Error Code Copier Canon 1r104h

ERROR CODE COPIER CANON E000 F problem, F heater, F film, Thermistor, Connections, Power Supply E001 F Temperature too high, F heater, F film, Thermistor, Connections, Power Supply E002E003 Low F Temperature, Thermistor, F heater, F film, Connections, Power Supply E004 F problem, triac shorted, thermistor, power supply E007 F film rotation problem ( IR 2200, 2800, 3300 or i ) E009 F does not match power supply or DC controller board E010 Drive problem, main motor, motor drive board, mechanical gear functions E014-0000 F motor ( IR 2200, 2800, 3300 or i ) E019-0000 Waste toner full ( IR 2200, 2800, 3300 or i ) E032-0001 DA unit communications error ( IR 2200, 2800, 3300 or i ) E040 Holding plate drive assembly, holding plate position sensor or holding plate solenoid E043 Paper deck feed motor problem E051-0000 Horizontal registration home detect mechanism ( Motor M9 or sensor PS10 ) ( IR 2200, 2800, 3300 or i ) E054 Duplex feed roller home position sensor lever, duplex feed roller gear, duplex drive board, duplex feed clutch, or duplex motor E055 Horizontal registration guide, home sensor lever, drive gear, duplex drive board, horizontal registration motor or duplex drive motor E064-0000 Charge, transfer or developer bias problem E100 Laser unit, BD mirror, image processor board, laser board, DC controller, can also

happen if drum is not installed E102 Laser problem E110-0000 Laser motor ( IR 2200, 2800, 3300 or i ) E202-0001 Scan problem, scan switch, scan motor, image processor board ( IR 2200, 2800, 3300 or i ), locked with error message E203 Scan motor driver board, scan motor or reader controller board E204-0001 ADF lead edge image signal problem ( IR 2200, 2800, 3300 or i ) E211/215 Reader controller board, exposure lamp heater, exposure lamp thermistor, flat cable connections E216 Exposure lamp, inverter board, reader controller board E217 Exposure lamp heater or heater controller board E219 Exposure lamp, inverter board, reader controller board E220-00001 Exposure lamp inverter board ( IR 2200, 2800, 3300 or i ) E225-0000,-00002 White plate/edge whit plate read error, bad CCD or exposure lamp ( IR 2200, 2800, 3300 or i ) E240-0000 Mcon-Dcon problem, bad DC controller ( IR 2200, 2800, 3300 or i ) E243-0000 Control to image processor board communication problem, main controller board ( IR 2200, 2800, 3300 or i ) E248-0001 EEPROM problem ( IR 2200, 2800, 3300 or i ) E261-0000 Zero cross signal problem, main control board or DC controller board E302-0001, -0002 Shading error, CCD, reader board or main controller board ( IR 2200, 2800, 3300 or i ) E315 Image data problem, main controller board ( IR 2200, 2800, 3300 or i )

E400 RDF to copier communication problem E401 RDF pickup motor or pickup sensor E402 RDF belt motor or pulse sensor E403 RDF feed motor or pulse sensor E404 DRF delivery motor problem E420-0001 ADF back up data ( IR 2200, 2800, 3300 or i ) E421-0001 ADF back up data ( IR 2200, 2800, 3300 or i ), communication problem E422-0001ADF IPC error E500 Finisher main board or communication with copier E501-0001 Saddle finisher communications with punch E503-03 Finisher saddle-stitcher communication problem E504-01,-02,-03,-04 Finisher height sensor problem E505-0001,-0002 Finisher back up RAM error E510-0001,-0002 Finisher feed motor ( IR 2200, 2800, 3300 or i ) E512-01,-02 Finisher delivery motor or delivery motor clock sensor E513-01,-02 Finisher alignment motor or alignment motor home sensor E514 Stack delivery motor, sensor E530 Rear jogging plate motor, sensor E531 Finisher stapler motor, home sensor E532-01,-02

Finisher stapler motor or its home sensor E535-01,-02 Finisher delivery motor or its swing guide switches E535-03 Finisher safety switch or swing guide switch E537Front jogging plate motor M3, front aligning plate home sensor E540-0000,-00002,-0003 Finisher tray up/down motor ( IR 2200, 2800, 3300 or i ) E551 Finisher fan E577 Finisher delivery motor or sensor E580 Finisher stack tray upper limit sensor or up/down motor problem E583 Finisher tray aux plate motor or sensor E584-01,-02,-03 Finisher feed motor, feed motor switch or shutter closed switch E585-0000 Finisher stack handling E590-0000,-0002 Punch motor E592-0000,-0002,-0003,-0004,-0005 Horizontal registration sensor, 0006 is punch sensor error E593-0001,-0003 Punch shift motor E5F1-0001,-0002,-0003 Finisher saddle folder motor E601-0000,-0001 Image transfer error, hard drive, main controller, DC controller E602-0001,-0002 Hard disk error, reinstalled software, hard drive or DC controller bad E604-0000 Image memory, hard drive or main controller board E605-0001 Image memory battery, hard drive or main controller board E606-0001 HDD mounting fault, reinstalled software, replace HDD or main controller board,

connections E674-0000 Fax unit problem E676 PDL board connection, PDL board, systems controller board E677-0001 PDL board, printer board or main controller board E710-0001,-0002,-0003 IPC initialization problem E711-0001,-0002,-0003 IPC E712-0001,-0002 Communication problem with document feeder E713-0000 Communication problem with finisher E716-0000 Communication problem with pedestal E717-0001 Communication problem with ASSIST E719-0001 Card reader, coin vendor communication problem E731 Relay board, PDA board, network board, image processor board, system controller board E732-0001 Reader communication problem E733-0001 Printer communication problem E734 Relay board, PDA board, network board, image processor board, system controller board E735 Relay board, PDA board, network board, image processor board, system controller board E736 Fax board or system controller board E737-0000 SDRAM problem, DIMM or system controller E738

Network board, relay board, system controller board E739 Network board, relay board, system controller board E740-0001,-0002,-0003 Ethernet board E741-0000 PCI bus error E742 RIPI board E743-0000 Mcon-Rcon communication error E744-0000 Boot ROM software problem E803-0000 Low voltage power supply problem E804 Printer unit power supply fan, DC controller E805 Laser motor, DC controller, ( Developer Fan or other Fan on IR series ), Bad fan, DC controller or image processor board E807 F /scanner fan or DC controller E810 (IR models) No drum in machine E826 By fan or DC controller board E827 Controller power supply fan problem E901-0000 Pedestal feed unit motor or board E903 Paper deck lift problem