Introduction The Blade® 450 3D will give intermediate to advanced heli pilots an outdoor ready-to-fly experience like no other. It comes out of the box 100% factory built and equipped with state-of-the-art features like brushless power, digital servos, a MEMS heading lock gyro, CM control and symmetrical Blades. Its new and improved digital cyclic and tail servos provide crisper, cleaner response for added precision and stability while the new heading lock gyro provides more control over the tail for additional control and confidence. And because it’s flight tested at the factory, no pre-flight setup is required. The Blade 450 3D is ready for everything from smooth hovering to 3D aerobatic flying as soon as you finish charging the battery included with the RTF, or bind to your DSM transmitter if purchasing the BNF Basic. The 450 3D’s new aggressive body and trim scheme make this Blade one hot heli.
Table of Contents
Blade 450 3D Specifications
Charging the Flight Battery............................................................................ 4 Low Voltage Cutoff (LVC)................................................................................ 4 Throttle Hold.................................................................................................. 4 Transmitter and Receiver Binding................................................................... 5 Installing the Flight Battery............................................................................ 5 Gyro Test....................................................................................................... 6 Motor Control Test.......................................................................................... 6 Flying the Blade 450 3D................................................................................. 7 Gyro Gain Adjustment.................................................................................... 7 Post-Flight Inspections and Maintenance....................................................... 7 Throttle Curve and Pitch Curve...................................................................... 8 Intermediate.................................................................................................. 8 Advanced...................................................................................................... 8 FCC Information............................................................................................. 8 Warranty and Repair Policy............................................................................ 9 Warranty and Service Information..................................................... 9 Customer Service Information...................................................................... 10 Compliance Information for the European Union........................................... 10
25.8 in (655mm)
Length Height
9.3 in (235mm)
Main Rotor Diameter
28.4 in (721mm)
Tail Rotor Diameter
5.6 in (142mm)
Gross Weight
26.9 oz (762 g) Components
Motor
420H Brushless outrunner, 3800Kv (installed)
ESC
35-amp brushless (installed)
Battery
3S 11.1V 2200mAh 30C Li-Po (included with RTF)
Charger
DC Li-Po Balancing Charger (included with RTF)
Transmitter
Spektrum DX6i 6-channel Computer Radio with AA Batteries (included with RTF)
Receiver
Spektrum AR6115e Microlite 6 Channel Receiver (installed)
Swash Servos
DS76 (installed)
Tail Servo
DS76T (installed)
Gyro
G210 MEMS Micro Heading Lock (installed)
To your product online, visit www.bladehelis.com
3
EN
Charging the Flight Battery DC Li-Po Balancing Charger Features
The Blade 450 3D RTF comes with a DC balancing charger and 3S Li-Po battery. You must charge the included Li-Po battery pack with a Li-Po specific charger only (such as the included charger). Never leave the battery and charger unattended during the charge process. Failure to follow the instructions properly could result in a fire. When charging, make certain the battery is on a heat-resistant surface. Charge the flight battery before binding the aircraft (BNF only) or performing control tests.
• Charges 3-cell lithium polymer battery packs • 1.8A charge rate • LED charge status indicator • LED cell balance indicator • 12V alligator clip input cord Specifications • Input power: 12V DC, 1.8-amp • Charges 3-cell Li-Po packs with minimum capacity of 1800mAh 3S 11.1V 2200mAh Li-Po Battery Pack The Blade 450 3D 3S Li-Po battery pack features a balancing lead that allows you to safely charge your battery pack when used with the included Blade 450 3D Li-Po balancing charger.
The Battery Charging Process 1.
Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.g., swollen, bent, broken or punctured.
2.
Connect the charger to a 12V power source noting proper polarity.
3.
The CELL STATUS LEDs glow solid red and the CHARGE STATUS LED flashes red.
4.
Connect the battery balance lead to the charger. The balance connector is keyed to prevent reverse polarity.
5.
The CELL STATUS LEDs glow solid green or yellow and the CHARGE STATUS LED glows solid red when the battery is charging.
6.
Charging is complete when all LEDs glow solid red.
7.
Always unplug the battery from the charger immediately upon completion of charging.
CAUTION: Overcharging a battery can cause a fire.
Note: Attempting to charge an over-discharged battery will cause the charger to repeatedly flash red and green, indicating an error has occured. WARNING: Failure to use the proper charger for a Li-Po battery can result in serious damage, and will cause a fire. ALWAYS use caution when charging Li-Po batteries. WARNING: Selecting a charge rate higher than 1x (one times) the battery capacity may cause a fire.
Low Voltage Cutoff (LVC) Repeatedly flying the helicopter until LVC activates will damage the helicopter battery. We recommend using the timer and landing after 6 minutes of flying to prevent damage to the battery. If using the Advanced setting, the timer is programmed for 5 minutes.
The ESC will continuously lower power to the motor until complete shutdown when the battery reaches 9V under load. This helps prevent over-discharge of the Li-Po battery. Land immediately when the ESC activates LVC. Continuing to fly after LVC can damage the battery, cause a crash or both. Crash damage and batteries damaged due to over-discharge are not covered under warranty.
Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. Please fully charge and store a Li-Po battery. During storage make sure battery charge does not go below 3V per cell.
The DX6i timer is programmed for 6 minutes at the factory. The timer can be increased to 8 minutes if you are only hovering the helicopter.
Throttle Hold Throttle hold only turns off the motor on an electric helicopter. You maintain pitch and direction control. The blades will spin if throttle hold is OFF (0). For safety, turn throttle hold ON (1) any time you need to touch the helicopter or check the direction controls. Throttle hold is also used to turn off the motor if the helicopter is out of control, in danger of crashing, or both. Please refer to your transmitter manual for more information on programming throttle hold.
EN
4
Transmitter and Receiver Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ DSM technology equipped aircraft transmitter to the receiver for proper operation. Note: When using a Futaba transmitter with a Spektrum DSM module, you must reverse the throttle channel.
Binding Procedure 1.
Read transmitter instructions for binding to a receiver (location of transmitter’s Bind control).
2.
Make sure transmitter is powered off.
3.
Install a bind plug in the receiver battery/bind port.
4.
Connect the flight battery to the ESC. The receiver LED will begin to flash rapidly.
5.
Move the transmitter controls to neutral (flight controls: rudder, elevators and ailerons) or to low positions (throttle).*
6.
Power on the transmitter while holding the transmitter bind button or switch. Refer to your transmitter’s manual for binding button or switch instructions.
7.
When the receiver binds to the transmitter, the receiver light will turn solid.
8.
Disconnect the flight battery from the ESC. Remove the bind plug from the receiver.
9.
Safely store the bind plug (some owners attach the bind plug to their transmitter using two-part loops and clips).
10. The receiver will keep the binding to the transmitter until another binding is done. * The throttle will not arm if the transmitter’s throttle trim is not at the center position. If you encounter problems, obey binding instructions and refer to transmitter troubleshooting guide for other instructions. If needed, the appropriate Horizon Product office. For a list of compatible DSM transmitters, please visit www.bindnfly.com.
Installing the Flight Battery
:05 SEC :05 SEC
1. Power on transmitter. 2. Lower throttle and center throttle trim. 4. Install flight battery in battery tray. Secure flight battery with hook and loop strap. Connect battery cable to the ESC. WARNING: To keep rotors from initiating at startup, activate throttle hold before connecting flight battery. Note: The power lead must be positioned away from the elevator servo. 3. Attach hook material to the battery and loop material to the helicopter 5. Wait 5 seconds while gyro initializes. frame. 6. Aircraft will emit 2 tones and emit a solid LED on the gyro once it is ready. NOTICE: Always disconnect the Li-Po from the ESC of the aircraft when not flying. Failure to do so will render the battery unusable. Note: Keep helicopter still after connecting flight battery to let helicopter gyroscope calibrate. Do not allow the battery to touch the motor or the elevator servo.
5
EN
Gyro Test 1. Connect the aircraft battery to the ESC. NOTICE: Do not allow the helicopter to move until the red gyro LED is solid. The gyro will not operate correctly if the helicopter moves before the LED is solid red. 2. Move the TH HOLD switch to the (1) position. 3. Move the rudder control to the right. The tail rotor blades move as shown. If they do not move as shown, reverse the rudder channel in the transmitter (refer to your transmitter manual for instructions). 4. Release the rudder control. Quickly turn the helicopter nose to the left. The tail blades move in the same direction as right rudder input. If they do not move as shown, change the position of the reverse switch on the gyro.
Motor Control Test Place the helicopter on a clean and flat ground surface (concrete or asphalt) free of obstructions. Always stay clear of the moving rotor blades. CAUTION: Keep pets and other animals away from the helicopter. Animals may injure themselves if they attack or run toward the helicopter. 1. Move all transmitter switches to the (0) position and move the throttle stick to idle/low stick position.. 2. Turn the transmitter on. Make sure the transmitter shows at least 5.0V on the screen. CAUTION: The transmitter battery alarm beeps when the transmitter batteries are 4.3V or less. Replace the transmitter batteries when the alarm beeps. 3. Connect the blue EC3™ battery connector to the ESC. Do not allow the helicopter to move until the red LED on the gyro is solid. 4. The motor beeps twice when the ESC arms properly. Move the Throttle Hold (TH HOLD) switch to the (1) position. WARNING: The motor, main rotor and tail rotor will spin when the throttle is increased if the TH HOLD switch is not moved to the (1) position. 5. Place the helicopter in an open area outdoors. CAUTION: Stay at least 30 feet (10 meters) away from the helicopter when the motor is running. Do not attempt to fly the helicopter at this time. Move the Throttle Hold switch to the (0) position. Slowly increase the throttle until the blades begin to spin. The main blades spin clockwise when viewing the helicopter from the top. The tail rotor blades spin counterclockwise when viewing the helicopter from the right-hand side. NOTICE: If both the main rotor and tail rotor blades are spinning backward, reduce the throttle to idle. Move the throttle hold switch to the (1) position. Disconnect the battery from the helicopter and reverse any two motor wire connections to the ESC.
MODE 2
EN
6
MODE 1
Flying the Blade 450 3D
0
50 100
Always keep vehicle in sight and under control.
Always turn on throttle hold at rotor strike.
Always use fully charged batteries.
Always keep transmitter powered on while vehicle is powered.
Never operate vehicle with damaged wiring.
Always remove batteries before disassembly.
Always keep moving parts clean.
Always keep parts dry.
Always let parts cool after use before touching.
Always remove batteries after use.
Never touch moving parts.
CAUTION: Always fly the helicopter with your back to the sun and the wind to prevent loss of flight control.
Consult local laws and ordinances before choosing a location to fly your aircraft. Select a large, open area away from people and objects. Your first flights should be outdoors in low-wind conditions. Always stay at least 30 feet (10 meters) away from the helicopter when it is flying.
Continue making trim adjustments until the helicopter hovers at a low altitude with very little drifting and directional control input. If the 450 3D is your first helicopter model, seek help from an experienced pilot to trim the model for you before making your first flight.
The Blade 450 3D is not intended to be flown indoors where it might be possible to fly a Blade SR or Blade CX2. Experienced pilots may find it possible to fly the helicopter in a large gymnasium. CAUTION: Please take a few minutes to familiarize yourself with the Blade 450 3D primary controls before attempting your first flight. The Blade 450 3D is more responsive than other Blade helicopters, such as the Blade SR. We recommend getting help from an experienced pilot and installing training gear if you are new to 3D or collective pitch helicopters.
When the helicopter is in stunt mode: - The rotor head speed is constant. - The main rotor will increase negative pitch as the throttle/collective stick is moved from the middle stick position to the low stick position. Negative pitch allows the helicopter to fly upside down and perform aerobatics. Change between stunt and idle up modes in a hover with the throttle near the middle stick position. The helicopter may go up or down when you change between modes due to the difference in the throttle and pitch curves.
hile attempting to establish a low-level hover, you can also check to see if W any trim adjustments are required to help keep the 450 3D from constantly drifting in various directions. If you find the aircraft constantly drifts without any directional control input, land the model before making any adjustments to the trim settings.
WARNING: Do not use EFLH1415A Main Blades with the Blade 450 or injury and/or property damage could occur.
- If the helicopter drifts forward or backward, adjust the elevator trim. - If the helicopter drifts to the left or right, adjust the aileron trim.
Gyro Gain Adjustment • If the tail wags or oscillates, lower the gain on the gyro. On your transmitter, decrease the gyro gain values a small amount at a time until the helicopter is stable within a particular flight mode • If the tail is drifting while hovering, increase the gain on the gyro. On your transmitter, increase the gyro gain values a small amount at a time until the tail starts to wag/oscillate. Afterwards, reduce the gain until the tail stops wagging/oscillating within a particular flight mode.
Pirouette speed adjustment • To increase or decrease the pirouette rate of the helicopter, adjust the Travel Adjust or Dual Rates values on the rudder channel. Refer to your transmitter’s instruction manual.
Post-Flight Inspections and Maintenance Ball Links
Make sure the plastic ball link holds the control ball, but is not tight (binding) on the ball. When a link is too loose on the ball, it can separate from the ball during flight and cause a crash. Replace worn ball links before they fail.
Cleaning
Make sure battery is not connected before cleaning. Remove dust and debris with a soft brush or a dry lint free cloth.
Bearings
Replace bearings when they become notchy (sticky in places when turning) or draggy.
Wiring
Make sure wiring does not block moving parts. Replace damaged wiring and loose connectors.
Fasteners
Make sure there are no loose screws, other fasteners or connectors. Do not over tighten metal screws in plastic parts. Tighten screw so parts are mated together, then turn screw only 1/8th of a turn more.
Rotors
Make sure there is no damage to rotor blades and other parts which move at high speed. Damage to these parts includes cracks, burrs, chips or scratches. Replace damaged parts before flying.
7
EN
RTF Throttle Curve and Pitch Curve Copying Model Memory 9 or 10 to Model Memory 1 allows you to change between the Intermediate and Advanced flight profiles without re-binding.
There are 2 flight profiles pre-programmed in the included DX6i transmitter. There is an intermediate flight profile and an advanced profile. In the factory configuration, the transmitter is programmed with the intermediate profile loaded. The Blade 450 is bound to Model 1 from the factory. PITCH CURVE
100% The Intermediate Profile is loaded in Model Memory 1 and 9.
If you are just hovering or learning to hover, feel free to add 2 minutes to the timerTHROTTLE (see the CURVE DX6i manual). PITCH CURVE
+9.8°
100%
The Advanced Profile is loaded 72.5% in Model Memory 10
POWER OUTPUT
-1.2°
Note: When using this setup, your helicopter may experience restriction at maximum control throws. Avoid using maximum pitch and cyclic inputs simultaneously. -12° 0%
To load the Intermediate Profile: Copy sub-trim values from Model0%1 to Model 9. Copy Low Model 9 to Model 1. Half High Low STICK POSITION
If you want to get the absolute maximum performance out of your Blade 450 0° 3D, increase the AILE and ELEV50% swash mix values by approximately 10%.
2°
PITCH RANGE
POWER OUTPUT
To load the Advanced Profile: Copy sub-trim values from Model50% 1 to Model 10. Copy Model 10 to Model 1.
Half
High
Low
STICK POSITION
Intermediate
+12°
(The pitch range in the intermediate profile is +/- 10 degrees. It is +/- 12 degrees in the advanced profile). PITCH RANGE
THROTTLE CURVE
Half
High
Low
STICK POSITION
Normal
Half
High
STICK POSITION
Stunt
THROTTLE CURVE
PITCH CURVE
100%
THROTTLE CURVE
+8.2°
PITCH CURVE
100%
+10°
72.5%
72.5%
Low
Half
0% High
-1°
Low
STICK POSITION
Half
High
50%
Low
STICK POSITION
Half
0% High
0°
PITCH RANGE
POWER OUTPUT
50%
PITCH RANGE
POWER OUTPUT
2°
Low
STICK POSITION
Half
-10° High
STICK POSITION
Advanced Normal
Stunt
THROTTLE CURVE
PITCH CURVE
100%
THROTTLE CURVE
+9.8°
PITCH CURVE
100%
+12°
72.5%
Half
0% High
Low
STICK POSITION
THROTTLE CURVE
POWER OUTPUT
FCC Information
Half
High
Low
STICK POSITION
PITCH CURVE
100%
50%
Half
0% High
0°
PITCH RANGE
POWER OUTPUT
-1.2°
Low
STICK POSITION
THROTTLE CURVE
+8.2°
Half
-12° High
STICK POSITION
PITCH CURVE
100%
+10°
72.5%
72.5% 2°
POWER OUTPUT
Low
PITCH RANGE
POWER OUTPUT
2° 50%
PITCH RANGE
PITCH RANGE
50% 50% This device complies with part 15 of the FCC rules. Operation is subject to-1°the following two conditions: (1) This device may not cause harmful interference,0°and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the ’s authority to operate the equipment.
0% 0% This product contains a radio transmitter withLow wireless technology which has been testedLowand found to be Low Half High Half High Half High compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
STICK POSITION
EN
STICK POSITION
STICK POSITION
8
Low
Half
STICK POSITION
-10° High
Warranty and Repair Policy WARRANTY SERVICES Questions, Assistance, and Repairs: Your local hobby store and/or place of purchase cannot provide warranty or repair. Once assembly, setup or use of the Product has been started, you must Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please direct your email to
[email protected], or call 877.504.0233 toll free to speak to a Product representative. You may also find information on our website at www.horizonhobby.com.
Warranty Period: Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase by the Purchaser. Limited Warranty: Horizon reserves the right to change or modify this warranty without notice and disclaims all other warranties, express or implied. (a) This warranty is limited to the original Purchaser (“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those Products purchased from an authorized Horizon dealer. Third party transactions are not covered by this warranty. Proof of purchase is required for all warranty claims.
Inspection or Repairs: If this Product needs to be inspected or repaired, please use the Horizon Online Repair Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Repair Request is available at www.horizonhobby.com under the Repairs tab. If you do not have internet access, please Horizon Product to obtain a RMA number along with instructions for submitting your product for repair. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
(b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE. (c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon will, at its option, (i) repair or (ii) replace, any Product determined by Horizon to be defective. In the event of a defect, these are the Purchaser’s exclusive remedies. Horizon reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Horizon. Return of any Product by Purchaser must be approved in writing by Horizon before shipment.
Notice: Do not ship batteries to Horizon. If you have any issue with a battery, please the appropriate Horizon Product office.
Damage Limits: HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the accepts all resulting liability.
Warranty Inspection and Repairs: To receive warranty service, you must include your original sales receipt ing the proof-of-purchase date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon. Non-Warranty Repairs: Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for repair you are agreeing to payment of the repair without notification. Repair estimates are available upon request. You must include this request with your repair. Non-warranty repair estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashiers checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for inspection or repair, you are agreeing to Horizon’s and Conditions found on our website under the Repairs tab.
If you as the Purchaser or are not prepared to accept the liability associated with the use of this Product, you are advised to return this Product immediately in new and unused condition to the place of purchase. Law: These are governed by Illinois law (without regard to conflict of law principals).
Warranty and Service Information Country of Purchase
Horizon Hobby
Address
Phone Number / Email Address
Horizon Service Center (Electronics and engines)
4105 Fieldstone Rd Champaign, Illinois 61822 USA
877-504-0233 Online Repair Request visit: www.horizonhobby.com/repairs
Horizon Product (All other products)
4105 Fieldstone Rd Champaign, Illinois 61822 USA
877-504-0233
[email protected]
United Kingdom
Horizon Hobby Limited
Units 1-4 Ployters Rd Staple Tye Harlow, Essex CM18 7NS United Kingdom
+44 (0) 1279 641 097
[email protected]
Horizon Technischer Service
Hamburger Str. 10 25335 Elmshorn
+49 4121 46199 66
[email protected]
Horizon Hobby SAS
14 Rue Gustave Eiffel Zone d’Activité du Réveil Matin 91230 Montgeron
+33 (0) 1 60 47 44 70
[email protected]
United States of America
9
EN
Customer Service Information Country of Purchase
Horizon Hobby
Address
Phone Number / Email Address
Sales
4105 Fieldstone Rd Champaign, Illinois 61822 USA
(800) 338-4639
[email protected]
United Kingdom
Horizon Hobby Limited
Units 1-4 Ployters Rd Staple Tye Harlow, Essex CM18 7NS United Kingdom
+44 (0) 1279 641 097
[email protected]
Horizon Hobby GmbH
Hamburger Str. 10 25335 Elmshorn
+49 4121 46199 60
[email protected]
Horizon Hobby SAS
14 Rue Gustave Eiffel Zone d’Activité du Réveil Matin 91230 Montgeron
+33 (0) 1 60 47 44 70
[email protected]
United States
Compliance Information for the European Union AT
BG
CZ
CY
DE
DK
ES
FI
FR
GR LU
HU
IE
IT
LT
LV
MT
NL
PL
PT
RO
SE
SI
SK
UK
Declaration of Conformity
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
(in accordance with ISO/IEC 17050-1)
No. HH20101229011
No. HH2011010903
Product(s): Blade 450 3D RTF Item Number(s): BLH1600 Equipment class: 2
Product(s): Item Number(s): Equipment class:
Blade 450 3D BNF Basic BLH1650 1
The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC:
The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC:
EN 300-328 EN 301 489-1, 301 489-17 EN 301 489-1, 301 489-3 EN 60950
EN 301 489-1, 301 489-17 EN 301 489-1, 301 489-3
Signed for and on behalf of: Horizon Hobby, Inc. Champaign, IL USA December 29, 2010
Technical requirements for Radio equipment. General EMC requirements Safety
General EMC requirements
Signed for and on behalf of: Horizon Hobby, Inc. Champaign, IL USA January 09, 2011 Steven A. Hall Vice President International Operations and Risk Management Horizon Hobby, Inc.
Steven A. Hall Vice President International Operations and Risk Management Horizon Hobby, Inc.
Instructions for disposal of WEEE by s in the European Union This product must not be disposed of with other waste. Instead, it is the ’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please your local city office, your household waste disposal service or where you purchased the product.
EN
10
Spektrum DX6i Intermediate/fortgeschrittene Anfänger/Intermédiaire/Intermedio ADJUST LIST
SETUP LIST Model Type HELI
Swash Type CM 120
Reverse THRO - N
Timer Type - Down
AILE - R
Time - 6:00
ELEV - N
Switch - Trainer
RUDD - R GYRO - N
D/R & Expo
Travel Adj
0-AILE
50%
+7%
THRO
100%
0-ELEV
50%
+7%
ELEV
100%
0-RUDD
77%
INH
GYRO
100%
1-AILE
75%
+15%
AILE
100%
1-ELEV
75%
+15%
RUDD
90%
1-RUDD
77%
INH
PITC
100%
Thro Curve
PITC - N Gyro Rate:
SW-F.Mode
Swash Mix AILE -100%
0: 77.5%
NORM 0
ELEV
-95%
1: 76.0%
STUNT 1
PITC
+85%
Pitc Curve
NORM
0%
56.5% 72.5% 72.5% 72.5%
NORM
45%
51%
60%
73.5% 91%
STUNT
72.5% 72.5% 72.5% 72.5% 72.5%
STUNT
0%
25%
50%
75% 100%
HOLD
10%
HOLD
42%
46%
50%
75% 100%
10%
10%
10% 10%
Advanced/erfahrene Piloten/Avancé/Avanzato ADJUST LIST
SETUP LIST Model Type HELI
Swash Type CM 120
Reverse THRO - N
Timer Type - Down
AILE - R
Time - 5:00
ELEV - N
Switch - Trainer
RUDD - R GYRO - N
Travel Adj
0-AILE
75%
+15%
THRO
100%
0-ELEV
75%
+15%
ELEV
100%
0-RUDD
87%
INH
GYRO
100%
1-AILE
100%
15%
AILE
100%
1-ELEV
100%
15%
RUDD
90%
1-RUDD
87%
INH
PITC
100%
Thro Curve
PITC - N
IT
D/R & Expo
Gyro Rate:
SW-F.Mode
Swash Mix AILE -100%
0: 77.5%
NORM 0
ELEV
-95%
1: 76.0%
STUNT 1
PITC
+92%
Pitc Curve
NORM
0%
56.5% 72.5% 72.5% 72.5%
NORM
45%
51%
60%
73.5% 91%
STUNT
100% 100% 100% 100% 100%
STUNT
0%
25%
50%
75% 100%
HOLD
10%
HOLD
42%
46%
50%
75% 100%
38
10%
10%
10% 10%
Spektrum DX7 / DX7se Intermediate/fortgeschrittene Anfänger/Intermédiaire/Intermedio ADJUST LIST
SETUP LIST Model Type HELI
Swash Type CM 120
Reverse THRO-N
D/R & Expo
Timer Type - Down
ELEV-R GYRO-R AILE-R
Travel Adj
0-AILE
50%
+7%
THRO
100%
0-ELEV
50%
+7%
ELEV
100%
0-RUDD
77%
INH
GYRO
100%
AILE
100%
RUDD
90%
PITC
100%
Time - 6:00
1-AILE
75%
+15%
Switch - Trainer
1-ELEV
75%
+15%
1-RUDD
77%
INH
RUDD-N PITC-N
Thro Curve Gyro Rate:
Pitc Curve
NORM
0%
57%
73%
73% 73%
NORM
45%
51%
60%
74% 91%
-100%
STUNT
73%
73%
73%
73% 73%
STUNT
0%
25%
50%
75% 100%
ELEV
-100%
HOLD
-5%
-5%
-5%
-5% -5%
HOLD
42%
46%
50%
75% 100%
PITC
-84%
SW-F.Mode
Swash Mix AILE
AUTO
NORM
0
0: 77%
STUNT 1
1: 76%
HOLD 0
Advanced/erfahrene Piloten/Avancé/Avanzato ADJUST LIST
SETUP LIST Model Type HELI
Swash Type CM 120
Reverse THRO-N
Timer Type - Down
ELEV-R GYRO-R AILE-R
D/R & Expo
Travel Adj
0-AILE
75%
+15%
THRO
100%
0-ELEV
75%
+15%
ELEV
100%
0-RUDD
87%
INH
GYRO
100%
AILE
100%
RUDD
90%
PITC
100%
Time - 5:00
1-AILE
100%
15%
Switch - Trainer
1-ELEV
100%
15%
1-RUDD
87%
INH
RUDD-N PITC-N
Thro Curve
Pitc Curve
NORM
0%
57%
NORM
45%
51%
60%
74% 91%
STUNT
100% 100% 100% 100% 100%
STUNT
0%
25%
50%
75% 100%
-5%
HOLD
0%
25%
50%
75% 100%
Gyro Rate:
SW-F.Mode
Swash Mix AILE -100%
0: 77.5%
NORM 0
ELEV
-100%
HOLD
1: 76.0%
STUNT 1
PITC
-100%
Thro Hold Switch:
39
-5%
73% -5%
73% 73% -5% -5%
RUDD D/R
IT
Spektrum DX8 Intermediate/fortgeschrittene Anfänger/Intermédiaire/Intermedio ADJUST LIST
SETUP LIST Model Type HELI
Swash Type 3 Servos 120
Reverse THRO-N
Timer 6:00
ELEV-N GYRO-N AILE-N RUDD-N PITC-R Gyro NORM
56.0%
Swash Mix AILE -80%
ST-1
54.5%
ELE
-80%
ST-2
54.5%
PIT
-56%
HOLD
56.0%
Ch: Gear
Sw: F Mode
D/R & Expo
Travel Adj
0-AILE
50%
7%
THRO
100%
0-ELEV
50%
7%
AILE
100%
0-RUDD
77%
0%
ELEV
100%
RUDD
90%
GYRO
100%
PITC
100%
1-AILE
75%
15%
1-ELEV
75%
15%
1-RUDD
77%
0%
2-AILE
75%
15%
2-ELEV
75%
15%
2-RUDD
77%
0%
Thro Curve
Pitc Curve
NORM
0%
57%
73%
73% 73%
NORM
45%
51%
60%
74% 91%
ST-1
73%
73%
73%
73% 73%
ST-1
0%
25%
50%
75% 100%
ST-2
73%
73%
73%
73% 73%
ST-2
0%
25%
50%
75% 100%
HOLD
10%
10%
10%
10% 10%
HOLD
42%
46%
50%
75% 100%
Advanced/erfahrene Piloten/Avancé/Avanzato ADJUST LIST
SETUP LIST Model Type HELI
Swash Type 3 Servos 120
Reverse THRO-N
Timer 5:00
AILE-R ELEV-R RUDD-R GYRO-N PITC-N
IT
Gyro NORM
56.0%
Swash Mix AILE -80%
ST-1
54.5%
ELE
-80%
ST-2
54.5%
PIT
-85%
HOLD
56.0%
Ch: Gear
Sw: F Mode
D/R & Expo
Travel Adj
0-AILE
75%
15%
THRO
100%
0-ELEV
75%
15%
AILE
100%
0-RUDD
87%
0%
ELEV
100%
RUDD
90%
GYRO
100%
PITC
100%
1-AILE
100%
15%
1-ELEV
100%
15%
1-RUDD
87%
0%
2-AILE
100%
15%
2-ELEV
100%
15%
2-RUDD
87%
0%
Thro Curve
Pitc Curve
NORM
0%
NORM
45%
51%
60%
74% 91%
ST-1
100% 100% 100% 100% 100%
ST-1
0%
25%
50%
75% 100%
ST-2
100% 100% 100% 100% 100%
ST-2
0%
25%
50%
75% 100%
HOLD
10%
HOLD
0%
25%
50%
75% 100%
40
57%
10%
73%
10%
73% 73%
10% 10%
Optional Parts / Optionale Bauteile / Pièces optionnelles / Pezzi opzionali Part #
English
Deutsch
Françias
Italiano
BLH1608
Dampeners 80 (4): B450
Dämpfer 80 (4): B450
B450 : Amortisseurs 80 (4)
Gommino ammortizzatore 80 (4): B450
BLH1615C
325mm Carbon Fiber Main Rotor Blade Set: B450, B400
325mm Carbon Hauptrotorblätterset: B450, B400
B450, B400 : Paire de pales principales carbone 325mm
Set pale rotore principale in carbonio da 325mm: B450, B400
BLH1617A
Aluminum Main Rotor Blade Grip Set with Arms: B450
Aluminium Rotorblatthalter mit Anlenkungen:B450
B450 : Set Pieds de pales principales et bras en aluminium
o alluminio per pale rotore con bracci: B450
BLH1623A
Aluminum Flybar Seesaw Holder Set: B450, B400
Aluminium Paddelstangenhalter Set: B450, B400
B450, B400 set de moyeu de barre de Bell en aluminium
Set o alluminio barra stabilizzatore: B450, B400
BLH1624A
Aluminum Flybar Paddle Control Frame Arm Set: B450, B400
Aluminium Paddelanlenkhebel: B450, B400
B450, B400 : set de bras de commande de barre de Bell en aluminium
Set controllo palette stabilizzatore: B450, B400
BLH1628C
Carbon Fiber Paddles: B450, B400
Carbon Paddelstangen: B450, B400
B450, B400 : palettes de barre de Bell en carbone
Palette stabilizzatore in carbonio: B450, B400
BLH1630A
Aluminum Washout Base: B450, B400
Aluminium Pitchkompensator: B450, B400
B450, B400 : partie basse de washout en aluminium
Base cursore o (washout) in alluminio: B450, B400
BLH1631A
Aluminum Washout Control Arm Set: B450, B400
Aluminium Pitchkompensatorhebel Set: B400, B450
B450, B400 : Bras de washout en aluminium
Set braccetti controllo cursore (washout): B450, B400
BLH1633A
Aluminum Swashplate: B450,B400
Aluminium Taumelscheibe: B450, B400
B450,B400 : Plateau cyclique en aluminium
Piatto ciclico in alluminio: B450, B400
BLH1634A
Aluminum Anti-Rotation Bracket/Guide: B450, B400
Aluminium Taumelscheibenführung: B450, B400
B450, B400 : guide de plateau cyclique en aluminium
o in alluminio antirotazione: B450, B400
BLH1654A
Aluminum Tail Drive Shaft Lower Bearing Block: B450, B400
Aluminium Lagersitz Heckrotor: B400, B450
B450, B400 : Palier inférieur d'arbe d'anticouple en aluminium
o cuscinetto per albero trasmissione coda: B450, B400
BLH1655A
Aluminum Speed-Up Tail Drive Gear/ Pulley Assy: B450, B400
Aluminium Riemenabtrieb Heckrotor: B400, B450
B450, B400 : Arbre pignon/poulie transmission d'anticouple aluminium
Adattatore puleggia/ingranaggio trasmissione coda: B450, B400
BLH1657C
Carbon Fiber Tail Boom: B450
Carbon Heckrohr: B450
B450 : Poutre en carbone
Tubo coda in carbonio: B450
BLH1658A
Aluminum Tail Servo Boom Mount: B450
Aluminium Servohalter Heck: B450
B450 : de servo d'anticouple en aluminium
o alluminio per servo coda: B450
BLH1661A
Tail Boom Brace/ Set w/Aluminum Ends: B450
Aluminum Heckrohrabstützung: B450
B450 : Set de renforts et de poutre en aluminium
Set i tubo coda: B450
BLH1662A
Aluminum Horizontal Stabilizer/Fin Mount: B450
Aluminium Stabilisatorhalter: B450
B450 : de dérive et stabilisateur en aluminium
o alluminio per pianetti di coda: B450
BLH1663A
Aluminum Tail Case Set: B450
Aluminium Getriebegehäuse: B450
B450 : Boitier d'anticouple en aluminium
Carter coda in alluminio: B450
BLH1665A
Tail Rotor Shaft and Aluminum Drive Pulley: B450
Aluminium Hechrotorwelle/ Riemenabtrieb: B450
B450 : Axe d'anticouple et poulie aluminuim
Albero rotore coda con puleggia in alluminio: B450
BLH1667A
Aluminum Tail Rotor Pitch Lever Set: B450
Aluminium Heckrotor Pitchhebelset: B450
B450 : Levier de pas d'anticouple en aluminium
Leva comando rotore coda in alluminio: B450
BLH1668A
Aluminum Tail Rotor Pitch Control Slider Set: B450, B400
Aluminium Heckrotor Schiebehülse Set: B450, B400
B450, B400 : Slider d'anticouple en aluminium
Set cursore alluminio controllo o coda: B450, B400
BLH1670A
Aluminum Tail Rotor Grip: B450
Aluminium Heckrotorblatthalter: B450
B450 : Pieds de pales d'anticouple en aluminium
i alluminio per pale rotore coda: B450
BLH1672C
Carbon Fiber Stabilizer/Fin Set: B450
Carbon Leitwerk / Finnen Set: B450
B450 : set de stabilisateur/dérive en carbone
Stabilizzatore e pinna verticale in fibra di carbonio: B450
BLH1676A
Aluminumm Servo Control Arms: B450, B400
Aluminium Servoarm Set: B450, B400
B450, B400 : Bras de servos en Aluminium
Squadrette servo in alluminio: B450, B400
BLH1679A
Aluminum Canopy Mounts: B450
Aluminium Haubenhalter: B450
B450 : s de bulle en aluminium
Set montaggio capottina in alluminio: B450
BLH1681A
Skyfire Canopy: B450
Skyfire Haube: B450
B450 : Bulle Skyfire
Capottina Skyfire: B450
BLH1681B
Inferno Canopy: B450
Inferno Haube: B450
B450 : Bulle Inferno
Capottina Inferno: B450
BLH1681C
Blaze Canopy: B450
Blaze Haube: B450
B450 : Bulle Blaze
Capottina Blaze: B450
BLH1690A
Swash leveling tool: B450, B400
Taumelscheiben Einstellehre: B450, B400
B450, B400 Outil de réglage de plateau cyclique
Attrezzo per livellamento piatto: B450, B400
Intelligent 1-5 Cell LiPo Charger with Balancer
E-flite 1-5 Zellen Lipo Lader mit Balancer
Chargeur-équilibreur Intelligent 1-5 S LiPo
Caricabatterie automatico per 1-5 celle LiPo con bilanciatore
440H Helicopter Motor 4200Kv
440H Helikopter Motor 4200Kv
Moteur brushless hélico 440H 4200Kv
Motore 440H 4200 Kv per elicottero
SPM8800
Spektrum DX8 8CH Transmitter with AR8000/TM1000: No Sxs
SPM8800 Spektrum DX8 8 Kanal Sender mit AR8000/TM 1000 ohne Servos
Emetteur Spektrum DX8 8 voies avec AR8000/ TM1000
Trasmettitore Spektrum DX8 8 canali con AR8000/TM1000: senza servi
BLH1609
Pinion Gear, 9T 0.5M: B450, B400
Ritzel 9 Zähne, 0,5 Modul: B450, B400
B450, B400 : Pignon 9T 0,5m
Pignone 9T 0,5M: B450, B400
BLH1611
Pinion Gear, 10T 0.5M: B450, B400
Ritzel 10 Zähne 0,5 Modul: B450, B400
B450, B400 : Pignon 10T 0,5m
Pignone 10T 0,5M: B450, B400
EFLC4030
3.0-Amp Power Supply, 100-240V AC-12V DC
Netzteil 3.0 Amp 100 - 240V AC -12V DC
Alimentation AC vers 6DC 3.0- Amp 100 - 240V AC -12V DC
Alimentatore 3.0 A, 100-240V AC, 12V DC
EFLC 4030EU
3.0-Amp Power Supply, 100-240V AC-12V DC (EU)
Netzteil 3.0 Amp 100 - 240V AC -12V DC (EU)
Alimentation AC vers 6DC 3.0- Amp 100 - 240V AC -12V DC (EU)
Alimentatore 3.0 A, 100-240V AC, 12V DC (EU)
EFLC 4030UK
3.0-Amp Power Supply, 100-240V AC-12V DC (UK)
Netzteil 3.0 Amp 100 - 240V AC -12V DC (UK)
Alimentation AC vers 6DC 3.0- Amp 100 - 240V AC -12V DC (UK)
Alimentatore 3.0 A, 100-240V AC, 12V DC (UK)
EFLC 4030AU
3.0-Amp Power Supply, 100-240V AC-12V DC (AU)
Netzteil 3.0 Amp 100 - 240V AC -12V DC (AU)
Alimentation AC vers 6DC 3.0- Amp 100 - 240V AC -12V DC (AU)
Alimentatore 3.0 A, 100-240V AC, 12V DC (AU)
EFLC505 EFLM1360H
41
IT
Parts List / Ersatzteile / Pièces de rechange / Pezzi di ricambio #
Part #
English
Deutsch
Françias
Italiano
3 x 6 x 2.5 Bearing Tail Drive Gear-Pulley Assembly (2): B450, B400
3 x 6 x 2.5 Kugellager Heckwelle (2): B450, B400
B450, B400 : Roulement 3x6x2,5 de l'axe pignon/poulie d'anticouple (2)
Ingranaggio-puleggia di trascinamento rotore di coda 3x6x2,5 (2): B450, B400
Dämpferringe 70° (4):450
B450 : Amortisseurs 70 (4)
Umidificatori 70 (4): B450
1
BLH1601
2
BLH1602
Dampeners 70o (4): B450
3
BLH1603
One-Way Bearing Hub w/One-Way Bearing: B450
Gegenstück Freilauf m. Lager: B450
B450 : Moyeu de roue libre/roue libre
Mozzo ingranaggio di autorotazione con ingranaggio di autorotazione: B450
4
BLH1604
Flybar Control Links (2): B450
Anlenkung Paddelstange (2): B450
B450 : Biellettes de barre de Bell (2)
Collegamenti comando flybar (2): B450
5
BLH1605
4 x 8 x 3 Bearing: Main Grip and Tail Shaft (4): B450
4 x 8 x 3 Lager: Main Grip and Tail Shaft (4): B450
B450 : roulements 4x8x3 de pieds de pales (4)
Cuscinetto albero principale e albero di coda 4x8x3 (4): B450
6
BLH1606
Flybar Weights (2): B450, B400
Paddelstange Gewichte (2): B450,B400
B450, B400 : Masselottes de barre de Bell (2)
Pesi flybar (2): B450, B400
7
BLH1607
1.5 x 4 x 2 Bearings: Washout Links (4): B450
1.5 x 4 x 2 Lager: Anlenkung (4): B450
B450 : Roulements épaulés 1,5x4x2 (4)
Cuscinetti 1,5x0,4x2 (4): B450
8
BLH1610
Pinion Gear, 10T 0.5M: B450, B400
Ritzel, 10Z 0.5M: B450, B400
B450, B400 : Pignon 10T 0,5m
Ruota del pignone, 10T 0,5 M: B450, B400
9
BLH1615
325mm Wood Main Rotor Blade Set: B450, B400
Hauptrotorblätter Set Holz: B450, B400
B450, B400 : Pales principales en bois 325mm
Set pale rotore principale in legno da 325 mm: B450, B400
10
BLH1616
Main Rotor Blade Mounting Screw and Nut Set (2): B450
Blatthalterschraube und Mutter Set (2): B450
B450 : Set de vis et écrous pour pales principales (2)
Set viti e dadi di fissaggio pala rotore principale (2): B450
11
BLH1617
Main Rotor Blade Grip/Holder set: B450
Blatthalter : B450
B450 Set de pieds de pales principales
Set pinza porta pale del rotore principale: B450
12
BLH1618
Bell Mixer Arm and Pushrod/Link Set: B450, B400
Bell Mischer Anlenkungs Set: B400, B450
B450, B400 : Set de bras de mixage et tringleries de barre de Bell
Set braccio miscelatore e asta di spinta Bell: B450, B400
13
BLH1619
Bell Mixer Pushrod/Link (2): B450, B400
Bell Mischer Anlenkungs Set ( 2): B400, B450
B450, B400 : tringleries de mixage de barre de Bell
Asta di spinta miscelatore Bell (2): B450, B400
14
BLH1620
Thrust Bearing (2): B450, B400
Lager Blatthalter:B450, B400
B450, B400 : Butées à billes (2)
Cuscinetto reggispinta (2): B450, B400
B450 : axe de pieds de pales (2)
Albero Perno (2): B450
15
BLH1621
Spindle/feathering shaft (2): B450
Schraube / Unterlegscheibe Blattlagerhalter
16
BLH1622
Head Block/Rotor Housing Set: B450
Rotorkopfzentralstück B450
B450 Moyeu de tête rotor
Set blocco di testa/alloggiamento del rotore: B450
17
BLH1623
Flybar Seesaw Holder Set: B450, B400
Paddelstange Zentralstück : B450, B400
B450, B400 : Etrier de barre de Bell
Set fissaggio bilanciere flybar: B450, B400
18
BLH1624
Flybar Paddle Control Frame Set: B450
Paddelstangen Anlenkung Rahmen Set: B450
B450 : palonnier de barre de Bell
Set rinvio del palino: B450
19
BLH1625
Flybar, 220mm (2): B450, B400
Paddelstange, 220mm (2):B450, B400
B450, B400 : Barre de Bell (2)
Flybar, 220 mm (2): B450, B400
20
BLH1628
Flybar Paddles (2): B450, B400
Paddel (2): B450, B400
B450, B400 : Palette de bell (2)
Pale flybar (2): B450, B400
21
BLH1630
Washout Base: B450, B400
Pitchmitnehmer Zentralstück :B400, B450
B450, B400 : Moyeu de washout
Base lavaggio: B450, B400
22
BLH1631
Washout Control Arm and Linkage Set: B450
Pitchmitenehmer Arm u. Verbinderset:B450
B450 : Bras de commande de washout et tringleries
Set braccio di comando lavaggio e collegamento: B450
23
BLH1632
Washout Control Arm Link Set: B450
Pitchlompensator Verbinderstücke: B450
B450 : set de tringleries de washout
Set collegamento braccio di controllo lavaggio: B450
24
BLH1633
Aluminum and Composite Swashplate: B450, B400
Aluminium.Kunststoff Taumelscheibe: B450,B400
B450, B400 : Plateau cyclique alu et composite
Piatto ciclico in alluminio e in composito: B450, B400
25
BLH1634
Anti-Rotation Bracket/Guide: B450, B400
Gegenhalter: B400, B450
B450, B400 : Guide de plateau cyclique
Staffa/guida anti-rotazione B450, B400
26
BLH1635
Control/Linkage Ball, Long (4): B450, B400
Kugelköpfe Lange (10): B400, B450
B450, B400 : Tringleries de commandes longues (4)
Sfera comando/collegamento, lunga (4): B450, B400
27
BLH1636
Control/Linkage Ball, Short (10): B450, B400
Kugelköpfe Kurz (10): B400, B450
B450, B400 : Tringleries de commandes courtes (4)
Sfera comando/collegamento, corta (10): B450, B400
28
BLH1637
Ball Link Set (20): B450, B400
Kugelpfannen (20): B400, B450
B450, B400 : Set de rotules (20)
Set collegamento sfera (20): B450, B400
29
BLH1638
Linkage Rod/Pushrod set: B450, B400
Servogestänge : B450, B400
Linkage Rod/Pushrod set: B450, B400
Set asta di collegamento/asta di spinta: B450, B400
30
BLH1639
Main Frame Set: B450
Ramen Set: B450
B450 : Châssis
Set telaio principale B450 Set leva controllo elevatore: B450, B400
31
BLH1640
Elevator Control Lever Set: B450, B400
Hebelset Nickservo: B450,B400
B450, B400 : Set de leviers de commande de profondeur
32
BLH1641
5 x 8 x 2.5 Bearing: Elevator Control lever (2): B450, B400
5 x 8 x 2.5 Lager :Hebel Nickservo (2): B450, B400
B450, B400 : Roulements 5x8x2,5
Cuscinetto 5x8x2,5: Leva controllo elevatore (2): B450, B400
33
BLH1642
5 x 10 x 4 Bearing: Main Shaft (2): B450, B400
5 x 10 x 4 Kugellager Hauptrotorwelle (2): B450, B400
B450, B400 : Roulements 5x10x4 d'axe principal (2)
Cuscinetto 5x10x4 Albero Principale (2): B450, B400
34
BLH1643
Aluminum Motor Mount Set: B450, B400
Aluminum Motorträger Set: B450, B400
B450, B400 : Set de fixations moteur en aluminium
Set montante del motore in allumino: B450, B400
35
BLH1644
Hook and Loop Battery Strap: B450, B400
Klettband Akkuhalter
B450, B400 : Sangles velcro d'accu
Cinghie di velcro e gancio batteria: B450, B400
36
BLH1645
Landing Gear Set: 450
Kufengestell: 450
B450 : Set de train d'atterrissage
Set del carrello di atterraggio: B450
37
BLH1647
Main Shaft (2): B450
Rotorwelle (2): B450
B450 : Axe principal (2)
Albero Principale (2) B450
#
Part #
English
Deutsch
Françias
Italiano
Freilaufhülse m. Scheibe: B450, B400
B450, B400 : Axe de roue libre et set de rondelles
Albero ingranaggio di autorotazione e spessore: B450, B400
38
BLH1649
One-Way Bearing Shaft and Shim Set: B450, B400
39
BLH1651
Main Gear (2): B450
Hauptzahnrad (2): B450
B450 : Couronne principale (2)
Ingranaggio principale (2): B450
40
BLH1652
One-Way Bearing 6 x 10 x 12: B450, B400
Freilauf 6 x 10 x 12: B450, B400
B450, B400 Roue libre 6x10x12
Ingranaggio di autorotazione 6x10x12: B450, B400
41
BLH1653
Main Tail Drive Gear (2): B450
Zahnrad Heckrotorantrieb (2).B450
B450 : Couronne d'anticouple (2)
Ingranaggio principale di trascinamento della coda (2): B450
42
BLH1654
Tail Drive Shaft Lower Bearing Block/ Mount: B450
Halter Heckrotorwellenlager: B450
B450 : de roulement inférieur
Blocco/montante cuscinetto inferiore albero di trascinamento di coda: B450
43
BLH1655
Tail Drive Gear/Pulley Assembly: B450
Zahnrad Heckrotorriemen: B450
B450 : Arbre d'anticouple pignon/ poulie
Gruppo ingranaggio/puleggia di trascinamento di coda: B450
44
BLH1656
Tail Drive Belt: B450, B400
Heckrotor Riemen: B450, B400
B450, B400 : Courroie d'anticouple
Cinghia di trascinamento di coda: B450, B400
45
BLH1657
Tail Booms (2): B450
Heckrohr (2): B450
B450 : Poutre de queue (2)
Aste di coda(2): B450
46
BLH1658
Tail Servo Boom Mount (2): B450
Servobefestigung Heckrohr (2): B450
B450 : Fixations de servo d'anticouple
Montante asta servo di coda (2): B450
47
BLH1659
Tail Linkage/Pushrod set (2): B450
Anlenkstange Heckrotor: (2)
B450 : Tringlerie de commande d'anticouple (2)
Set collegamento di coda/asta di spinta (2): B450
48
BLH1660
Tail Pushrod /Guide Set: B450
Halter Heckrotoranlenkstange: B450
B450 : Set de guide de commande d'anticouple
Set o/guida asta di spinta della coda: B450
49
BLH1661
Tail Boom Brace/ Set (2): B450
Heckrotor Abstützung und Halter Set (2): B450
B450 : Set de reforts et s de tube de queue (2)
Braccio asta di coda/set di sostegno(2): B450
50
BLH1662
Horizontal Stabilizer/Fin Mount: B450
Leiterksbefestigung/ Heckfinne: B450
B450 : Fixation de dérive et stabilisateur
Montante deriva/stabilizzatore orizzontale: B450
51
BLH1663
Tail Case Set: B450
Heckrotor Gehäuse: B450
B450 : Boitier d'anticouple
Set alloggiamento coda: B450
52
BLH1665
Tail Rotor Shaft and Drive Pulley (2): B450
Heckrotorschaft (2): B450
B450 : Axe et poulie de rotor d'anticouple (2)
Albero rotore di coda e puleggia di trascinamento (2): B450
53
BLH1666
2 x 5 x 2.5 Bearing: Paddle Control Frame: B450, B400
2 x 5 x 2.5 Kugellager Paddelstange: B450, B400
B450, B400 Roulement 2x5x2.5 de bras de washout(2)
2x5x2,5 cuscinetto braccio miscelazione lavaggio (2): B450, B400
54
BLH1667
Tail Rotor Pitch Lever Set: B450
Heckrotor Anlenkungset: B450
B450 : Set de levier de pas d'anticouple
Set leva o del rotore di coda: B450
55
BLH1668
Tail Rotor Pitch Control Slider Set: B450
Heckrotor Schiebhülse Set: B450
B450 : Set de slider d'anticouple
Set cursore comando o rotore di coda: B450
56
BLH1669
Aluminum Tail Rotor Hub Set: B450
Heckrotorzentralstück Aluminium Set: B450
B450 : Moyeu d'anti couple en alu
Set mozzo del rotore di coda in alluminio: B450
57
BLH1670
Tail Rotor Blade Grip/Holder Set: B450
Blatthalter Heckrotor: B450
B450 : Pieds de pales d'anticouple
Set pinza/sostegno pale del rotore: B450
58
BLH1671
Tail Rotor Blade Set: B450
Rotorblätter Heckrotor: B450
B450 : Set de pales d'anticouple
Set pale del rotore di coda: B450
59
BLH1672
Stabilizer/Fin Set, White: B450
Leitwerk / Heckfinne, weiss: B450
B450 : Set Dérive/stabilisateur
Stabilizzatore/deriva, bianco: B450
60
BLH1673
Complete Hardware Set: B450
Schraubensatz kpl. : B450
B450 : Set de visserie
Set completo hardware: B450
61
BLH1674
Mounting Accessories, Screwdriver, & Wrench: B450, B400
Montage Werkzeug: Schraubendreher und Schlüssel
B450, B400 : Set d'outils tournevis et clés
Mnting Access. Cacciavite e chiave: B450, B400
62
BLH1676
Servo Arm Set: B450, B400
Servo Arm Set: B450,B400
B450, B400 : Bras de servos
Set braccio del servo: B450, B400
63
BLH1679
Canopy mounts (2): B450
Halter Kabinenhaube (2): B450
B450 : Fixations de bulle (2)
Staffe di montaggio calottina (2): B450
64
BLH1681
Canopy: B450
Kabinenhaube: B450
B450 Bulle Cold fusion (origine)
Calottina Cold Fusion (a magazzino): B450
G210HL Micro Heading Lock MEMS Gyro
G210 MEMS Micro Heading Lock Kreisel
Micro Gyro G210HL à conservateur de cap MEMS
G210HL Giroscopio MEMS Micro Blocco Coda
RTF
65
EFLRG210HL
66
EFLRDS76
7.6-Gram Sub-Micro Digital Servo
7.6-Gram Sub-Micro Digital Servo
Sub Micro Servo digital 7.6g
Servo digitale sub-micro da 7,6 grammi
67
EFLRDS76T
7.6-Gram Sub-Micro Digital Tail Servo
7.6-Gram Sub-Micro Digital Heck Servo
Sub Micro Servo digital d'anticouple 7.6g
Servo digitale sub-micro di coda da 7,6 grammi
68
SPMAR 6115E
AR6115E Micro Lite 6-Channel Receiver, End Pin
AR6115E Microlite 6 Kanal Empfänger
Récepteur Spektrum 6 voies AR6115E Microlite
Ricevitore Spektrum AR6115E Microlite a 6 canali
69
EFLA335H
35-Amp Helicopter Brushless ESC
35-Amp Hubschrauber Brushless Regler: B450
B450 Contrôleur Brushless Hélico 35A
ESC Elicottero Brushless 35 Amp: B450
70
EFLB 22003S30
2200mAh 3S 11.1V 30C LiPo, 13AWG EC3
2200mAh 3S 11.1V 30C LiPo Akku, 13AWG EC3
Li-Po 30 C 2 200 mAh 11,1 V 3S
3S 11,1 V 220 mAh 30C Li-Po
71
BLH1001
Mini Helicopter Main Blade Holder: B450, B400
Blatthalter Mini Hubschrauber: B450, B400
B450, B400 : de pales principales Hélico
B450, B400 : o pala rotore principale di elicottero
©2010 Horizon Hobby, Inc.
72
EFLC3115
3S 11.1V LiPo Balancing Charger, 1.8A
3S 11.1V LiPo Balancer Ladegerät, 1.8A
Chargeur-équilibreur Li-Po CC
Caricabatterie con bilanciatore CC Li-Po
US patent number 7, 391, 320. Other patents pending.
73
SPMR6600
DX6i Transmitter Only
DX6i nur Sender
Émetteur DX6i seul
Solo trasmittente DX6i
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
74
EFLM1350H
420H Helicopter Motor 3800Kv: B400, B450
420H Hubschrauber Motor 3800Kv: B400, B450
Cage-tournante brushless 420 H, 3 800 Kv
420H Brushless outrunner, 3800 Kv
Blade, DSM2, EC3 and Bind-N-Fly are trademarks or ed trademarks of Horizon Hobby, Inc. Futaba is a ed trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan Created 12/10 27560 BLH1600 / BLH1650
Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the tab for this product.
Meaning of Special Language The following are used throughout the product literature to indicate various levels of potential harm when operating this product: 9
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
10 15
15
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
14 11
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
16
11 5
11
16
5
20
12
12 16
12
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
6
2
28
53 12
12
15
18 29
16
51
12
5 12
16 11
2 16
28
22
29 11
17
59
53
11
18
28
21
22
11
19
4
14
23
21
51 51
10
5
15
58
18
50
54
58
18
52
57
5
6
59
54
18
55
20
5
18 6
56 56
56
18
51
5
28
20 37
57 57
57
47
29
5
45
57
28
58
28
48
28
48
50 58
48
50
25
63
48
44
1
29
43
• Always store the battery at room temperature in a dry area for best results. • Always transport or temporarily store the battery in a temperature range of 40–120º F. Do not store battery or model in a car or direct sunlight. If stored in a hot car, the battery can be damaged or even catch fire. • NEVER USE A Ni-Cd OR Ni-MH CHARGER. Failure to charge the battery with a compatible charger may cause fire resulting in personal injury and/or property damage. • Never discharge Li-Po cells to below 3V under load. • Never cover warning labels with hook and loop strips.
CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-Po batteries can result in a fire, personal injury, and/ or property damage. • By handling, charging or using the included Li-Po battery you assume all risks associated with lithium batteries. • If at any time the battery begins to balloon or swell, discontinue use immediately. If charging or discharging, discontinue and disconnect. Continuing to use, charge or discharge a battery that is ballooning or swelling can result in fire.
62
31
33 32
66
28
3 1
30 40 38
76
42
39
66
28
The Battery Charger included with your aircraft is designed to safely charge the Li-Po battery.
27
33
67
32
Never charge damaged Batteries.
74
29
34
28
64
38
41
62 63
34
42
8 34
64
38
34
68
38
64
30 69
33
36
36
2
28 28
31
65
Store Batteries safely.
30
34
62
49 49
29
46
28 46
29
63 46 46
Never charge Batteries outside recommended levels.
62
66
5 56
Battery Warnings
9
24
4
18
54
57
57
EN
15
21 23
Age Recommendation: Not for children under 14 years. This is not a toy. • Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control. • Always operate your model in open spaces away from full-size vehicles, traffic and people. • Always carefully follow the directions and warnings for this and any optional equipment (chargers, rechargeable battery packs, etc.). • Always keep all chemicals, small parts and anything electrical out of the reach of children. • Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics. • Never place any portion of the model in your mouth as it could cause serious injury or even death. • Never operate your model with low transmitter batteries.
Never charge Always charge Batteries away from Batteries outside safe temperature range. flammable materials.
12
18 5
Additional Safety Precautions and Warnings
Never leave charging Batteries unattended.
28
10