Carprog Mcu Reflash Step By Stepg 5a606

Carprog Mcu Reflash Step by step

1 z 12

http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...

Edited by Foxit Reader Copyright(C) by Foxit Software Company,2005-2007 For Evaluation Only. Realtime Posts

What's New?

Forum

New Posts:

Satellite Forums

Private Messages

FAQ

Garage Forum

Calendar

Community

Cable Forum

Apple Forum

Forum Actions

Quick Links

s

Chatbox

Videos

Android Forum

Type Here... Advanced Search

Welcome, briangsm Forum

The Garage

Notifications: 14

Airbag, ChipTuning, Dash, ECU, IMMO, Locksmith, Radio, SatNav

My Profile

Settings

Log Out

Guides, Procedures & Tutorials

Carprog Mcu Reflash Step by step Results 1 to 15 of 176

+ Reply to Thread Carprog Mcu Reflash Step by step Here is how to reflash CARPROG Mcu AT91SAM7S256 step by step, first ...

View First Unread

Last

Page 1 of 12 1 2 3 4 5 6 11 ...

3 Likes LinkBack

Thread Tools

Search Thread

Rate This Thread

Display #1

26th August, 2012, 09:18 PM

audiotek


Date:

May 2011

Location:

Mexico

Posts:

149

Here is how to reflash CARPROG Mcu AT91SAM7S256 step by step, first of all I wish to thanks to lupu_sandu, elchip, autocargo, Tachonow, carradio2001 and all DK forum who made this possible. I bought my Carprog clone 4.01 from digi_obd but after about 50 uses starts a counter: "260 uses left update hardware to synchronize" and was decreasing, anyway 260 uses is big number to recover the investment (us $209 dlls), the programmer was paid before the counter starts.

Thanks:

0

Ok, first we need this stuff:

Top Poster

Thanked 1 Time in 1 Post 3

s: s:

0

1.- AT91SAM7S256 bin: http://www.digital-kaos.co.uk/forums...og-rev-0.3.rar 2.- Jtag programmer:

3.- Jtag software: http://www.digital-kaos.co.uk/forums....1-release.rar We need to prepare the Carprog to connect to Jtag programmer but first the flash need to be erased, the Jtag function in mcu is dissabled, you can't connect to the mcu before erase the flash. Remove the AT88SC eeprom from the board, please note where is the pin 1 in eeprom before remove:

Carefully lift the pin 55 (reset) of the mcu and solder a wire and secure it with a small ammount of silicone (you don't want to broke the pin in the process). Connect the Carprog (with the pin 55 dissconected) to the 12v supply, wait about 10 seconds and connect the wire from pin 55 to Vcc (3.3V) in Carprog:

2013-04-08 19:46


2 z 12


Wait from 5 to 10 seconds after connect the 12v supply, the flash content will be erased and the Jtag option of the Mcu will be enabled now. If not work leave connected for about 3 to 5 minutes. Disconnect the 12v supply from carprog and remove the pin 55 wire from vcc. The pin 55 must remain disconnected until the programming process is done. Install the H-JTAG software in your pc.

Last edited by audiotek; 27th August, 2012 at 04:48 PM.

Xprog-m clone, Tachopro 2008.01, Willem PCB50 Upa-usb clone, Martech Clip, Masterprog Nec prog, Orion programmer , Carprog clone Licznik usb, Vag k + Commander 1.4 & 3.6 Autocom CDP+ 3 in 1, ElmScan 5, Obd Scan 1.5 Ponyprog Interfaces, Micronas OBD Tool OTC 9450, VCS Scanner interface, VAS 5054A Vagcom 10.6, 11.2 and 11.11, DIS 5.7 and Progman BOSCH J2534 ES6510, XHORSE M-VCI Toyota, Tachopro 2.0, Easy J2534 Universal Programmer, Thanks

Reply

Reply With Quote

The Following Says Thank You to audiotek For This Useful Post: ligno1 (Yesterday) #2

26th August, 2012, 09:39 PM

audiotek Top Poster

Now we can make the connections from Carprog to Jtag programmer:

2013-04-08 19:46


3 z 12

Date:

May 2011

Location:

Mexico

Posts:

149

Thanks:

0


Carprog Pinout:


s: s:

0

Jtag Pinout:

And here is the Carprog connected to the JTAG programmer (note that the pin 55 wire is disconnected):


Reply

Reply With Quote

#3

26th August, 2012, 09:56 PM

audiotek Top Poster

After the H-Jtag sotware is installed we can procced to configure: Open the H-Jtag server and make the adjustments:

2013-04-08 19:46


4 z 12

Date: May 2011 Location:

Mexico

Posts:

149

Thanks:

0


Select the port:


s: s:

0

LPT Jtag setting:

TAP configuration:

Target manager:

Now connect the carprog to JTag programmer and 12v supply and press "Detect Target" in H-TAG server, now the Carprog Mcu is detected!!!:

2013-04-08 19:46


5 z 12


Last edited by audiotek; 26th August, 2012 at 10:59 PM.


Reply

Reply With Quote

#4

26th August, 2012, 10:35 PM

audiotek Top Poster Date:

May 2011

Location:

Mexico

Posts:

149

Thanks:

0

Now we procced to program the AT91 mcu: Start the H-FLASHER and select the AT91SAM7S256 from the list:


s: s:

0

-Go to "4 Programming" in the programming wizzard and press "Check" to the communication with the target mcu, if all is ok the values must be: Flash: AT91SAM7S256 0x270D0940 Target: ARM7TDMI LITTLE-ENDIAN -In "Type" select: "Plain Binary Format" -In "Dst Addr" select: "Flash Base Address" -In "Src File" select the location of the AT91SAM7S256 bin in your hard drive.:

Now press the "Program" button and wait to finish:

2013-04-08 19:46


6 z 12


If the progrmming was succefull you will receive the next message:

You can again if everything is ok by pressing the button "":

The programming process is finished!!, disconnect the 12v supply, then disconnect the programmer from carprog, solder the pin 55 wire to Ground (check the picture) and put back the AT88SC eeprom, reassemble the carprog and test it.

I already made some further tests and the Carprog works well with any version of the software and the COUNTER IS GONE!!! Tested with versions: 3.75, 4.0, 4.1, 4.5, 4.85 and 4.86, the counter never start again.

Last edited by audiotek; 27th August, 2012 at 12:54 AM.

Xprog-m clone, Tachopro 2008.01, Willem PCB50 Upa-usb clone, Martech Clip, Masterprog Nec prog, Orion programmer , Carprog clone Licznik usb, Vag k + Commander 1.4 & 3.6

2013-04-08 19:46


7 z 12


Autocom CDP+ 3 in 1, ElmScan 5, Obd Scan 1.5 Ponyprog Interfaces, Micronas OBD Tool OTC 9450, VCS Scanner interface, VAS 5054A Vagcom 10.6, 11.2 and 11.11, DIS 5.7 and Progman BOSCH J2534 ES6510, XHORSE M-VCI Toyota, Tachopro 2.0, Easy J2534 Universal Programmer, Thanks

Reply

Reply With Quote

#5

4th September, 2012, 04:17 PM


May 2011

Location:

Mexico

Posts:

149

Thanks:

0

Carprog modification for fast reflash I made a modification to my Carprog clone for fast reprogramming, if I need to do it again will not be necessary to open it again and redo all connection every time I want or need to reprogram:


s: s:

0

I used the Carprog pins from 15 to 21, those pins are useless for the programmer or any adapter, they are disconnected:

I used a "selector" like the desktop's pc for bios, to select the programming mode, in picture from left to right: 1, 2 3, if the jumper is placed at pins 1 and 2, the pin 55 (reset) from the AT91 is shorted to ground, preventing deprogramming or programming the MCU, if the jumper is placed at pins 2 and 3 the pin 55 is shorted to vcc 3.3v and the Mcu is placed in ERASE MODE. Without jumper the mcu is placed in programming mode:

2013-04-08 19:46


8 z 12


Now is probably a waste of time, in the near future will save me some time but from now I can reflash the AT91 in less than 5 minutes. Update: I forgot to mention that I doesn't need to remove the AT88SC eeprom to ERASE/REFLASH the AT91 mcu. After that the Carprog works well. This is MY OWN experience, so, If you want to do the same, do it at YOUR OWN risk.

Last edited by audiotek; 4th September, 2012 at 07:40 PM. Reason: title


Reply

Reply With Quote

#6


olegario DK Veteran Date:

Apr 2010

Location:

LT & ES

Posts:

373

Thanks:

0

And how you plan to remove fast AT88SC eeprom, to protect it's content?


s: s:

0

Thanks

Reply

Reply With Quote

#7


ahadi DK Veteran

I have question about the ground why this connection .

Attached Thumbnails

Date:

Sep 2009

Location:

JerusalemPalestine

Posts:

384

Thanks:

1

Thanked 0 Times in 0 Posts 9

s: s:

0

Thanks

Reply

Reply With Quote

#8


carradio2001 DK Veteran

Originally Posted by audiotek

2013-04-08 19:46


9 z 12


I made a modification to my Carprog clone for fast reprogramming, if I need to do it again will not be necessary to open it again and redo all connection every time I want or need to reprogram

Not necessary IF use the correct dump ! Carradio2001. Date:

Nov 2009

Location:

Posts:

335

Thanks:

2


s: s:

0

Thanks

Reply

Reply With Quote

#9



May 2011

Location:

Mexico

Posts:

149

Thanks:

0


s: s:

Originally Posted by olegario

And how you plan to remove fast AT88SC eeprom, to protect it's content?

Here is your answer: I have two Carprog clone units, so, I take the risk and make all the reflash procedure without removing the AT88SC eeprom and the results are the same: the carprog unit works well after reflashing, the contents in AT88SC eeproms remains intact. I already make some tests with airbag modules, eerpom reading, some dashboards and mcu's and everything is ok.

0


Reply

Reply With Quote

#10



May 2011

Location:

Mexico

Posts:

149

Thanks:

0


s: s:

Originally Posted by carradio2001

Not necessary IF use the correct dump ! Carradio2001.

As I said at the end of the post: "Now is probably a waste of time, in the near future will save me some time but from now I can reflash the AT91 in less than 5 minutes." I doesn't share this with the intention that other people do the same, it's your/they choice and risk anyway, it's only to comment that it's possible reflash the carprog MCU without removing the AT88SC eeprom (at my own experience). BR...

0

Xprog-m clone, Tachopro 2008.01, Willem PCB50 Upa-usb clone, Martech Clip, Masterprog Nec prog, Orion programmer , Carprog clone Licznik usb, Vag k + Commander 1.4 & 3.6 Autocom CDP+ 3 in 1, ElmScan 5, Obd Scan 1.5 Ponyprog Interfaces, Micronas OBD Tool OTC 9450, VCS Scanner interface, VAS 5054A Vagcom 10.6, 11.2 and 11.11, DIS 5.7 and Progman BOSCH J2534 ES6510, XHORSE M-VCI Toyota, Tachopro 2.0, Easy J2534 Universal Programmer,

2013-04-08 19:46


10 z 12


Thanks

Reply

Reply With Quote

#11


carradio2001 DK Veteran

That's good to know, re-flash possible without removing AT88SC eeprom. Carradio2001.

Date:

Nov 2009

Location:

Posts:

335

Thanks:

2


s: 0

s:

Thanks

Reply

Reply With Quote

#12


coops43 Newbie Date:

Feb 2010

Posts:

3

Thanks:

0

Carprog Software Does this mean that the carprog software will have all the functions of software version 4.86? If so does anyone know where I can get the software from please?


s: 0

s:

Thanks

Reply

Reply With Quote

#13


radsky Top Poster

Originally Posted by coops43

Does this mean that the carprog software will have all the functions of software version 4.86?

no If so does anyone know where I can get the software from please? Date:

May 2012

Location:

Earth

Posts:

182

Thanks:

0

use magic "search" button.


s: s:

0

Thanks

Reply

Reply With Quote

#14


coops43 Newbie Date:

Feb 2010

Originally Posted by radsky

no

2013-04-08 19:46


11 z 12

Posts:

3

Thanks:

0


use magic "search" button.


s: s:

I can't find it!!!!

0

Thanks

Reply

Reply With Quote

#15


guilhermegti Junior Member Date:

Jul 2011

Posts:

27

Thanks:

3

Is this jtag ok for the job? It's an old one i have here from sat boxes. thanks

Attached Thumbnails Thanked 5 Times in 2 Posts 30

s: s:

0

Last edited by guilhermegti; 7th September, 2012 at 11:14 PM.

Thanks

Reply

Reply With Quote

Page 1 of 12 1 2 3 4 5 6 11 ...

+ Reply to Thread

Last

Quick Reply

« Previous Thread | Next Thread » Thread Information

There are currently 1 s browsing this thread. (1 and 0 guests) briangsm Tags for this Thread

None View Tag Cloud

Add / Edit Tags

Posting Permissions

You may You may You may You may

post new threads post replies post attachments edit your posts

BB code is On Smilies are On [IMG] code is On [VIDEO] code is On HTML code is Off Trackbacks are On

Pingbacks are On Refbacks are On Forum Rules

2013-04-08 19:46


12 z 12

Us

Digital Kaos


Sitemap

Top

-- DarkCore - Blue

All times are GMT. The time now is 05:26 PM. Powered by vBulletin® Version 4.2.0 Copyright ©2000 - 2013, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.1 Digital Kaos does not condone any illegal operations, including obtaining tv for free. Digital Kaos does not accept responsibilty for the loss of any equipment used. Everything discussed on this forum is for experimental and educational purposes only. Use the information at your own risk.

2013-04-08 19:46

Carprog Mcu Reflash Step By Stepg 5a606

Overview 26281t

More details 6y5l6z

Related Documents 3h463d

Carprog Mcu Reflash Step By Stepg 5a606

Mcu 3k3y4

Step By Step 2d2644

Woodwork Step By Step 681u2t

Step By Step 2d2644

Korean Step By Step 6b632z

More Documents from "Aleksandar" 3w25z

Carprog Mcu Reflash Step By Stepg 5a606

Mathcad-mechanical Engineers Making Better Decisions Faster k14g

Llt Guide 1eax

Roberto-savijano-gomora-pdf.pdf 273l1n

Milioner Kviz 4l2u44

Cdet Guide V2 3 3c4s61