harman/kardon
SB 15/230 Service Manual
harman/kardon
Service Manual
SB 15/230 Soundbar with wireless subwoofer
CONTENTS ESD WARNING INTRO AND CONTENTS CONTROLS AND CONNECTIONS SUBWOOFER CONNECTIONS PROGRAMMING THE SOUNDBAR TROUBLESHOOTING SPECIFICATIONS NEW ON/OFF EXPLANATION
Released EU2010
2 3 4 5 6 7 8 9
PACKAGE GUIDE AND PARTS, CENTER 10 PACKAGE GUIDE AND PARTS, SUB 11 EXPLODED VIEW AND PARTS, CENTER 12 EXPLODED VIEW AND PARTS, SUB 13 ELECTRICAL PARTS LIST 14 SCHEMATIC DIAGRAMS 16 PCB DRAWINGS 20-30
Harman Consumer Group, Inc. 8500 Balboa Boulevard Northridge, California 91329
Rev 0, 05/2010 Page 1 of 30
harman/kardon
SB 15/230 Service Manual
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
Each precaution in this manual should be followed during servicing. Components identified with the IEC symbol
in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer.
Page 2 of 30
SB 15/230 Service Manual
Harman Kardon® SB 15/230
Included
Introduction
One SB 15CNTR soundbar speaker
ENGLISH
harman/kardon
Thank you for purchasing the Harman Kardon® SB 15/230 speaker system, with which you’re about to begin many years of listening enjoyment. The SB 15/230 has been custom-designed to provide the excitement and power of the cinema experience in your own living room. While sophisticated electronics and state-of-the-art speaker components are hard at work within the SB 15/230, hookup and operation are simple. To obtain maximum enjoyment from your new soundbar speaker system, we urge you to take a few minutes to read through this manual. This will help ensure that the connections you make are correct. In addition, a few minutes spent learning the functions of the various controls will enable you to take advantage of all the power and refinement the SB 15/230 is able to deliver.
One SB 15SUB 10-inch (250mm) 100-watt wireless subwoofer
If you have any questions about this product, its installation or its operation, please your dealer, the best local source of information.
Description and Features The SB 15/230 is a complete home theater speaker system that includes: •• A video-shielded stereo soundbar speaker (the SB 15CNTR) with two-way dualdriver left and right speakers and built-in 25-watt x 2 stereo amplifier •• A 10-inch (250mm), 100-watt wireless powered subwoofer (the SB15SUB) •• Wall-mount brackets for the soundbar
Two wall-mount brackets for the SB 15CNTR soundbar
•• A 6.5-foot (2m) stereo audio cable for connecting the system directly to your TV’s audio output. The SB 15CNTR soundbar contains the system’s left and right speakers and stereo amplifiers, and features digital signal processing with virtual 3D surround circuitry that creates a complete surround-sound experience without any extra speakers or wires. You can set the soundbar on a table in front of your TV, and the system includes hardware that makes it easy to mount the soundbar on the wall along with your flat- TV. You can program the soundbar to respond to your TV remote’s volume, power and source commands.
One 24V DC power supply and AC power cord for the SB 15CNTR speaker
The SB15SUB subwoofer receives its signal from the SB 15CTR soundbar via wireless technology, so you can place it anywhere in your room without having to run any wires. Its 10-inch (250mm) woofer and built-in 100-watt amplifier deliver a movie’s impact and excitement. Other conveniences include a volume control, a phase switch for fine-tuning bass response to suit your listening environment, and an efficient switching system that senses the presence of an audio signal and automatically switches the subwoofer on. Harman Kardon invented the high-fidelity receiver more than 50 years ago. With state-of-the-art features and time-honored circuit designs, the SB 15/230 will turn your flat-screen TV into a fun and exciting home theater.
One 6.5-foot (2m) stereo audio cable
Important If anything is missing, or if any part of your SB 15/230 system fails to operate properly, your dealer immediately.
3 Page 3 of 30
harman/kardon
SB 15/230 Service Manual
Soundbar Top- Controls
Power Button
Power Indicator
Surround Mode Button
Surround Mode Indicator
Volume Up/Down Buttons
Soundbar Rear- Controls and Connections Wireless Code Switch: Selects between four different channels for the wireless subwoofer signal.
Source Selector Button
IMPORTANT: Be sure to set the subwoofer’s Wireless Code switch to the same channel that you set the soundbar’s Wireless Code switch. See Wireless Code Switches, on page 9, for more information. EQ Switch: This switch adjusts the soundbar’s bass for either wall or table mounting. If you’re mounting the soundbar on a wall with the included wall-mount brackets, set this switch to the Wall position for the most natural-sounding bass performance. If you are placing the soundbar on a table, set the EQ switch to the Table position for the most natural-sounding bass performance.
Source Indicator
Power Button: When the soundbar is in the Standby mode (the Power Indicator is amber), press this button to turn the SB 15/230 system On. (The Power Indicator turns blue.) NOTE: When the soundbar is in the Standby mode, it will automatically turn On whenever it detects an audio signal at the Source 1 (analog) inputs.
Trim Switch: This switch adjusts the soundbar’s input sensitivity so it will work with TVs that have different audio signal output levels. See Soundbar Trim Switch, on page 9, for more information.
When the SB 15/230 system is On:
Source 1 Connection (analog): Use the included stereo audio cable to connect the stereo analog outputs of your TV, DVD player or cable/satellite tuner here.
•• Momentarily press the Power button to mute the SB 15/230 system. (The Power Indicator flashes blue.)
Source 2 Connection (digital): If your TV, DVD player or cable/satellite tuner has a coaxial digital output, you can connect it here.
•• Hold down the Power button for three seconds to put the soundbar in the Standby mode. (The Power Indicator turns amber.) NOTE: The subwoofer will remain on for approximately 15 minutes after the audio signal ceases, then will automatically go into the Standby mode.
NOTE: If you connect your TV or another component to the soundbar’s Source 1 connection, you can connect a different component to the Source 2 connection. Power Connection: Connect the included DC power supply here. See Power Connections, on page 7, for more information.
Surround Mode Button: This button turns the SB 15/230 system’s 3D Surround processing On and Off. The Surround Mode Indicator turns blue when 3D Surround is active, and turns white when 3D Surround is not active (normal stereo sound). See Soundbar Surround Mode Button, on page 8, for more information.
IMPORTANT: Do not connect the power supply’s AC cord to an AC outlet until you have made and verified all connections. Power Switch: Set this switch to the On position (press the switch’s white dot) to activate the soundbar. In normal operation, this switch will be left in the On position. See Turning the Soundbar On and Off, on page 8, for more information.
Volume Up/Down Buttons: Press the ( – ) button to reduce the volume; press the ( + ) button to increase the volume. Source Selector Button: This button switches between the sources connected to the Source 1 (analog) and Source 2 (digital) inputs. When Source 1 is active, the Source Indicator turns white; when Source 2 is active, the Source Indicator turns blue.
EQ Switch
Wireless Code Switch
Trim Switch
Source 2 Connection
Source 1 Connection
Power Switch
Power Connection
4 Page 4 of 30
harman/kardon
SB 15/230 Service Manual
ENGLISH
Subwoofer Rear- Controls
CROSSOVER
Crossover Knob VOLUME
Volume Knob MIN
MAX
0
PHASE 180
Phase Switch
POWER
Wireless Code Switch
ON
AC Fuse
OFF
Power Cord Power Switch
AC Fuse: The SB 15SUB is factory-equipped with a T1AL/250V 1A – 250V AC fuse. If the fuse ever blows:
Crossover Knob: This knob adjusts the subwoofer’s crossover between 50Hz and 150Hz.The higher you set the Crossover knob, the higher in frequency the subwoofer will operate and the more its bass will “overlap” that of the soundbar. This adjustment helps achieve a smooth transition of bass frequencies between the subwoofer and the soundbar for a variety of different rooms and subwoofer locations. See Subwoofer Crossover Knob, on page 9, for more information.
1. Unplug the power cord from the wall. 2. Use a screwdriver to remove the blown fuse. 3. Replace the fuse with an identical T1AL/250V 1A – 250V AC fuse.
Volume Control: Use this control to balance the subwoofer’s volume with that of the soundbar. Turn the knob clockwise to increase the subwoofer’s volume; turn it counterclockwise to decrease the subwoofer’s volume.
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE THE FUSE ONLY WITH THE SAME TYPE AND RATING. Power Cord: Plug this cord into an active, unswitched AC outlet. See Power Connections, on page 7, for more information.
Phase Switch: This switch determines whether the subwoofer driver’s pistonlike action moves in and out in phase with the speakers in the soundbar. If the subwoofer were to play out of phase with the soundbar speakers, some of the sound waves produced by the subwoofer or soundbar could be canceled, reducing bass performance and sonic impact. This phenomenon depends in part on the relative placement of the speakers in the room. See Subwoofer Phase Switch, on page 9, for more information.
Power Switch: Set this switch to the On position to activate the subwoofer. In normal operation, this switch will be left in the On position. See Turning the Subwoofer On and Off, on page 8, for more information. Status Indicator (on top of unit, not shown): Lights blue when the subwoofer's power switch is in the On position; lights amber when the subwoofer is in Standby; turns off when the subwoofer’s Power switch is in the Off position.
Wireless Code Switch: Selects between four different channels for the wireless subwoofer signal. IMPORTANT: Be sure to set the soundbar’s Wireless Code switch to the same channel as you set the subwoofer’s Wireless Code switch. See Wireless Code Switches, on page 9, for more information.
5 Page 5 of 30
harman/kardon
SB 15/230 Service Manual
Programming the Soundbar to Respond to Your TV Remote You can program the soundbar so it will respond to your TV remote’s Power, Mute, Volume Up, Volume Down and Source commands. This lets you control your whole home theater system with a single remote. Before beginning to program the soundbar, have your TV remote handy. We recommend sitting down in front of the soundbar. The steps will time-out, so read through the entire procedure before you begin.
3. Aim the TV remote at the front of the soundbar from about 300mm-900mm (about 12-36 inches) away.
300mm-900mm 12"-36"
To program the power command: 1. With the soundbar turned on, hold down the soundbar’s Power and Source Selector (SRC) buttons together until all the soundbar button indicators flash. This enters the learning mode. Hold down both buttons until all indicators flash
TV Remote
4. Hold down the TV remote's Power button for one second, then release it. Do this a total of four (4) times. When the soundbar has learned the power command, its Power Indicator will turn blue, and the Surround Mode and Source Selector Indicators will flash blue. •• If the Power Indicator flashes amber, the procedure failed. Repeat Steps 1 – 4.
To program the source, volume + and volume – commands:
2. Momentarily press the soundbar’s Power button. It will turn amber.
Follow Steps 1–4 as above, but in Steps 2 and 4, substitute the soundbar and TV remote’s Source Selector and Volume Up/Down buttons for the Power buttons.
Momentarily press
To program the mute command: Follow Steps 1-4 as above, but in Step 2, hold down the soundbar's Power button for 2-3 seconds. In step 4, substitute the TV remote's Mute button for its Power button.
To erase all remote programming: Hold down the soundbar's Surround Mode and Volume Up buttons at the same time for 2-3 seconds.
10 Page 6 of 30
SB 15/230 Service Manual
Troubleshooting If the soundbar does not turn on:
The soundbar won’t learn your TV remote’s commands:
•• Check that the soundbar power supply’s AC cord is plugged into a working AC outlet, and that the power supply is plugged into the soundbar.
•• Carefully follow steps 1 – 4 of Programming the Soundbar to Respond to Your TV Remote, on page 9.
•• Check that the soundbar’s Power switch is in the On position.
•• Hold the TV remote 12 inches (300mm) in front of the soundbar during the learning procedure.
If the subwoofer does not turn on:
•• Although the soundbar will learn commands from most TV remotes, there may be some IR codes that it cannot learn.
•• Check that the subwoofer’s power cord is plugged into a working AC outlet. •• Check that the subwoofer’s Power switch is in the On position.
If you press your TV remote’s Power button and the soundbar turns off when the TV turns on (or vice versa):
•• Check if the subwoofer’s AC fuse has blown. See Subwoofer Rear- Controls: AC fuse, on page 5, for instructions on checking and changing the fuse.
•• Press the Power button on either the soundbar or the TV (but not both) one time. This will put them back in sync so they will turn on and off together when you press the TV remote’s Power button.
If there is no sound coming from both the soundbar and the subwoofer:
•• Check that the soundbar is on (the Power Indicator is illuminated blue). •• Check that the cable connecting the TV or other source component to the soundbar is properly connected at both ends. •• Check that the soundbar’s Source Selector is set to the correct source (the Source Indicator illuminates white for Source 1 – analog, and illuminates blue for Source 2 – digital), and that the source is playing an audio signal. •• Check that the system is not muted (when the system is muted, the soundbar’s Power Indicator flashes blue). Momentarily press the Power button to un-mute the system. •• Check that the soundbar’s volume is not turned all the way down (the lowest setting of the Volume Down button will mute the system). If there is no sound coming from just the subwoofer:
•• Check that the Subwoofer Volume Control is not turned all the way down (fully counterclockwise). •• Check that the Wireless Code switches on the subwoofer and soundbar are both set to the same setting number. •• Move the subwoofer closer to the soundbar. (The maximum wireless operation distance is 50 feet (15.3m). If the soundbar’s sound is distorted:
•• Set the soundbar’s Trim switch to a lower setting. •• Check the source component to see if the distortion is coming from it, and not the soundbar. If the system’s sound is too quiet, even when the soundbar’s volume is turned all the way up:
•• Set the soundbar’s Trim switch to a higher setting. •• If the TV or source component is connected via a variable output, check its instructions to be sure that the output is not turned down too low. The bass output is not loud enough:
•• Turn up the subwoofer’s Volume knob. •• Move the subwoofer into a corner of the room. •• Move the subwoofer closer to the seating location.
11 Page 7 of 30
ENGLISH
harman/kardon
harman/kardon
SB 15/230 Service Manual
Specifications SB 15/230 System Frequency Response 50Hz–20kHz SB 15CNTR Soundbar
SB 15SUB Subwoofer
Input Rating DC 24V, 2.5–2.7A
Input rating: AC 230V, 50Hz, 100W
Amplifier Power 25 watts x 2
Amplifier Power 100 watts RMS
Tweeter Two 3/4" domes (one per channel), video-shielded
Woofer 10" cone, vented enclosure
Midrange Four 3" drivers (two per channel), videoshielded Dimensions (H x W x D) 110mm x 920mm x 89mm (4-5/16" x 36-1/4" x 3-1/2")
Dimensions (H x W x D) 480mm x 380mm x 380mm (18-7/8" x 13-3/8" x 13-3/8")
Weight 8 lb (3.6kg)
Weight 34 lb (15.4kg)
Harman Consumer Group, Inc. 8500 Balboa Boulevard, Northridge, CA 91329 USA 516.255.4545 (USA only) www.harmankardon.com Made in China ©2009 Harman International Industries, Incorporated. All rights reserved. Features, specifications and appearance are subject to change without notice. Harman Kardon is a trademark of Harman International Industries, Incorporated, ed in the United States and/or other countries. Designed to Entertain is a trademark of Harman International Industries, Incorporated. Part No. 406-000-06124-E
12 Page 8 of 30
harman/kardon
SB 15/230 Service Manual
NEW SECTION FOR THE SB 15 OWNER’S MANUAL. SB 15/230 How to Switch the system on: Manually: If the SB 15/230 is manually put into Standby on the ON/OFF Button on the SB 15 unit itself, it can only be switched back ON by manually pressing the ON/OFF button again. Auto Turn on: The SB 15/230 automatically enters Standby‐mode after approx. 15 minutes if no audio signal is detected. This can also be forced by learning (for example) the TV set’s remote control “Off” code into the SB 15/230 (See owner’s manual). Due to Power saving regulations, the SB 15 does not “listen” to the Audio Inputs, unless it senses a remote signal first, which can be any kind of remote signal (it does not have to be a learned remote code ‐ turning ON the TV or sending any other infrared remote code will be enough). The remote signal will tell the SB 15/230 to start up automatically as soon as audio is detected on (first) the Digital or (second) the Analog audio Input. If no signal is detected by the Inputs, the SB 15 will go back into total Standby again after approx 15 minutes. MATRIX OF ON/OFF FUNCTIONS.
Power OFF function
SB 15 Status
Way to Power On
Manual Power Off Button on SB 15 unit
Music sense OFF. Remote sense OFF.
Manual Power On Button only!
Auto Standby (Automatic if audio is Off or not present for more than 15 min)
By remote control (usually TV Remote, but any remote will do).
Music sense OFF, Remote sense ON.
Music sense OFF, Remote sense ON.
SB 15 switches music sense ON by IR signal, then powers ON 5-10secs after music is sensed on either (first) digital or (second) anaputs. Or press SB 15 manual Power button. SB 15 switches music sense ON by IR signal, then powers ON 5-10secs after music is sensed on either (first) digital or (second) anaputs. Or press SB 15 manual Power button.
Comment Remote sense is OFF to avoid unit powering ON. IR Activity from any remote (TV/SAT/VCR/DVD/...) sensed by the SB 15 switches the music sense ON. There is no need to learn any remote code to do this.
IR Activity from any remote (TV/SAT/VCR/DVD/...) sensed by the SB 15 switches the music sense ON. There is no need to learn any remote code to do this.
Page 9 of 30
harman/kardon
SB 15/230 Service Manual
Page 10 of 30
harman/kardon
SB 15/230 Service Manual
Page 11 of 30
harman/kardon
日 期
版 本
頁 次
0
1
2009/12/25
客 戶:JBL
作 業 指 示
SB 15/230 Service Manual
機 種:SB 15CNTR/230
Harman/Kardon SB 15/230 Center Exploded View
螺絲均要點膠
Rear Enclosure
013-7600-05766-E 352-AM04008C1334-E 315-ABS-05230-0BAE 247-030-05099-0BAE
1 16 1 1
Side Cap
305-ABS-05037-0BAE
2
315-ABS-05231-0BAE 32DM20AX-HT03-E
1 2
Crossover Screw for woofer
Top
Gasket
214-000-05409-0BAE
4
Gasket
214-000-05408-0BAE
4
Gasket
398-ABS-05062-E
2
Insulation foam
328-000-05855-0WAE
2
Amplifier
010-0N25-05265-E
1
Foot
320-NBR-05214-0BAE
2
LOGO
316-AG-00556-0VAE 32PF55JZP-PW02-E
1
Grille 名 稱
Woofer
依ECN No.
更改
依ECN No.
更改
依ECN No. 091043
4
Bottom Tweeter
編 號
352-AM03008C1086-E
22
Crossover
013-7600-05766-1E
1
Baffle
243-030-05259-0BAE
1
Screw for Amplifier
352-AM03510D112-E
20
329-030-05464-0BAE
1 數量
料
承 認 更改
號
確 認
製 作
蔣國正 蔣國正
保存年限: 永久
Screw for crossover
蔣國正 Page 12 of 30 表單編號:DM-4-D-013 1版
harman/kardon
日期
版本
頁次
2009/12/03
0
1
客 戶: 機 種:
作 業 指 示
SB 15/230 Service Manual
Harman/Kardon SB 15/230 subwoofer, Exploded View 1 2
3
4
5 6 7
序號 品名 料號 數量 Screw for 1 amplifier 352-AM04020D210-E 10 8 2 Amplifier 010-7610-05246-E 1 務 3 Wood 1 Cabinet 241-100-00613-2BCE 注:1.銘板( 316-AL-00553-E)背後點3188膠水 Logo 316-AG-00557-E 4 1 再貼到鐵網卞槽中 Logo fot 5 grille 316-AL-00553-E 1 2.銘板( 316-AL-00553-E)的位置是:銘板下端距 6 Woofer 25PF12DZB-FW01-E 1 靠LED 燈的箱體邊緣60mm, 左右居中 for 352-FM04020D605-E 7 Screw 5 woofer Rubber 320-RUB-00057-0BAE 8 Foot 4 3 2
承認
1 0
ISSUE
確認
初版發行 REVISIONS
DATE
制作 蔣國正 2009/12/03
NAME 表單編號:
Page 13 of 30
版
harman/kardon
SB 15/230 Service Manual
Harman/Kardon SB15 Soundbar with wireless subwoofer. System Parts list. SB15 Center
Part Number 013-7600-05766-1E 352-AM03008C1086-E 32DM20AX-HT03-E 315-ABS-05231-0BAE 305-ABS-05037-0BAE 247-030-05099-0BAE 315-ABS-05230-0BAE 352-AM04008C1334-E 013-7600-05766-E 32PF55JZP-PW02-E 316-AG-00556-0VAE 320-NBR-05214-0BAE 010-0N25-05265-E 328-000-05855-0WAE 243-030-05259-0BAE 329-030-05464-0BAE
SB15 Sub
Part Number 352-AM04020D210-E 010-7610-05246-E 241-100-00613-2BCE 316-AG-00557-E 316-AL-00553-E 25PF12DZB-FW01-E 352-FM04020D605-E 320-RUB-00057-0BAE 051-A05264D-E 051-A05264C-E 051-A05264B-E 051-A05264A-E 302-FE-05275-0BAE 150-E0764201-E 152-V60202603-E 154-V09006T0-E 155-520020-E 162-50652003-E 180-P3024DB-E 306-ABS-05082-0BAE 323-AL-05184-0LAE 335-NYL-00002-0BAE 311-ABS-00028-0BAE
Accessories and package
Part Number 151-E1105301-E 165-020001101-E 376-000-01249-0BAE 403-000-05796-E 435-000-05196-E
Part Description Crossover Screw for Crossover Tweeter Bottom Side Cap Rear Enclosure Top Screw for woofer to rear enclosure Crossover Woofer LOGO Rubber Foot Amplifier Insulation foam Baffle Grill Part Description Screw for Subwoofer Amplifier SB15/230 SUB Wood Cabinet Harman Kardon Logo for the Sub top board Logo for grille 10" Subwoofer Screw for woofer to wood cabinet Rubber pad for subwoofer cabinet STANDBY POWER PCB ASSY SB15 SUB WIRELESS PCB ASSY SB15 SUB DIGITAL POWER AMP PCB SB15 SUB PREAMP PCB ASSY SB15 SUB Subwoofer Amplifier Transformer Power Cord Fuse Fuse holder Speaker Wire Power Rock Switch Rear Enclosure Aluminum heat sink Power Cord Strain Relief Knob Part Description Power adapter Signal cable for Ext. Trigger input jack L brackets (2pcs) Accessory bag for Soundbar Accessory box for Soundbar Protective boards for Soundbar Page 14 of 30
harman/kardon
SB 15/230 Service Manual
431-000-07021-E 430-002-05391-E 431-000-07026-E 402-000-06333-E 406-000-06124-E 431-000-07022-E 283-001-05105-0WAE 424-000-00185-E 431-000-07023-E 398-000-00304-E 402-000-06334-E
EPE for Soundbar carton end Pearl-cotton bag for Soundbar EPE for Soundbar mid-carton Gift Box for Soundbar Cntr Owner Manual EPE Material for Subwoofer (top) Non-woven cloth bag PO bag EPE Material for Subwoofer (bottom) Drier Gift Box for SB15 Sub/230
Page 15 of 30
harman/kardon
SB 15/230 Service Manual 1
2
3
4
C06 100n
VCC
VCC
C30 100n
R16 82.5k
R04
14
D
15.4k 11
12
U1D TL074CD
10 VR2B VR*2
VR2A VR*2
C
C04 33n
8
C08 100n
R05
2
C03 100p
24.9K
VCC
VSS
R15 82.5k
C09 100n
SGND
CON2 1 2 3 4 5
OUT 2
SGND
7
VSS 4
5
4
VCC
U2A TL072CN
VSS
6 SGND
mout
VCC
8
SGND
C15 100n
R09 220k
1
1
3
U1C TL074CD
VSS
A
8
9
R02 17.8k
11
13
R11 12.1K
4
4
A
VCC VR1 A50k
4
R12 12.1K
U2B TL072CN
Header 5
6 R01 22K
5 4 3 2 1
C01 10u
5
C02 220P
SGND
VSS
7
B
SGND
U1B TL074CD
+12VC
VCC 1
OUT IN GND
VSS R08 22K
Header 5
R06 18.7k
VCC
B
U5 MC78L12
VSS
C11 100u
4
C12 100n
3
2
VCC CON1
11
B
C13 100n
2
U1A TL074CD
mout R10 10K
VSS
C
3 sw1 6 1 4 Netsw1_3 2 5 SW2-2
C16 10u
R17
U4
6.8k
8
R18 3.3k
R07 C05 VCC 220p
C18 220n
10k
C27 22n
8 VCC
SGND
C22 4.7u
C34 4.7u
C37 4.7u
C26 4.7u
C36 4.7u
C25 100n
C21 100u
5
C32 100u
SGND
2
4
C23 4.7u
6
C35 100n
VSS
3 4 6
R21 8.25k
7
C17 10u
5 C38 220n
U3B TL072CN
INb
OUTb
INa
OUTa
INT
SW
SENCE V+ Vref
GND
R19 24.9k
SGND R20 14.3k
9 2 7 1
C C29 VCC 220p
C28 4.7u R22 22k
R23 47k
8
SGND
R03 10K
2
10 3
1 OUT
1
NJM2761-10 SGND
U3A TL072CN
4
1
A
11
3
SGND SGND
VSS
VSS
CUSTOMER:JBL MODEL:SB 15SUB/230 BOARD: PERAMP DETA:SEP.01.2009 PAGE 2/5
D
1
2
APPROVED
3
CHECKED
CHECKED PREPARED
REV 1.0
4
Page 16 of 30
D
1
harman/kardon
2
3 CON1 Header 8
1
BD
C13 470u/16V
C14 100n
GND VCC R07 R09 R11 R14 R16 R18 R20 R22
MD1 C07 1000u/10V R04 4.7R
D01 SCD14 GND
GND
C03 100n
C04 10n
C05 100n
C06 10n
RX M1087 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
U02 STM809
GND 8 GND
GND
20K 20K 20K 20K 20K 20K 20K 20K
6 5 4 3 14 13 12 11 10
SW1 5 4
B
C02 1000u/10V
1
GND
rest
2
nRESET Vss
Header 3
VCC
C01 100n
R03 47k
Vcc
link1 BD1 2
3
VCC
3 2 1 A
1 2 3 4 5 6 7 8
VCC CON2
4
SB 15/230 Service Manual
R01 4.7R
R24 10K
U03
H G F E D C B A SI
2 15 1
3
7
QH
9
QH
CLK CLK INH S/L VCC
2 1
R08 VCC R10 R12 R15 R17 R19 R21 R23 GND
GND 20K 20K 20K 10K 20K 20K 20K 20K
8
C15 100n
SN74HC165D
U04
H G F E D C B A SI
2 15 1
VCC 16
VCC1
GND
6 5 4 3 14 13 12 11 10
QH QH
CLK CLK INH S/L VCC
R45 100R R44 100R
7 9 R13 100R
VCC 16 C16 100n
SN74HC165D
GND
SEL GND R25 33R
GND C17 100n
GND
C19 150p 8
C18 470u/16V
AGND
VCC BD2 1
R35 3.9k
GND
BD
C23 1n
2 R33 4.7K
C21 100n
R36 33R
C39 open
1 3
R28 10k
C20 1000u/10V C25 10u
AGND
VSS
link1 16 15 14 13 12 11 10 9
C26
VCC1 U05B NJM4560 8
R37 33R AGND
C27 150p
R39 20k
10u R40 10k
R41 3.9k
R42 10k
R43 10k
C28 10u
MUTEC /RST AOUTL SDATA AV SCLK/DEM1 AGND LRCK AOUTR MCLK REF_GND DIF1 VQ DIF0 FILT+ DEM0
C31 1n
C32 100n
AGND
AGND
AGND
VSS D AGND
AGND
C22 0.22u GND
1
R50 47k
VCC
R48 510
1 2 3 4 5 6 7 8
rest
Q04 8550S
CON4
R47 510
Q02 8050S Header 2 Q03 8050S R52 47k
C30 10u
C
Q01 8050S
C34 C35 C36 C37 AGND open open open open GND
GND
4
5 C24 100n
R49 20k
CS4340
7
C33 470u/16V
R51 47k
link1
R29 R30 100R 100R
C29 100n
6 VSS
R31 R32 100R 100R
2 1
AGND
Header 5
GND
U06
CON3 1 2 3 4 5
B
AGND
4
C
GND
C38 open
A
Rx M1087 C40 open C41 open
R27 20k
U05A NJM4560 2
GND
RFVcc RFGND GND Vcc /RST PB1(CS0) MSIO0 MOSI0 SCK0 PF0(ID_DATA) PF1(ID_CLK) PC0(ID_LATCH) /PC1(MUTE_LED) /PC4(BOND_LED) PC5 MCLK PC7(I2C_SDA) PI0(I2C_SCL) LRCK PI2 AGND1 SDOUT SCK AGND2 AVdd
AGND
2
CUSTOMER:JBL MODEL:SB 15SUB/230 BOARD: WIRLESS DETA:SEP.01.2009 PAGE 3/5
APPROVED
3
CHECKED
CHECKED PREPARED
4
REV 1.0
Page 17 of 30
D
harman/kardon
SB 15/230 Service Manual
1
2
3
4
5
VDDA2
R05 30.1k
C23 1n
8 11
R14 5.6k
B
100n C19
100n
100n
6
R07 10R
17
C18
C13 470p
C14 470p
L01
IN1-
C25 1n
C26 1u
7
U1 9
SUB
C09 220u/25V
12
C20 1u
OSC
DZ1 5.6V
R10 5.6k
VSSA1
MODE
10
SGND
D02 1N4148 Q06 8550S
MODE
C17 100n
C15
R06 30.1K
C16 100n
Header 5
R03 24k
C10 2.2u
47u/100v
16
OUT1
VSSP1
-15v VCC
VSSP A
C12 100n
14
SUB
Header 6
R04 10K
VSSP VDDP
1 2 3 4 5
8
C11
VDDP1
+15v
VDDA1
+3.6V
VDDP VSSA2
MODE
1 2 3 4 5 6
A
VSSA2
7
CON2
CON1 std
6
2 33uH
1
BD
BOOT1
C28 120n/63V
15n
C29 470n/63V C32 330p
TDA892XBTH
SUBOUT+ R13 22R
C27 15
IN1+ SGND1
BD4
2R2 R24
C33 100n
C63 330p B
C62 6.8n
4
C30
SGND
Q03 8050S
C31 100n
C50
CON4 3 2 1
3 2 1
R21 0R
R15 1.3K
C36 22u/35v C42 22n
C61 6.8n
15n
VSSP2
VDDP2
L02 2
21
OUT2
33uH
20
23
STABI 18
CON2
C51
C52
100n
100n
C57
C58
100n
100n
1
BD C49 470n/63V
C45 120n/63V
R19 10R
BD6
C46 330p
C59 470p
SUBOUT22R R17
2R2 R23
C55 100n
C64 330p
C60 470p
C
BR1 Bridge1 VDDA2
C65 2.2n
C40 22u/35v
C48 100n
C66 2.2n C38 22n
VSSD
C56 100n
100n
C35 100n
C
24
C53 220p
220u/25v C34 100n
19
PROT 13
IN2+
3
5
680R
22
BOOT2 N.C.
+15v
C22 1n
1 2
C39
IN2-
R09 15K
R12
C24 6800u/35v
SGND2
VSSA2
+15v
100/2W R11 4.7K
C21 100n
2
1
Q02 D882
R08
D01 1N4148
CON3
VCC
VDDA2
VCC
C41 100n
DZ2 R16 15K C44 220u/25v
R18
C43 6800u/35v
C01 470u/35v
680R
2
VCC
BD1
C04 BD 100n
C54 100n
VDDP
VSSA2 C02 470u
1
VSSP
R01 VDDA2
C05 100n
VSS
VDDP
VSSP
C03 470u/35v
10R
2
VDDP
BD2
C06 BD 100n
VSSP
VSSP
R02
1
VSSA2 C07 100n
10R C08 470u/35v
R20 4.7K R22 100/2W D
-15v
-15v
Q04 B772 VSS
1
2
3
CUSTOMER:JBL MODEL:SB 15SUB/230 BOARD: POWER AMP DETA:SEP.01.2009 PAGE 4/5
VSS
4
5
APPROVED
6
CHECKED
CHECKED PREPARED
7
REV 1.0
8
Page 18 of 30
D
harman/kardon
SB 15/230 Service Manual 2
C01 15uf/400V
D01 1N4007
R01 300k
4
R02 300k
HI VOL
D09 UF302
TR1 1
R03 1.1meg
3
2 C13 47uF/16V
3
R22 open
4
C07 0.22u
5 OC
VCC OC GND
IS
CT FB THX203H
7
C16 10n
GND
TR
6
+3.6VA
5 R21 TRANSFORMER 0R op1 4
C18 R11 R12 22n 2R 2R
Q03 8050S
R10
R08 4.42K
1 C17 0.1u
PC817C
3
+3.6V
1 2 3
LED1 R09 10k
U01 ST TL431
GND
R14 10k
R17 680R
C
GND
std
100k
Q02 8050S R15 0R
GND
R18 0R
GND
R23 100k
HI OPERATIVE
OPEN:R05,Q01,R13,R18
LOW OPERATIVE
OPEN:R15,R16
GND
CUSTOMER:JBL APPROVED MODEL:SB 15SUB/230 BOARD: STANDBY POWER DETA:SEP.01.2009 PAGE 5/5
D
1
R06 10k
R07 510
2
std GND
R13 4.7k
1
1
2
CON3 Header 2B
B GND
R16 0R
C05 470u/16V GND
CON1 Header 3
L_OUT
2
C04 470u/16V C03 330pF
D08 1N4148
L_IN
N_IN
CON2 Header 2B
R05 100K
C11 0.1u
6
3 Q01 8050S
+3.6V
C09 0.1u
S1 S2
8
+12VB
C20 1000p
C
OB
C15 680P K1 Relay-SPST
W4
L1 Inductor 22uH
D02 UF302
1
1
1
+3.6VA
3 4 W3
C12 0.1u/25V
GND
7
U02
C19 1000p
C10 0.1u
C06 100u/25V
W2
ICSP D07 SF16
RV1 14D471K
+12VB
A
D06 1N4007
B
A
+12VA
6 D05 UF1010
R04 1.1meg
L02 8mH
R20 open
8
C08 W1 470PF/1k 2
D04 1N4007
4
2
D03 1N4007
R19 68 ohm
K
A
3
2
1
2
3
CHECKED
CHECKED PREPARED
REV 1.0
4
Page 19 of 30
D
harman/kardon
SB 15/230 Service Manual
Page 20 of 30
harman/kardon
SB 15/230 Service Manual
Page 21 of 30
harman/kardon
SB 15/230 Service Manual
Page 22 of 30
harman/kardon
SB 15/230 Service Manual
Page 23 of 30
harman/kardon
SB 15/230 Service Manual
Page 24 of 30
harman/kardon
SB 15/230 Service Manual
Page 25 of 30
harman/kardon
SB 15/230 Service Manual
Page 26 of 30
harman/kardon
SB 15/230 Service Manual
Page 27 of 30
harman/kardon
SB 15/230 Service Manual
Page 28 of 30
harman/kardon
SB 15/230 Service Manual
Page 29 of 30
harman/kardon
SB 15/230 Service Manual
Page 30 of 30