Texas Instruments Tech Day 2007
“TI Solutions for LED Lighting”
Setting LED Current
Voltage Controlled
Current Controlled
Cheap
More expensive
Simple
Excellent regulation
Extremely Poor regulation
Multiple LED Configurations
Easiest to implement and Control Limited by converter topology or possibly Safety voltage limitations Current matching
Low Cost Poor Regulation Lossy w/o Op Amp
Best Parallel Control Most Expensive Need matching MOSFETs Linear (lossy)
Analog vs PWM Dimming
Analog Changing the LED’s DC current changes LED intensity i.e.,25% brightness by running a 400mA LED at 100mA Implemented with digital programming of IC or with an external voltage PWM Changing duty cycle of applied current i.e., 25% brightness by running 400mA for only 25% of the time. PWM frequency should be greater than response time of human eye (approx 60Hz) Implemented with PWM of IC enable or external voltage
400mA 300mA
Analog Dimming
200mA 100mA
400mA
PWM Dimming
300mA 200mA 100mA
0.25T
T
Solutions to Challenges TI DC to Constant Current LED Driver Examples TPS63000 Low Power Or Single HB LED
Buck/Boost Driver TPS61050 – LED Flash Driver TPS61081 – Boost Driver TPS61200 – Ultra Low Vin TPS62050 – 800-mA 10V Vin TPS62100 – 500-mA, 9V Vin TPS40K
High Power
– DC Adjustable Current HB LED Driver TPS5430 – DC Integrated FET HB LED Driver TPS43000 – Multi-Topology HB LED Driver UCC280x – 24Vin Boost HB LED Driver
Boost Converters: (Integrated Switch) Products 0.3 0.8 0.9
1.8V
2.5V
2.7V
Input Voltage 3.3V 4.5V 5.5V
4.5A
TPS61030 HERO
TPS61050
2.0A
TPS61029
1.0A 0.8A 0.7A 0.6A 0.5A 0.4A
Switch Current Limit
1.1A
1.5 to 5.5V 3.0V, 3.3V
TPS61120 +LDO TPS61130
dual
HERO
800mA WLED Flashlight Driver 2.5 to 5.5V 3.3V, 3.6V 2.5 to 5.5V 3.3V 28V
TPS61080
12V
17V
• High Efficiency • Small Solution Size • High VOUT &
1.8 to 5.5V 3V, 3.3V, 5V 1.8V to 5.5V
TPS61059 TPS61100 +LDO
dual
10V
KEY CAREABOUTS:
Buck Boost
TPS61020 TPS61200
HERO
9.0V
1.8 to 5.5V 3.3V, 5V 2.5 to 5.5V 1200mA WLED Flashlight Driver
1.8 to 5.5V
TPS63000
1.5A
1.2A
1.8V to 5.5V 3.3V, 5V
TPS61090
1.8A
1.3A
6.0V
High IOUT
HERO
500mA WLED Driver 1.5 to 3.3V 1.5V, 1.8V, 2.5V, 2.8V, 3.0V, 3.3V
TPS61058 TPS61000, TPS61010
TPS63700
up to -15V INVERTER 1.8 to 5.5V
TPS61028 dual
TPS61140 LED+LED
each output up to 27V, single Inductor
dual
TPS61150 LED+OLED
each output up to 27V, single Inductor
TPS61070 TPS61001/2, TPS61011/2
TPS61145 with EasyScale Interface (Feb.2007)
1.8 to 5.5V 1.5 to 3.3V 1.5V, 1.8V, 2.5V, 2.8V, 3.0V, 3.3V
TPS61081 TPS61040 TPS61060 CSP
28V 1.8 to 28V 14.5/18.5/23.5V
Boost only Buck/Boost
TPS63000 Family 96% Efficient Buck/Boost Driver Key Features
unique Efficiency performance
Input Voltage: 1.8-V to 5.5V Output Voltage: 1.2V to 5.5V, 3.3V, 5.0V Output current Switch: 1.7A up to 1200mA output current in Buck configuration @ 3.3V up to 800mA output current in Boost configuration @ 3.3V
Efficiency: 96% over wide Vin range (max) Package: 3x3 QFN Automatic Transition between Step Down & Boost Mode Device Quiescent Current less than 25-µA Power Save Mode for Improved Efficiency at Low Output Power Forced fixed Frequency Operation possible Load Disconnect During Shutdown Over-Temperature Protection
Focus Applications 2-Cell and 3-Cell Alkaline, NiCd or NiMH or SingleCell Li Battery Powered LED Equipments
Benefits Smallest solution size, requires only 2.2uH Inductor s input voltages as low as 1.8V (for 2-cell Alkaline) Highest efficiency over wide Input range
small Inductor low Vin !
Battery Powered Buck-Boost LED driver
Actual design used by Cree for demonstration board
TPS61050 1.2A High-Power DC/DC Boost Converter with I2C Focus Applications Torch White LED supply General lighting applications
small Inductor L
VIN
2.2µH GND
Ambient Lighting
SW SW
VOUT
COUT 10µF
AVIN P
CIN
Barcode Readers
P P
LED
Key Features Input Voltage: 2.5 to 6.0V
I2C I/F
I2C
Interface
SCL SDA FLASH_SYNC
Output Voltage: Vin to 5.5V AGND
Switch Current Limit: 2A (max) Quiescent Current: 8.5mA Shutdown current: 1.3uA (max) I2C Compatible Interface (up to 400kbps) Five Operational Modes Integrated Over-Voltage Protection (OVP)
LED Disconnected in Shutdown Integrated Current Limit, Short-Circuit Protection and Thermal Shutdown Package: 12-bump WCSP or 3x3 QFN-10 Total Solution Circuit Area < 25 mm2
up to 5W output !
GPIO
PGND PGND
P
Benefits Smallest Total Flashlight Solution Size ! 2MHz switching frequency allows the use of small, low profile 2.2µH inductors. s up to 5W !
Options: TPS61050: TX Masking Input TPS61052: Hardware Voltage Sel.Mode TPS61054: GPIO pins
TPS61080/1 High Vout Boost Driver The differential feature of the device is high reliability. The device can protect itself and external components when there’s short between any pins and between any pin to ground. Key Features
Focus Applications
Benefits
Input Voltage: 2.5V to 6.0V
LCD Bias supply
Smallest solution size
Output Voltage: up to 27V (max)
OLED Bias Power Supply
Highest Efficiency
Switch current Limit:
White LED backlight
0.5A (TPS61080)
White LED flashlight
Several Protections Circuits
1.3A (TPS61081)
Efficiency: 85% (max) 10 pin 3x3mm QFN package Input-to-output isolation great for medical Short circuit protection Overvoltage protection
Thermal protection Adjustable Softstart Integrated power diode 600kHz or 1.2MHz fixed switching frequency
TPS61200
0.3V Input Voltage Synchronous Boost Driver Key Features Input voltage: 0.3V to 5.5V Startup into full load at 0.5V input voltage 1.8V to 5.5V output voltage
Applications 1-/2-/3-cell alkaline, NiCd or NiMH battery or 1-cell Li battery powered lamps
Switch current limit: 1.5A (max)
Single-solar cell & micro-fuel cell powered lamps
More than 90% efficiency at:
Portable solar charger
600mA output current at 3.3V (VIN ≥ 1.2V) 600mA output current at 5V (VIN ≥ 3.3V)
Quiescent current: < 55µA Package: 3x3 QFN
Benefits Integrated ‘DownMode’ enables continues operation during VIN > VOUT conditions Automatic transition between Boost mode & Down Conversion mode Load disconnect during shutdown
Perfect for Single Cell Alkaline Torch
TPS62050 800-mA, 10V Vin, Step-Down Driver Benefits
Key Features 2.7V to 10V (11Vmax) input voltage range Up to 800-mA output current, up to 95% efficiency 12-uA (typ) quiescent current, 2-µA shutdown PFM power-save mode for light loads 850-kHz (typ) operation, synchronizable to external clock up to 1.2MHz Forced-PWM mode available Power Good and low-battery detect Soft-start limits in-rush current MSOP-10 package
Suitable for 3- to 6-cell alkaline or 1- to 2cell Li-Ion as well as 9-V wall adapter applications Conserve battery capacity, limit heat dissipation small inductors – 10µH reduces noise
Why Buy Industry’s best combo of high efficiency, low power and output current
LED current = VFB / R1
TPS62100 Family 500mA, 9V Vin Step-Down DC/CC Benefits
Key Features 2.5V to 9V Input Voltage Range 500mA Output Current Switching frequency: 300kHz, 600kHz, 1MHz, 2MHz 100% Duty cycle for lowest dropout PWM/PFM operation for highest efficiency over wide load current ranges External Synchronization 8 pin SOIC
Suitable for 3- to 6-cell alkaline or 1- to 2-cell Li-Ion as well as 9-V wall adapter applications Conserve battery capacity, limit heat dissipation small inductors Multiple frequency options available for choice in size or efficiency constraints
• LED current = VFB / R1
TPS40200 Wide Input, Low Pin Count Driver
Key Features 4.5V to 52V operation Voltage Mode Control with Feed Forward Compensation 700mV Voltage Reference - 1% accuracy Internal Under-Voltage Lockout Programmable Frequency (35kHz-500 kHz) Programmable Overcurrent Protection Frequency Synchronization Closed Loop Soft Start Integrated Driver Package - 8 pin SOIC
1
RC
2
SS/SD
3
COMP
4
FB
TPS40200
VIN
VIN
8
ISNS
7
Rsense
GDRV 6
GND
VOUT
5
Benefits
Wide input range for use in many applications Voltage feed forward – great line regulation, fast transient response Programmable features allows flexible design; frequency, overcurrent protection, under voltage lockout Softstart provides smooth, well controlled power up Simple configuration- minimal external components
Adjustable Current HB LED Driver
Wide Vin Buck Boost LED Driver
Built and tested with Avago ADJD-MJ50/51 & ADJD-MJ60/61
TPS5430 - 5.5V to 36V Input, 3-A Step Down LED Driver
Benefits
Features
Integrated 110mΩ N-channel MOSFET Fixed 500kHz Switching Frequency Output Voltage to 1.23V with 2% accuracy Internal Slow Start Circuit Internal Compensation Enable Pin Current limit & Thermal Shutdown Only 17uA Shutdown Quiescent Current -40C~125C Operating Junction Temp. Thermally Enhanced 8 pin HSOIC SWIFTTM Software Tool
High Efficiency Up to 95% Small Output Inductor & Capacitor High Performance Limits Start-up Inrush Current Reduced External Components Easy On/Off Control Self-Protected from Fault Conditions Low Power Consumption when Switched Off Reliable & Robust at Extreme Temperatures Small with Good Thermal Performance Quick & Easy Design www.ti.com/swift
Driving High Current LEDs with the TPS5430 4 LEDs @ 500mA
Features
Wide Input Voltage Range: 5.5 V to 36 V Max 3A drive current Buck Converter Output up to 87% Vin Internally Compensated, eliminates components High Efficiency with Integrated 110mOhm MOSFET
TPS43000 Multi-Topology High Frequency PWM Controller Typical Sync Buck
Features 2 MHz Switching Frequency Voltage Mode Control High Efficiency Synchronous Rectification Drivers Fully functional from 1.8V through 9V Works with Buck, Boost SEPIC & Flyback Topologies Fixed Frequency Operation or Pulse Frequency Modulation (PFM) Mode Built-In Soft Start Programmable Discontinuous or Continuous Conduction Modes
Typical Boost
Applications
2 to 4 Cell Alkaline or Nickel, 2 Cell Lithium Lamps High current boost from 5V wall adapter
TPS43000 LED Driver
Vin=1.8V to 8V 350mA LED current
UCC280x - Current Mode PWM Controllers Features
Top View Comp
100-μA Typical Starting Supply Current FB CS 500-μA Typical Operating Supply Current RC Operation to 1 MHz SOIC-8 Internal Soft Start Internal Fault Soft Start Internal Leading-Edge Blanking of the Current Sense Signal 70-ns Typical Response from Current-Sense to Gate Drive Output 1.5% Tolerance Voltage Reference Same Pinout as UC3842 and UC3842A
Ref Vcc Out GND
Part Number
Max Duty Cycle
Ref. Voltage
Turn-On Threshold
Turn-Off Threshold
UCC2800
100%
5V
7.2V
6.9V
UCC2801
50%
5V
9.4V
7.4V
UCC2802
100%
5V
12.5V
8.3V
UCC2803
100%
4V
4.1V
3.6V
UCC2804
50%
5V
12.5
8.3V
UCC2805
50%
4V
4.1V
3.6V
PWM controllers with Peak Current Mode or Average Current control methodology use a dual-loop control circuit to adjust the regulating pulse width in response to load changes. Current Mode controllers provide a fast transient response with built-in current limiting.
24Vin Boost LED Driver
General LED Lighting System Questions
LED Vf LED Current Number of LEDs LED configuration (series, parallel, series & parallel) Input voltage range Current Matching Requirements Efficiency Requirement Application (backlight, active display) Dimming (Y/N; Analog or PWM) AC/CC – Transformer Height Profile, PFC if > 25W, Isolation
Why current sink solution? DC-DC
LEDs are current driven devices. Any change and ripple in current visible
DC-DC
(1) DC-DC solution:
Vout
•High current ripple
•Low current accuracy between dc-dc ILED1
ILED2
•Price
ILED
•Slow rise time at high current, rise time depends on switching frequency of dc-dc
(2) Current sink solution: DC-DC Converter
VOUT
•Fast rise and fall time
VOUT
•High current accuracy from each channel to each channel
•Hight current accuracy from PWM pulse to PWM pulse •Only one power supply needed
ILED1 Current sink
ILED2
•Low cost
Current sink
•Low dc voltage possible ILED (1)
SOURCE: SLVS441B
(2)
3 TLC5940 in parallel
TLC59xx RGB LED Driver Portfolio KEY CAREABOUTS: HERO
≥10-bit + G/S
TLC5930
1024 G/S, 12 CH 24Pin HTSSOP
TLC5904
TLC5940
4096 G/S, 16 CH Dot Correction (EEPROM) 28 PIN DIP & TSSOP
TLC5941
• Display Quality • System Reliability
4096 G/S, 16 CH 28 PIN DIP & TSSOP
TLC5905
8-bit G/S 256 G/S, 8/16 CH 100 PIN HTQFP
Non G/S
256 G/S, 8/16 CH 64 PIN HTQFP
TLC5921
TLC5922
16 CH LOD 32 TSSOP
16 CH Dot Correction 32 TSSOP
TLC5923 16 CH LOD & Dot Correction 32 TSSOP
LOD: LED Open Detection
TLC5924 16 CH LOD & Dot Correction Pre Charge FET 32 TSSOP / QFN
TLC5924 Multiplexing LED Display Driver Applications
Benefits Fast data transfer rates Superior sharpness with 128 adjustable steps Increased system reliability with thermal shutdown & LOD Flag Integrated pre-charge FET for improving image quality & space savings with reduced component count Space saving high-power thin (PowerPAD) package
Features 16 Channels 7-bit (128 steps) Dot Correction Pre-charge FET 3.0V to 5.5V input voltage range Channel voltage up to 15V input 80mA Constant Current/Channel Chip to Chip Accuracy: 4% typ CH to CH Accuracy: 1%typ Two built-in Error flags (LED Open & Thermal error) Controlled in-rush current
Multiplexing type LED Display ( ½, ¼ … Duty Cycle ) In Door Display using Dynamic Scanning
Smaller, Highly integrated , Spike Noise free solution ideal for multiplex type LED display. 80mA Constant Current
Pre-charge FET HTSSOP (PowerPad)
TLC5924
QFN
TLC5924
4% Chip-Chip Accuracy
Multiplexing LED Display VLED
Scan-H
Scan-G
Scan-B
Scan-A
OUT0
GPIO
uC or DSP
OUT1
DATA IN
OUT14
DATA OUT
LED Driver 1
OUT15
OUT0
OUT1
DATA IN
OUT14
OUT15
DATA OUT
LED Driver 1
In low brightness, low current applications sequencing can be used to reduce number of LED-drivers. In above example 8 scan lines controlled by the control unit has been added. Each scan-line is a power source for a LED-line and will be multiplexed with the LED-driver.
Ghosting Ghosting is unwanted momentary illumination of LED Appears as affects in multiplex systems Mismatch in diode forward voltage Stray board capacitance Current spike in D2 when VLED1>VLED2
5V
+ VLED1-
- VLED2 +
5V GND
GND
Vout
TLC59xx
Stray board and Cable capacitance
TLC5940 RGB LED Driver w/Dot Correction & PWM Grayscaling Benefits
Applications
Superior display quality through PWM Grayscaling & Dot Correction Increased system reliability with LOD & Thermal Shutdown
Mono-color, Multi-color, Full color LED Displays LED Signboards Display Backlighting
EVM
Features
16 Channels 12-bit (4096 steps) PWM Grayscaling 6-bit (64 steps) Dot Correction 3.0V-5.5V Input Voltage Range 120mA Constant Current/Channel 30MHz Transfer Rate Chip to Chip Accuracy: 2.7% typ Channel to Channel Accuracy: 1%typ Integrated EEPROM
120mA Constant Current
EEPROM
TLC5940
TLC5940
2.7% Chip-Chip Accuracy TLC5941 - Low-cost TLC5940 w/o EEPROM
Why Buy High integration level; grayscale & Dot Correction; high accuracy; fast data transfer rates; wide input voltage range
PDIP
QFN
HTSSOP (PowerPad)
TLC5917 / 27 Constant Current LED driver Benefits
Programmable constant load current Fault reporting
Features 16 constant current sink outputs (0mA – 120mA) Current output programmable by external resistor Programmable current gain (8-bit) Current accuracy between channels ±3% (typ) Diagnostic → Open load (On) → Overload / Overtemperature (On)
Protection → Individual channel over-temperature shutdown Serial communications interface (4 wire, cascadable) Thermally enhanced packaging concept for efficient heat management (20 pin HTSSOP or QFN) Supply 3.3V or 5V
Applications LED illumination and intensity control
3.3v - 5V
Vsupply Vf
Vcc D0 NCS
D1
SCLK
D2
SDI SDO
TLC5917
D3
D4 D5
EN
D6
Ireg
D7
GND
R optional for Vsupply >Vf + 1V
Constant Current LED System Diagram DC/DC 5V
Mounted on PCB as autonomous Module
uC
5
Several modules combined for up to 500k points
5
5 Ireg
Ireg
Ireg
D0
D1
D2
D3
D4
D5
D6
D7
DC/DC Vsupply blue
Vcc
6xTLC5917
GND
D0
D1
D2
D3
D4
D5
D6
D7
DC/DC Vsupply green
Vcc
6xTLC5917
GND
D0
D1
D2
D3
D4
D5
D6
D7
DC/DC Vsupply red
Vcc
GND
6x TLC5917
RGB Video Wall Power Supply
Power Modules are the most popular means of driving LEDs
PTV Series of Vertical SIP DC/DC Power Modules
Compact size single inline package (SIP)
Output current 8A or 18A
Efficiencies up to 90%
Output voltage adjust
Over-current protection provides non-latching (auto-reset) operation
POLA™ compatible
Model
Input Voltage
Output Voltage
Output Current
PTV12010W
12V
1.2V to 5.5V
8A
PTV12020W
12V
1.2V to 5.5V
16A
8A & 18A PTV Series Efficiency PTV12010W Efficiency (12Vin, 3.3Vout) 100 95 90
Used for Red LEDs
Efficiency - %
85 80 75
10.8V
70
12.0V
65
13.2V
60 55 50 45 40 0
1
2
3
4
5
6
7
8
PTV12020W Efficiency (5Vout)
Iout - Amps
100 95 90
Efficiency - %
85
Used for Blue & Green LEDs
80 75
10.8V
70
12.0V
65
13.2V
60 55 50 45 40 0
2
4
6
8
10
Iout - Amps
12
14
16
18
Releases
TLC5945
80mA 12 bit PWM, 6 bit Dot Correction, w/o output delay RGB LED Video walls needing quick frame rate
UCC28060
Two-Phased Interleaved Transition Mode PFC Controller Large white LED Lights needing > 200W Frequency dithering reduces EMI
New TI Lighting website
http://www.ti.com/lighting TI LED Drivers Overview Presentation in ESP
TPS61040/1 28-V Boost Driver in SOT-23 Benefits
Features Output voltage up to 28V 400/250-mA switch current limit (TPS61040/1) High Efficiency: >85%, 28-µA no-load quiescent current typical SOT23-5 package, small inductors, low value capacitors & low overall component count Input voltage range 1.8V to 6.0V TPS61040EVM-001 TPS61040EVM-002 (White LED) TA -40 to 85°C
Ideal for LCD bias & White LED Backlight applications Extends battery life Enables ultra-small solutions Suitable for: 2- & 3-cell alkaline + 1-cell Li-Ion
Why Use Industry’s highest efficiency, lowest quiescent current in SOT-23 for ultra-small implementations
small inductor
Applications LCD Bias Supply, White-LED Supply for LCD Backlights
SOT-23
Small cap
TPS61040 28-V Boost LED Driver
White LED backlight supply PWM brightness control at EN
L1 10uH
D1
Vin 2.7V to 6.0V
D2 24V (optional) Vin
SW FB
C1 4.7uF
EN
GND
C2 1uF PWM 100Hz to 500Hz
Efficiency@Vin=3.0V and 15mA = 86%
Rs 82
White LED backlight supply analog / PWM brightness control at FB
L1 10uH
D1
D2 24V (optional)
Vin 2.7V to 6.0V
Vin
C2 100nF
SW FB
C1 4.7uF
EN
GND
R1 120k Analogue brightness control 3.3V Led Off 0V Iled =20mA Alternatively a PWM signal up to 5kHz can be used swinging from 0V to 3.3V
R2=160k
Rs 110
TPS61042 28-V Constant-Current White LED Driver Why Use
Benefits Ion
High-efficiency, small implementation
Features 1.8V to 6.0V input voltage range, output up to 28V 500-mA switch current limit Precise LED current programming with sense resistor High efficiency: >85% due to low VREF and RDSON 35-uA (typ) quiescent current, 1.0-µA shutdown Precise brightness control with PWM signal to avoid chromaticity shift 8-pin MLP package (3x3 mm2), small 100-nF output cap, small 3.3-µH inductors, low component count Disconnects LEDs during shutdown Over-voltage protection Up to 1MHz switching frequency TPS61042EVM
Suitable for: 2- & 3-cell alkaline + 1-cell LiDrives up to 6 white LEDs Accurately regulated LED current Extends battery life Easy to implement Enables ultra-small solutions
small inductor D1 MBR0530
L1 3.3uH
Co 100nF
Vcc=1.8V to 6.0V VIN
SW
CTRL
OVP
GND
Cin 4.7uF
FB
LED
Small cap
Rs
Applications
White-LED Supply for LCD Backlights: PDA, Smartphones Outdoor lighting
MLP-8 Enable / PWM brightness control 100Hz to 50kHz
EVM Rs 13
Available
TPS61058/59: White LED Flashlight Boost Converter Applications
Torch/Camera Flashlight White LED Backlight Generic Lighting Applications
Features
Input Voltage: 2.7V to 5.5V Output Voltage: 2.5V to 5.5V Output Current: -1100mA Switch Current Limit (TPS61058) - 500mA LED Current from 3.3-V Input - 1500mA Switch Current Limit (TPS61059) - 800mA LED Current From 3.3-V Input Efficiency: 80% (max) Package: 3x3 QFN-10 Fixed Frequency 650kHz (typ) Operation LED Disconnect During Shutdown Open/Shorted LED Protection Low EMI-Converter (Integrated Anti-ringing
Switch) Internal Soft-Start Over-temperature Protection Low Shutdown Current: 100nA (typ)
Benefits Minimizing external component count with total solution size of ~80mm2
TPS6106x Constant-Current white LED Driver in CSP Benefits
Features 2.7V to 6.0V input voltage range 400-mA switch current limit 1 MHz fixed frequency Integrated P-channel MOSFET rectifier 8-pin QFN package (3x3mm) or CSP Low value components, minimal count Precise LED current programming (sense resistor) Digital or PWM dimming Disconnects LEDs during shutdown Over-voltage protection: 15V on TPS61060 Short-circuit protection on ‘OUT’ 19V on TPS61061 24V on TPS61062
Suitable for: 1 cell Li-ion, 3-cell NiMH/Alkaline Drives up to 5 white LEDs Enables small inductive solution Accurately regulated LED current Flexible dimming control with integrated DAC Conserves battery power Enables use of lowest voltage output cap
Ultrasmall COut
Why Buy Small inductive-based implementation
Applications White-LED Supply for LCD Backlights: PDA, Smartphones
Digital or PWM dimming
WCSP 2x1 mm
TPS6115x Dual Output – single Inductor - LED Driver Features
Applications
Input Voltage: 3.0V to 6.0V Output Voltage: up to 27V each (max) Switch current Limit: 0.7A (max) Efficiency: 83% (max) Package: 3x3 QFN-10 2 Individual programmable, regulated current Outputs build in Power Diode & Soft-start Input to Output isolation Overvoltage & Short circuit protection Built in 1.2MHz fixed switching frequency
LED driver for up to: - 12 LED (4.0V forward voltage) - 14 LED (3.5V forward voltage)
small Inductor 4.7µH - 10µH
Benefits
Controls 2 strings with only 1 Inductor both strings can be on at the same time up to 30kHz dimming frequency
Why Buy Best in class backlight driver performance, dimming capabilities & total solutions size
small 3x3 QFN package Analog or PWM dimming
LDO LED Driver with PWM Bright Control TPS7510X Applications Keypad, Navigation and Display
V
TPS75100
Backlighting Cellular Handsets PDAs and Smartphones MP3 Players
25 mA
VDO 50 mV
∆IDX
Package
±4%
WCSP 3x3 SON
ENA
V ENB
ENB
D2A D1B D2B
ISET GND
Typical Device Specifications
Regulated Output Current With 4% LED-to-LED Matching Over Temperature Drives up to 4 LEDs at 25mA each in a Common Cathode Topology 50mV typical Dropout Voltage extends usable supply range in Li-Ion battery applications. Brightness Control Using PWM Signals Two 2-LED Banks with independent Enable and PWM brightness control per bank No Internal Switching Signals Eliminates EMI Default LED Current Eliminates External Components Default values from 3mA to 10mA (in 1 mA increments) available using innovative factory EEPROM programming Optional external resistor can be used for high-accuracy, -programmable current Over-Current and Over-Temperature Protection Available in Wafer Chip Scale Package (Sept ‘06) and 3mmx3mm SON-16 (Q4 ‘06)
TPS75100X Chip Scale
TPS7510X 3x3mm SON
ENA ENB NC VIN
GND
Features
2x2
IDX
V ENA
NC D1A D2B NC
TPS7510X
LEDs
D1A VIN
ISET D1B D2B NC
Device
BATT
NC NC GND NC
TPS60230: 3-channel, Current-regulated 125-mA WLED Charge Pump Applications
Features 2.7V to 6.5V input voltage range 3x3 mm2 QFN-16 package, only 5 components Current source for each LED, 25mA per LED High efficiency through fractional 1x & 1.5x conversion PWM dimming 1-MHz switching frequency 160-µA quiescent current
White LED backlight for color displays in Cell Phones, PDA, Media Players, Digital Cameras LED Current Adjustment EN2
EN1
Mode : VISET
LED Current
0
0
SD
0
0
1
200mV
1/3
1
0
400mV
2/3
1
1
600mV
Full
Why Buy Small, easy-to-use white LED backlight solution
High Efficiency (86%): Fractional Conversion, 1x & 1.5x
4C 1R Only
• s up to 5 wLEDs • Max 25mA per Channel • No Resistors needed
LED Current Setting 2.7V~6.5V Input Range LED Brightness control
EVM
TPS60231: 3-channel, Current-regulated 75-mA WLED Charge Pump in 3x3 QFN-16 Features 2.7V to 6.5V input voltage range 3x3 mm2 QFN-16 package, only 5 components Current source for each LED, 25mA per LED High efficiency through fractional 1x & 1.5x conversion PWM or digital dimming 1-MHz switching frequency 200-µA quiescent current TPS60231EVM-047
Applications White LED backlight for color displays in Cell Phones, PDA, Media Players, Digital Cameras LED Current Adjustment EN2
EN1
Mode : VISET
LED Current
0
0
SD
0
0
1
200mV
1/3
1
0
400mV
2/3
1
1
600mV
Full
Why Buy Small, easy-to-use white LED backlight solution 2.7V~6.5V Input Range
High Efficiency (86%): Fractional Conversion, 1x & 1.5x
4C 1R Only
• • • •
s up to 3 wLEDs TPS60230 (up to 5 LEDs) Max 25mA per Channel No Resistors needed
LED Current Setting LED Brightness control
EVM
TL4242 Constant Current LED driver Key Features
Adjustable constant current up to 500 mA (±5%) Wide input voltage range up to 42 V Open load detection Over temperature protection Short circuit proof Reverse polarity proof Wide temperature range: -40 °C to 150 °C
Benefits Supply voltage independent constant current / brightness PWM capability for dimming No external power resistor required Diagnostic capability
Applications
LED illumination and intensity control Exterior: DRLs, fog light, turn lamp, headlamp, … Interior: vanity light, map light, courtesy light, …
Battery
I
Q
PWM
TL4242 ST
GND
D
In Development
Ref
Questions
Obrigado! Para mais informações VISITE: http://www.ti.com/lighting