit direction clock generation depends on the interface module and the transmission rate. In all cases the transmit direction clock is phase-locked to the C16M frame clock received from the X-bus. The transmit direction clock for 8448 kbit/s is usually generated by dividing the bus clock C16M by two. This divided clock is used to create the frame and to generate the output pulses in the coder. If the C16M clock is missing, the output clock is generated by using the oscillator of the interface module, which then is used to create the frame and to generate the output pulses in the coder. If the C16M clock is missing, a frame is transmitted, but the time slot data and possible multiframe signalling are set to AIS.

Fig. 12 Transmit Direction Clock and Data Generation at 2048 kbit/s

The transmit direction clock for 2048 kbit/s and 1088 kbit/s is generated by the phase-locked crystal oscillator of the interface module. The oscillator is locked to the C16M clock of the bus which is used to create the frame and to generate the output pulses in the coder. Even if the C16M clock is missing, the output signal is generated with the aid of the clock signal from the interface module crystal oscillator. The phase-locked oscillator will then be adjusted to its nominal frequency and the time slot data in the frame is set to AIS. 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 33

3 Operation

Fig. 13 Transmitting Direction Clock and Data Generation in Baseband Modules

The clock which is used to create the frames for baseband modules is generated in the framing block by dividing the C16M bus clock by a programmable divider to the nominal transmission rate. This clock signal and the data to be transmitted are supplied to the module, where the phase-locked oscillator is locked to the clock. The clock, again, is generated by the framing block. The line coded data is then generated with the aid of the phase-locked oscillator clock signal. If the C16M clock is missing, the clock generated by the module is connected to the framing circuit. The output signal rate is adjusted to its nominal value, and the frame and a possible control channel are transmitted, but all other data is set to AIS. The transmit direction clock for V35-G704-SM and X21-G704-SM modules is generated by dividing the C16M clock by a suitable divider. This clock is used as the transmit clock of the module in circuit 115. The dividing process may cause some jitter to the clock in this case. If the C16M clock is missing, no signal or clock is sent from the module.

3.4

Unit Controller The unit is controlled with an 80C186 microprocessor. The system program is stored on the board in two interchangeable EPROM memories. The application programs are stored in non-volatile FLASH memories; it is thus possible to update these programs without opening the case of the device. The non-volatile memory is also used to store the operating parameters and the serial number of the unit. In case of power interruption the unit is automatically reset to the conditions prevailing before the interruption, without specific parametrisation. The RAM memory of the processor operates as a working storage containing e.g. error counters and data buffers for the HDLC links and the frame control bus. The unit includes a multichannel analog-to-digital converter (A/D) which monitors the operating voltages and also the control voltage from the interface module connectors. The control voltage is, for instance, a voltage received from a baseband module controlling the baseband line power-off situation.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 34

22030_12 © 2013 Tellabs.

3 Operation

3.5

Cross-Connect Block The cross-connect block has the following main functions: • cross-connection of XB and XD channels • control of the cross-connect bus • master clock oscillator of the unit • interface for external clock input and output • selection of a reference signal for the master clock oscillator • selection of a clock signal for the external clock output The cross-connection is done in the switching matrix of the cross-connect block. The cross-connection bus contains approximately 1050 cross-connectable time slots (8-bit bytes). The bits from the interface blocks are collected by using this bus. The cross-connect switch combines the needed new bytes for the interfaces by using 8 kbit/s granularity. Usually, whole time slots or bytes are cross-connected. The delay caused by the cross-connection is one 8-kHz frame (125 µs). The cross-connect block exchanges data with the interface units by placing a channel address on the X-bus which activates the data buffers of the corresponding channel. Received and transmitted data is carried on separate 8-bit-wide busses. The G.704 framing block receives from the cross-connect block the time slot address which directs the bus data transmission to one selected time slot at a time. The cross-connect block supplies the C16M bus clock through the X-bus. The C16M clock is also the central clock of the equipment; it is used to create clock frequencies for the transmitted signals. The bus supplies frame alignment and multiframe alignment signals to the frame buffers. Bus functions are also monitored by the interface blocks. When the interface is synchronized and the corresponding cross-connection is made, the unit will activate the IA Activity Missing alarm if it cannot receive its channel address from the bus. The interface blocks monitor the combined information formed by the bus clock and multiframe synchronization signal; if this information is missing, the unit will activate the Bus Sync Missing alarm.

3.5.1

Cross-Connection The cross-connect block executes the cross-connection commands from the NMS or from the front interface. The cross-connect commands are stored in a non-volatile memory. By means of cross-connection the data of the access interface is placed in the selected time slots of the framed interface or in an another access interface. Time slots from a framed interface can also be connected to freely selectable time slots of another framed interface. Thus, the data from the framed interface can consist of data from several interfaces, and some time slots can be unused. In this case the free TS data, which can be defined in the interface, is placed in the unused time slots. The port is a description of interface properties for the cross-connection block. Every interface has one or more cross-connect ports. The port numbers for framed interfaces are 1 and 2, corresponding to the interface numbers IF1 and IF2. These port numbers are used to specify the port used by the payload data of the interface. The port numbers for access interfaces are dependent on the used channel board and access interface modules. Other port numbers are reserved for control channels.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 35

3 Operation

The cross-connection ports are defined by using interface definition, TS definition and a possible bit mask (n x 8 kbit/s connections). If need be, the cross-connection commands can include the signalling bits. The bit mask means a combination of eight bits, where state 1 indicates an 8 kbit/s channel of a time slot which is connected; state 0 means capacity left free. The mask can also be presented in hexadecimal format. The cross-connect types ed by the unit are 1.

Bidirectional connection: interface/(TS/bits) ⇔ interface/(TS/bits)

2.

Unidirectional connection: interface/(TS/bits) → interface/(TS/bits)

The n x 8 kbit/s and n x 64 kbit/s groups mapped by the interfaces are called the XB channel. The XB channel can be a combination of 64 kbit/s and 8 kbit/s signals. If the interfaces are equipped with signalling or control signals, they are either mapped to the XB channel or to the corresponding signalling bits (n x 500 bit/s) of the XD channel. In the latter case the signals are mapped to the G.704 compliant multiframe of the 2 or 8 Mbit/s trunk. The n x 500 bit/s signalling bits are called the XD channel of the interface. The number of the signalling bits depends on the capacity of the XB channel. Signalling bits are reserved for the XB channel in the following way. XB Capacity

XD Capacity

TSn/B1…B8 64 kbit/s

4 bits (a, b, c, d bits in G.704 structure)

TSn/B1…B4 32 kbit/s

2 bits (a, b)

TSn/B5…B8 32 kbit/s

2 bits (c, d)

The a, b, c, and d bits of the XD channel in the G.704 multiframe correspond to the XB channel time slots in the G.704 frame. The capacity reserved by XB and XD channels is determined by the interface type and the requirements. Four signalling bits are reserved for each time slot. Even if only some of the bits are needed, all four bits are cross-connected and transferred to the far-end channel interface. Port Locking After the operator has changed the parameters of the interface to the desired state, the parameters of the interface must be locked. This means that the properties of the port are transferred to the cross-connect block which needs the information for capacity allocation. The cross-connect cannot be made before the port is locked, and the port cannot be unlocked if there are any cross-connections made to the port. The parameters of the interface can be changed if the port is in unlocked state. Split Trunk Connection In split trunk mode there is always a master and a slave. The data buffer of the slave follows the action of the master interface through a control channel created by the cross-connection. The control channel is made by unidirectional connection command, and its direction is from master to slave. In Tellabs 8120 mini node M the control port number is 20 for IF1and 21 for IF2. Protection Connection The framed interfaces in protected mode will look like one cross-connect port towards the X-bus. A cross-connect command made to one port causes a cross-connection to both interfaces. The port number for the protected ports is 1.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 36

22030_12 © 2013 Tellabs.

3 Operation

3.5.2

Master Clock Synchronization The 16 MHz master clock of the equipment is used for generating the timing of the cross-connect bus. The timing consists of • 16 MHz • 8 kHz frame synchronization • 500 Hz multiframe synchronization The 16 MHz clock is also used to generate the Tx clock of each data interface. The master clock is usually synchronized to an incoming data signal (generally a 2 Mbit/s trunk, see 2.5 Network Synchronization on network synchronization). The clock of the desired interface is derived by using a separate sync clock bus. The cross-connect block controls the status of the synchronization clock and tells the required interface to connect the received clock of the interface to this bus.

Quality Level (QL) of Clock Signal When a HDLC channel is used at interface (IF1…IF3) and the Message Sending option is activated, Tellabs 8120 mini node M may receive messages from its neighbour node. Some of these messages include information about the clock signal to which this neighbour node is synchronized. This information is called Quality Level (QL) and it has been defined as numerical values from 1 to 7 where 1 is the highest and 6 the lowest one (7 means do not use this clock; the figure is used to prevent timing loops). If for some reason the neighbour node changes its clock signal used for synchronization, the QL of this new reference clock is transmitted via the HDLC channel. Tellabs 8120 mini node M polls these QL values from all the interfaces and thus can select the best available clock signal. The clock signal which has the highest QL and whose status is OK is the one to which the master clock is synchronized. If clock signals have the same QL, the clock to which it is synchronized is the one with the highest priority according to the fallback list. Whenever all the clock signals are available for synchronization (the status of the clocks is OK), there is no activated alarm related to the master clock even if the last entry of the fallback list would be used. The QL of the clock signal from an interface which does not use the HDLC channel is fixed to value 1. The QL of the internal clock is normally fixed to 6. Clock Fallback List The clock fallback list defines the interfaces which can be used for synchronization. It also describes the priority order for situations where two or more clock signals have the same QL. The list can have up to five entries. The form of the list is • 1. IF_ • 2. IF_ • 3. IF_ (Internal) The last entry is automatically followed by the internal state. 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 37

3 Operation

3.6

Operation of Unframed Channel Interfaces IF3-IF6 The channel interface board accesses unframed signals at rates 0.6 kbit/s…8448 kbit/s. It s four independent data transmission interfaces. The board can take two interface modules, both ing two channel interfaces. The available interface types V.24, V.35, V.36, X.21, G.703 (64 kbit/s), HSSI or 10Base-T interfaces. Note that the HSSI-M interface module and Mini LAN Module only one channel per module. signals at bit rates below 64 kbit/s are rate-adapted in accordance with the frame structure V.110/X.30. The V.110 signals are transported as 8, 16, 32 or 64 kbit/s across the network. The n x 64 kbit/s signals are transported at the rate across the network. Whenever required, the equipment s end-to-end CRC supervision of the signals and plesiochronous data timing. At rates below 64 kbit/s the CRC and plesiochronous timing features are ed in the V.110 frame. At higher rates an extra transmission capacity of 8, 16 or 24 kbit/s is required across the network. Asynchronous start-stop signals are ed at bit rates below 256 kbit/s. The basic functional blocks of the channel board are • data formatting circuitry • bus interfaces • interface modules Data Formatting Circuitry The data formatting circuitry determines the majority of the characteristics of the data interfaces provided by the channel board. The data formatting circuitry is described in more detail in 3.6.1 Data Formatting Functions. Bus Interfaces The bus interfaces perform the adaptation between the data formatting circuitry and the data bus and the address bus of the main board of the equipment. There are also data and address busses for the microprocessor controls. The master clock of the equipment can be synchronized to the clock received from the unframed interfaces through the sync bus. Interface Modules Tellabs 8120 mini node M accesses the physical interfaces through the interface modules. The interface modules convert the CMOS level data, timing and control signals to balanced or unbalanced V.11, V.28, V.10, or G.703, according to the requirements for each interface type. The receiver circuits convert the incoming signal levels to CMOS level data, clock and control signals. The interface module monitors the existence of the received signal level; if the signal is missing, a power off signal indication is given to the unit controller. The interface signal coding (e.g. G.703 co- and contradirectional operation, or sync/async converter) is performed in the channel board. There is an additional 16-bit input buffer on the V24-DTE-M module. This buffer can be used if the buffer length in the base unit is not sufficient.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 38

22030_12 © 2013 Tellabs.

3 Operation

3.6.1

Data Formatting Functions The data formatting circuitry provides the main data processing functions: • rate adaptation and framing • CRC monitoring • V.13 simulated carrier • bit rate generation • interface signal coding (e.g. G.703) • sync/async conversion • V.54 and X.21 test loops • test pattern generation and error counting

Fig. 14 Functional Block Diagram of Channel Board

Rate Adaptation and Framing

Bit Rates <64 kbit/s Data bit rates ≤64 kbit/s are, using the ITU-T Method V.110, rate-adapted to 8, 16, 32 or 64 kbit/s which can be handled by the cross-connect block and the routing tools. The V.110 frame is transparently transported through the network and can be used for the end-to-end monitoring of the channel quality. 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 39

3 Operation

The V.110 frame offers three channels for the transfer of the control signals. They are called SA, SB, and X. The channel SA carries the signals 108/107 and the channel SB the signals 105/109. The channel X carries both the signal 106 and the far-end alarm. The signal 106 is either derived locally from the signal 105 or from the channel X received from the far-end. When 105 is turned on, the locally generated 106 signal is delayed until 105 is sampled by the framer. This generates the minimum 106 delay which guarantees that 109 is turned on before the first data bit is received at the far end. When the 107/108 transfer is not required, both SA and SB (SA+SB = S) may carry the 105/109 or C/I signal, enabling the minimum control signal delay. The S signal is sampled once for each byte of data. In the management menus this mode is called V.110S or X.30, and the basic V.110 mode simply V.110. The V.110 or V.110S configurations use bit oriented data buffering with a 2 bit jitter/wander margin. The byte oriented data buffering is used in X.21 applications or when octet timing is desired. The byte oriented buffering and minimum control signal delay is called X.30 as the mode conforms to the CCITT Recommendation X.30. data rates < 600 bit/s are transferred by sampling at rate 4800 bit/s. Rates 0.6 kbit/s, n x 1.2 kbit/s (up to 38.4 kbit/s), and 48 kbit/s are ed in V.110, V.110S and X.30 modes. rates n x 3.0 kbit/s (data network formats 8+2 bits), n x 3.2 kbit/s (data network formats 6+2 bits) and n x 3.6 kbit/s (including rates 3.6, 7.2, 14.4 and 28.8 kbit/s) are ed in modes V.110 and V.110S. At 56 kbit/s both ITU-T V.110b and V.110c (b, c refer to V.110 table 7b and 7c) framing is ed. Bit Rates n x 8 kbit/s At rates 8, 16, 32 kbit/s the data is transferred in one, two or four bits of a time slot. At rates 72 and 80 kbit/s the data is transferred using one full time slot and one or two bits of another one. Rates 144 and 160 kbit/s need two full time slots and three or four bits of a third one (144 kbit/s uses one extra bit due to an ASIC restriction). No data framing is needed for the data transfer. The rates 48 kbit/s and 56 kbit/s are selected as 6 x 8 and 7 x 8 kbit/s in the management menu. Bit Rates n x 64 kbit/s At n x 64 kbit/s (rates 64…2048 kbit/s) the unframed data is transferred in 1…32 time slots. The data buffer length may vary from three to sixty-four bytes. The nominal buffer length selection allows for 18 µs, or at minimum one byte of jitter and wander. Bit Rates n x 64+8 kbit/s The n x 64+8 kbit/s rate is basically intended for the T1 rate 1544 kbit/s. Certain other n x 64+8 kbit/s rates are also ed. This mode uses n full time slots and one extra bit.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 40

22030_12 © 2013 Tellabs.

3 Operation

CRC Monitoring The channel board can end-to-end CRC monitoring of the data. The CRC-4 procedure used is similar to the one for the G.704 2-Mbit/s frames. At rates < 1.2, n x 1.2, n x 3.0, n x 3.2, and n x 3.6 kbit/s, the CRC check sum is transferred on the last five bits of frame alignment signal of the V.110 or X.30 frame. A modified V.110 frame is used at rates 48 and 56 kbit/s. When transferring the CRC check sum, the frames are called V.110M or X.30M, because the corresponding ITU-T frames do not CRC monitoring. At n x 64 kbit/s and n x 64+8 kbit/s the CRC check sum is transferred end-to-end in a proprietary Martis frame, using 8 kbit/s extra XB capacity. The end-to-end performance monitoring is based on the end-to-end CRC monitoring, when activated. Channel associated end-to-end CRC monitoring is the only way to get accurate performance characteristics for a channel. Performance data is expressed in of G.821 parameters. Control Signals The unframed interfaces control signals for the following channels: • 105/109 transfer at all bit rates (X.21bis) • 108/107 transfer at V.110 based frames (X.21bis) • 106 locally generated • 106 transfer from the far-end (V.110 only, X.21bis) • C/I at X.21 interfaces and bit rates 0.6, n x 1.2, 48 and n x 64 kbit/s The control channels can be transferred in several ways, depending on the bit rate. The SA, SB and X bits are normally used (selection V.110, X.30) with V.110, V.110M, X.30, X30M frames. The V.13 simulated carrier or an 8 kbit/s channel are used at n x 8 and n x 64 kbit/s rates. The 8 kbit/s channel requires additional transmission capacity but it offers a continuous channel which is, for example, required for X.21 applications. V.13 Simulated Carrier The V.13 simulated carrier is an inband transfer method which does not require extra capacity. When 105 is turned off, the data is substituted by a pseudo random pattern. When 48 bits of that pattern have been received, 109 is turned off and the data (104) is blocked to off state. When 105 turns on, the pattern generator input is changed from 1 to 0 for 8 bits. After that 106 turns on, and the channel is ready for the transfer of the data. If, due to transmission errors, the receiving end misses the turn on sequence, it will automatically return to on state when more than 31 errors have been detected in the pseudo random pattern during a certain time period. 106 Delay Normally, the minimum 106 delay required to guarantee proper operation is used. Whenever required, an additional delay may be selected in the range of 8…8000 bits. The delay is expressed in time units at the management interface. 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 41

3 Operation

105 Supervision In some applications 105 should continuously stay in on condition. If desired, the channel board can monitor the 105 state and generate an alarm if 105 goes off. Bit Rate Generation A variety of bit rates is required for the unframed interfaces. The data timing signals are derived from the 16896 kHz system clock by built-in programmable frequency synthesisers. There is a synthesiser for each channel and each transmission direction. Timing Sources Depending on the configuration, the timing signal for the incoming data (Tx direction) can come from the equipment or from the clock source of the channel board. The clock for the outgoing data (Rx direction) can come from the channel board or it can be taken from the Tx clock received from the . Plesiochronous Clocking When the data clock cannot be synchronized to the master clock of Tellabs 8120 mini node M, the plesiochronous operation (the same nominal bit rate) is required. The equipment s the transfer of plesiochronous clocking at all bit rates except for at 8, 16 and 32 kbit/s. Plesiochronous transfer is ed in the standard ITU-T V.110 frame at rates n x 1.2, n x 3.2, and n x 3.6. A Martis modification of V.110 (V.110M) also s plesiochronous clocking at n x 3.0, 48 and 56 kbit/s. An extra 8 kbit/s channel with the Martis frame is required at rates n x 8 kbit/s and n x 64 kbit/s. The 8 kbit/s channel s both CRC monitoring and plesiochronous timing at bit rates of up to 512 kbit/s. With rates above 512 kbit/s plesiochronous clocking requires a 24 kbit/s channel. The V.110 method of transferring the data phase and stuffing is used at all bit rates. The synthesisers operate in a digital PLL mode with slight jitter filtering of the input clock before phase comparison with the system reference clock. At the receiving end the synthesiser adjusts its phase according to the value received from the far-end. The phase adjustments take place in small steps in order to minimize the phase jitter amplitude and frequency spectrum width. With plesiochronous clocking the V.110 data buffer operates in bit mode. At n x 64 kbit/s rates the data buffer operates in a so-called frame synchronous mode where the data transferred during one X-bus frame form a block. The stuffing bits are deleted and inserted at the border between two blocks. Async/Sync Conversion The asynchronous/synchronous converter samples the incoming signal at 16 times the rate. The converter recognizes the start-stop pattern which may have start-stop bits and 6, 7, 8 or 9 data bits. Each detected erroneous pattern start-stop is considered as an input signal code error.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 42

22030_12 © 2013 Tellabs.

3 Operation

In case of overspeed, the stop bits are deleted at certain intervals. The receiving side adds the deleted stop bits and compensates for the overspeed by shortening the stop bits of the eight consecutive characters. The method allows for 1.25% overspeed. At underspeed additional stop characters are inserted. In extended operation mode, the stop bits can be deleted from every fourth character enabling 2.5% overspeed. The async converter can be used at bit rates 600 bit/s…64 kbit/s, 128 kbit/s and 256 kbit/s. At bit rates below 600 bit/s the async converter is by-ed and the data is sampled at the rate of 4800 bit/s.

3.6.2

Data Interfaces The interface signals of V.24/V.28, V.35, V.36 and X.21 interfaces are NRZ coded. Data and control signals can change their states at the edge of a clock period. The clock signal has a falling edge at the beginning of a period and a rising one in the middle of the period. The interface modules convert the CMOS level signals to appropriate interface signals. Interface Module Signal Levels Signal Name

Interface Type V.24/V.28

V.35

V.36

X.21

HSSI

103

V.28

V.35

V.11

V.11

TIA/EIA-612

104

V.28

V.35

V.11

V.11

TIA/EIA-612

105

V.28

V.28

V.11

V.11

TIA/EIA-612

106

V.28

V.28

V.11

V.11

TIA/EIA-612

107

V.28

V.28

V.11

V.11

TIA/EIA-612

108

V.28

V.28

V.11

V.11

TIA/EIA-612

109

V.28

V.28

V.11

V.11

TIA/EIA-612

113

V.28

V.35

V.11

V.11

TIA/EIA-612

114

V.28

V.35

V.11

V.11

TIA/EIA-612

115

V.28

V.35

V.11

V.11

TIA/EIA-612

140

V.28

V.28

V.28

-

TIA/EIA-612

141

V.28

V.28

V.28

-

TIA/EIA-612

142

V.28

V.28

V.28

-

TIA/EIA-612

The data and clock signals for G.703 outputs come as positive and negative CMOS level pulses from the base unit. By the aid of drivers and transformers the control signals are converted to G.703 signals. The G.703 input signals are converted to CMOS signals using comparators.

3.6.3

Timing Modes The clocking mode of data interfaces depends on the type of interface, on the type of the interfaced equipment and on the operation mode. The clock may be considered to be locked to the network timing source if

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 43

3 Operation

1.

the equipment uses the clock supplied by the network interface

2.

the system and the network use the same timing source, e.g. a national timing distribution network

3.

both the system and the network are locked to the timing source according to the CCITT Recommendations G.811 and G.823

V Series Interfaces In most cases the unframed V series interface (V.24/V.28, V.35, V.36) is connected to a DTE as if it were a data modem (DCE). The data interface is clocked from the network. The clocking method can be used when the transfer delay between the DCE and DTE is below 0.15 bit (L < 30/(bit rate) m); bit rate in Mbit/s. The timing mode is called synchronous 114/115. • Data in the direction DCE to DTE (104) is clocked by the timing signal 115. • Data in the direction DTE to DCE (103) is clocked by the timing signal 114 from the DCE (IF module). At longer DTE-DCE distances and in applications where the DTE terminates a data circuit with clock looping at the far-end, or it is clocked by a timing source locked to the same source as Tellabs 8120 mini node M, the clock 113 is used in the direction DTE-DCE instead of 114. The signals in the direction DTE-DCE may contain jitter and wander when compared to the DCE-DTE timing. The timing mode is called 113/115 mesochronous. • Data in the direction DCE to DTE (104) is clocked by the timing signal 115. • Data in the direction DTE to DCE (103) is clocked by the timing signal 113.

Fig. 15 Contradirectional Synchronous and Codirectional Mesochronous Timing of an Unframed Data Interface in DCE Mode

Fig. 16 Contradirectional Synchronous and Codirectional Mesochronous Timing of an Unframed Data Interface in DTE Mode Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 44

22030_12 © 2013 Tellabs.

3 Operation

When interfacing a DCE, the interface module may operate either as a DCE (signals cross-connected in the interface cable) or as a DTE (without signal cross-connection in the interface cable). The timing signals may, in contradirectional mode, come from the DCE to the interface module (cases 115/114 EXT or 115 EXT), or, in codirectional mode, from both the DTE and DCE (115/113). Currently, only the V.24 DTE interface is available.

Fig. 17 Codirectional Plesiochronous Timing of an Unframed Data Interface

A data source (DTE or DCE) which cannot be synchronized to the Tellabs 8100 network is accessed using plesiochronous timing. In plesiochronous mode only codirectional timing is ed. Asynchronous V Series Interface The asynchronous operation is ed at bit rates of up to 256 kbit/s. The timing signals are switched off in the asynchronous mode. X.21 Interface

Fig. 18 Timing of an X.21 Unframed Data Interface 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 45

3 Operation

Only one clock signal is used in X.21 mode. The clock comes from the interface module or towards it. The clock is always locked to the same source as the clock of Tellabs 8120 mini node M. When required, octet timing may also be used. G.703 Interface

Fig. 19 Timing of a 64 kbit/s G.703 Unframed Data Interface

The G.703 interface at 64 kbit/s s co- and contradirectional operation. Octet timing is also ed.

3.6.4

Rate Adaptation and Mapping The frame structures used are described in Appendix 1. The signals and control signals in the channel board are rate-adapted and mapped as follows. Rate Adaptation and Mapping at Bit Rates ≤48 kbit/s Rate kbit/s

Rate Adaptation Method

XB Mapping kbit/s

Control Signals

Plesiochronous Clocking

< 0.6

V.110

1x8

SA, SB, X

No

0.6, 1.2, 2.4

V.110

1x8

SA, SB, X

No

0.6, 1.2, 2.4

X.30

1x8

S

No

4.8

V.110

1x8

SA, SB, X

Yes

4.8

X.30

1x8

S

No

9.6

V.110

2x8

SA, SB, X

Yes

9.6

X.30

2x8

S

No

19.2

V.110

4x8

SA, SB, X

Yes

19.2

X.30

4x8

S

No

38.4

V.110

8x8

SA, SB, X

Yes

38.4

X.30

8x8

S

No

3

V.110

1x8

SA, SB, X

Yes

6

V.110

2x8

SA, SB, X

Yes

12

V.110

4x8

SA, SB, X

Yes

24

V.110

8x8

SA, SB, X

Yes

3.2

V.110

1x8

SA, SB, X

Yes

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 46

22030_12 © 2013 Tellabs.

3 Operation

Rate kbit/s

Rate Adaptation Method

XB Mapping kbit/s

Control Signals

Plesiochronous Clocking

6.4

V.110

2x8

SA, SB, X

Yes

12.8

V.110

4x8

SA, SB, X

Yes

25.6

V.110

8x8

SA, SB, X

Yes

3.6

V.110

1x8

SA, SB, X

Yes

7.2

V.110

2x8

SA, SB, X

Yes

14.4

V.110

4x8

SA, SB, X

Yes

28.8

V.110

8x8

SA, SB, X

Yes

End-to-end CRC monitoring can be ed at all bit rates mentioned above. The CCITT/ITU-T Rec. V.110 and X.30 do not CRC monitoring. The frame type is renamed V.110M, or X.30M when CRC is activated. Rate Adaptation and Mapping at Bit Rates ≥48 kbit/ Rate kbit/s

Adaptation Method24

XB Mapping kbit/s

Control Signals

CRC

Plesiochronous Clocking

48

V.110

1 x 64

SA, SB, X

No

No

48

V.110M

1 x 64

SA, SB, X

Yes

Yes

No

No

56

V.110/7b

1 x 64

-

56

V.110/7c

1 x 64

SA, SB, X

No

No

56

V.110M

1 x 64

SA, SB, X

Yes

Yes

64

-

1 x 64

-

No

No

64

MartisDXX

1 x 64+ 8 + 8

SB

Yes

Yes

72

-

1 x 64+1 x 8

-

No

No

72

MartisDXX

1 x 64+1 x 8+ 8 + 8

SB

Yes

Yes

80

-

1 x 64+2 x 8

-

No

No

80

MartisDXX

1 x 64+2 x 8+ 8 + 8

SB

Yes

Yes

144

-

2 x 64+3 x 8

-

No

No

144

MartisDXX

2 x 64+3 x 8+ 8

SB

Yes

Yes

160

-

2 x 64+4 x 8

-

No

No

160

MartisDXX

2 x 64+4 x 8+ 8 + 8

SB

Yes

Yes

N x 64

-

N x 64

-

No

No

N x 64

MartisDXX

N x 64+ 8 + 8

SB

Yes

Yes N ≤ 8

N x 64

MartisDXX

N x 64+ 8 + 8

SB

Yes

No N > 8

N x 64

MartisDXX

N x 64+ 24

SB

Yes

Yes N > 8

24V.110/7b refers to CCITT Rec. V.110 Frame Table 7b, and V.110M/7c is a slightly modified V.110 frame. MartisDXX is a V.110 (56 kbit/s) like Martis specific frame. 8, 16 denotes extra capacity carrying CRC with plesiochronous timing control. SA, SB and X refer to SA, SB, X bits in the frame.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 47

3 Operation

Rate kbit/s

Adaptation Method24

XB Mapping kbit/s

Control Signals

CRC

Plesiochronous Clocking

1544

-

N x 64+8

-

No

No

1544

MartisDXX

N x 64+8+ 8 + 8

SB

Yes

No

1544

MartisDXX

N x 64+8+ 24

SB

Yes

Yes

At all data rates the channels can simulated carrier in accordance with V.13 for transfer of the 105/109 signal. V.13 is mostly used at rates n x 64 kbit/s.

3.6.5

Cross-Connection of Unframed Interfaces The cross-connection ports are defined by using interface definition, TS definition, and a possible bit mask (n x 8 kbit/s connections). In some cases an unframed interface can be defined only by using the interface definition (in Tellabs 8000 manager only). The first time slot of a port definition of an unframed interface is always TS0. The bit mask means a combination of 8 bits where state 1 indicates an 8 kbit/s channel of a time slot which is connected; state 0 means capacity left free. The mask can also be presented in hexadecimal format. The entire capacity of the unframed interface must be connected in order to ensure the proper function of the interface. The unframed interface can be provided with a control channel in some cases. Then the control channel must be connected as well. Many interface types can produce n x 8 kbit/s capacity even when the data speed in the interface is n x 64 kbit/s. For example, an unframed n x 64 kbit/s connection with end-to-end CRC checking needs 8 kbit/s additional capacity in the XB channel. When the XB capacity of the unframed interface is exactly n x 64 kbit/s, the n x 8 kbit/s cross-connection is not needed. 48…56 kbit/s data interfaces after V.110 rate adaptation, for example, need 64 kbit/s XB capacity. All low rate data interfaces (≤19.2 kbit/s) need n x 8 kbit/s cross-connection. When making connection to the unframed interface which has such control bits as CRC checking, the control bits are the last bits of the port. If the data uses the whole n x 64 kbit/s capacity (whole time slots), the control bits are the lowest bits of the next time slot. When the unframed interface is connected to the framed interface and a part of the full capacity consists of n x 8 kbit/s portions, a bit mask must be used for the connection of the n x 8 kbit/s portion. The control bits can be connected to any usable time slot and bit in the framed interface.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 48

22030_12 © 2013 Tellabs.

3 Operation

Fig. 20 Example of Cross-Connection

The figure above shows an unframed interface IF3 with a bit rate of 144 kbit/s and control channel with 2 x 8 kbit/s (in all 160 kbit/s) connected to a framed interface IF1 which has the G.704 frame structure. The unframed port is specified as capacity 2 x 64 kbit/s and 4 x 8 kbit/s, which means two time slots and four bits. The first time slot of the unframed interface is TS0. TS0 and TS1 of interface IF3 are connected to TS2 and TS3 of IF1. This can be made with the TS pair or TS area commands. In the TS pair command one time slot from both interfaces is defined, and the cross-connection is created between these time slots. In the TS area command the first and the last time slot of an area with equal amount of time slots in both interfaces are defined, and the cross-connection is made between these areas. The last four bits of the unframed interface (two payload bits and two control bits) in TS2 are connected to the TS4 of the framed interface with the TS bits command. In the TS bits command the time slot and the bit mask for both the interfaces are defined, and the cross-connection is made between the unmasked bits. The control bits are automatically connected when the Connect whole port command in Tellabs 8000 manager is used.

3.7

Test Resources Tellabs 8120 mini node M has many functions to indicate a defect in the operation of the equipment or in the data transmission. Some tests are performed when the power is switched on, some of them are running as background processes, and some of them are activated by the . In the following chapters the tests are grouped to equipment tests, like the control of the voltages of the power supply, and to interface tests, by which the quality of data transmission can be controlled and the failure localisation in fault conditions can be performed. The type of the -activated tests depends on the interface. Usually, tests can only be activated through the service computer or the Tellabs 8000 manager network management system. In Tellabs 8120 mini node M, however, some tests can be activated through the front interface. If the equipment is connected to Tellabs 8000 manager, it is possible to activate the test resources for the specified circuits in the desired place in the network.

3.7.1

Equipment Test When the equipment is restarted after a reset, some start-up tests are executed. For instance, the correct starting of the main oscillator and the condition of the cross-connect RAM memory is checked. The equipment is not allowed to start other processes if these things are not in order.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 49

3 Operation

When the equipment is running, many tests are executed as background processes. The uP memory test and the data buffer test are checking the condition of certain components of the equipment. The uP memory test checks the EPROM, RAM and flash memories, and the data buffer test checks the Tx-ram and the Rx-ram memories of the framed interfaces. The tests run continuously. The results can be read with the service computer. A detected fault situation causes an alarm. The reason for the alarm can be traced using the interface, or a service computer, if available. The equipment has capability to measure the voltages generated by the main power unit. The measurement process runs continuously and the results can be read using the service computer. Values that are too low will cause an alarm. The cross-connect bus test is also running as a background process for locked interfaces. This test checks the cross-connect data busses and some parts of the ASIC circuits. A failure of the test causes the IA Missing alarm for the failed interface.

3.7.2

Test of Framed Interfaces

G.821 Statistics To control the quality of the data transmission of the framed interfaces, the signal statistic values according to the ITU-T G.821 Specification are ed in both framed interfaces separately. Near-end and far-end statistics: • total time (seconds) • unavailable time (seconds) • errored seconds • severely errored seconds (10 -3) • degraded minutes (10 -6) Error Counters The number of the following events can be read and cleared by the interface in both framed interfaces separately in order to check the reason for poor quality, or to search the fault of the transmission line: • code errors • number of G.704 frame losses • number of frame synchronization word errors • number of CRC block errors • buffer slips The count time of the counters is from the last reset of the counters or from the last reset of the equipment. In some cases all the values are not available; for example, the V.35 interface does not use coding in the transmission, and for this reason the code errors are not counted.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 50

22030_12 © 2013 Tellabs.

3 Operation

Test Loop Functions The loops and measurement points are used to find a faulty section of the line and to detect the faulty transmit or receive direction. When the framed interface is looped, all data circuits going through the interface are looped. The equipment includes a loop time-out control which will turn off a loop when the time defined by the has come to an end.

Fig. 21 Loops of a Framed Interface

Interface Loop The following signals are activated during the interface loop. • Tx data of the interface module is looped back to the receiver of the interface. • Tx clock is looped to the Rx clock. • AIS is transmitted to the line. • Looped data is connected back to the demultiplexer. The type of the module determines the point where the loop is created in the module. In most cases, due to technical reasons, the loop is not made by using a signal with line level. The loop will, however, always test the control bus of the interface module, the connectors, and a part of the module logic. The line coder and decoder, as well as the frame multiplexer and demultiplexer, are also tested in the loop. There should be no other faults in the unit fault list when the loop is created. Equipment Loop The following signals are activated during the equipment loop. 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 51

3 Operation

• Tx data from the G.704 multiplexer (before the interface module) is looped back to the demultiplexer. • AIS is transmitted to the line. • Looped data is connected back to the frame demultiplexer. The equipment loop is made in the unit. This loop tests the frame multiplexer and demultiplexer. Neither the line coder, the decoder nor the interface module are included in the loop. It is also possible to detect faults in the transmitting and receiving buffers. If no problems are detected with the equipment loop, it is suggested that the perform a test with the interface loop to ensure that the module is in order. Line Loop The following signals are activated during the line loop. • Rx data, received by the interface module, is looped back to the interface output. • The received clock signal is used as the transmitter clock. • AIS signal is connected to the X-bus instead of the received signal. The interface module, the line coder, and the decoder, as well as the frame demultiplexer and the multiplexer, can be tested from the line connector of the module with the line loop test. When it is used, the HDLC controller works with the line loop. All other bits are looped back to the interface. Remote Line Loop The remote line loop operates in the looped unit in the same way as the local line loop. The remote line loop is activated from the unit at the other end of the line. The loop is made via the HDLC channel, and the control channel will continue to operate even when the remote line loop is active. The status of the looped unit can be checked with the interface. When the loop is made, the yellow LED of the unit controlling the loop is switched on, and the yellow LED of the looped interface is also lit. The whole line can be tested with the remote line loop. Measuring Point A 75 Ω G.703 type coaxial cable measuring point is provided on the back of the unit. The measuring point is isolated with a transformer, but the connector body is connected to the unit ground. Through the measuring point it is possible to measure the input and output signals of both framed interfaces IF1 and IF2, as well as the corresponding clocks. The choices are • Rx data after the interface module but before the frame demultiplexer • Rx clock • Tx data after the frame multiplexer but before the interface module • Tx clock The signal to be measured is selected with the service computer in the General Unit Parameters window. The selection can also be made with the front interface in Tellabs 8120 mini node M. This selection is stored in the non-volatile memory of the unit so that the selection is also retained after a possible power interruption.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 52

22030_12 © 2013 Tellabs.

3 Operation

The data signal of the measurement point is HDB3 coded and independent of the type of the interface module and the coding of the data interface signal. The signal levels and formats are in accordance with G.703. The loops and the measurement point can be used to detect a faulty Tx and Rx direction and to pinpoint a faulty line.

3.7.3

Tests of Unframed Interfaces

G.821 Statistics Every unframed interface has its own group of counters when the V.110, X.30 or the Martis framing is activated with the CRC transfer. The available circuit performance values are • total time (seconds) • unavailable time (seconds) • errored seconds • severely errored seconds • degraded minutes With these values the quality of the data transmission can be controlled in accordance with the CCITT G.821. The values can be read and cleared with the interface separately. Error Counters The channel board can count the following event numbers by using the software and the hardware counters. These event numbers can be read and cleared by interface, each interface separately: • number of V.110 frame losses (the frame from the net) (the frame of XB channel) • number of multiframe losses (the frame from the net) • number of frame word errors (the frame from the net) • number of CRC block errors • code errors in the interface (G.703, start-stop format) • buffer slips and adjustments Test Loop Functions To find the places where problems might occur in the unframed interfaces, there are test loop functions which can be activated separately for each interface with the service computer or with the front interface. All loops have a separate time-out counter which is adjustable by the . The counter deactivates the loop when the set time has expired. The V.54 loops ed by the equipment can be limited or even disabled with the interface. The V.54 loops also have special configurable values, adjustable to seconds, which will turn off a loop when the defined time has come to an end. A loop activated to an unframed interface only affects the data circuit which goes through the involved circuit.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 53

3 Operation

Fig. 22 Loops of Unframed Interface

Interface Loop The following signals are activated during the interface loop: • The Tx data of the interface module is looped back to the receiver of the interface. • The Tx clock is looped to the Rx clock. • The looped signal is connected back to the cross-connection. The operator can activate an interface loop which is close to the physical interface back towards the network. When this loop is activated, it is possible to test the correct function and cross-connection of the unframed interface by connecting measuring equipment to the framed interface to where the looped interface is cross-connected, or by connecting the data measuring equipment to the remote end of the circuit. Line Loop The following signals are activated during the line loop: • Rx data, received by the interface module, is looped back to the interface output. • AIS signal is connected to the X-bus, instead of the received signal. A line loop can be activated close to the X-bus interface towards the interface. If some of the framing formats are used, the frame multiplexer and demultiplexer, as well as the CRC circuit, are included in the loop. By activating the line loop it is possible to test the whole interface from the line connector of the module.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 54

22030_12 © 2013 Tellabs.

3 Operation

Local Loop and Remote Loop The unframed interfaces are equipped with the V.54 test loop functions ing the local loop (loop 3, LL) and the remote loop (loop 2, RL). The X.21 loop functions (LL, RL, RLB) are ed by the X.21 interface module. The loops can be controlled with the interface, or the loops can also be controlled with the device through the signals 140 and 141. For these loops the interface has configurable parameters to disable, enable, enable with timer, or only allow the operator to control the loops. All the loops have an adjustable enable timer. In general, the loops should be enabled in the equipment which are as close as possible to the interfaces, and disabled in all intermediate equipment. The local loop can be activated with the interface or by activating the input signal 141. Activating the local loop makes it possible to check the operation of the interface and the line from the device. The remote loop is activated when the V.54 loop circuit receiver recognizes the activation pattern coming from the far-end through the X-bus. The sending of the pattern from the far-end is activated by the interface or by the input signal 141. The remote loop makes it possible to check the whole data circuit through the network. One way to perform this is to use the built-in test pattern generator and pattern error detector of the unframed interface. There is one test pattern generator per interface. When some of the V.54 loops are on, the test loop indication signal 142 goes on. Thereafter, the loop tests can be started. A loop 2 (RLB) activated from the far-end turns the signal 142 on and sets the received data to off. In case of X.21, loop 2 activated at the far-end sets the received data to off or to pattern 1010…. Test Pattern Generator The channel module has built-in per channel test pattern generators and pattern error detectors. The test pattern is according to the ITU-T Recommendation O.151. Typically, a test is performed with the remote loop activated at the far-end. The interface facilitates the activation of the test resources and presentation of the test results.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 55

4 Installation

4 Installation 4.1

Front Indicators and Controls The front of Tellabs 8120 mini node M is presented in Fig. 23.

Fig. 23 Front of Tellabs 8120 Mini Node M

The four buttons and the LCD display are for local control operations. The front of Tellabs 8120 mini node M is equipped with LEDs to display the alarms of the system and the interface circuits. There are two alarm LEDs (red and yellow) for each block; IF1…IF6 and SYS. Each block reports its own alarms with these LEDs. For the service computer (SC) there is a 9.6 kbit/s asynchronous V.24 interface with a 9-pin D connector.

4.2

Back Connections Fig. 24 shows a typical back arrangement of Tellabs 8120 mini node M. The fixed items of the back are a power connector, a measurement connector, and the synchronization connectors. The back is furnished with four different changeable interface modules. The type of the connector depends on the type of the module. The numbering of the interfaces is also shown in the figure below.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 56

22030_12 © 2013 Tellabs.

4 Installation

Fig. 24 Tellabs 8120 Mini Node M with BTE-384M, G703-75-M, V35-M and V36-M Modules

There are two places for unframed interface modules on the upper part of the . In one unframed module there are two channels with the same type of an interface. Each module can be of a different type, and there are no restrictions to usage of different types of unframed modules in the same piece of equipment. On the lower part of the back there are two places for framed interface modules. On the framed interface modules there is one interface in each module. Also the framed interfaces can be of a different type in the same piece of equipment. The synchronization connectors provide a 75 Ω input and output for the clock signal of the master clock oscillator of the equipment. Through these connectors the equipment can be synchronized to an external clock source, or the equipment can give a clock to another data transmission equipment connected to the same transmission network. The control of the clock signal is handled with the Master Clock menu of the interface. The interface signals and the Rx and Tx clocks of the framed interfaces can be measured with measurement equipment through the measurement connector. The impedance of the interface is 75 Ω. The back arrangement for Tellabs 8120 mini node M with a different module configuration is shown in Fig. 25.

Fig. 25 Example of Back with G703-75-M, OTE-LED-M, V36-M and V35-M Modules 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 57

4 Installation

If an unframed interface module ( access interface module) is removed permanently by the , it must be replaced with a blank upper interface, part code 880070157A, to close the back opening.

If a framed interface module is removed permanently by the , it must be replaced with a blank lower interface, part code 880070158A, to close the back opening.

4.3

Mains Connection Tellabs 8120 mini node M is connected to a 100…240 V AC mains supply with a three-pin grounded plug. The maximum power consumption is approximately 40 V A. The consumption varies depending on the installed module configuration and the bit rates in use. Other power supply alternatives are a 48 V DC or a 24 V DC power supply. Tellabs 8120 mini node M is equipped with one primary fuse. If the green power indicator is switched off, it indicates a failure of the fuse. Other power supply problems can be checked with the interface which has a voltage measurement facility. The fuse of the AC model is located inside the metallic case. Only qualified personnel is allowed to change the fuse.

Tellabs 8120 mini node M must be disconnected from the mains supply before removing the cover as high voltages are present inside the case.

The AC model mains supply primary fuse can be changed after the metallic top cover and power supply shield have been removed. The primary fuse of the DC models is accessible on the back of the device. The fuse is of a standard 5 x 20 mm size and it must be replaced with the ratings indicated below. Power Unit 8990NFS40 PDU422 24 V

DC25

PDU423 48 V DC

Fuse

Input Voltage

T1A

100…240 V AC ±10% 47…63 Hz

T4A

19…36 V DC, negative pole earthed

T4A

40…60 V DC, positive pole earthed

Power consumption: 40 V A max.

4.4

Operating Environment When installing Tellabs 8120 mini node M, do not put it in a warm place.

25The

power supply module PDU422 has been discontinued.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 58

22030_12 © 2013 Tellabs.

4 Installation

Never put Tellabs 8120 mini node M on top of another piece of equipment of the same kind because it can cause overheating and malfunctioning of the equipment. A very dusty or humid installing place can also cause incorrect working of Tellabs 8120 mini node M and, in some cases, even danger for the .

Operating temperature: +5…+35 °C Operating humidity: < 85% RH, non-condensing The figure below shows how the ventilation air goes through the device. Enough free space should be left around Tellabs 8120 mini node M to guarantee proper functioning and ventilation.

Fig. 26 Route of Ventilation Air

Do not cover the ventilation holes on the case of Tellabs 8120 mini node.

4.4.1

DC Power Supply Cabling Tellabs 8120 mini node M with DC power supply is connected to the main battery system with a two-wire cable which has the following color codes:

22030_12 © 2013 Tellabs.

24 V DC Power Supply

Wire Color

+24 V

Red

0V

Black

48 V DC Power Supply

Wire Color

-48 V

Blue

0V

Black

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 59

4 Installation

4.4.2

SC, Local Service Computer Connector The SC, local service computer connector is provided with a 9-pin female D-connector according to ISO 2110 Standard. The connector is furnished with two UNC 4-40 locking screws.

4.4.3

Pin #

ITU-T Circuit #

Signal Level

Function

1

109

V.28

Received line signal indicator

2

104

V.28

Received data

3

103

V.28

Transmitted data

4

108

V.28

Data terminal ready

5

102

-

Signal ground

6

107

V.28

Data set ready

7

105

V.28

Request to send

8

106

V.28

Clear to send

9

-

-

Not connected

SYNC Connector The SYNC connectors are SMB type connectors, electrically of G.703/75 Ω impedance.

4.5

Configuration of Tellabs 8120 Mini Node M Step 1

Check that Tellabs 8120 mini node M is ready for operation: • Interface modules are properly installed and fastened. • The cover is installed. • The metallic case is in its place and fastened with all screws. • No loose parts are inside the case.

Step 2

Put Tellabs 8120 mini node M to correct operation environment as described in 4.4 Operating Environment. • Check that nothing covers the ventilation holes of Tellabs 8120 mini node M. • Note that there are ventilation holes also on the sides of the metallic case.

Step 3

Connect interface connectors to the back of Tellabs 8120 mini node M.

Step 4

Connect the power cord to the main power supply and the protective earth wire to the grounding terminal. See the exact location of the wire in Fig. 40. • Screw the grounding earth wire with washers tightly to the M5 nut at the back of the node.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 60

22030_12 © 2013 Tellabs.

4 Installation

When DC power supply is used, Tellabs 8120 mini node M must be permanently connected to earth using the supplied grounding earth wire.

Fig. 27 Grounding Earth Wire Assembly

Step 5

Tellabs 8120 mini node M is now ready for use. • Check that no unusual alarms are on.

Step 6

Configure Tellabs 8120 mini node M with planned parameters. • Check that the parameters for the framed interfaces and master clock are correct. (See 4.7 Recommended Settings of Framed Interfaces for recommended settings.) • Set the node ID. When the power cord is connected, the green and yellow LEDs are lit. After a start-up time, which is from 30 to 60 seconds and depends on the configuration of the equipment, the yellow LED will be switched off and Tellabs 8120 mini node M is ready for operation. The meaning of the color of LEDs is explained below. Green

Lit when Tellabs 8120 mini node M is connected to the mains supply and the power is switched on.

Yellow

Lit when Tellabs 8120 mini node M is receiving alarm indication from the network (far-end alarm, AIS). Test state (loops etc.).

Red

All other fault situations.

The configuration of Tellabs 8120 mini node M can be monitored and altered through Tellabs 8000 manager or by a local service computer connected to the front connector, a 9.6 kbit/s asynchronous V.24 interface. There are two HDLC control channels (one in both framed interfaces IF1 and IF2). These are normally used when Tellabs 8120 mini node M is connected to Tellabs 8000 manager. The control functions operate as in a Tellabs 8100 cross-connect node. The Tellabs 8120 mini node M blocks have the same Tellabs 8000 manager functions as in the corresponding units in the Tellabs 8100 node. The common test resource, which is in the SCU unit of the other nodes, does not, however, exist in Tellabs 8120 mini node M. The configuration can also be done locally through the front keys and the LCD display. It can be monitored on the LCD display during operation without interfering with data transmission.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 61

4 Installation

4.5.1

NMS Control Tellabs 8120 mini node M is designed to be controlled by Tellabs 8000 manager. The control functions operate as in a Tellabs 8100 cross-connect node. There are two HDLC control channels (one in both framed interfaces IF1 and IF2). These control channels are used when Tellabs 8120 mini node M is connected to Tellabs 8000 manager. There is a 9.6 kbit/s asynchronous V.24 interface on the front . Through this interface Tellabs 8120 mini node M can be controlled also with the service computer of the Tellabs 8100 system. The Tellabs 8120 mini node M blocks have the same NMS functions as the corresponding units in the Tellabs 8100 node. The common test resource, which is in the SCU unit of the other nodes, does not, however, exist in Tellabs 8120 mini node M.

4.5.2

Local Control Tellabs 8120 mini node M has a local keyboard (four buttons) and an LCD display for local control operations. With these tools the local can make the same operations that are possible with the service computer connected to the SC interface on the front . With the local keyboard and the LCD display the can perform the following operations: • read the node parameters • node ID • unit ID (hardware and software versions, serial number) • read/set master clock parameters • creating and deleting cross-connections (not possible with SC) • alarm information from each interface and block • read the active faults or the fault history • clear the fault history • set interface tests and loops • read the error counters and G.821 error statistics from each interface • read the status of V interface control signals • read/set interface parameters In the following description the abbreviation NTUM refers to Tellabs 8120 mini node M. The NTUM parameter settings can be monitored during operation through the display without interfering the normal data transmission. The parameter settings are stored in a non-volatile memory. The Configuration menu recognizes the interface units and transmission modules and displays the correct menu items accordingly.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 62

22030_12 © 2013 Tellabs.

4 Installation

The LCD display has two lines with 24 characters each. In most cases three item fields are shown at a time. The upper line is used to show the heading of an item; on the lower line there is the value of the item or the text DIR, which means that there is a sub-menu for the item. Although there are three items on the display, there may be many other items at the same level of the menu. The other items can be scrolled to the display with the keys. The blinking cursor indicates the current item field. When the cursor is on the upper line, the SCROLL keys (< or >) are used to move from one item to another at the same menu level. When the cursor is on the lower line, the SCROLL keys are used to change the value of the parameter of the item. By using the EXIT and ENTER keys the can move up or down in the menu structure. The ENTER key is also used to confirm a selection from a menu. When the cursor is on the upper line, the EXIT key causes a move upwards to the next menu level. On the lower line the EXIT key moves the cursor from the value field to the heading of the item. The ENTER key moves the cursor from the heading to the value field of the item or to the sub-menu if the value is DIR. When the cursor is on the value field, the use of the ENTER key confirms that the present value of the field is used as a new value of the item and the cursor moves to the heading of the item. If the value of an item is changed, the new value of the menu branch must be confirmed by the Update field, which is the first field of the branch. The value of an item is changed in the following way. Step 1

Move the cursor with the SCROLL and ENTER keys to the heading of the item you want to change.

Step 2

Press the ENTER key to move the cursor to the value field.

Step 3

Use the SCROLL keys to select the new value for the item.

Step 4

Press the ENTER key to confirm the new value.

Step 5

Use the SCROLL keys to move the cursor to the Update field of the present menu branch.

Step 6

Press the ENTER key to move the cursor to the value field of the Update field.

Step 7

Press the ENTER key to confirm the update.

Step 8

The text Updating appears on the display. Do not push the keys before the text disappears and the menu text is visible. All the needed changes of a menu branch can be made before using the Update field. If the phase of the present menu level (menu, sub-menu or item) is unknown to the , the main level is reached by pressing the EXIT key several times.

4.6

Menus of Tellabs 8120 Mini Node M The following figures present the menu structure of Tellabs 8120 mini node M.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 63

4 Installation

Fig. 28 Main Menu of Tellabs 8120 Mini Node M

Fig. 29 Menu of Main Parameters Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 64

22030_12 © 2013 Tellabs.

4 Installation

Fig. 30 Main Interface Parameters Menu of IF1 and IF2

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 65

4 Installation

Fig. 31 Menu for IF1 and IF2 Parameters

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 66

22030_12 © 2013 Tellabs.

4 Installation

Fig. 32 Menu for Neighbour Node Message Parameters

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 67

4 Installation

Fig. 33 Cross-Connect Menu

4.6.1

Security Menu The security menu contains two items (device mode and locking) which can be set. This menu is entered in a specific way explained in 4.6.7 Entering Security Menu of Tellabs 8120 Mini Node M.

Device Mode Menu The Device Mode menu specifies the device mode of the NTUM. The NTUM can be either a MartisDXX device or a stand-alone device. The MartisDXX device is usually a part of the Tellabs 8100 network and it is managed by Tellabs 8000 manager. Therefore, you are not allowed to configure the cross-connections of the MartisDXX device by using the front keys and the LCD display. Neither are remote configuration and monitoring allowed when the NTUM is in the MartisDXX device mode. The text DXXNTUM indicates that the NTUM is in MartisDXX device mode. Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 68

22030_12 © 2013 Tellabs.

4 Installation

The text NTUM indicates that the NTUM is in the stand-alone mode. In this mode all the configuration and monitoring operations are allowed by the use of the front keys and the LCD display if the is unlocked. To change the device mode, use the SCROLL keys to select the new mode and press ENTER. When ENTER is pressed, the new mode is saved into the non-volatile memory to make sure that the NTUM will go to the correct mode after reset. Menu The item for key locking has three settings ( unlocked, locked, configuration locked) to prevent the from accidentally selecting the wrong settings to the configuration items and thus making the NTUM non-functional. To make any changes to the NTUM configuration, the item for the key locking has to be unlocked. The items for locking and their features are • locked, Locked • NTUM configuration cannot be seen nor altered • Some statistics are available to the • configuration locked, Cfg. Lock • NTUM configuration can be seen but not altered • unlocked, Unlocked • NTUM configuration can be seen and altered • Menus are available to the according to the device mode To change the mode, use the SCROLL keys to select the new mode and press ENTER. When the ENTER is pressed, the new mode is saved into the non-volatile memory to make sure that the NTUM will go to the correct mode after reset.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 69

4 Installation

Fig. 34 Device Modes of Tellabs 8120 Mini Node M

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 70

22030_12 © 2013 Tellabs.

4 Installation

NTUM Menu The NTUM interface can be used to configure a local or a remote NTUM. The local NTUM is the target by default. The remote NTUM that is connected to the local NTUM via a trunk interface (IF1 or IF2) can be configured by using the local interface if the HDLC communication channel is established over the trunk. To set the target NTUM, use the SCROLL keys to select it and press ENTER. Choices for the target NTUM are Local, Remote1 and Remote2. The number after the text Remote specifies the trunk interface that is used. The yellow LED of the corresponding interface blinks on the front of the local NTUM when it is in remote mode. The remote configuration is not allowed if the NTUM is part of the Tellabs 8100 network.

4.6.2

Faults Menu Three menu branches are available from the field of Faults by pressing the ENTER key: ActFlts, FltHist and ClrHist. From these fields the can see the fault(s) which are active at the moment or receive the information of the latest fault state transitions (the fault history report) and clear the history report.

ActFlts The ActFlts menu is used to ask active faults from the target NTUM by pressing the ENTER key. The active faults can be seen in the following list format (fault/interface or common level fault). 1

Rx signal mis.

IF 1

2

Master clock flt

Com

3

Fr fe alarm

IF 2

4

AIS from X-bus

IF 5

If there are several faults, two of them will be displayed and the rest of the faults can be viewed by using the SCROLL keys. Pressing the ENTER key activates a new fault query from the NTUM. FltHist From the FltHist menu the can see the fault history report by pressing the ENTER key. The fault history is useful when a fault has been on (the red LED flashes) but when asking for active faults the response is No faults. The display format is:

22030_12 © 2013 Tellabs.

1

Reset

Com

DLT

2

Master clock

Com

ON

3

Rx signal mi

IF 1

ON

4

Fr f-e alarm

IF 2

ON

5

Fr f-e alarm

IF 2

OFF

6

Rx signal mi

IF 1

OFF

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 71

4 Installation

If there are several faults on the history report, two of them will be displayed and the rest of the faults can be viewed by using the SCROLL keys. The latest fault transition has the biggest number (in the case above 6 Rx signal mi IF1 OFF is the latest fault transition). Pressing the ENTER key activates a new fault query from the NTUM. ClrHist The fault history can be cleared in the ClrHist menu by pressing the ENTER key. After clearing the faults the unit starts the fault history collection automatically.

4.6.3

Parameters Menu The general node and unit level parameters can be read and changed in the branch Param. (all parameters, e.g. the serial number, are not changeable). The readable and changeable parameters are the node and unit level identification data, the cross-connection clock selection (MastClk), the module defining, the 1+1 protection and the measurement point selection.

Node Identification Menu The NTUM has its own node identification number 0…65535 which can be changed by the . Each node in the network must have a different Node ID. Unit Identification Menu Only the unit level information of the NTUM can be read in this branch. Hw-ver

The hardware version of the unit.

Sw-ver

The software version of the unit is used to identify the ed software version etc.

Year

The year when the unit was manufactured.

Week

The week when the unit was manufactured.

Serial

The serial number which is an absolute identification of the unit. The serial number is set at the production phase of the unit.

Master Clock Menu The NTUM has a 16-MHz master clock which is used for generating the timing of the cross-connect bus. The timing consists of • 16 MHz • 8 kHz frame sync • 500 Hz multiframe sync The interfaces use these signals in the bus interface. The 16-MHz clock is also used to generate the Tx clock of each data interface. The master clock is usually synchronized to one of the incoming data signals (generally a 2 Mbit/s trunk). The clock of the desired interface is collected by using a separate synchronization clock bus (SYB). The master clock object tells the required interface to connect its Rx clock to this bus.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 72

22030_12 © 2013 Tellabs.

4 Installation

The clock fallback list is used to define the synchronization priority order. The list can have up to five entries. The form of the clock fallback list is 1.

IF_

2.

IF_

3.

IF_

4.

IF_

5.

Ext. clock (Internal)

The list can also be made shorter. The last entry is followed automatically by the internal state. On the back of the NTUM there is a connector for the external clock input. It can be selected to the clock fallback list. The frequency of the external clock can be defined as n x 64 kHz, where n = 1…132 (64 kHz…8448 kHz). The NTUM also has a clock output. It is electrically similar to the clock input. The clock output frequency is derived from the master clock and its frequency can be selected (n x 64 kHz). Usually 2048 kHz is used. The master clock of an NTUM can be configured and monitored by using the master clock menu. The master clock menu is entered by pressing the ENTER key when the cursor blinks on the MastClk text. The Master Clock menu contains the following fields (upper line).

22030_12 © 2013 Tellabs.

Update

This field updates the new master clock parameters to the target NTUM (local or remote).

Choices

All the available interfaces that can be used as the master clock are displayed here. If there are no available interfaces, the text None is shown. The text Ext refers to the external clock. The list of the available interfaces can be scanned by using the SCROLL keys. To add an interface in the fallback list, press ENTER when the cursor blinks on that interface. The text Add IFn in 1st FBL slot is shown. Use the SCROLL keys to change the slot number. When the slot number of the fallback list is selected, press ENTER to add the interface in the fallback list.

FB List

The fallback list of the master clock is displayed in this field. The elements of the list are in the priority:source format. The text None indicates that the list is empty. The fallback list can be scanned by using the SCROLL keys. To remove an interface from the fallback list, press ENTER when the cursor blinks on that interface. The text Remove IFn from FB List is shown. Press ENTER again to remove the interface, otherwise press EXIT.

State

This is the sub-menu for the state monitoring of the master clock. Press ENTER to start the state monitoring. The State Monitoring sub-menu contains the following fields which are automatically updated every fifth second.

Source

This field indicates the current source of the master clock: Intern, SYB1, SYB2 or Extern.

State

This field indicates the current state of the master clock: OK, Alarm.

SYB1/2

This field displays the source interfaces of the sync clock busses.

Ext Clk

This field specifies the frequency of the external clock. To change the frequency, use the SCROLL keys to select a new frequency and press ENTER.

Clk Out

This field specifies the frequency of the clock output. To change the frequency, use the SCROLL keys to select a new frequency and press ENTER.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 73

4 Installation

OutCtrl

This field specifies the control mode of the clock output. The output clock controlling is either ON or OFF. If the output clock controlling is ON and the output clock is enabled (an output clock frequency is specified), the output clock will be disabled if the source of the master clock is either an internal or an external clock. If the output clock controlling is OFF, the state of the output clock does not depend on the source of the master clock. To change the control mode, use the SCROLL keys to select a new mode and press ENTER.

ATime

This field specifies the acceptance time for the clock sources. A clock source is a valid source for the master clock if the status of the clock source has been OK for at least as long as the acceptance time specifies. The acceptance time value is 0-120 s. To change the acceptance time, use the SCROLL keys to select a new time and press ENTER.

Module Configuration Menu The NTUM device has six interfaces and four independent interface modules. The modules are numbered so that the modules 1 and 2 have corresponding interfaces (1 and 2), but modules 3 and 4 have both two interfaces (3, 4 and 5, 6). When the has decided to install a new interface module, also the module configuration must be changed from the Config branch. IF1 Install

This field shows the currently installed module (read-only information).

Type

This field appears only if the installed module contains strappings. The field shows the information on module strapping (75 Ω/120 Ω/ contradirectional/codirectional).

Config

The module configuration field defines what kind of a module the unit program currently services. Thus, there should be the same module in the Install field as in the Config field. There is also a Not def selection which means that the interface has not been defined (module not in use) and no faults which belong to this module will be reported. If, for example, a module is not installed, the module should be configured as Not def.

1+1 Protection Menu The interfaces 1 and 2 can be configured into the 1+1 protected mode. In the protected mode both interface modules must the selected bit rate. The Rx signal faults are classified into several categories. The switch uses fault categories to select the interface to be used. When the IF1 or IF2 parameters are updated in the protected mode, both interface parameters will be updated (except for the baseband parameters Line, Level, ScrmTyp, ScrmMo, 10E-3 Consequences, FltMsk and Configured Module). Update

This field is used to update the 1+1 protection parameters in the NTUM. The 1+1 parameters (Mode, HomeSta, ChaDel and Force) can be changed on other fields but after the changes the parameters must be updated by pressing the ENTER key in the Update field.

Mode

In this field the 1+1 mode can be defined on/off. The No prot selection means normal unprotected mode, ProtIf1 means protected mode by settings of interface 1, and ProtIf2 protected mode by settings of interface 2.

CurSele

The field is displayed only in the 1+1 protected mode; it shows which Rx signal is connected to the cross-connection. The field is auto-refreshed.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 74

22030_12 © 2013 Tellabs.

4 Installation

HomeSta

This field is displayed only in the 1+1 protected mode. The home state can be changed in the field to the switch which selects the Rx signal. The selection No H-S means that the switch chooses the better Rx signal and the selection changes will be made only when the unused Rx signal quality is better than the used Rx signal. The selection IF1/IF2 means that the IF1 or IF2 interface is defined as the home state, and when both interfaces are classified to the same category, the switch selection returns always back to the home state interface.

ChaDely

This field is displayed only in the 1+1 protected mode. The field handles the protection switch change delay (0 ms…10 min). The change delay is a filter parameter of the protection switch so that the fault transition which can affect the switch turning must be active for the duration of the change delay before the switch turns.

Force

This field is displayed only in the 1+1 protected mode. The field handles the force control of the protection switch. The state None is normal; in the state IF1 or IF2 the protection switch is forced to select IF1 or IF2. The time-out for this control is the same as the time-out for IF1 controls.

Measurement Point Menu The NTUM device has one measurement point. The signal can be selected to this point from interfaces 1 or 2 and the signal can be either Rx clock or data or Tx clock or data. MeasPnt

4.6.4

The measurement point selections can be scanned by using the SCROLL keys. Press the ENTER key to confirm the selection.

Interface Parameters Menu The interface parameters (interface 1…6) can be read and changed in this branch. The reading/change possibility depends on the state (see 4.6.1 Security Menu). Interfaces can be divided into two groups according to their sub-menus: interfaces 1…2 have the same type of sub-menus, whereas the sub-menus of interfaces 3…6 are similar. Parameters of Interface 1 and 2 The following menus are available when the selected interface is IF1 or IF2.

22030_12 © 2013 Tellabs.

Param

The general interface parameters can be read, changed and updated in this branch.

Update

This field is used to update the interface parameters. The interface parameters (Framing, Rate, Basband, BitUse, CAS, CntrlTyp, Buffer, FtsData, FltMsk, FltAct) can be changed in other fields and sub-menus but after changes the parameters must be updated by pressing the ENTER key in the Update field.

Framing

The possible selections are On, Off RxM, Off. All selections are available when the interface is in unlocked state. If the state is locked, the changes can be made only between Off RxMon/ Off.

Rate

The selectable bit rate depends on the configured module (the module must the selected bit rate). If the device is in 1+1 protected mode, both interfaces must the selected bit rate. When the framing is on, the minimum bit rate is 128 kbit/s (2 x 64k). If the interface is locked, no bit rate changes can be made.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 75

4 Installation

Basband

This field is displayed when the configured interface module is a baseband module. There are three sub-menus under the Basband menu.

*Line

The type of the line can be 2-wire or 4-wire when the biphase coding is used (BTE384).

*Level

The possible output levels depend on the type of the BTE.

*ScrmTyp

With BTE384 the possible scrambler types are None, V32, V29, NDPN and NPDNV29; with other BTEs None and V29.

*ScrmMo

The field is displayed only when the configured module is BTE384 and the possible scrambler modes are call and answer.

*WetCur

The field is displayed only when the configured module is BTE384 and the wetting current has the states ON/OFF. In the state ON, the BTE module detects when the NTU is in the POWER OFF state.

VdhScrm

This field is displayed when the configured interface module is V35-G704 or X21-G704. The scrambler has two states, ON/OFF.

BitUse

This field is displayed when the framing is ON and the sub-menus depend on the selected bit rate (in the 8M mode the sub-menus are different).

The following fields (TS0B1, CRCE, FSW/RAI, TS0B4…TS0B8) are displayed when the bit rate is not 8M. TS0B1

The field for selecting the use of TS0B1; one of the following: CRC use: CRC4 will be generated into this bit HDLC use: HDLC channel in this bit X-Con: the bit comes from the cross-connection CBSC: the bit is controlled by a separate command, e.g. in master clock remote alarm use 0: the bit will be transmitted at the permanent 0 state 1: the bit will be transmitted at the permanent 1 state. Note! When the control type is master or slave, this bit must be in CRC use.

CRCE

The field is displayed if TS0B1 is in the CRC state and the CRCE bit can be configured as:ReEnd: CRCE bit is used to indicate remote end CRC errors0: the bit will be transmitted at the permanent 0 state1: the bit will be transmitted at the permanent 1 state

FSW/RAI

The frame synchronization word and the far-end alarm (TS0B3) usage:Regen: Transmitted sync. word and remote-end alarm are regeneratedX-Con: Transmitted sync. word and remote-end alarm comes from the cross-connectionX-Sync: Sent frame is synchronized to the frame coming from the cross-connectionRAIXcon: Remote-end alarm comes from the cross-connection

TS0B4…8

Fields for selecting the use of TS0B4…TS0B8 are similar (but independent).HDLC use: the bit is selected for HDLC useX-Con: the bit comes from the cross-connectionCBSC: the bit is controlled by a separate command e.g. in master clock remote alarm use0: the bit will be transmitted at permanent 0 state1: the bit will be transmitted at permanent 1 state

The following fields (TS99B1-7, CRCE, TS99B8 and TS66B8) are displayed when the bit rate is 8M.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 76

22030_12 © 2013 Tellabs.

4 Installation

*TS99B1-7

The field for selecting the use of TS99B1-7.CRC use: CRC will be generated in these bitsHDLC use: bits are selected for HDLC useX-Con: bits come from the cross-connectionCBSC: bits are controlled by a separate command e.g. in master clock remote alarm use0: bits will be transmitted at the permanent 0 state1: bits will be transmitted at the permanent 1 state

*CRCE

The field is displayed if TS99B1-7 are configured for CRC use.ReEnd: CRCE bit is used to indicate remote-end CRC errors0: the bit will be transmitted at the permanent 0 state1: the bit will be transmitted at the permanent 1 state

*TS99B8

The field for selecting the use of TS99B8.HDLC use: the bit is selected for HDLC useX-Con: the bit comes from the cross-connectionCBSC: the bit is controlled by a separate command e.g. in master clock remote alarm use0: the bit will be transmitted at the permanent 0 state1: the bit will be transmitted at permanent 1 state

*TS66B8

The field for selecting the use of TS66B8.HDLC use: the bit is selected for HDLC useX-Con: the bit comes from the cross-connectionCBSC: the bit is controlled by a separate command e.g. in master clock remote alarm use0: the bit will be transmitted at the permanent 0 state1: the bit will be transmitted at the permanent 1 state

The HDLC and MCLRAI fields are both present whatever the bit rate is. *HDLC

The HDLC control channel usage is selected in this branch. When the HDLC channel is used in the time slots TS0, TS66 and TS99 or it is desired to be used there, the HDLC usage must be defined in the special time slot/bit field(s).

*HDLC

The following can be selected in this field:In use: the HDLC channel will be in use.-----: the HDLC channel is not in use.

*TS

When the HDLC channel is in use, the time slot for HDLC use can be selected in this field.

*Bit1…8

When the HDLC channel is in use, the bit(s) for HDLC use can be selected in these fields.

*MCLRAI

The master clock remote alarm usage can be controlled in this branch. The clock remote-end alarm can be configured into frame special bits or in data bits. Special bits must be configured as CBSC for the clock remote-end alarm usage. If the clock remote-end alarm is in the data bit, this time slot must not be cross-connected (MCLRAI usage reserves the whole time slot).MCLRAIIn use: MCLRAI will be in use.-----: MCLRAI is not in use.TS: When MCLRAI is in use, the time slot for MCLRAI use can be selected in this field.Bit1…8: When MCLRAI is in use, the can define in this field which bit of the time slot is in MCLRAI usage.Pol.: When MCLRAI is in use, the can define the polarity of alarm in this field.

CAS

This field is displayed when the framing is ON and sub-menus depend on the selected bit rate (in the 8M mode there are four CAS groups A, B, C and D; and in the other bit rate modes for signalling only one time slot is reserved).

The following fields (CAS, Bit5,7,8) are displayed when the bit rate is not 8M.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 77

4 Installation

*CAS

Use of channel associated signalling. When the bit rate is 1088 kbit/s (17 x 64 kbit/s) or higher, TS16 is used for signalling. In other cases the last time slot is used for signalling, e.g. if the rate is 384 kbit/s (6 x 64 kbit/s), the signalling will be in TS5:On: one time slot is reserved for signallingOff: signalling is not used and the signalling time slot can be in data use

*Bit 5,7,8

The fields are displayed if CAS is turned ON. There are three similar fields for selecting the usage of the special bits B5, B7, B8 of the signalling time slot.X-Con: the bit comes from the cross-connectionCBSC: the bit is controlled by a separate command e.g. in master clock remote alarm use0: the bit will be transmitted at the permanent 0 state1: the bit will be transmitted at the permanent 1 state

The following fields (CAS A, Bit5,7,8…CAS D, Bit5,7,8) are displayed when the bit rate is 8M. The fields for the signalling groups are similar. For this reason only the group CAS A is mentioned here. The time slots for the signalling groups are CAS A in TS67, CAS B in TS68, CAS C in TS69 and CAS D inTS 70. *CAS A

Use of channel associated signalling of group A (TS67).On: TS67 time slot is reserved for signallingOff: signalling is not used and the signalling time slot can be used for data use

*Bit 5,7,8

Use of the bits 5, 7, 8 is as above.

Buffer

The field is for handling the Rx buffer. The possible selections: 4, 8, 64 frame buffer. The selected bit rate and the split trunk usage affect the possible buffer length.

FtsData

The idle data of unconnected time slots can be defined in this branch. This means that the time slots which are not cross-connected are transmitted with idle data. It is recommended that all bits are set at the state 1.

*Bit1…8

There are eight similar fields (one field for each bit).1: the bit will be transmitted at the permanent 1 state.0: the bit will be transmitted at the permanent 0 state.

FltMsk

In this field the fault mask state (ON/OFF) can be handled. When the fault mask is ON, no interface faults will be generated (only the fault of the mask itself).

FltAct

Some fault actions and consequences can be defined in this branch. There are four sub-menus (AisInh, RaiInh, RaiCsq and E3Csq), each with two states ON/OFF.

*AisInh

The AIS inhibit ON affects the AIS alarm generating.OFF: the AIS alarm will be generatedON: when the received signal is AIS or in the received signalling TS is AIS, no alarms will be generated due to this fault.

*RaiInh

RAI inhibit ON affects the far-end remote alarm generating (from frame and multiframe level).OFF: the remote-end alarm(s) will be generatedON: when the received frame or multiframe far end alarm, no alarms will be generated due to this fault.

*RaiCsq

The remote alarm consequences affect to the AIS inserting into the received signalling time slot when the frame or the multiframe far-end alarm has been received.ON: AIS will be inserted when the far-end alarm has been received. The far-end alarm fault is provided with service alarm status (S).OFF: The far end alarm does not cause AIS inserting into the signalling time slot(s). The far-end alarm fault is generated without service alarm status.

*E3Csq

This field affects the AIS inserting into the received signal when the received signal error rate is worse than 10E-3.ON: AIS will be inserted into the received signal when the error rate is worse than 10E-3. The BER10E3 alarm will have the service alarm status (S).OFF: The error rate 10E3 does not cause the AIS insertion into the received signal. The BER10E3 alarm is generated without service alarm status.

AisDet

AIS detection in unframed mode ON/OFF:

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 78

22030_12 © 2013 Tellabs.

4 Installation

NnmPara

This branch handles the neighbor node parameters of the interface. When the interface framing is ON and the HDLC channel is in use, these parameters affect the sending and the monitoring of neighbor node parameters.

Update

This field is used to update the neighbor node parameters into the NTUM. The neighbor node parameters (Expected neighbour and Options) can be changed in other fields but after the changes the parameters must be updated by pressing the ENTER key in the Update field.

Alarms

This branch has two sub-menu fields Own and the Neighbour alarms (Loop, Unexpected neighbour, No connection, OK). The Alarm fields are auto-refreshed.

*Own

This is a read-only field where the neighbor node alarms of the target NTUM can be read.

*Far-end

This is a read-only field where the neighbor node alarms of the neighbor of the target NTUM can be read. The field is displayed only if there is a connection between the neighbors.

Exist

This branch has six sub-menu fields each of which has data of the existing neighbor (neighbor: node ID, subrack address, unit number, link number, interface number and port number). The fields are auto-refreshed.

Expec

The expected neighbor data has the same kind of data fields as in the Exist branch.

yExi

Copies the existing data structure to the expected field (you have to to update). This is useful when updating the correct neighbor info.

Options

This branch has three sub-menus to activate or deactivate the sending, the supervision and the monitoring.

*MesSend

ON: the neighbor node data sending activatedOFF: the neighbor node data sending deactivated

*StaMon

ON: the neighbor node state monitoring activatedOFF: the neighbor node state monitoring deactivated

*NeigSup

ON: the neighbor node supervision activatedOFF: the neighbor node supervision deactivated

Locking

This field is used to lock or unlock the interface. Locking means that the interface allocates the needed capacity from the cross-connection and unlocking that the interface deallocates the reserved cross-connection capacity. Please note that the text on the LCD display describes the next movement in the locking state if ENTER is pressed (e.g. if there is the text Lock, the interface is in the unlocked state and the next change is made to lock the interface).

Loops

The loop can be activated/deactivated and the state of the loops can be seen in this branch.

State

This is a read-only field where the loop state can be seen (e.g. Line Loop, Equipment Loop, Interface Loop, Remote Loop). The field is auto-refreshed.

Set

The loops can be activated/deactivated in this field. The Remote loop availability depends on the interface parameters (Framing, HDLC, NnmPara/MesSend and Module).

When the remote loop is a V54 loop (BTE384, and HDLC is not used), the following menus are displayed.

22030_12 © 2013 Tellabs.

TraBits

The count of transmitted bits during a test (test generator connected when RL).

ErrBits

The count of errored bits during the test.

InjErr

Inject one error into the transmitted data.

Time-out

The interface controls time-out parameter can be handled in this branch.

Time-out

The interface controls time-out in minutes. (When the loop has been activated, it will be deactivated automatically after the time defined in Time-out).

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 79

4 Installation

4.6.5

ErCntrs

The error counters can be read and cleared in this branch. The fields are auto-refreshed.

ResCtrs

Clear all error counters.

FraLos

Count of frame alignment losses (read-only).

FSW

Count of faulty frame alignment words (read-only).

CRC

Count of CRC errors (read-only).

CRCE

Count of faulty CRC E-bits (read-only).

BufSlip

Count of buffer slips (read-only).

Code

Count of code errors (read-only).

RxDelay

The value describes the time which the incoming data is in the buffer before it is clocked into the cross-connection. The time value should remain the same. If the time increases or decreases, the incoming clock of the interface differs from the clock used by the cross-connection system. This field is auto-refreshed.

G.821

Branch to the standard G.821 statistics.

*Display

By pressing the ENTER key in this field the total time of the statistics can be seen on the display:Total Time9 dd 13 h 24 min 5 sWhen pressing the SCROLL keys, the display will show the available time, the unavailable time, severely errors seconds, errored seconds and degraded minutes. This field is auto-refreshed.

*ResG821

Clears the G.821 counters.

BbInfo

This branch is displayed if the interface module is BTE-384 or BTE-768.

*RxLevel

Read-only information from the received signal level.

*RxOual

Read-only information from the received signal quality with A (best quality) through F (poorest quality).The fields are auto-refreshed.

Cross-Connection Menu The cross-connection is done in the switching matrix of the NTUM. The cross-connection bus contains about 1050 cross-connectable time slots (8-bit bytes). The bits from the interfaces are collected by using this bus. The cross-connect switch combines (in other words, makes the cross-connection) the needed new bytes for the interfaces in accordance with the cross-connection commands by using 8 kbit/s granularity. The commands are stored in a non-volatile memory. The cross-connections of the target NTUM (local or remote) can be configured and seen by using the Cross-Connection menu. To simplify the use of this menu it is divided into four sub-menus.

Cross-Connection Configuration Menu Cross-connections can be created and deleted by using the Configuration menu. This sub-menu can be accessed only when the NTUM is in the stand-alone mode and the is unlocked. This sub-menu is divided into sub-menus to the configuration of the various cross-connection formats (TS pair, TS area and TS bits) and the powerful delete operation (Del All). The following fields are common to all of these sub-menus:

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 80

22030_12 © 2013 Tellabs.

4 Installation

Oper

This is the leftmost field of the TS pair, TS area and TS bits sub-menus and it is used to execute the desired cross-connection operation that is either CreCons (create) or DelCons (delete). When it has been selected by using the SCROLL keys, the operation can be executed by pressing the ENTER key. Before executing the cross-connection operation all parameters should be set.

Dir

This field is used to specify the directionality of the cross-connection: either unidirectional (A→B) or bidirectional (A⇔ B).

XB+XD

This field is used to specify the channel of the cross-connection. The n x 8 kbit/s and n x 64 kbit/s groups mapped by the channel interfaces are called the XB channel. The XB channel can be a combination of 64 kbit/s and 8 kbit/s signals. If the interfaces are equipped with signalling or control signals, they are mapped either to the XB channel or to the corresponding signalling bits (n x 500 bit/s) of the XD channel. In the later case the signals are mapped to the G.704 compliant multiframe of the 2 or 8 Mbit/s trunk. The n x 500 bit/s signalling bits are called the XD channel of the interface. The number of the signalling bits depends on the capacity of the XB channel. Data interfaces do not normally use the XD channel. Signalling bits are reserved for the XB channel in the following way.

XB Capacity

XD Capacity

TSn/B1…B8

64 kbit/s

4 bits (a,b,c,d bits in G.704 structure)

TSn/B1…B4

32 kbit/s

2 bits (a,b)

TSn/B5…B8

32 kbit/s

2 bits (c,d)

TSn/B1…B2

16 kbit/s

1 bit (a )

TSn/B3…B4

16 kbit/s

1 bit (b )

TSn/B5…B6

16 kbit/s

1 bit (c )

TSn/B7…B8

16 kbit/s

1 bit (d )

The a, b, c and d bits of the XD channel in the G.704 multiframe correspond to the XB channel time slots in the G.704 frame. The capacity reserved by XB and XD channels is determined by the interface type and the requirements. Four signalling bits are reserved for each time slot. Even if only some of the bits are needed, all four bits are cross-connected and transferred to the far-end channel interface.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 81

4 Installation

Fig. 35 XB and XD Channels in Network

X-Group

If the cross-connection is a part of the cross-connection group (X-Group), the ID of the group can be set by using this field. A zero X-Group ID indicates that the cross-connection is not a member of any of the X-Groups and it is always in the active state. The X-Group IDs 1…16382 are valid.

Time Slot Pair

The TS pair cross-connection format describes the connection between the time slot of an interface and another time slot of the same or another interface. Both interfaces of the connection should reside in the same NTUM (local or remote).

The TS Pair sub-menu contains the following fields: Oper X-Group, Dir, XB+XD, IF A, IF B, TS A, TS B where • IF A: Interface number (only locked interfaces are valid). This is the source interface of the unidirectional connection. • IF B: Interface number (only locked interfaces are valid). This is the destination interface of the unidirectional connection. • TS A: Number of the time slot in the IF A. This is the source time slot of the unidirectional connection. • TS B: Number of the time slot in the IF B. This is the destination time slot of the unidirectional connection. Example: DIR = A<->B, XB, IF A = 1, IF B = 2, TS A = 2, TS B = 5

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 82

22030_12 © 2013 Tellabs.

4 Installation

Fig. 36 Cross-Connection of One Time Slot between Two Framed Interfaces

Time Slot Area

The TS area cross-connection format describes the connection between the continuous area of time slots of an interface and another continuous area of time slots of the same or another interface. Both interfaces of a connection should reside in the same NTUM (local or remote).

The TS Area sub-menu contains the following fields: Oper X-Group, Dir , XB+XD, IF A, IF B, fstTS A, lstTS A, fstTs B, lstTs B where • IF A: Interface number (only the locked interfaces are valid). This is the source interface of the unidirectional connection. • IF B: Interface number (only the locked interfaces are valid). This is the destination interface of the unidirectional connection. • fstTS A: Number of the first time slot of the area in the IF A. This specifies the source of the unidirectional connection. • lstTS A: Number of the last time slot of the area in the IF A. This specifies the source of the unidirectional connection. • fstTS B: Number of the first time slot of the area in the IF B. This specifies the destination of the unidirectional connection. • lstTS B: Number of the last time slot of the area in the IF B. This specifies the destination of the unidirectional connection. Example: DIR = A->B, XB, IF A = 1, IF B = 2, fstTS A = 0, lstTS A = 2, fstTS B = 3, lstTS B = 5

Fig. 37 Cross-Connection of Three Time Slots between Two Framed Interfaces 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 83

4 Installation

Time Slot Bits

The TS Bits cross-connection format describes the connection between the bits in a time slot of an interface and other bits in a time slot of the same or another interface. The interfaces that are to be connected should reside in the same NTUM (local or remote).

The TS area sub-menu contains the following fields: Oper X-Group, Dir, XB+XD, IF A, IF B, TS A, TS B, bMask A, bMask B where • IF A: Interface number (only the locked interfaces are valid). This is the source interface of the unidirectional connection. • IF B: Interface number (only the locked interfaces are valid). This is the destination interface of the unidirectional connection. • TS A: Number of the time slot in the IF A. This is the source time slot of the unidirectional connection. • TS B: Number of the time slot in the IF B. This is the destination time slot of the unidirectional connection. • bMask A: Bit mask of the TS A. The bit mask consists of eight bits (one byte) where a 1 state of a bit indicates the connection. In the interface of the NTUM the bit mask is presented in the hexadecimal format. 4.7.7 Binary-to-Hexadecimal Conversion Table contains the table for the binary to hexadecimal conversion. • bMask B: Bit mask of the TS B. Example: DIR = A<->B, XB, IF A = 1, IF B = 2, TS A = 2, TS B = 5, bMask A = 85H, bMask = 62H

Fig. 38 Cross-Connection of Time Slot Bits

Delete All

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 84

This menu is used to delete all cross-connections of the target NTUM (local or remote). The X-Group identifier of the cross-connections to be deleted can be specified. The default value of the X-Group identifier is Any, which will delete all cross-connections of the target NTUM.

22030_12 © 2013 Tellabs.

4 Installation

Cross-Connection Display Menu By using this menu the current state of the cross-connections can be seen. Also the existing cross-connections can be deleted more efficiently than by using the Configuration menu. The X-Group identifier and one interface of the cross-connections to be displayed can be specified. To see the existing cross-connections, press the ENTER key twice when the cursor blinks over the GetCons field on the upper line of the LCD display. The text Getting is shown on the display during the message send/receive operation. If the target NTUM does not contain the specified (interface, x-group) connections, the text No connections is shown. Otherwise, the first connection is shown. The cross-connection is shown so that it occupies both lines of the LCD display and the source end of the unidirectional connection is on the upper line. The rest of the connections can be viewed by using the SCROLL keys. The existing cross-connection can be deleted by using this menu only when the NTUM is in stand-alone mode and the is unlocked. To delete it, press the ENTER key when the existing cross-connection is on the display. After that, a question Delete connection? is shown. Press ENTER again if you want to delete the connection, otherwise press EXIT. X-Group Menu An x-group is a group of the cross-connections that have a common x-group identifier. The x-group is either active or ive. If the x-group is active, all cross-connections of that x-group are active. Several x-groups can be in active state at the same time if the cross-connections of these x-groups do not overlap each other. The x-group IDs 1…16382 are valid and the state of the x-groups are stored in a non-volatile memory. The x-group concept is very useful when the wishes to use one NTUM in the different cross-connection configurations. It is much more simple to ivate the current configuration and activate the new one by ivating and activating the x-groups than deleting the current commands and creating new ones by using the Cross-Connection Configuration menu. The state of the x-groups of the NTUM can be configured and seen by using the X-Group menu. To simplify the use of this menu it is divided into two sub-menus (Config, Display). • Configuration: This menu is used to activate and ivate the x-groups. It can be accessed only when the NTUM is in stand-alone mode and the is unlocked. The x-group configuration menu consists of the following fields. • Oper: This field specifies an operation which is used either to activate (ActGrp) or to ivate (Grp). When the operation has been selected by using the SCROLL keys, the operation can be executed by pressing the ENTER key. Before executing the operation the x-group should be specified. • X-Group: This field is used to specify the x-group to be activated or ivated. • Display: By using this menu the current state of the x-groups can be seen and their states can be changed. To see the state of the x-groups of the existing cross-connections, press ENTER when the cursor blinks over the Display field. The text Getting is shown on the display during the message send/receive operation. After that the states of the first two x-groups are shown on the LCD display, each on its own line. The rest of the x-groups can be viewed by using the SCROLL keys. The letter E in the status line of an x-group indicates that the x-group is empty, in other words it does not contain any cross-connections. 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 85

4 Installation

The state of the x-groups can be changed by using this menu only when the NTUM is in stand-alone mode and the is unlocked. To change the state of the x-group, press ENTER when the cursor is on the upper line of the display. After that the question Activate/ivate X-Group n? is shown. Press ENTER again if you want to change the state, otherwise press EXIT. Note that x-group 0 is always active and it is not possible to change its state. Interface Capacity Menu This menu displays the cross-connection capacity of the locked interfaces of the target NTUM (local or remote). The capacity of an interface is displayed in the time slots + bits format. Each time slot contains eight bits. If the interface has signalling capacity, the XD symbol is added at the end of the line. To see the capacity of the interfaces, press ENTER when the cursor blinks on the IF Cap? text. The capacities of the two first interfaces are displayed and the rest of the interfaces can be viewed by using the SCROLL keys.

4.6.6

Copy Settings Menu The interface parameters can be copied from one interface to another (the locking state and the configured module type are not copied). Also the cross-connection of one interface can be copied to another, or the whole cross-connection of the device can be copied. The copying possibility depends on the mode of the device and the state.

Copy Interface Parameters Menu The copying of the interface parameters is started by pressing the ENTER key in the IfParam field. After that the text yFrom is shown on the display. Now the ENTER key must be pressed and the cursor moves on the LocIf1 text. Then the interface where parameters will be copied from is selected by using the SCROLL keys. When the interface has been selected, the reading of the parameters is activated by pressing the ENTER key and the text yTo is displayed. Now the ENTER key must be pressed and the cursor moves to the interface selection. The interface where parameters will be copied to is selected with the SCROLL keys and the parameters are copied by pressing the ENTER key. Copy Cross-Connections Menu The copying of the cross-connections is started by pressing the ENTER key in the X-Con field. After that the yFrom text is shown on the display. Now the ENTER key must be pressed and the cursor moves on the LocIf1 text. The cross-connection(s) that are to be copied are selected using the SCROLL keys. When the interface/device has been selected, the reading of the cross-connections is activated by pressing the ENTER key and the text yTo is displayed. Now the ENTER key must be pressed and the cursor moves to the interface/device selection. The target to which the cross-connections are to be copied is selected with the SCROLL keys. The copy of the cross-connections is confirmed by pressing the ENTER key. If the selected interface where the copy has been performed from has connections only to one interface, the text Peer interface is IF1 appears on the LCD display where the can select the other interface of the cross-connection(s). Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 86

22030_12 © 2013 Tellabs.

4 Installation

The copying of the cross-connections is confirmed by pressing the ENTER key.

4.6.7

Entering Security Menu of Tellabs 8120 Mini Node M To enter the Security menu, press all the four keys simultaneously for about five seconds until the display shows the items of the Security menu. This must be performed as the first operation after a reset and within 30 seconds from the activation of the display.

4.7

Recommended Settings of Framed Interfaces In the next chapter there are some examples of setting parameters for framed interfaces.

4.7.1

Framed Interface Used as 2048 kbit/s Trunk Main Parameters Bit rate

2048 kbit/s

Framing

ON

Control type

Normal

Buffer length

4 Frames

Bit Usage FSW usage

FSW Regenerate

TS0 B1 usage

CRC

CRC E-bits usage

Rem end error ind

TS0

B4 B5 B6 B7 B8

Permanent 1 HDLC HDLC HDLC HDLC

HDLC link

ON

Master clock RAI

OFF

TS0

Free TS Data 1

2

3

4

5

6

7

8

1

1

1

1

1

1

1

1

CAS Free bits

22030_12 © 2013 Tellabs.

ON B5 B7 B8

Permanent 1 Permanent 1 Permanent 1

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 87

4 Installation

NNM Parameters NNM options Neighbour supervision

Off

State monitoring

Off

Message sending

On

Node

Any

Subrack

Any

Unit

Any

Link

Any

Interface

Any

Port

Any

Expected neighbour

4.7.2

Framed Interface Used as 2048 kbit/s Access Point Main Parameters Bit rate

2048 kbit/s

Framing

ON

Control type

Normal

Buffer length

4 Frames

Bit Usage FSW usage

FSW Regenerate

TS0 B1 usage

CRC

CRC E-bits usage

Rem end error ind

TS0

B4 B5 B6 B7 B8

Permanent 1 Permanent 1 Permanent 1 Permanent 1 Permanent 1

HDLC link

OFF

Master clock RAI

OFF

--

Free TS Data 1

2

3

4

5

6

7

8

1

1

1

1

1

1

1

1

CAS Free bits

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 88

ON B5 B7 B8

Permanent 1 Permanent 1 Permanent 1

22030_12 © 2013 Tellabs.

4 Installation

NNM Parameters NNM options Neighbour supervision

Off

State monitoring

Off

Message sending

Off

Node

Any

Subrack

Any

Unit

Any

Link

Any

Interface

Any

Port

Any

Expected neighbour

The HDLC channel is not used in a access point. Because the HDLC channel is not used, all NNM options are set to the off state. CAS will be used if the access device needs the channel associated signalling. CRC shall be used if the access device can use G.704 framing with CRC-4. If the CRC is not used, the recommended usage for TS0 B1 is Permanent 1.

4.7.3

Framed Interface Used as 8448 kbit/s Trunk Main Parameters Bit rate

8448 kbit/s

Framing

ON

Control type

Normal

Buffer lenght

4 Frames

Bit Usage TS99 B1…B7 usage

CRC

TS99 B8 usage

Permanent 1

TS66 B8 usage

Permanent 1

CRC E-bits usage

Rem end error ind

HDLC link

ON

TS33

Bit mask

Master clock RAI

22030_12 © 2013 Tellabs.

1

2

3

4

5

6

7

8

1

1

1

1

1

1

1

1

OFF

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 89

4 Installation

Free TS Data 1

2

3

4

5

6

7

8

1

1

1

1

1

1

1

1

ON

CAS, All Groups Free bits

B5 B7 B8

Permanent 1 Permanent 1 Permanent 1

NNM Parameters NNM options Neighbour supervision

Off

State monitoring

Off

Message sending

On

Node

Any

Subrack

Any

Unit

Any

Link

Any

Interface

Any

Port

Any

Expected neighbour

4.7.4

BTE-384-M Settings Main Parameters Bit rate

6 x 64 kbit/s (384 kbit/s)

Framing

ON

Control type

Normal

Buffer lenght

4 Frames

Bit Usage FSW usage

FSW Regenerate

TS0 B1 usage

CRC

CRC E-bits usage

Rem end error ind

TS0

HDLC link

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 90

B4 B5 B6 B7 B8

Permanent 1 HDLC HDLC HDLC HDLC ON

TS0

22030_12 © 2013 Tellabs.

4 Installation

OFF

Master clock RAI

Free TS Data 1

2

3

4

5

6

7

8

1

1

1

1

1

1

1

1

Baseband Line connection

2-wire full duplex

Scrambler type

V.32

Scrambler mode

Call

Output level

+0 dBm

Wetting current

Off

CAS

OFF

NNM Parameters NNM options Neighbour supervision

Off

State monitoring

Off

Message sending

On

Node

Any

Subrack

Any

Unit

Any

Link

Any

Interface

Any

Port

Any

Expected neighbour

The Baseband settings depend on which equipment Tellabs 8120 mini node M is connected to. These settings are for connection to a Tellabs 8100 node. If the piece of equipment connected to Tellabs 8120 mini node M is SBM 384A, the Scrambler mode setting will be Answer and the Wetting current setting will be in the On state.

4.7.5

BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M Settings Main Parameters

22030_12 © 2013 Tellabs.

Bit rate (depends on the module)

5 x 64 kbit/s (BTE-320-M) 9 x 64 kbit/s (BTE-576-M) 17 x 64 kbit/s (BTE-1088-2W-M) 36 x 64 kbit/s (BTE-2304-M)

Framing

ON

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 91

4 Installation

Main Parameters Control type

Normal

Buffer length

4 frames

Bit Usage FSW usage

FSW Regenerate

TS0 B1 usage

CRC

CRC E-bits usage

Rem end error ind

TS0

B4 B5 B6 B7 B8

Permanent 1 HDLC HDLC HDLC HDLC

HDLC link

ON

Master clock RAI

OFF

TS0

Free TS Data 1

2

3

4

5

6

7

8

1

1

1

1

1

1

1

1

Baseband Line connection

2-wire full duplex

Scrambler type

V.32

Scrambler mode

Call/Answer26

Output level

+13.5 dBm

Timing

Master/Slave26

CAS

OFF

NNM Parameters NNM options Neighbour supervision

Off

State monitoring

Off

Message sending

On

Node

Any

Subrack

Any

Expected neighbour

26It

depends on the other end settings.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 92

22030_12 © 2013 Tellabs.

4 Installation

NNM Parameters

4.7.6

Unit

Any

Link

Any

Interface

Any

Port

Any

Cross-Connection Example IF 1; trunk <-> IF3; V.35 64kbit/s + CRC + Control Channel (8 kbit/s) IF Cap = 1TS+2bits (Use the menu to get this information) DIR = A<->B, XB, IF A = 1, IF B = 3, TS A = 4, TS B = 0 DIR = A<->B, XB, IF A = 1, IF B = 3, TS A = 6, TS B = 1, bMask A = c0H, bMask B = 03H

Fig. 39 Cross-Connecting Example

4.7.7

Binary-to-Hexadecimal Conversion Table CCITT BITS

22030_12 © 2013 Tellabs.

BIT MASK IN

B1

B2

B3

B4

HEXADECIMAL

B5

B6

B7

B8

FORMAT

0

0

0

0

0

0

0

0

1

1

0

0

1

0

2

0

0

1

1

3

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 93

4 Installation

CCITT BITS

BIT MASK IN

B1

B2

B3

B4

HEXADECIMAL

B5

B6

B7

B8

FORMAT

0

1

0

0

4

0

1

0

1

5

0

1

1

0

6

0

1

1

1

7

1

0

0

0

8

1

0

0

1

9

1

0

1

0

A

1

0

1

1

B

1

1

0

0

C

1

1

0

1

D

1

1

1

0

E

1

1

1

1

F

Examples on Binary-to-Hexadecimal Conversion CCITT BITS

4.8

BIT MASK IN

B1

B2

B3

B4

B5

B6

B7

B8

HEXADECIMAL FORMAT

0

0

0

0

0

0

0

1

01

0

0

0

0

0

0

1

1

03

0

0

0

0

0

1

1

1

07

0

0

0

0

1

1

1

1

0F

0

0

0

1

1

1

1

1

1F

0

0

1

1

1

1

1

1

3F

0

1

1

1

1

1

1

1

7F

1

1

1

1

1

1

1

1

FF

0

1

0

1

1

0

1

0

5A

1

0

1

0

0

1

0

1

A5

Service Operations and Modifications Tellabs 8120 mini node M is housed in a metallic case suitable for tabletop use. Because the configuration of Tellabs 8120 mini node M is performed with various interfaces, most of the settings needed in installation can be done without opening the case. The Fig. 40 presents the mechanical construction of Tellabs 8120 mini node M. The numbers in brackets in the following description refer to the numbers in that figure.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 94

22030_12 © 2013 Tellabs.

4 Installation

Inside the metallic case there are the main unit (#6), the interface unit (#3), the power supply (#9) under the protection cover (#7) and up to four changeable interface modules (#1 and #4). In order to make any physical changes in Tellabs 8120 mini node M hardware, such as changing the interface modules, the casing must be opened. The operation must be performed by qualified personnel only, as it involves electrical safety.

Tellabs 8120 mini node M must be disconnected from the mains supply before removing the cover as high voltages are present inside Tellabs 8120 mini node M case.

The following service operations or modifications require the opening of the casing. • Changing the interface modules. • Changing the setting of the straps on the interface modules. • Updating the controller software by changing the EPROMs. The straps of the interface modules depend on the module type. Strapping instructions can be found in 4.10 Connectors and Strappings of Framed Interfaces and 4.11 Connectors and Strappings of Unframed Interfaces. The numbered items in Fig. 40 are the following:

22030_12 © 2013 Tellabs.

1.

Upper modules (unframed interfaces)

2.

Metal top cover

3.

Interface unit VCM 402

4.

Lower modules (framed interfaces)

5.

Main unit SMU 701

6.

Mains supply unit protection cover

7.

Distance bolts

8.

Power supply

9.

Screws

10.

Metallic lower casing

11.

Front

12.

Grounding earth wire

13.

Spacers

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 95

4 Installation

Fig. 40 Mechanical Construction of Tellabs 8120 Mini Node M

4.8.1

Instructions on Disassembling Tellabs 8120 Mini Node M The following steps are required when disassembling Tellabs 8120 mini node M.

Step 1

Check that Tellabs 8120 mini node M is disconnected from the mains supply.

Step 2

Loosen and remove all the screws at the back of Tellabs 8120 mini node M, slide the cover backwards and lift it off.

Step 3

To remove the upper modules (#1), loosen and remove the screws on the modules. • The upper modules can now be lifted off.

Step 4

To remove the VCM402 PCB you have to remove both upper modules first and loosen and remove the distance bolts. • VCM402 can now be lifted off.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 96

22030_12 © 2013 Tellabs.

4 Installation

Step 5

To remove the lower interface modules loosen and remove the distance bolts. • The lower modules can now be lifted off.

When adding a new interface module, remove the metal plate covering the interface slot in the back . The cover is removed by bending the plate until the points of brake. If the lower interface modules are not assembled, it is compulsory to use spacers under the distance bolts.

Step 6

The Tellabs 8120 mini node M device is assembled in the opposite order.

Step 7

When connecting the transmission modules or the interface board to the pin connectors, take care not to bend the pins of the connectors. • Check very carefully that the pins are set into the connectors in the correct position and that the pins are not bent.

Step 8

Do not use unnecessary force when tightening the screws and nuts.

Step 9

Before connecting the power, make sure that no loose parts are left inside the box.

Step 10 When the power is connected, check that Tellabs 8120 mini node M starts running in the normal way and that no unusual alarms are visible. • Check with the service computer or with the interface of the NTU that the voltages are in normal range. • If Tellabs 8120 mini node M malfunctions, disconnect the power and check that the assembly was made correctly and that the pin connectors are positioned in the correct way.

4.9

Unit List of Tellabs 8120 Mini Node M

4.9.1

Common Units

a

27The

Name

Description

SMU-M

Multiplexer for two G.704 interfaces and four V type interfaces

SMU 701

Main unit

1

VCM 402

V interface base unit

1

SMZ 414

Tellabs 8120 mini node M program

1

8990NFS40

AC/DC power supply

0…1/SMU

Unit power supply module, 19…36 V DC, negative pole earthed

0…1/SMU

Unit power supply module, 40…60 V DC, positive pole earthed

0…1/SMU

42227

b

PDU

c

PDU 423

Equipping

product has been discontinued.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 97

4 Installation

4.9.2

Main Interface Modules (G.704 framed interfaces IF1 and IF2, 1 interface/module)

28The

Name

Description

Equipping

a

LTE-M28 LTE 404

Line terminal 2 or 1 Mbit/s LTE-M base module

0…2/SMU 1/LTE-M

b

OTE-LED-M OTE 405

Optical LED 2 or 8 Mbit/s OTE-LED-M base module

0…2/SMU 1/OTE-LED-M

c

BTE-384-M28 BTE 406 DPZ 380

Baseband module 384 kbit/s Baseband base module 128…384 kbit/s Parameter PROM

0…2/SMU 1/BTE-384-M 1/BTE 406

d

G703-75-M GDH 477

G703 2 Mbit/s, 75 Ω coaxial G703-75-M base module

0…2/SMU 1/G703-75-M

e

G703-120-M GDH 487

G703 2 Mbit/s, 120 Ω symmetrical G703-120-M base module

0…2/SMU 1/G703-120-M

f

G703-8M-M28 GDH 508

G703 8 Mbit/s, 75 Ω coaxial G703-8M-M base module

0…2/SMU 1/G703-8M-M

g

BTE-2048-M28 BTE 424 BAI 482 DPZ 498

Baseband module 2048 kbit/s Baseband base module Baseband analog submodule Signal processor PROM

0…2/SMU 1/BTE 1/BTE 1/BTE

h

BTE-20482W-M28 BTE 496 BAI 497 DPZ 578

T-SDSL module 2048 kbit/s 2w T-SDSL base module T-SDSL analog submodule Signal processor PROM

0…2/SMU 1/BTE 1/BTE 1/BTE

i

BTE-1088-M28 BTE 479 BAI 483 DPZ 498

Baseband module 1088 kbit/s Baseband base module Baseband analog submodule Signal processor PROM

0…2/SMU 1/BTE 1/BTE 1/BTE

j

BTE-4096-M28 BTE 481 BAI 484 DPZ 498

Baseband module 4096 kbit/s Baseband base module Baseband analog submodule Signal processor PROM

0…2/SMU 1/BTE 1/BTE 1/BTE

product has been discontinued.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 98

22030_12 © 2013 Tellabs.

4 Installation

4.9.3

Name

Description

Equipping

k

V35-G704-SM28 VDH 474

V.35 n x 64 kbit/s…2 Mbit/s scrambler V35-G704-SM base module

0…2/SMU 1/V35-G704-SM

l

X21-G704-SM28 XDH 473

X.21 n x 64 kbit/s…2 Mbit/s scrambler X21-G704-SM base module

0…2/SMU 1/X21-G704-SM

m

BTE-320-M28 BTE 592 DPZ 650

T-SDSL module 320 kbit/s, 2-wire T-SDSL base module Signal processor PROM

0…2/SMU 1/BTE 1/BTE

n

BTE-576-M28 BTE 596 DPZ 650

T-SDSL module 576 kbit/s, 2-wire T-SDSL base module Signal processor PROM

0…2/SMU 1/BTE 1/BTE

o

BTE-10882W-M28 BTE 559 DPZ 650

T-SDSL module 1088 kbit/s, 2/4-wire T-SDSL base module Signal processor PROM

0…2/SMU 1/BTE 1/BTE

p

BTE-2304-M28 BTE 562 DPZ 650

T-SDSL module 2304 kbit/s, 2/4-wire T-SDSL base module Signal processor PROM

0…2/SMU 1/BTE 1/BTE

V Series Interface Modules (Interfaces IF3-IF6)

22030_12 © 2013 Tellabs.

Name

Description

Equipping

a

V35-M VDM 409

V.35 48, 56, n x 64 kbit/s interface module, 2 ch V35-M base module

0…2/SMU 1/V35-M

b

V36-M28 VDM 410

V.36 48, 56, n x 64 kbit/s interface module, 2 ch V36-M base module

0…2/SMU 1/V36-M

c

V24-DCE-M28 VDS 411

V.24/V.28 IF/DCE, 0.6…64 kbit/s IF module, 2 ch V24-DCE-M base module

0…2/SMU 1/V24-DCE-M

d

V24-DTE-M28 VDS 416

V.24/V.28 IF/DTE, 0.6…64 kbit/s IF module, 2 ch V24-DTE-M base module

0…2/SMU 1/V24-DTE-M

e

X21-M XDM 412

X.21 0.6…n x 64 kbit/s interface module, 2 ch X21-M base module

0…2/SMU 1/X21-M

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 99

4 Installation

Name

Description

Equipping

f

G703-64-M29 GCL 413

G.703 64 kbit/s co/contradir. interface module, 2 ch G703-64-M base module

0…2/SMU 1/G703-64-M

g

V35/V24-M29 VDM 434

V.35-IEC+V.24/DCE, 0.6…n x 64 kbit/s, 2 ch V35-IEC/V24-DCE-M base module

0…2/SMU 1/V35-IEC/V24

h

HSSI-M28 HDH 708

HSSI, 0.6…n x 64 kbit/s interface module, 1 ch HSSI-M base module

0…2/SMU 1/HSSI-M

i

Mini LAN Module EBH719

Mini LAN Module, interface module, 1 ch Mini LAN Module base module

0…2/SMU 1/Mini LAN Module

4.10 Connectors and Strappings of Framed Interfaces 4.10.1

G703-75-M and G703-120-M, G.703 2 Mbit/s

Front of G703-75-M

Fig. 41 Front of G703-75-M

The G703-75-M module is used when 75 Ω coaxial cable interface is needed. The Tx and Rx coaxial cable shields are fixed to ground. The connector is coaxial SMB.

29The

product has been discontinued.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 100

22030_12 © 2013 Tellabs.

4 Installation

Front of G703-120-M

Fig. 42 Front of G703-120-M

The G703-120-M module is used when 120 Ω symmetrical cable interface is needed.

Fig. 43 D-Type 9-Pin Female Connector

J1 Connector Pins (v1.0) Pin

Signal

1

Transmit signal B

2

Transmit signal A

4

Receive signal B

5

Receive signal A

6

Tx cable shield

9

Rx cable shield

J1 Connector Pins (v2.0 or higher) Pin

Signal

1

TxB

2

TxA

4

RxB

5

RxA

6

Ground

9

Ground

Settings for Use with 120 Ω Symmetrical Cable Strapping instructions for v1.0 are as follows. 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 101

4 Installation

Strap

Main Position

Alternative Position

Function of Main Position

CN5

ON

OFF

Tx cable shield grounded

CN8

ON

OFF

Rx cable shield grounded

Note that there are no strappings with v2.0 or higher.

4.10.2

LTE-M Line Terminal 1 or 2 Mbit/s

Front

Fig. 44 Front of LTE-M

Fig. 45 D-Type 9-Pin Female Connector

P2 Connector Pins Pin

Signal

1

Transmit signal B

2

Transmit signal A

4

Receive signal B

5

Receive signal A

6

Tx cable shield

9

Rx cable shield

Settings for Use with 120 Ω Symmetrical Cable Strap

Main Position

Alternative Position

Function of Main Position

S1

2

1

Tx cable shield grounded

S2

1

2

Rx cable shield not grounded

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 102

22030_12 © 2013 Tellabs.

4 Installation

4.10.3

G703-8M-M, 8 Mbit/s

Front

Fig. 46 Front of G703-8M-M

The connector is coaxial SMB. Strappings There are no strappings on the G703-8M-M module. The Rx and Tx coaxial cable shields are fixed to ground.

4.10.4

OTE-LED-M, Optical LED, 2 or 8 Mbit/s

Front

Fig. 47 Front of OTE-M

The connector is a standard optical connector of FC type. Strappings There are no strappings on the OTE-M module.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 103

4 Installation

4.10.5

BTE-384-M, BTE-1088-M, BTE-2048-M, BTE-2048-2W-M and BTE-4096-M, 384 kbit/s…4224 kbit/s

Front

Fig. 48 Front of BTE-384-M, BTE-1088-M, BTE-2048-M, BTE-2048-2W-M and BTE-4096-M

Fig. 49 D-Type 9-Pin Female Connector

Pin Assignment at CN1 4-WIRE USE

2-WIRE USE

Pin

BTE-384-M

BTE-2048-2W-M

1

Transmit signal B

Not connected

Tx/Rx signal B

2

Transmit signal A

Not connected

Tx/Rx signal A

3

Not connected

Not connected

Not connected

4

Receive signal B

Tx/Rx signal B

Not connected

5

Receive signal A

Tx/Rx signal A

Not connected

6

TX cable shield

Not connected

Not connected

7

Not connected

Not connected

Not connected

8

Not connected

Not connected

Not connected

9

RX cable shield

Cable shield

Cable shield

Strappings in BTE-384-M There are two strappings available on the BTE-384-M baseband module.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 104

22030_12 © 2013 Tellabs.

4 Installation

• S1: TX direction cable shield grounded/not grounded • S2: RX direction cable shield grounded/not grounded (RX/TX direction in BTE-384 in 2-wire mode) • S3/S4: wetting current enabled/disabled • If wetting current is enabled, it can be turned ON or OFF in Tellabs 8000 manager. If wetting current is disabled, this function is disabled in Tellabs 8000 manager. • If the customer wants to enable switching of wetting current, both S3 and S4 must be in position ON. This mode is not recommended due to EMC requirements.

Fig. 50 BTE-384-M Strappings

The strappings are located near the line connector. The default position of the strappings is off, shields not grounded.

Fig. 51 S3 and S4 Located between Line Transformers M1 and M2

Strappings in Other BTE Modules There are two strappings available on the module. • J1: TX direction cable shield grounded/not grounded • J4: RX direction cable shield grounded/not grounded 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 105

4 Installation

Fig. 52 BTE Strappings

The strappings are located near the line connector. The default position of the strappings is off, shields not grounded. This strapping information does not concern the following BTE modules, BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M. These modules do not have any strappings.

4.10.6

BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M, 320…2304 kbit/s

Front

Fig. 53 Front of BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M Modules

Fig. 54 D-Type 9-Pin Female Connector

Pin Assignment at CN1 Pin

4-WIRE USE (BTE-1088-2W-M, BTE-2304-M)

2-WIRE USE (BTE-320-M, BTE-576-M, BTE-1088-2W-M, BTE-2304-M)

1

Transmit signal B

Tx/Rx signal B

2

Transmit signal A

Tx/Rx signal A

3

Not connected

Not connected

4

Receive signal B

Not connected

5

Receive signal A

Not connected

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 106

22030_12 © 2013 Tellabs.

4 Installation

Pin

4-WIRE USE (BTE-1088-2W-M, BTE-2304-M)

2-WIRE USE (BTE-320-M, BTE-576-M, BTE-1088-2W-M, BTE-2304-M)

6

Not connected

Not connected

7

Not connected

Not connected

8

Not connected

Not connected

9

Not connected

Not connected

Strappings in BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M Modules The BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M modules do not have any strappings.

4.10.7

V35-G704-SM, V.35 n x 64 kbit/s…2 Mbit/s

Front

Fig. 55 Front of V35-G704-SM Module

Fig. 56 D-Type 9-Pin Female Connector

D-Type 9-Pin Female Connector

22030_12 © 2013 Tellabs.

Pin

Signal

Name (DTE)

Direction

1

Transmit Signal B

104B

Out

2

Transmit Signal A

104A

Out

3

Ground

4

Receive Signal B

103B

In

5

Receive Signal A

103A

In

6

Transmit Clock B

115B

Out

7

Transmit Clock A

115A

Out

8

Receive Clock B

113B

In

9

Receive Clock A

113A

In

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 107

4 Installation

Strappings All strappings of the module must be in position 1.

4.10.8

X21-G704-SM, n x 64 kbit/s…2Mbit/s

Front

Fig. 57 Front of X21-G704-SM

Fig. 58 D-Type 9-Pin Female Connector

D-Type 9-Pin Female Connector Pin

Signal

Name (DTE)

Direction

Notice

1

Transmit Signal B

T/b

Out

2

Transmit Signal A

T/a

Out

3

Ground

G

4

Receive Signal B

R/b

In

5

Receive Signal A

R/a

In

6

Transmit Clock B

X/b

Out

7

Transmit Clock A

X/a

Out

8

Receive Clock B

S/b

In

DCE, out

9

Receive Clock A

S/a

In

DCE, out

Strappings All strappings of the module must be in position 1 when used in DTE mode. All strappings of the module must be in position 2 when used in DCE mode. The factory settings are in position 1. Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 108

22030_12 © 2013 Tellabs.

4 Installation

4.11 Connectors and Strappings of Unframed Interfaces 4.11.1

V35-M, V.35 48, 56, n x 64 kbit/s Interfaces, 2 pcs

Fig. 59 Front of V35-M Module

Fig. 60 34-Pin Female Connector

The V.35 interface is equipped with a rectangular 34-pin female connector according to ISO 2593 Standard. The nominal connector pin diameter is 1.6 mm. The connector is provided with two UNC 6-32 locking screws. Data and timing signals are symmetrical with a level of 0.55 V (+ 20%) to 100 Ω load. The electrical characteristics of the control circuits are in accordance with V.28. V35 Connector Pin Assignment

22030_12 © 2013 Tellabs.

Pin Number

CCITT V.35 Circuit Number

Input/Output

A

---

Cable shield

B

102

Signal ground

P

103A

S

103B

R

104A

T

104B

C

Signal Level

Signal

input

Transmitted data

V.35

output

Received data

V.35

105

input

Request to send

V.28

D

106

output

Ready for sending

V.28

E

107

output

Data set ready

V.28

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 109

4 Installation

4.11.2

Pin Number

CCITT V.35 Circuit Number

Input/Output

Signal Level

Signal

F

109

output

Signal detector

V.28

H

108

input

Data terminal ready

V.28

U

113A

input

Transmitted data timing from DTE

V.35

W

113B

Y

114A

output

Transmitted data timing from VCM

V.35

AA

114B

V

115A

output

Received data timing from VCM

V.35

X

115B

N

140

input

Remote loop-back

V.28

L

141

input

Local loop-back

V.28

NN

142

output

Test indicator

V.28

V36-M, V.36 48, 56, n x 64 kbit/s Interfaces, 2 pcs

Fig. 61 Front of V36-M Module

Fig. 62 D-Type 37-Pin Female Connector

The V.36 interface is provided with a 37-pin female D-connector according to ISO 4902 Standard. The connector is furnished with two either UNC 4-40 or M3 locking screws. Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 110

22030_12 © 2013 Tellabs.

4 Installation

V36 Connector Pin Assignment Pin Number

CCITT V.36 Circuit Number

1

---

Cable shield

19, 20

102

Signal ground

4

103A

22

103B

6

104A

24

104B

7

105A

25

105B

9

106A

27

106B

11

107A

29

107B

13

109A

31

109B

12

108A

30

108B

17

113A

35

113B

5

114A

23

114B

8

115A

26

115B

14 10 18

22030_12 © 2013 Tellabs.

Input/ Output

Signal Level

Signal

input

Transmitted data

V.11

output

Received data

V.11

input

Request to send

V.11

output

Ready for sending

V.11

output

Data set ready

V.11

output

Signal detector

V.11

input

Data terminal ready

V.11

input

Transmitted data timing from DTE

V.11

output

Transmitted data timing from VCM

V.11

output

Received data timing from VCM

V.11

140

input

Remote loop-back

V.28

141

input

Local loop-back

V.28

142

output

Test indicator

V.28

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 111

4 Installation

4.11.3

V24-DCE-M, V.24/V.28 if/DCE, 0.6…64 kbit/s, 2 pcs

Fig. 63 Front of V24-DCE-M Module

Fig. 64 D-Type 25-Pin Female Connector

The V.24/V.28 interface is provided with a 25-pin female D-connector according to ISO 2110 Standard. The connector is furnished with two either UNC 4-40 or M3 locking screws. The electrical characteristics of all circuits are according to V.28. V24/V.28 Connector Pin Assignment Pin Number

CCITT V.24 Circuit Number

1

---

Cable shield

7

102

Signal ground

2

103

input

Transmitted data

3

104

output

Received data

4

105

input

Request to send

5

106

output

Ready for sending

6

107

output

Data set ready

8

109

output

Signal detector

20

108

input

Data terminal ready

24

113

input

Transmitted data timing from DTE

15

114

output

Transmitted data timing from VCM

17

115

output

Received data timing from VCM

21

140

input

Remote loop-back

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 112

Input/Output

Signal

22030_12 © 2013 Tellabs.

4 Installation

4.11.4

Pin Number

CCITT V.24 Circuit Number

Input/Output

Signal

18

141

input

Local loop-back

25

142

output

Test indicator

9

---

output

+10 V output via 321R

10

---

output

-10 V output via 321R

11-14

---

Not connected

16, 19

---

Not connected

22, 23

---

Not connected

V24-DTE-M, V.24/V.28 if/DTE, 0.6…64 kbit/s, 2 pcs

Fig. 65 Front of V24-DTE-M Module

Fig. 66 D-Type 25-Pin Female Connector

V24/V.28 Connector Pin Assignment

22030_12 © 2013 Tellabs.

Pin Number

CCITT V.24 Circuit Number

1

---

Cable shield

7

102

Signal ground

2

103

output

Transmitted data

3

104

input

Received data

4

105

output

Request to send

5

106

input

Ready for sending

6

107

input

Data set ready

8

109

input

Signal detector

Input/ Output

Signal

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 113

4 Installation

Pin Number

CCITT V.24 Circuit Number

Input/ Output

Signal

20

108

output

Data terminal ready

24

113

output

Transmitted data timing from VCM

15

114

input

Transmitted data timing from DCE

17

115

input

Received data timing from DCE

140

output

Remote loop-back

18

141

output

Local loop-back

25

142

input

Test indicator

9

---

output

+10 V output via 321R

10

---

output

-10 V output via 321R

11-14

---

Not connected

16, 19

---

Not connected

22, 23

---

Not connected

21

4.11.5

X21-M, X.21 1.2…n x 64 kbit/s Interface, 2 pcs

Fig. 67 Front of X21-M Module

Fig. 68 D-Type 15-Pin Female Connector

The X.21 interface is provided with a 15-pin female D-connector according to ISO 4903 Standard. The connector is furnished with two either UNC 4-40 or M3 locking screws. The electrical characteristics of all circuits are according to V.11. The X.21 interface is electrically and mechanically compatible with CCITT Recommendation X.21 for point-to-point applications. Functionally, circuits C and I correspond to V.24 circuits 105 and 109. The signal levels for all circuits are X.27 (V.11). Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 114

22030_12 © 2013 Tellabs.

4 Installation

X.21 Connector Pin Assignment

4.11.6

Pin Number

CCITT X.21 Circuit Number

1

---

2

T(A)

9

T(B)

3

C(A)

10

C(B)

4

R(A)

11

R(B)

5

I(A)

12

I(B)

6

S(A)

13

S(B)

7

X/B(A)

14

X/B(B)

Byte timing

8

G

Signal ground or common return

15

----

Not connected

Mode DCE/DTE

Signal

Cable shield input/input

Transmit

input/input

Control

output/output

Receive

output/output

Indication

output/input

Signal element timing

output/input

DTE transmit signal element timing/

G703-64-M, G.703 64 kbit/s Co/Contradirectional Interface, 2 pcs

Fig. 69 Front of G703-64-M Module

Fig. 70 D-Type 15-Pin Female Connector 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 115

4 Installation

G.703 Connector Pin Assignment Pin Number

Input/ Output

Signal

1

output

Receive data (A)

2

output

Receive data (B)

3

input

Transmit data (A)

4

input

Transmit data (B)

5

output

Receive data timing (A)

6

output

Receive data timing (B)

7

output

Transmit data timing (A)

8

output

Transmit data timing (B)

9-15

4.11.7

Ground

V35/V24-M, V.24/V.28 if/DCE, 0.6…64 kbit/s; V.35-IEC if, n x 64 kbit/s

Fig. 71 Front of V35/V24-M Module

Fig. 72 D-Type 25-Pin Female Connector

The V.24/V.28 interface is provided with a 25-pin female D-connector according to ISO 2110 Standard. The connector is furnished with two either UNC 4-40 or M3 locking screws. The electrical characteristics of all circuits are according to V.28. The pin assignment is the same as with the V24-DCE-M module (See 4.11.3 V24-DCE-M, V.24/V.28 if/DCE, 0.6…64 kbit/s, 2 pcs). The V.35-IEC interface is equipped with a 25-pin female D-connector according to ISO 2110 Standard. The connector is furnished with two either UNC 4-40 or M3 locking screws. The data and timing signals are symmetrical with a level of 0.55 V (+20%) to 100 Ω load. The electrical characteristics of the control circuits are according to V.28. Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 116

22030_12 © 2013 Tellabs.

4 Installation

V.35 IEC Connector Pin Assignment

4.11.8

Pin Number

CCITT V.35 Circuit Number

1

---

Cable shield

7

102

Signal ground

2

103A

14

103B

3

104A

16

104B

4

Input/ Output

Signal

Signal Level

input

Transmitted data

V.35

output

Received data

V.35

105

input

Request to send

V.28

5

106

output

Ready for sending

V.28

6

107

output

Data set ready

V.28

8

109

output

Signal detector

V.28

20

108

input

Data terminal ready

V.28

24

113A

input

Transmitted data timing from DTE

V.35

11

113B

15

114A

output

Transmitted data timing from VCM

V.35

12

114B

17

115A

output

Received data timing from VCM

V.35

9

115B

21

140

input

Remote loop-back

V.28

18

141

input

Local loop-back

V.28

25

142

output

Test indicator

V.28

HSSI-M, TIA/EIA 612, 0.6…8448 kbit/s

Fig. 73 Front of HSSI-M Module

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 117

4 Installation

Fig. 74 II-Type 50-Position SCSI Connector

HSSI-M Pin Assignment

30LC

Pin Number

TIA/EIA-613 Circuit Number

Input/ Output

Signal

Signal Level

1

102

-

Common

-

26

102

-

Common

-

2

115A

Output

Receiver signal element timing

TIA/EIA-612

27

115B

Output

Receiver signal element timing

TIA/EIA-612

3

107A

Output

DCE ready

TIA/EIA-612

28

107B

Output

DCE ready

TIA/EIA-612

4

104A

Output

Received data

TIA/EIA-612

29

104B

Output

Received data

TIA/EIA-612

5

LCA30

Output

Loopback request from DCE

TIA/EIA-612

30

LCB 30

Output

Loopback request from DCE

TIA/EIA-612

6

114A

Output

Transmitter signal element timing

TIA/EIA-612

31

114B

Output

Transmitter signal element timing

TIA/EIA-612

7

102

-

Common

-

32

102

-

Common

-

8

108/2A

Input

DTE ready

TIA/EIA-612

33

108/2B

Input

DTE ready

TIA/EIA-612

is not specified in TIA/EIA-613, the pair is reserved for future use interchange circuits from DCE.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 118

22030_12 © 2013 Tellabs.

4 Installation

4.11.9

Pin Number

TIA/EIA-613 Circuit Number

Input/ Output

Signal

Signal Level

9

113A

Input

Transmitter signal element timing

TIA/EIA-612

34

113B

Input

Transmitter signal element timing

TIA/EIA-612

10

143A

Input

Loopback A

TIA/EIA-612

35

143B

Input

Loopback A

TIA/EIA-612

11

103A

Input

Transmitted data

TIA/EIA-612

36

103B

Input

Transmitted data

TIA/EIA-612

12

144A

Input

Loopback B

TIA/EIA-612

37

144B

Input

Loopback B

TIA/EIA-612

13

102

-

Common

-

38

102

-

Common

-

19

102

-

Common

-

44

102

-

Common

-

24

142A

Output

Test mode

TIA/EIA-612

49

142B

Output

Test mode

TIA/EIA-612

25

102

-

Common

-

50

102

-

Common

-

Mini LAN Module, 10Base-T, 64…2048 kbit/s

Fig. 75 Front of Mini LAN Module

Fig. 76 RJ-45 Connector 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 119

4 Installation

The 10Base-T interface is implemented with an RJ-45 connector (twisted pair). The connector identification for RJ-45 is presented in Fig. 76 and the pin assignment in the table below. Pin

Signal

1

Tx+ (TD+)

2

Tx- (TD-)

3

Rx+ (RD+)

6

Rx- (RD-)

4,5,7,8

Not connected

The cabling of the LAN interface must remain inside the building.

4.12 Software Update If the controller software needs to be updated, a service computer or Tellabs 8000 manager is needed. The EPROMs inside Tellabs 8120 mini node M only include the operating system of the controller. The application software which is always needed for Tellabs 8120 mini node M to function is ed to the flash memories soldered on the main board of the equipment. Flash memories are of an electrically programmable and erasable memory type. If only the EPROMs are changed without performing a , the equipment will not operate. Updating software means in most cases only the ing of the application software. The software can be ed on a running device. After the process the piece of equipment makes a reset which causes a short (30…60 seconds) interruption to the data transmission going through the equipment. The ing process does not change any settings or the cross-connection of the equipment. The following instructions describe how to update the software of Tellabs 8120 mini node M by ing a compatible binary file through the management interface and how to replace the EPROMs on Tellabs 8120 mini node M.

4.12.1

ing Tellabs 8120 Mini Node M Software The able software for Tellabs 8120 mini node M is normally delivered as a binary SMZ4NN_X.Y file on a micro floppy disk, where X.Y is the version of the software (SMZ4NN can be either SMZ 414 or SMZ 430, depending on the type of Tellabs 8120 mini node). The able software must be compatible with the EPROM set of the target unit. The compatibility between the target unit software and the able file is defined by the following two rules: • The product codes must be the same (SMZ4NN). • Two versions, U.V and X.Y are compatible if U = X. The following instructions should be followed when ing the Tellabs 8120 mini node M software.

Step 1

Check that you have the correct able software available.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 120

22030_12 © 2013 Tellabs.

4 Installation

Step 2

Select the correct target if you are using Tellabs 8000 manager.

Step 3

Check the compatibility of the software versions.

Step 4

Open the ing window.

Step 5

Select the correct binary file SMZ4NN_X.Y from your directory. • For example: SMZ414_4.6

Step 6

Activate ing.

Step 7

Wait for the operation to end. The ing takes some minutes, including erasing time, data transfer and programming time, and checking and restarting time. After ing, check the software version.

4.12.2

Replacing EPROMs There are two EPROMs for the software. The EPROMs are labeled with the identification stickers which contain the following information: product code (SMZ4NN), version number and EVEN/ODD to indicate the positions of EPROMs.

The must be disabled before installing the EPROMs with new versions. Tellabs 8120 mini node M must be disconnected from the mains supply before removing the cover as high voltages are present inside the Tellabs 8120 mini node M case.

The following instructions should be followed when installing or replacing the EPROMs. Step 1

Check that the unit is executing the PROM application.

Step 2

Remove the metallic cover of Tellabs 8120 mini node M.

Step 3

Remove the old EPROMs from their sockets.

Step 4

Put the new EPROMs (SMZ4NN rx.y ODD and EVEN) into the sockets.

Step 5

Check the correct places of the EPROMs (see the figure below).

Step 6

Check the direction of the EPROMs. The Pin #1 end is identified by a slot at the end of the component package.

Step 7

Replace the metallic cover of Tellabs 8120 mini node M.

Step 8

the new software version.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 121

4 Installation

Fig. 77 Location for EPROMs

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 122

22030_12 © 2013 Tellabs.

5 Faults and Actions

5 Faults and Actions 5.1

Terminology The following acronyms will be used in the tables below: Maintenance Status PMA

Prompt maintenance alarm

DMA

Deferred maintenance alarm

MEI

Maintenance event information

Service Status S

Service alarm

LED Indications R

Red alarm LED

Y

Yellow alarm LED

RB

Red alarm LED blink

Consequent Actions TxAIS

AIS insertion to Tx signal

RxAIS

AIS insertion to Rx signal

TxTS-AIS

AIS insertion in time slots of Tx signal

AIS

AIS insertion to whole signal

FrFEA

Frame level far-end alarm (TS0/B3 in 2 Mbit/s frame, TS66/B7 in 8 Mbit/s frame)

MFrFEA

Multiframe level far end alarm (FR0/TS sig/B6)

Also MFrFEA is transmitted if FrFEA is transmitted.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 123

5 Faults and Actions

5.2 5.2.1

Common Faults and Actions Common Logic Faults (Block 0) Fault Condition

Status

LED

Note

Reset There has been a unit reset (detected always after the power-up of the unit)

PMA, S

R

Fault message (with delta event) appears when the unit starts to operate.

Power supply (5 V,+12 V,-12 V) The voltage generated by the main supply unit is below the threshold limit.

PMA

R

Rx signal action depends on the frame level alarm of the corresponding interface.

U memory faults RAM fault A background process has found a RAM location where the read value does not match with the written test pattern. EPROM fault The calculated check sum does not match with the stored one. FLASH faults A problem has been found when saving parameters or programs to the non-volatile memory.

PMA, S

R

-

Incompatible EPROM/FLASH SW The ed software (on the flash) is not compatible with the system software on the EPROMs.

PMA

R

-

Checksum err in ed SW The ed software has been corrupted.

PMA

R

-

SW unpredicted This fault condition should never occur (or not yet ed).

PMA

R

-

Missing settings One of the setting structures has been corrupted on the non-volatile memory.

PMA, S

R

-

Missing application program There is no application program on the flash memory. the latest version of the SMZ program.

PMA, S

R

-

Tx RAM error There is a difference between the written and read data in the Tx data buffer RAM of the framed interface.

PMA, S

R

-

Rx RAM error There is a difference between the written and read data in the Rx data buffer RAM of the framed interface.

PMA, S

R

-

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 124

22030_12 © 2013 Tellabs.

5 Faults and Actions

5.2.2

5.2.3

Master Clock Faults (Block 0) LED

Fault Condition

Status

Loss of master clock locking The internal clock is used with non-empty fallback list.

MEI

Fallback list warning The lowest choice is used (there is more than one choice in the fallback list).

MEI

Loss of external clock The external clock input is enabled but the clock, connected to input, is not acceptable.

PMA

External clock warning The external clock is included in the fallback list but the external clock input is not enabled.

MEI

Phase locked loop alarm The phase locked loop of the master clock cannot be locked to any clock.

PMA

R

Clock far end alarm choice N The state of the fallback list choice N indicates the clock far end alarm.

MEI

Y

Fault Condition

Status

LED

Block IA fault Data transfer between the cross-connection and a specified block (interface/port) does not work.

PMA, S

Y

X-connect RAM fault Problem found when configuring the cross-connect matrix.

PMA, S

R

ASIC latch error An ASIC setting cannot be corrected by a checking background process.

PMA, S

R

ASIC latch warning An ASIC setting is corrected by a checking background process.

MEI

Flash list check sum error One of the flash lists (e.g. a port descriptor list) has been corrupted.

PMA,S

X-connect flash lst conflict A corrupted cross-connect record has been found in the non-volatile memory after the unit reset. The record has been deleted.

MEI

PortDescr flash lst conflict A corrupted port descriptor record has been found in the non-volatile memory after the unit reset. The record has been deleted.

MEI

Note

R

Cross-Connect Block Faults (Block 0)

22030_12 © 2013 Tellabs.

Note

R

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 125

5 Faults and Actions

5.2.4

Fault Condition

Status

Swp trk flash lst conflict A corrupted swap trunk record has been found in the non-volatile memory after the unit reset. The record has been deleted.

MEI

trk flash lst conflict A corrupted ivate trunk record has been found in the non-volatile memory after the unit reset. The record has been deleted.

MEI

Time contr. X-conn warning A delta fault indicating a problem when switching the time controlled cross-connection on/off. Additional information can be read in the error log of the time control process.

PMA

LED

Note

Faults of Framed IF Tx Signal (Block 1, 2) Fault Condition

Status

LED

Tx signal

Tx Clock fault (PLL) The fault will be activated if the interface module transmitting clock phase locking to X-bus clock fails.

PMA, S

R

TxAIS

IA activity missing The fault will be activated if the unit cannot find its locked interface address on the cross-connection bus. The cross-connect block should activate the IA on the bus if the interface is locked.

PMA, S

R

TxTS-AIS

Bus sync. fault (block 0) No cross-connection bus sync detected.

PMA, S

R

TxTS-AIS

AIS from X-bus The fault will be activated if the frame sync. word and RAI from the X-bus and TS0B2 changes between 0 and 1 are missing.

MEI, S

Y

TxAIS31

BTE Tx line test The fault will be activated if a BTE module Tx test pattern generator is activated (used in V.54 remote loop).

MEI, S

Y

Test pattern

Bus faults

31Only

when FAS is transferred through the network.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 126

22030_12 © 2013 Tellabs.

5 Faults and Actions

5.2.5

Faults of Framed IF Rx Signal (Block 1, 2) Signal and Frame Faults

Status

LED

Rx signal

Tx signal

1.1 Interface module missing No interface module is present but one is defined in the settings.

PMA, S

R

RxAIS

-

1.2 Wrong interface module There is a conflict between the installed module and the settings.

PMA, S

R

RxAIS

Cut off

1.3 Rx signal missing The signal level is below a specific level (the level depends on the used interface module and the selected bit rate).

PMA, S

R

RxAIS

FrFEA

1.4 Rx signal is AIS The Rx signal is detected to be AIS.

MEI, S

Y

RxAIS

FrFEA

1.5.1 Frame alignment lost See CCITT G.706 Loss of frame alignment.

PMA, S

R

RxAIS

FrFEA

1.5.3 Frame alignment lost by CRC See CCITT G.706 Frame alignment recovery (2048 mode ≥915 CRC block errors detected).

PMA, S

R

RxAIS

FrFEA

1.5.2 CRC missing This fault indicates that the remote end does not use the CRC.

DMA

R

RxAIS

FrFEA

1.6 BER 10 -3 The bit error rate is calculated from faulty frame alignment words or from code errors. The 10E-3 alarm status depends on fault consequences (AIS insertion).

PMA, S

R

RxAIS

FrFEA

1.7.1 Own NNM messages received The control channel of the interface is used and the neighbour supervision option of the interface is ON and the received NNM message contains the same identification data as the NNM message sent to the interface.

PMA, S

R

RxAIS

-

1.7.2 Wrong IDs in NNM messages The control channel of the interface is used and the neighbour supervision option of the interface is ON and the received NNM message contains unexpected neighbour identification data.

PMA, S

R

RxAIS

-

1.7.3 No response to NNM message The control channel of the interface is used and the neighbour node supervision option of the interface is ON and no NNM (Neighbour Node Monitoring) message has been received from the interface in eight seconds.

PMA, S

R

RxAIS

-

1.5 Loss of frame alignment

1.7 Wrong input signal

1.8 NTU problems

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 127

5 Faults and Actions

Signal and Frame Faults

Status

LED

Rx signal

Tx signal

1.8.1 NTU power off / local loop The fault will be activated if the used module is BTE384 and the wetting current is ON and the received current value differs in frequency of 1.5…4.5 Hz and the current value difference is more than 1.5 mA.

MEI

Y

RxAIS

-

1.8.2 NTU line break The fault will be activated if the used module is BTE384 and the wetting current is ON and the received current value is lower than 1.2 mA.

MEI

Y

-

-

1.8.3 NTU short circuit The fault will be activated if the used module is BTE384 and the wetting current is ON and the received current value is higher than 6.5 mA.

MEI

Y

-

-

1.9 ASIC error The fault will be activated if difference of the write/read data of ASIC has been found.

PMA, S

R

-

-

2.1.1 Interface back to equipment An interface loop is created in the interface module. It loops the transmitted data and the clock signal back to the interface receiver.

MEI, S

Y

-

TxAIS

2.1.2 MUX/DEMUX back to eq. As in the Interface back to equipment loop above, but the loop is made before the interface module on the framing block in the base card.

MEI, S

Y

-

TxAIS

2.1.3 MUX/DEMUX back to line Rx data is looped back to the interface transmitter. When it is used, the HDLC channel works with this line loop. All other bits are looped back to the interface.

MEI, S

Y

RxAIS

2.1.4 Line loop made by neighbour This alarm will be activated if the HDLC channel is in use and MUX/DEMUX back to line loop has been made from the remote end, or the BTE module is used and the remote end has made loop by using the V.54 loop sequence.

MEI, S

Y

RxAIS

-

MEI, S

Y

-

-

PMA, S

R

RxAIS/SigTS

MFrFEA

2 Loops 2.1 Local loops

2.2 Remote loops 2.2.1 Remote controlled line loop (2.1.4) This alarm will be activated if the HDLC channel is in use and MUX/DEMUX back to line loop has been made to the neighbour unit, or the BTE module is used and the V.54 loop has been made to the remote end.

3 Multiframe level faults 3.1 Multiframe alignment lost (group N) The multiframe alignment in signalling time slot is lost.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 128

22030_12 © 2013 Tellabs.

5 Faults and Actions

MEI, S

Y

RxAIS/SigTS

MFrFEA

4.1 Frame far-end alarm (FrFEA) The alarm state of the frame far end bit is received. The alarm status depends on fault consequences (AIS insertion into the signalling time slot).

MEI, S

Y

RxAIS/SigTS

RxAIS operation can be turned off

4.2 Multiframe far-end alarm (MFrFEA) The alarm state of the multiframe far end bit is received. The alarm status depends on fault consequences (AIS insertion into the signalling time slot).

MEI, S

Y

RxAIS/SigTS

RxAIS operation can be turned off

5.1 Error rate 10 -3 See CCITT G.736. The bit error rate is calculated from faulty frame alignment words or from code errors. The 10E-3 alarm status depends on fault consequences (AIS insertion).

DMA

R

-

-

5.2 Error rate 10 -6 The BER10E-6 error rate is calculated from CRC block errors when the bit rate is ≥1024 kbit/s. The counting time is 10 s and the limit for the fault condition depends on the used bit rate (2048 limit is 10).

DMA

R

-

-

5.3 Frequency difference The measurement period is 15 s and the phase drifting limit is 5 µs. The fault will be activated if the phase drifting limit has been exceeded in three measurements out of four.

DMA

R

-

-

5.4 Buffer slips/1 hour The fault will be activated if one or more buffer slip(s) has been observed during the last hour.

MEI

RB

-

-

3.2 AIS in signalling (group N) The signal in the signalling time slot is detected to be AIS. Multiframe faults of the 8 Mbit/s signal are detected separately in each of the four signalling time slots (groups).

4 Far-End Alarms

5 Degraded Signal

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 129

5 Faults and Actions

5.2.6

5.2.7

5.2.8

1+1 Protection Switch Fault Messages (Block 0) Fault Condition

Status

LED

Rx signal

Tx signal

Protection switch forced When the unit is in 1+1 protected mode and the protection switch has been forced to select a signal from IF1 or IF2.

MEI

R

-

-

Loss of protected signal In 1+1 protection mode both interfaces IF1 and IF2 have faults which in unprotected mode have S status.

PMA, S

R

-32

-32

Miscellaneous Faults of Framed Interfaces (Block 1, 2) Fault Condition

Status

LED

Rx signal

Tx signal

Port locking conflict The fault will be activated if the cross-connection system has the port descriptor but the interface is unlocked, or if the cross-connection system has no port descriptor although the interface is locked. Use lock/unlock.

DMA

R

-

-

HDLC overlap with X-bus The fault will be activated if the HDLC control channel bit(s) are also used by the cross-connection bus.

DMA

R

-

-

Master clock RAI overlap with X-bus The fault will be activated if the MCLK/RAI bit is also used by the cross-connection bus.

DMA

R

-

-

G821 unavailable state The fault will be activated if the G.821 supervision is used and the state of the signal becomes unavailable (10 consecutive SES seconds). The fault will be deactivated when 10 consecutive non-SES seconds have been found.

PMA, S

-

-

-

G821 limit event This fault will be activated as a delta fault if G.821 supervision is used and at least one performance limit has been exceeded in a 15-minute period.

DMA

-

-

-

Faults masked/Test The fault will be activated when the interface fault mask setting is ON (all interface faults will be cleared).

MEI

Y

-

-

Fault and Service Status (PMA, DMA, MEI, S) in 1+1 Mode of Framed Interfaces In principle, both interfaces generate their own alarms (alarm messages with fault status). PMA and S statuses are processed in this mode.

32Signal

actions depend on actions of the protected interfaces.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 130

22030_12 © 2013 Tellabs.

5 Faults and Actions

5.2.9

PMA Status Processing

In protection mode the normal PMA status is changed to the DMA status, and with the PMA status there is an additional fault condition, Loss of protected signal. In normal or prefer operating modes this special condition is created when both interfaces have a fault of category 3 or worse. In forced operating mode this condition occurs if the forced interface has a fault of categories 3 through 1. The inactive interface is not able to generate a fault with the PMA status.

S Status Processing

In protection mode an S status is generated only in the Loss of protected signal fault condition.

Far-End Alarms in 1+1 Mode

A far-end alarm indicates that the Rx signal is out of service (S status). FrFEA: Rx frame out of service MFrFEA: Rx multiframe out of service Tx far-end alarms (FrFEA, MFrFEA) of both interfaces are generated assuming a fault status of the active interface. During a short period, when the change-over switch is in a transition phase, the far-end may generate an alarm even if there is no fault in the better interface. In forced operating mode only the active forced interface can cause far-end alarms to be sent.

RxAIS Processing

RxAIS and RxAIS to SigTS are always generated when FrFEA or MFrFEA are sent. AIS generating depends on the fault status of the selected interface.

Fault Conditions of Framed Interfaces

22030_12 © 2013 Tellabs.

Multiframe Alignment Lost

The fault will be activated if two consecutive faulty multiframe alignment words have been received or if all signalling time slots in one multiframe contain only zeros (0). The fault will be deactivated when the frame alignment is found and the first four bits of the signalling time slot are found to be zeros (0) and when the prior signalling time slot has had at least one bit in state 1.

Frame Far-End Alarm (FrFEA)

The state of TS0B3 frame far-end alarm bit will be switched if the opposite state is received in three consecutive frames. State 1 for alarm.

Multiframe Far-End Alarm (MFrFEA)

The state of signalling time slot frame 0 B6 alarm bit will be switched if the opposite state is received in three consecutive frames. State 1 for alarm.

AIS in Frame 2048 kbit/s and n x 64 kbit/s

A signal containing two or less zeros in a 2-frame period is recognized as an AIS signal. After AIS is detected, a signal containing three or more zeros in a 2-frame period is recognized not to be an AIS signal.

AIS in Frame 8448 kbit/s

A signal containing less than eight zeros in a 2-frame period is recognized as an AIS signal. After AIS is detected, a signal containing 12 or more zeros in a 2-frame period is recognized not to be an AIS signal.

AIS in Multiframe

A signal in the signalling time slots containing one or no zeros in a multiframe period is recognized as an AIS signal.

Error Rate 10E-3 Limits from Frame Alignment Word

2048 kbit/s and n x 64 kbit/s count time is 4 seconds: Count to activate alarm: 94 Count to inactivate alarm: 17 8448 kbit/s count time is 2 seconds: Count to activate alarm: 199 Count to inactivate alarm: 48

Error Rate 10E-3 Limits from Code Errors

Count time is one second:

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 131

5 Faults and Actions

CRC Spurious Frame Alignment Limits

CRC Missing

5.3 5.3.1

Activate

Inactivate

8448 2048 1088

8296 1973 1033

893 229 126

Rate kbit/s

Values from 1000 counted to start a new frame search

256 320 384 448 512 576 640 704 768 1088 2048 8448

613 637 660 681 700 719 736 753 768 832 915 826

The fault will be activated if in 2M mode a framing has been found and the CRC multiframe alignment has been lost 100…200 ms; or if in 8M mode more than six CRC alignment losses due to excessive block errors have been found in a period of 3 seconds. In 2M mode the fault will be deactivated if a CRC multiframe alignment has been found; in 8M mode if no more than one frame alignment lost due to excessive CRC block errors in a three-second period has been found.

Faults and Actions of Unframed Interfaces General IF Faults of Unframed Interfaces Fault Condition

Status

LED

UI2

C1

IF module missing No interface module is present but there is one defined in the settings.

PMA, S

R

-

OFF/-

Wrong interface module There is a conflict between the installed module and the settings.

PMA, S

R

-

OFF/-

Power off in input Incoming data signal (103) out of the CCITT specs.

MEI,-

Y

-

AIS

ASIC err HW error found in the ASIC.

PMA, S

R

OFF

OFF

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 132

Speed kbit/s

22030_12 © 2013 Tellabs.

5 Faults and Actions

5.3.2

IF Signal Faults of Unframed Interfaces Status

LED

UI2

C1

Interface signal missing No carrier state of the baseband module. Faulty input signal in the case of a G.703 module.

PMA, S

R

-

AIS

105 off in input 105 signal off in input and 105 supervision selected in parameters.

MEI, -

Y

-

AIS

Code errors from input Code erros (HDB3, AMI or G.703 codir/contra). No input clock (NRZ).

PMA,S R

-

AIS

Fault Condition

Note

Input signal faults (UI1)

Used when 105 should be continuously on.

Timing errors

5.3.3

Rx buffer slips Buffer slip in Tellabs 8100 bus interface, input signal (UI1) buffer slip (n x 64kbit/s).

DMA

R

-

AIS

Tx buffer slips Buffer slip in Tellabs 8100 bus interface, output signal (UI2) buffer slip (n x 64kbit/s).

DMA

R

AIS

-

Rx buffer alignment V.110 or X.30 buffer slip.

DMA

R

-

AIS

Tx buffer alignment V.110 or X.30 buffer slip.

DMA

R

AIS

-

V.110, X.30 or MartisDXX framing in use.

Net Side Signal Faults of Unframed Interfaces Status

LED

UI2

C1

Note

AIS detected from network AIS from the cross-connection bus.

MEI, S

Y

AIS

-

V.110, X30 or MartisDXX framing in use

Loss of frame sync Loss of frame sync state in the case of a V.110 or X.30.

PMA, S

R

AIS

RAI

V.110, X30 or MartisDXX framing in use

Loss of multiframe sync Loss of multiframe sync state in the case of a V.110 or X.30.

PMA, S

R

AIS

RAI

Used at bit rates ≤2.4 kbit/s.

Alarm from far end Alarm bit set in V.110 or X.30 frame.

MEI, S

Y

-

-

V.110, X30 or MartisDXX framing in use

Fault Condition Input signal from net side (C2)

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 133

5 Faults and Actions

5.3.4

5.3.5

Test Loop Activation of Unframed Interfaces Fault Condition

Status

LED

UI2

C1

Interface loop active Interface loop activated (by the manager).

MEI, S

Y

AIS

-

Local loop or test active Local loop or test activated (by the manager).

MEI, S

Y

-

AIS

V.54 loop active V.54 loop activated (by the interface signal or from the far-end).

MEI, S

Y

-

-

Performance Conditions of Unframed Interfaces Status

LED

UI2

C1

Note

G821 unavailable state The fault will be activated if the G.821 supervision is used and the state of the signal becomes unavailable (10 consecutive SES seconds). The fault will be deactivated when 10 consecutive non-SES seconds have been found.

PMA,S

-

-

-

Available when end-to-end CRC monitoring is activated.

G821 limit event This fault will be activated as a delta fault if the G.821 supervision is used and at least one performance limit has been exceeded in a 15-minute period.

DMA

-

-

-

Available when end-to-end CRC monitoring is activated.

CRC errors from far end CRC errors detected at the far-end.

DMA

R

-

-

Available when end-to-end CRC monitoring is activated.

CRC errors from near end CRC errors detected at the near-end.

DMA

R

-

-

Available when end-to-end CRC monitoring is activated.

FAS-errors Frame sync word errors detected in case of V.110 or X.30.

PMA

Y

-

-

V.110, X.30 or MartisDXX framing in use.

Fault Condition Performance conditions

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 134

22030_12 © 2013 Tellabs.

5 Faults and Actions

5.3.6

5.3.7

Common Faults of Unframed Interfaces Fault Condition

Status

LED

UI2

C1

RL state program error Remote loop state program not stored (HW error).

PMA, S

R

-

-

Bus sync. fault (block 0) No cross-connection bus sync detected.

PMA, S

R

AIS

AIS

IA activity missing The fault will be activated if the unit cannot find its locked interface address on the cross-connection bus. The cross-connect block should activate the IA on the bus if the interface is locked.

PMA, S

R

AIS

AIS

Faults masked/Test The fault will be activated when interface fault mask setting is ON (all interface faults will be cleared).

MEI, -

Y

-

-

Note

Reference Points of Unframed Interfaces The channel board in Tellabs 8120 mini M holds four identical interface blocks numbered 3 and 6. The common parts are named block 0. The signals and directions are identified as follows. Signals and Directions of Fault Conditions Reference point

Signal description

UI1

Input signal at the receive part of the interface

UI2

Output signal at the transmit part of the interface

C1

XB output signal towards the X-bus interface

C2

XB input signal from the X-bus interface, net side signal

Fig. 78 Naming of Signal Reference Points

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 135

6 Technical Specifications of Tellabs 8120 Mini Node M

6 Technical Specifications of Tellabs 8120 Mini Node M All CCITT references concern the Blue Book, 1988. When applicable, the references to former CCITT Recommendations have been amended to ITU-T references. These references include the date of the valid ITU-T Recommendation in case these are revised in the future. If a CCITT Recommendation has not been updated as ITU-T by the International Telecommunication Union, CCITT is used in this document.

6.1

Relevant Recommendations The ITU-T/CCITT Recommendations concerning Tellabs 8100 trunk interfaces and access ports are shown below. Rec.

ITU-T Date(CCITT 1988)

Main Characteristics of Equipment and Trunk Interfaces

G.703

April 1991

Physical/electrical characteristics of hierachical digital interfaces

G.704

CCITT

Synchronous frame structure used at primary and secondary hierachical levels

G.706

CCITT

Frame alignment and CRC procedures for G.704 frames

G.732

CCITT

Characteristics of primary PCM multiplexing equipment operating at 2048 kbit/s

G.736

March 1993

Characteristics of a synchronous digital multiplex equipment operating at 2048 kbit/s

G.744

CCITT

Second order PCM multiplex equipment operating at 8448 kbit/s

G.821

CCITT

Error performance of an international digital connection

G.823

March 1993

The control of jitter and wander on the 2048 kbit/s hierarchy

Standard Transmission Network Interfaces (2 Mbit/s and 8 Mbit/s) 2048 kbit/s framed interface

G.704, G.706, G.732, G.736, G.821, G.823

8448 kbit/s framed interface

G.704, G.744, G.821, G.823

Access Points For Unframed Data Interfaces33

33

V.11 (ITU-T 03/93)

Electrical characteristics for balanced double-current interface circuits

V.13 (ITU-T 03/93)

Simulated carrier control

V.14

Transmission of start-stop characters over synchronous bearer channels

All references to CCITT Recommendations, except those listed as ITU-T.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 136

22030_12 © 2013 Tellabs.

6 Technical Specifications of Tellabs 8120 Mini Node M

Access Points For Unframed Data Interfaces33 V.24

Interface circuits between DCE and DTE

V.28

Electrical characteristics for unbalanced double-current interchange circuits

V.29

9600 bits per second modem standardised for use on point-to-point 4-wire leased telephone-type circuits

V.35 (CCITT Red Book)

Data transmission at 48 kbit/s using group band modem

V.36

Modems for synchronous data transmission using group band modems

V.54

Loop test devices for modems

V.110 (ITU-T 09/92)

ISDN rate adaption for V-series interfaces

X.21 (ITU-T 09/92)

Synchronous data network interface between DCE and DTE

X.27

Same as V.11

X.30

ISDN rate adaption for X.21 interfaces

X.54

Allocation of channels on international multiplex links at 64 kbit/s.

Access Points for Voice Frequency Interfaces

6.2

G.711 (CCITT)

64 kbit/s PCM encoding

G.712 (CCITT)

4-wire voice frequency interface

G.713 (CCITT)

2-wire voice frequency interface

G.714

Separate performance characteristics for the encoding and decoding sides of PCM channels applicable to 4-wire interfaces

G.715

Separate performance characteristics for the encoding and decoding sides of PCM channels applicable to 4-wire interfaces

G.721 (CCITT 1986/88)

32 kbit/s ADPCM

G.961 (ITU-T 03/93)

Access digital section for ISDN primary rate at 2048 kbit/s

Cross-Connect Cross-connection method

Synchronous time slot interleaving

Frame frequency

8 kHz

Capacity: The sum of cross-connected signals

64 Mbit/s

Smallest cross-connect unit

8 kbit/s

Signalling cross-connection

n x 500 bit/s (channel associated signalling = CAS)

Delay of cross-connect core

n x 64 kbit/s 1 frame = 125 µs

CAS bits (500 bit/s) 2 ms

Time integrity between time slots in cross-connected signals is maintained.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 137

6 Technical Specifications of Tellabs 8120 Mini Node M

6.3

6.4

Timing Master clock frequency

16 896 kHz ±30 ppm

Master clock functional modes

Locking to the interface rx clock (n x 64 kbit/s) Locking to external clock input (n x 64 kHz) Internal mode Clock fallback list (5 levels + internal mode)

Locking frequency

n x 64 kHz ±50 ppm

External clock input

Frequency n x 64 kHz, n=1…32 Electrically G.703/75 Ω

External clock output

Frequency 2048 kHz Locked to node master clock Electrically G.703 /75 Ω

Connector type

75 Ω, SMB connector

Jitter transfer function and jitter in the output clock

G.736

G.704 Framed Interface

6.4.1

Frame and Multiframe Buffer Frame Buffer Mode

Bit Rates

Rx Delay Frames

Tx Delay Frames

Main Usage

4 Fr34

n x 64k, 2 Mbit/s, 8 Mbit/s

1…3

1

Non-trunk lines and n x 64 kbit/s trunks

8 Fr

n x 64k, 2 Mbit/s

2…6

1

Split trunk lines

8 Fr

n x 64k, 2 Mbit/s, 8 Mbit/s

1…7

1

64 Fr

n x 64k, 2 Mbit/s

1…63

1

Plesiochronous buffer

Slip rate when the incoming signal is plesiochronous Buffer Length

Slip Rate n x 64 kbit/s

Slip Rate 2 Mbit/s

Slip Rate 8 Mbit/s

4 Fr

n x 8/df35

256/df

1056/df

8 Fr (split trunk line)

2 x n x 8/df

512/df

-

8 Fr

4 x n x 8/df

1024/df

4224/df

64 Fr

32 x n x 8/df

8192/df

-

Split trunk line operation (two physical lines combined to one logical trunk):

341

Fr = 125 µs

35df=frequency

difference (input x Mbit/s signal frequency - nodes x Mbit/s frequency)

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 138

22030_12 © 2013 Tellabs.

6 Technical Specifications of Tellabs 8120 Mini Node M

• Line bit rates n x 64 kbit/s (3 ≤ n ≤ 32), 2 Mbit/s • All split components must have the same bit rate • Tolerated delay difference between lines < 50 µs Multiframe buffer modes

6.4.2

When Frame Buffer Is

MFr Buffer36

Rx Delay

Tx Delay

4…8 frames long

2 MFr

0…2 MFr

1 Fr

64 frames long

4MFr

1…3 MFr

1 Fr

Jitter and wander tolerance

G.823

8448 kbit/s Interface (CCITT G.704) Electrical interface

G.703 See 6.6.1 8448 kbit/s, G.703 Interface (G703-8M-M Module). Optical line See 6.6.5 Optical Line Interface 2048 kbit/s / 8448 kbit/s (OTE-LED-M Module).

Multiplexing method

Synchronous time slot interleaving (G.704)

Bits in time slot

8

Time slots in frame

132 numbered 0…131

Frame alignment time slot

TS0/B1…8 + TS66/B1…6

Frame alignment procedure

G.744

Far end alarm

TS66/B7

CRC error check

CRC-6 in bits TS99/B1…6 (can be disconnected)

CRC error indication to the remote end

TS99/B7

Error performance monitoring

G.821

Signalling multiframe time slots

TS67,68,69,70 (G.704)

Multiframe time slot content

F0/TS sig (0000 xyxx)

Multiframe far end alarm

F0/TS sig/B6

Multiframe alignment procedure

G.732 (same as in 2 Mbit/s interface) Separate multiframe alignment for each signalling time slot

Frames in multiframe

16

Signalling bits

4 pcs a,b,c,d / 64 kbit/s time slot 2 pcs a,b / c,d / 32 kbit/s 1 pc a / b / c /d / 16 kbit/s

Control channel datalink

n x 8 kbit/s (n=1…8) Any time slot except TS0 and TS66 Tellabs 8100 trunk lines preferable TS01/B1…B8 (64 kbit/s) or TS33/B1…B8

361

MFr = 2 ms

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 139

6 Technical Specifications of Tellabs 8120 Mini Node M

Time Slot Usage in Trunks

6.4.3

Cross-connectable time slots

120 time slots

with signalling bits (CAS)

TS5…TS32, TS34…TS65, TS71…TS98, TS100…TS131

Cross-connectable time slots without signalling bits

5 time slots TS1…TS4,TS33

Free bits

TS66/B8, TS99/B8

2048 kbit/s Interface (CCITT G.704/706) Electrical interface

G.703 See 6.6.2 2048 kbit/s, G.703 Interface (G703-75-M) and 6.6.3 2048 kbit/s, G.703 Interface (G703-120-M). Line terminal See 6.6.4 2048 kbit/s and 1088 kbit/s Line Terminal Interface (LTE-M Module). Optical line See 6.6.5 Optical Line Interface 2048 kbit/s / 8448 kbit/s (OTE-LED-M Module). V.35 See 6.5.1 V.24/V.28,V.35,V.36/V.11; 1.2…19.2 kbit/s, 48, 56, n x 64 kbit/s. V.36/V.11 See 6.5.1 V.24/V.28,V.35,V.36/V.11; 1.2…19.2 kbit/s, 48, 56, n x 64 kbit/s.

Multiplexing method

Synchronous time slot interleaving

Bits in time slot

8

Time slots in frame

32 numbered 0…31

Frame alignment time slot

TS0

Frame alignment method

G.706

Far end alarm

TS0/B3

CRC error check

CRC-4 in CRC multiframe of TS0/B1 (G.704/706,CRC can be disconnected)

CRC block error indication to the remote end

CRC multiframe E-bit

Error performance monitoring

G.821

Signalling multiframe time slot

TS16 (G.704)

Multiframe alignment time slot content

F0/TS16 (0000 xyxx)

Multiframe far end alarm

F0/TS16/B6

Multiframe alignment method

G.732

Frames in multiframe

16

Signalling bits

4 pcs a,b,c,d / 64 kbit/s time slots 2 pcs a,b / c,d / 32 kbit/s 1 pc a / b / c /d / 16 kbit/s

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 140

22030_12 © 2013 Tellabs.

6 Technical Specifications of Tellabs 8120 Mini Node M

6.4.4

Time slot usage in trunks: cross-connectable time slots with signalling bits (CAS) free bits

30 time slots , TS1…TS15, TS17…TS31 TS0/B4…8 (see Control Channel Data Link below)

Control channel datalink

n x 8 kbit/s (n=1…8) Any time slot except TS0 frame alignment bits Tellabs 8100 trunk lines preferable TS0/B5…8 (16 kbit/s)

N x 64 kbit/s Interface with G.704 Type Frame Electrical interface

N x 64 kbit/s baseband interface See 6.6.6 Baseband Line Interface 64…384 kbit/s (BTE-384-M Module) and 6.6.7 Baseband Line Interfaces 320...4224 kbit/s (BTE-1088-M, BTE-2048-M, BTE-2048-2W-M, BTE-4096-M, BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M Modules). 1088 kbit/s line terminal See 6.6.4 2048 kbit/s and 1088 kbit/s Line Terminal Interface (LTE-M Module). V.35 n x 64 kbit/s (signals 103,104,113,115; V.35 electrical specs.) V.36 n x 64 kbit/s (signals 103,104,113,115; V.11 electrical specs.) for V.35 and V.36 n=2…32, with n=32 the frame parameters are the same as in Fig. 81 in Appendix 2Fig. 81 in Appendix 2 in Tellabs ® 8120 Mini Node M Operating Manual (document number 22030_XX).

22030_12 © 2013 Tellabs.

Multiplexing method

Synchronous time slot interleaving

Bits in time slot

8

Time slots in frame

N numbered 0…n-1

Frame alignment time slot

TS0

Frame alignment method

G.706

Far end alarm

TS0/B3

CRC error check

CRC-4 in CRC multiframe of TS0/B1 (G.704/706,CRC can be disconnected)

CRC block error indication to the remote end

CRC multiframe E-bit

Error performance monitoring

G.821

Signalling multiframe time slot (TS sig.)

Last time slot in frame (TSn-1) except with n≥17 TS signalling=16

Multiframe alignment time slot content

F0/TS signalling (0000 xyxx)

Multiframe far end alarm

F0/TS signalling/B6

Multiframe alignment method

G.732

Frames in multiframe

16

Signalling bits

4 pcs a, b, c, d / 64 kbit/s 2 pcs a, b / c, d / 32 kbit/s 1 pc a / b / c / d / 16 kbit/s

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 141

6 Technical Specifications of Tellabs 8120 Mini Node M

6.5

Time slot usage in trunk lines: cross-connectable time slots with signalling bits (CAS) free bits

n-2 pcs TS0/B4…8 (see Control Channel Data Link below)

Control channel data link

n x 8 kbit/s (n=1…8) Any time slot except TS0 frame alignment bits Tellabs 8100 trunk lines preferable TS0/B5…8 (16 kbit/s)

Unframed Data Interfaces

6.5.1

V.24/V.28,V.35,V.36/V.11; 1.2…19.2 kbit/s, 48, 56, n x 64 kbit/s Interface type

V.24/V.28

V.35,V.36/V.11,V.24/ V.35,V.36,V.24 (n=1) V.28

Data bit rate

1.2, 2.4, 4.8, 7.2, 9.6, 14.4, 19.2, 38.4 kbit/s

48, 56 kbit/s

n x 64 kbit/s n=1,2,…,32

Framing inside Tellabs 8100 network

V.110

V.110

-

Interface functions

V.24

V.24

V.24

- 105/109

SB

SB

V.13

- 106

X

X

-

- 108/107

SA

SA

-

- 140/142

V.54

V.54

V.54

Handshake signal transmission37

Electrical Interface - V.24

V.28 for all signals

- V.35

V.35 for signals 103, 104, 113, 114, 115, V.28 for other signals

- V.36

V.28 for signals 140, 141 and 142, V.11 for other signals

Interface signals

102, 103, 104, 105, 106, 107, 108, 109, 113, 114, 115, 140, 141, 142

Connector type - V.24

ISO 2110, D-type 25-pin female connector

- V.35

ISO 2593, D-type 34-pin female connector

- V.35-IEC

ISO 2110, D-type 25-pin female connector

- V.36

ISO 4902, D-type 37-pin female connector

Test loops via data interface - RL, V.54 remote loop, (loop 2) - LL, V.54 local loop, (loop 3)

37SA,

SB, X are bits in V.110 frame

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 142

22030_12 © 2013 Tellabs.

6 Technical Specifications of Tellabs 8120 Mini Node M

6.5.2

X.21 1.2…19.2 kbit/s, 48, 56, n x 64 kbit/s Data bit rate

1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 48 kbit/s

56 kbit/s

n x 64 kbit/s n=1, 2,…, 32

Framing inside Tellabs 8100 network

X.30 (V.110)

V.110

-

Interface functions

V.24

V.24

-

S1+S3+S4S1, S3, S4 are bits in V.110 frame

S3+S4

-

Control signal transmission - C/I

Interface signals

6.5.3

- bit rates 1.2…48 kbit/s

G, T, R, S, C, I

- bit rates 56…n x 64 kbit/s

G, T, R, S

Electrical interface

X.27(V.11)

Connector type

ISO 4903, D-type 15-pin female connector

Transparent 2 Mbit/s, n x 64 kbit/s Interface type

G.703 2 Mbit/s

G.703 64 kbit/s

Optical Line

Line Terminal

Baseband Line

Data bit rate, n x 64 kbit/s

n=32

n=1

n=32

n=17, 32

n x 64 kbit/s n=1…66

The G703-64-M interface is designed for indoor use only. It is not meant for external connections.

6.6 6.6.1

Data Interface Modules 8448 kbit/s, G.703 Interface (G703-8M-M Module)

22030_12 © 2013 Tellabs.

Bit rate

8448 kbit/s ±30 ppm

Coding

HDB3

Nominal impedance

75 Ω

Nominal peak voltage

2.37 V/75 Ω unbalanced

Pulse width

59 ns ±10 ns

Attenuation margin

0…6 dB/4 MHz

Jitter tolerance

G.823

Connector type

50 Ω, SMB-type connector

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 143

6 Technical Specifications of Tellabs 8120 Mini Node M

6.6.2

6.6.3

6.6.4

2048 kbit/s, G.703 Interface (G703-75-M) Bit rate

2048 kbit/s ±50 ppm

Coding

HDB3

Nominal impedance

75 Ω

Nominal peak voltage

2.37 V/75 Ω unbalanced

Pulse width

244 ns ±25 ns

Attenuation margin

0…6 dB/1 MHz

Jitter tolerance

G.823

Connector type

50 Ω, SMB-type connector

2048 kbit/s, G.703 Interface (G703-120-M) Bit rate

2048 kbit/s ±50 ppm

Coding

HDB3

Nominal impedance

120 Ω

Nominal peak voltage

3.0 V/120 Ω balanced

Pulse width

244 ns ±25 ns

Attenuation margin

0…6 dB/1 MHz

Jitter tolerance

G.823

Connector type

D-type 9-pin female connector

2048 kbit/s and 1088 kbit/s Line Terminal Interface (LTE-M Module) Bit rate

2048 kbit/s ±50 ppm

1088 kbit/s ±50 ppm

Coding

HDB3

HDB3

Nominal peak voltage

3.0 V / 120 Ω symmetrical

Pulse width

244 ns ±25 ns

460 ns ±40 ns

Attenuation margin

0…36 dB at 1024 kHz

0…36 dB at 544 kHz

Jitter tolerance

G.823

Mask like G.823 for 2048 kbit/s with the following exceptions: A0: 19.6 (18 µs) A1: 0.75 A2: 0.10 f4: 50 kHz

Input impedance

120 Ω symmetrical

Return loss

G.703

Connector type

D-type 9-pin female connector

Overvoltage protection

Gas discharge tubes, diodes

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 144

22030_12 © 2013 Tellabs.

6 Technical Specifications of Tellabs 8120 Mini Node M

6.6.5

Optical Line Interface 2048 kbit/s / 8448 kbit/s (OTE-LED-M Module) Bit rate

2048 kbit/s ±50 ppm 8448 kbit/s ±30 ppm

Transmission path

Standard multimode fiber (G.651) Standard single mode fiber (G.652)

Optical transmitter

Semiconductor LED

Nominal wave length

1300 nm

Optical line code

CMI

Symbol rate

4096 kBd (2 Mbit/s) 16896 kBd (8 Mbit/s)

Optical receiver Min. sensitivity (BER

PIN diode 10 -9)

-50 dBm (2M) -42 dBm (8M)

Optical connector

FC type with a receptacle

LED safety

EN 60825-1/A2: 2001 (IEC 60825-1 Ed. 1.2, 2001-08)

Functional mode

Minimum output power

Attenuation margin

multimode

LED 2 M

-20 dBm

30 dB

single mode

LED 2 M

-30 dBm

20 dB

multimode

LED 8 M

-20 dBm

22 dB

single mode

LED 8 M

-30 dBm

12 dB

Fig. 79 Class 1 LED Product

6.6.6

Baseband Line Interface 64…384 kbit/s (BTE-384-M Module)

22030_12 © 2013 Tellabs.

Bit rate

N x 64 kbit/s (n=1…6)

Line interface

2/4W full-duplex

Line code

Biphase space

Interface impedance

150 Ω symmetrical

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 145

6 Technical Specifications of Tellabs 8120 Mini Node M

6.6.7

6.7

Output level/150 Ω

0/-6 dBm

Return loss

>12 dB

Maximum input level/150 Ω

0 dBm

Minimum input level/150 Ω

-33 - -38 dBm (varies according to bit rate)

Equalizer

Adaptive

Connector type

D-type 9-pin female connector

Baseband Line Interfaces 320...4224 kbit/s (BTE-1088-M, BTE-2048-M, BTE-2048-2W-M, BTE-4096-M, BTE-320-M, BTE-576-M, BTE-1088-2W-M and BTE-2304-M Modules) Bit rate

n x 64 kbit/s, n=5 (BTE-320-M) n=5, 9 (BTE-576-M) n=5, 9, 16, 17 (BTE-1088-2W-M) n=5, 9, 17 (BTE-1088) n=16, 17, 32, 33 (BTE-2048, BTE-2048-2W-M) n=16, 17, 32, 33, 34, 36 (BTE-2304-M) n=16, 17, 32, 33, 64, 66 (BTE-4096)

Line interface

4 W full-duplex (BTE-1088-M, BTE-2048-M, BTE-4096-M) 2 W full-duplex (BTE-320-M, BTE-576-M) 2 W/4W full-duplex (BTE-2048-2W-M, BTE-1088-2W-M, BTE-2304-M)

Line code

2B1Q

Interface impedance

135 Ω symmetrical

Output level/135 Ω

+13.5 /+6 dBm/0 dBm

Return loss

> 12 dB

Maximum input level/135 Ω

+ 15 dBm

Minimum input level/135 Ω

-15…-30 dBm, varies according to bit rate and transmit level

Equalizer

Adaptive

Connector type

D type 9-pin female connector

Service Computer (SC) Interface Interface type

V.24

Electrical interface

V.28

Data bit rate

9.6 kbit/s asynchronous

Character format

8 bit, no parity, 1 stop bit

Connector type

ISO 2110, D-type 9-pin female connector

Interface signals

102, 103, 104, 105, 106, 107, 108, 109

Protocol

Layers 2…7 proprietary

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 146

22030_12 © 2013 Tellabs.

6 Technical Specifications of Tellabs 8120 Mini Node M

6.8

Power Supply AC Power Supply Input voltage

100...240 V AC ±10% 47…63 Hz

Type number

8990NFS40

DC Power Supply 24 V Input voltage

19…36 V DC, negative pole earthed

Type number

PDU 42238

DC Power Supply 48 V Input voltage

40…60 V DC, positive pole earthed

Type number

PDU 423

Power Consumption Dependent on furnishing, max

6.8.1

38The 39The

< 40 W

Power Consumptions of Tellabs 8120 Mini Node M Units and Modules Unit or Module

Description

Power Consumption (max)

BTE-64-M39

Baseband interface module

2.3 W

BTE-320-M39

T-SDSL interface module

2.2 W

BTE-384-M39

Baseband interface module

2.3 W

BTE-576-M39

T-SDSL interface module

2.2 W

BTE-1088-M39

Baseband interface module

3.0 W

BTE-1088-2W-M39

T-SDSL interface module

2.2 W

BTE-2048-M39

Baseband interface module

3.5 W

BTE-2048-2W-M39

T-SDSL interface module

4.5 W

BTE-2304-M39

T-SDSL interface module

2.2 W

BTE-4096-M39

Baseband interface module

3.5 W

G703-64-M39

G.703 64 kbit/s interface module

1.5 W

G703-75-M

G.703 2 Mbit/s 75-ohm interface module

1.0 W

G703-120-M

G.703 2 Mbit/s 120-ohm interface module

1.0 W

G703-8M-M39

G.703 8 Mbit/s 75-ohm interface module

1.0 W

power supply module has been discontinued. interface module has been discontinued.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 147

6 Technical Specifications of Tellabs 8120 Mini Node M

6.9

Unit or Module

Description

Power Consumption (max)

HSSI-M39

High-Speed Serial interface module

3.9 W

LTE-M39

Line terminal 1/2 Mbit/s

1. 1W

Mini LAN Module

10Base-T Ethernet interface module

2.0 W

OTE-LED-M

Optical line interface module 2/8 Mbit/s

3.7 W

SMU-M

Tellabs 8120 mini M base unit

5.0 W

VCM-M-M

V-series interface base unit

1.5 W

VCM-V-M

VF-series interface base unit

1.0 W

VCM-VM-M

V/VF-series interface base unit

1.5 W

V24-DCE-M39

V.24 interface module

1.5 W

V24-DTE-M39

V.24/V.28 DTE interface module

1.5 W

V35-M

V.35 interface module

1.5 W

V35/V24-M39

V.35/V.24 DCE interface module

1.5 W

V36-M39

V.36 interface module

1.5 W

X21-M

X.21 interface module

1.5 W

Mechanics Width

352 mm

Depth

278 mm

Height

75 mm

Weight, max.

4.5 kg, depends on furnishing

6.10 Environmental Conditions 6.10.1

Climatic/Mechanical Compatibility Tellabs 8120 mini Node (SBM 2048) HW version 6.1 or later Storage

ETS 300 019-1-1:1992-02 Class1.1 Weather protected, partly temperature controlled storage locations -5°C...+45°C

Transport

ETS 300 019-1-2:1992-02 Class2.3 Public transportation -25°C...+70°C Rain is not allowed ; -25°C maximum

In use

ETS 300 019-1-3:1992-02 Class 3.1 Temperature-controlled locations +5°C...+40°C (-5°C…+45°C)

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 148

22030_12 © 2013 Tellabs.

6 Technical Specifications of Tellabs 8120 Mini Node M

6.11 Safety Compatibility Tellabs 8120 mini node (SBM 2048) HW version 6.1 or later Safety

EN 60950-1:2001

When AC power supply is used, Tellabs 8120 mini M must be connected to a wall socket-outlet with protective earth .

When DC power supply is used, Tellabs 8120 mini node M must be permanently connected to earth using the supplied grounding earth wire.

6.12 Electromagnetic Compatibility Tellabs 8120 mini Node (SBM 2048) HW version 6.1 or later EMC

22030_12 © 2013 Tellabs.

EN 300 386:2005

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 149

Appendix 1: Frame Structures

Appendix 1: Frame Structures Frame Structures at Bit Rates 48…2048 Kbit/s Frames Not ing CRC Checking and Plesiochronous Clocking The rate adaptation and multiplexing schemes used in the basic operation mode (no CRC check or independent clocking) are as follows. 48 kbit/s CCITT V.110/X.30 V.110 Rate Adaptation 48 kbit/s → 64 kbit/s Octet no.

Bit no. 1

2

3

4

5

6

7

8

1

1

D1

D2

D3

D4

D5

D6

S1

2

0

D7

D8

D9

D10

D11

D12

X

3

1

D13

D14

D15

D16

D17

D18

S3

4

1

D19

D20

D21

D22

D23

D24

S4

• FSW: 1011 • Dn: data bits • S1, S3: SA =108/107 signal • S4: SB = 105/109 signal • X: X = 106 signal • X.30: SA+SB = C/I (105/109) signal • Frame length: 500 µs 56 kbit/s CCITT V.110 Tables b and c V.110 Rate Adaptation 56 kbit/s → 64 kbit/s Octet no

Bit no. 1

2

3

4

5

6

7

8C

8B

1

D1

D2

D3

D4

D5

D6

D7

0

1

2

D8

D9

D10

D11

D12

D13

D14

X

1

3

D15

D16

D17

D18

D19

D20

D21

S3

1

4

D22

D23

D24

D25

D26

D27

D28

S4

1

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 150

22030_12 © 2013 Tellabs.

Appendix 1: Frame Structures

Octet no

Bit no.

5

D29

D30

D31

D32

D33

D34

D35

1

1

6

D36

D37

D38

D39

D40

D41

D42

1

1

7

D43

D44

D45

D46

D47

D48

D49

1

1

8

D50

D51

D52

D53

D54

D55

D56

1

1

V.110 defines two types of frames at 56 kbit/s. Bit 8 is used as 8B in frame mode 1 (CCITT V.110 table 7b) and as 8C in mode 2 (CCITT V.110 table 7c). • FSW0 - - - 1111 • Dn: data bits • S3: SA =108/107 signal • S4: SB = 105/109 signal • X: X = 106 signal • Frame length: 1 ms 72, 80, 144 and 160 kbit/s Mapping of 72, 80, 144, 160 kbit/s Data rate

64 kbit/s bit no. 1

2

3

8 kbit/s chan no40 4

5

6

7

8

A

B

C

D

-

-

72

D1

D2

D3

D4

D5

D6

D7

D8

D9

-

80

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

-

-

144

D1

D2

D3

D4

D5

D6

D7

D8

D9

-

-

-

D10

D11

D12

D13

D14

D15

D16

D17

-

D18

-

-

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

-

-

D11

D12

D13

D14

D15

D16

D17

D18

-

-

D19

D20

160

• Di: data bits. The index shows sequence order. • The frame length is 125 µs.

Frames ing CRC Checking and Plesiochronous Clocking The rate adaptation and multiplexing schemes ing CRC checking or/and plesiochronous data clocking are shown below. The CRC checking procedure is based on the CRC-4 method used in G.704. The transfer of clock phase and stuffing bits is based on the method in V.110.

40A,

B, C, D: 8 kbit/s channels used to transport the n x 8 kbit/s capacity

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 151

Appendix 1: Frame Structures

48 kbit/s Modified CCITT V.110/X.30 Rate Adaptation of 48 kbit/s → 64 kbit/s when ing CRC Check and Independent Clocking Octet no

Bit no. 1A

1B

1C

2

3

4

5

6

7

8

1

0

0

0

D1

D2

D3

D4

D5

D6

S1

2

X

X

X

D7

D8

D9

D10

D11

D12

X

3

CFE

CFE

1

D13

D14

D15

D16

D17

D18

S3

4

1

1

1

D19

D20

D21

D22

D23

D24

S4

5

0

0

0

D25

D26

D27

D28

D29

D30

S1

6

1

1

1

D31

D32

D33

D34

D35

D36

X

7

1

1

1

D37

D38

D39

D40

D41

D42

S3

8

1

1

1

D43

D44

D45

D46

D47

D48

S4

9

1

1

1

D49

D50

D51

D52

D53

D54

S1

10

E4

1

E4

D55

D56

D57

D58

D59

D60

X

11

E5

1

E5

D61

D62

D63

D64

D65

D66

S3

12

E6

1

E6

D67

D68

D69

D70

D71

D72

S4

13

C1

C1

1

D73

D74

D75

D76

D77

D78

S1

14

C2

C2

1

D79

D80

D91

D82

D83

D84

X

15

C3

C3

1

D85

D86

D87

D88

D89

D90

S3

16

C4

C4

1

D91

D92

D93

D94

D95

D96

S4

56 kbit/s Modified CCITT V.110 Rate Adaptation of 56 kbit/s → 64 kbit/s when ing CRC Check and Independent Clocking Octet no

Bit no. 1

2

3

4

5

6

7

8A

8B

8C

8D

1

D1

D2

D3

D4

D5

D6

D7

0

0

0

0

2

D8

D9

D10

D11

D12

D13

D14

X

X

X

X

3

D15

D16

D17

D18

D19

D20

D21

CFE

CFE

S3

S3

4

D22

D23

D24

D25

D26

D27

D28

S4

S4

S4

S4

5

D29

D30

D31

D32

D33

D34

D35

0

0

0

0

6

D36

D37

D38

D39

D40

D41

D42

1

1

1

1

7

D43

D44

D45

D46

D47

D48

D49

1

1

1

1

8

D50

D51

D52

D53

D54

D55

D56

1

1

1

1

9

D57

D58

D59

D60

D61

D62

D63

1

1

1

1

10

D64

D65

D66

D67

D68

D69

D70

E4

X

E4

X

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 152

22030_12 © 2013 Tellabs.

Appendix 1: Frame Structures

Octet no

Bit no.

11

D71

D72

D73

D74

D75

D76

D77

E5

S3

E5

S3

12

D78

D79

D80

D91

D82

D83

D84

E6

S4

E6

S4

13

D85

D86

D87

D88

D89

D90

D91

C1

C1

1

1

14

D92

D93

D94

D95

D96

D97

D98

C2

C2

1

1

15

D99

D100

D101

D102

D103

D104

D105

C3

C3

1

1

16

D106

D107

D108

D109

D110

D111

D112

C3

C4

1

1

• 8A: both CRC checking and plesiochronous clocking are used • 8B: only CRC checking in use • 8C: only plesiochronous clocking in use • 8D: neither CRC check nor plesiochronous clocking in use • FSW: 0 - - -01111 • Dn: data bits • S3: SA = 108/107 signal • S4: SB = 105/109 signal • X: X = 106 signal • CFE: CRC bit from remote end • Ci: bits for transfer of the CRC word • Ei: bits for transfer of clock phase and stuffing bits • E6: transfers an extra D bit at positive justification inserted between D72 - D73 or D84 - D85 • D73: is set to 1 when performing negative justification • Frame length: 2 ms 72, 80 kbit/s Adaptation of 72 and 80 kbit/s when ing CRC Check and Plesiochronous Clocking Set no

64 kbit/s bit no

8 kbit/s chan41

1

2

3

4

5

6

7

8

A

B

C

1

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

0

2

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

X

3

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

CFE

4

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

S4

5

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

0

6

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

1

418 kbit/s channel no B is not used at 72 kbit/s. Channel C uses a 16-bit long frame carrying the CRC check sum and phasing and stuffing data for plesiochronous clocking.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 153

Appendix 1: Frame Structures

Set no

64 kbit/s bit no

8 kbit/s chan41

7

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

1

8

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

1

9

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

1

10

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

E4

11

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

E5

12

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

E6

13

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

C1

14

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

C2

15

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

C3

16

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

C4

• Set: group of data bits transmitted each 125 µs • FSW: 0 - - -01111 • Dn: data bits • S3: SA = 108/107 signal • S4: SB = 105/109 signal • X: X = 106 signal • CFE: CRC bit from far-end • Ci: bits for transfer of the CRC word • Ei: bits for transfer of clock phase and stuffing bits • E6: transfers an extra D bit at positive justification inserted before bit D1 of set 14 • D8 of set 13: is set to 1 when performing negative justification • Frame length: 2 ms 144, 160 kbit/s Adaptation of 144 and 160 kbit/s when ing CRC Check and Plesiochronous Clocking Set no42

64 kbit/s bit no

8 kbit/s no43

1

2

3

4

5

6

7

8

A

B

1a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

1b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

2a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

2b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

C

D

E

D19

D20

0

D19

D20

X

42The

sets a and b are transmitted during the same G.704 frame (125 µs). kbit/s channels B and D are not used at 160 kbit/s. Channel E uses a 16-bit long frame carrying the CRC check sum and phasing and stuffing data for plesiochronous clocking. 438

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 154

22030_12 © 2013 Tellabs.

Appendix 1: Frame Structures

Set no42

64 kbit/s bit no

8 kbit/s no43

3a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

3b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

4a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

4b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

5a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

5b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

6a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

6b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

7a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

7b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

8a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

8b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

9a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

9b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

10a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

10b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

11a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10 -

11b

D11

D12

D13

D14

D15

D16

D17

D18

-

12a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10 -

12b

D11

D12

D13

D14

D15

D16

D17

D18

-

13a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10 -

13b

D11

D12

D13

D14

D15

D16

D17

D18

-

14a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

14b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

15a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

15b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

16a

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

16b

D11

D12

D13

D14

D15

D16

D17

D18

-

-

D19

D20

CFE

D19

D20

S4

D19

D20

1

D19

D20

1

D19

D20

1

D19

D20

1

D19

D20

1

D19

D20

E4

D19

D20

E5

D19

D20

E6

D19

D20

C1

D19

D20

C2

D19

D20

C3

D19

D20

C4

• FSW: 0 - - -01111 • Dn: data bits • S3: SA = 108/107 signal • S4: SB = 105/109 signal • X: X = 106 signal • CFE: CRC bit from far-end • Ci: bits for transfer of the CRC word • Ei: bits for transfer of clock phase and stuffing bits

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 155

Appendix 1: Frame Structures

• E6: transfers an extra D bit before D1 of set 13a at positive justification • D8 of set 13a: is set to 1 when performing negative justification • Frame length: 2 ms Adaptation of n x 64 kbit/s when ing CRC Check and Plesiochronous Clocking Frame No

8 kbit/s no A

B

C

1

1

0

SB

2

E4

X

SB

3

E5

CFE

SB

4

E6

S4

SB

5

1

0

SB

6

E4

1

SB

7

E5

1

SB

8

E6

1

SB

9

1

1

SB

10

E4

E4

SB

11

E5

E5

SB

12

E6

E6

SB

13

1

C1

SB

14

E4

C2

SB

15

E5

C3

SB

16

E6

C4

SB

The 8 kbit/s channel A carries the clock phasing and justification data at bit rates exceeding 512 kbit/s. When no independent clocking is needed or when bit rates are below 512 kbit/s, channel B is sufficient. If required, the 8 kbit/s channel C is used to carry signal SB transferring signal 105/109 or C/I • FSW: 0 - - -01111 • S4: SB = 105/109 signal • X: X = 106 signal • CFE: CRC bit from far-end • Ci: bits for transfer of the CRC word • Ei: bits for transfer of clock phase and stuffing bits • E6: transfers an extra D bit at positive justification The n x 64 kbit/s data is chopped into bytes. At positive justification the bit E6 is inserted after the last bit of the first byte received in frame 13. A negative justification takes place by deleting the last bit of the first byte received in frame 13.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 156

22030_12 © 2013 Tellabs.

Appendix 1: Frame Structures

Frame Structures at Bit Rates below 48 Kbit/s Bit rates below 48 kbit/s are rate adapted to n x 8 kbit/s (XB rate) according to CCITT Recommendation V.110/X.30. Relation between Data Rates and Adapted XB Rates Data rate

XB rate

1.2 kbit/s

8 kbit/s

2.4 kbit/s

8 kbit/s

9.6 kbit/s

16 kbit/s

19.2 kbit/s

32 kbit/s

38.4 kbit/s

64 kbit/s

The octet structured V.110 frame is 80 bits long.

Rates n x 4.8 kbit/s V.110 Frame for Adaptation of n x 4800 b/s to n x 8 kbit/s Octet no

Bit no 1

2

3

4

5

6

7

8

1

0

0

0

0

0

0

0

0

2

1

D1

D2

D3

D4

D5

D6

S1

3

1

D7

D8

D9

D10

D11

D12

X

3

1

D13

D14

D15

D16

D17

D18

S3

5

1

D19

D20

D21

D22

D23

D24

S4

6

1

E1

E2

E3

E4

E5

E6

E7

7

1

D25

D26

D27

D28

D29

D30

S1

8

1

D31

D32

D33

D34

D35

D36

X

9

1

D37

D38

D39

D40

D41

D42

S3

10

1

D43

D44

D45

D46

D47

D48

S4

• FSW: 000000001…1…1…1…1…1…1…1…1 • Dn: data bits • S1, S3, S6, S8: SA = 108/107 signal • S4, S9: SB = 105/109 signal • X: X = 106 signal • E1-E3: data rate information code • E4-E6: bits for transfer of clock phase information and stuffing bits at plesiochronous operation. They are set to 1 when not used 22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 157

Appendix 1: Frame Structures

• E7: alignment bit for the four frame multiframe (MFSW=1110). E7 is set to 1 when not used • E6: transfers an extra D bit at positive justification. The bit is inserted between D24 and D25 • D25 : is set to 1 when performing negative justification • Frame length: 2.5, 5 or10 ms, depending on bit rate The rates 600, 1200 and 2400 are mapped to the frame of the previously presented table Adaptation of n x 64 kbit/s when ing CRC Check and Plesiochronous Clocking as follows: • Each 600 b/s bit occupies eight consecutive Dn bit positions starting from D1 (e.g. bit 1 = D1+D2+D3+D4+D5+D6+D7+D8) • Each 1200 b/s bit occupies four consecutive Dn bit positions starting from D1 (e.g bit 1 = D1+D2+D3+D4, bit2 = D5+D6+D7+D8) • Each 2400 b/s bit occupies two consecutive Dn bit positions (e.g. bit 1 = D1+D2, bit2 = D3+D4, bit3 = D5+D6). One V.110 frame transfers 6 bits at 600 bit/s, 12 bits at 1200 bit/s and 24 bits at 2400 bit/s.

Rates n x 3.6 kbit/s V.110 Frame for Adaptation of n x 3600 bit/s to n x 8 kbit/s Octet no.

Bit no 1

2

3

4

5

6

7

8

1

0

0

0

0

0

0

0

0

2

1

D1

D2

D3

D4

D5

D6

S1

3

1

D7

D8

D9

D10

F44

F

X

3

1

D11

D12

F

F

D13

D14

S3

5

1

F

F

D15

D16

D17

D18

S4

6

1

E1

E2

E3

E4

E5

E6

E7

7

1

D19

D20

D21

D22

D23

D24

S1

8

1

D25

D26

D27

D28

F

F

X

9

1

D29

D30

F

F

D31

D32

S3

10

1

F

F

D33

D34

D35

D36

S4

Otherwise see the table Rates n x 4.8 kbit/s. D19 corresponds to D25.

44F

= filling bit

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 158

22030_12 © 2013 Tellabs.

Appendix 1: Frame Structures

Rates n x 3.2 kbit/s V.110 Frame for Adaptation of n x 3200 b/s to n x 8 kbit/s Octet no

Bit no 1

2

3

4

5

6

7

8

1

0

0

0

0

0

0

0

0

2

1

D1

D2

D3

D4

D5

D6

S1

3

1

D7

D8

D9

D10

F

F

X

3

1

D11

D12

F

F

D13

D14

S3

5

1

F

F

D15

D16

F

F

S4

6

1

E1

E2

E3

E4

E5

E6

E7

7

1

D17

D18

D19

D20

D21

D22

S1

8

1

D23

D24

D25

D26

F

F

X

9

1

D27

D28

F

F

D29

D30

S3

10

1

F

F

D31

D32

F

F

S4

Rates n x 3.0 kbit/s V.110 Frame for Adaptation of n x 3000 b/s to n x 8 kbit/s Octet no

Bit no 1

2

3

4

5

6

7

8

1

0

0

0

0

0

0

0

0

2

1

D1

D2

D3

D4

D5

D6

S1

3

1

D7

D8

D9

D10

F

F

X

3

1

D11

D12

F

F

D13

D14

S3

5

1

F

F

D15

F

F

F

S4

6

1

E1

E2

E3

E4

E5

E6

E7

7

1

D16

D17

D18

D19

D20

D21

S1

8

1

D22

D23

D24

D25

F

F

X

9

1

D26

D27

F

F

D28

D29

S3

10

1

F

F

D30

F

F

F

S4

Bit Rate Information Code E1-E3 The bit rate information is coded as follows. Bit Information Code E1-E3

22030_12 © 2013 Tellabs.

Bit rate bit/s

E1 E2 E3

600

100

1200

010

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 159

Appendix 1: Frame Structures

Bit rate bit/s

E1 E2 E3

2400

110

4800

011

9600

011

19200

011

38400

011

3600

101

7200

101

14400

101

28800

101

3000

011

6000

011

12000

011

24000

011

3200

001

6400

001

12800

001

25600

001

Use of Clock Phase and Stuffing Information Bits E4-E6 Network independent timing (plesiochronous) is ed at data rates 3000 b/s and above. The E4-E6 bits are used as follows. Clock Phase and Stuffing Information Clock displacement, %

E4 E5 E6

0

111

+20

000

+40

001

-40

010

-20

011

Stuffing control Positive justification of a 1

101

Positive justification of a 0

100

Negative justification

110

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 160

22030_12 © 2013 Tellabs.

Appendix 1: Frame Structures

Modified V.110 Frame for Transfer of CRC Check Sum Octet no

Bit no 1

2

3

4

5

6

7

8

1

0

0

0

0

0

0

0

0

2

1

D1

D2

D3

D4

D5

D6

S1

3

1

D7

D8

D9

D10

D11

D12 X

3

1

D13

D14

D15

D16

D17

D18

S3

5

1

D19

D20

D21

D22

D23

D24

S4

6

CFE

E1

E2

E3

E4

E5

E6

E7

7

C1

D25

D26

D27

D28

D29

D30

S1

8

C2

D31

D32

D33

D34

D35

D36

X

9

C3

D37

D38

D39

D40

D41

D42

S3

10

C4

D43

D44

D45

D46

D47

D48

S4

• FSW: 000000001…1…1…1 • Dn: data bits • S1, S3: SA = 108/107 signal • S4: SB = 105/109 signal • X: X = 106 signal • E1-E3: data rate information code • E4-E6: bits for transfer of clock phase information and stuffing bits at plesiochronous • CFE: CRC check sum indication to the far-end • Ci: CRC check sum • F: filling bits (not shown) are used for adaptation of n x 3600, n x 3000 and n x 3200 b/s to n x 8 kbit/s as in the tables of the Frame Structures at Bit Rates below 48 Kbit/s presented earlier in Appendix 1.

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 161

Appendix 2: G.704 Frame Structures

Appendix 2: G.704 Frame Structures 8448 kbit/s Frame Structure

Fig. 80 Frame Structure of G.704 8448 kbit/s Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 162

22030_12 © 2013 Tellabs.

Appendix 2: G.704 Frame Structures

2048 kbit/s Frame Structure

Fig. 81 Frame Structure of G.704 2048 kbit/s

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 163

Appendix 2: G.704 Frame Structures

N x 64 kbit/s Frame Structure

Fig. 82 Frame Structure of G.704 n x 64 kbit/s; n ≤ 17

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 164

22030_12 © 2013 Tellabs.

Appendix 2: G.704 Frame Structures

Fig. 83 Frame Structure of G.704 n x 64 kbit/s; n > 17

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 165

Appendix 2: G.704 Frame Structures

Multiframe Structure in Signalling Time Slot (8 Mbit/s frame TS67, 68, 69, 70. 2 Mbit/s frame and n x 64 kbit/s frame with n >17 TS16. N x 64 kbit/s frame with n≤17 TSn-1.) SigTSbits1234abcd

SigTSbits5678abcd

Use

0

0000

SASS

0000=M-FSW, A=FEA (1-active), S=spare

1

TS1

TS17

abcd bits for TS1 and TS17 of the group

2

TS2

TS18

.

3

TS3

TS19

.

4

TS4

TS20

.

5

TS5

TS21

.

6

TS6

TS22

.

7

TS7

TS23

.

8

TS8

TS24

.

9

TS9

TS25

.

10

TS10

TS26

.

11

TS11

TS27

.

12

TS12

TS28

.

13

TS13

TS29

.

14

TS14

TS30

.

15

TS15

TS31

abcd bits for TS15 and TS31 of the group

45Frame

45Multiframe

#

length is 16 frames/125 µs = 2 ms (500 Hz)

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 166

22030_12 © 2013 Tellabs.

Appendix 2: G.704 Frame Structures

CRC Multiframe Structure in TS0 for 2 Mbit/s and n x 64 kbit/s Frames TS0 bits1

2345678

Use

0

C1

0011011

46C1…C4

1

0

1ASHHHH

A = FEA (1-active), S = spare

2

C2

0011011

0011011 = FSW, H = reserved for the HDLC link

3

0

1ASHHHH

001011 = CRC M-FSW

4

C3

0011011

5

1

1ASHHHH

6

C4

0011011

7

0

1ASHHHH

8

C1

0011011

9

1

1ASHHHH

10

C2

0011011

11

1

1ASHHHH

12

C3

0011011

13

E1

1ASHHHH

14

C4

0011011

15

E2

1ASHHHH

Frame # Block #1

= CRC-4 bits

Block #2

46The

E1 = BlockI FEA (0-active)

E2 = BlockII FEA (0-active)

CRC multiframe length is 16 frames/125 µs = 2 ms (500Hz)

22030_12 © 2013 Tellabs.

Tellabs ® 8100 Managed Access System Tellabs ® 8120 Mini Node M Operating Manual 167