Mikrotik Dual Wan Load Balancing Using Pcc Method 3w3wa

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Syed Jahanzaib Personnel Blog to Share Knowledge !

July 27, 2011

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB Filed under: Mikrotik Related — Tags: dsl, dual wan load balance, load balance, mikrotik, pcc — Syed Jahanzaib / Pinochio~:) @ 10:16 AM

i 45 Votes

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB Following is a complete script for Mikrotik to combine/load balance two DSL lines. In this example I used MikrotikT RB750 5 ports router. 2 ports were connected with two difference DSL Routers, and 3rd port was connected with LAN. Both DSL are of same speed , i.e 10Mb each. DSL MODEM IP’S DSL MODEM 1 = 192.168.1.1 DSL MODEM 2 = 192.168.2.1 Also don’t forget to rename the interface names accordingly. In my personnel experience , If s request are directly hitting Mikrotik configured with PCC , then you will get good load balancing. Use src-address as classifier, this way you will get rid of problems like https/broken link, streaming issues etc. Load balancing using this PCC technique (src-address) will be effective and balanced approach when more and more connections (from clients) that occurred. I also recommend to use SQUID proxy server along with mikrotik , either parallel or in front or backend , for better response time and it will also increase good browsing experience to s. If somehow you are not satisfied with the src-address approach,play with the PCC-Classifier, then Try both addresses and ports as the classifier. While this will randomize things the most and in theory give you the most fair allocation of bandwidth, BUT there is also a good chance that it will break certain things like banking web sites and some forums. This is because often times a HTTP requests will generate several connections, so there is a chance that some requests may go out a different route than the initial one, and that will break secure web sites. For that reason I usually stick with src-address for PCC load balancing. Regard’s Syed Jahanzaib 1 2 3 4 5 6 7 8 9 10 11 12 13

/ip add add add

address address=192.168.0.1/24 network=192.168.0.0 broadcast=192.168.0.255 interface=Local address=192.168.1.2/24 network=192.168.1.0 broadcast=192.168.1.255 interface=WAN1 address=192.168.2.2/24 network=192.168.2.0 broadcast=192.168.2.255 interface=WAN2

/ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=221.132.112.8,8.8.8. /ip firewall mangle add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2

http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

1/46

8/10/2014

14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

add chain=prerouting dst-address=192.168.1.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local

add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action= add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action= add chain=prerouting connection-mark=WAN1_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN1 add chain=prerouting connection-mark=WAN2_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN2 /ip route add dst-address=0.0.0.0/0 gateway=192.168.1.1 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.1.1 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=2 check-gateway=ping /ip firewall nat add chain=srcnat out-interface=WAN1 action=masquerade add chain=srcnat out-interface=WAN2 action=masquerade

All Done ! Now Test the link by putting load, the more multiple s load you put on it, the better Load Balance result you will get

PCC WITH UN-EQUAL WAN LINKS If you have Un-Equal WAN Links, for example WAN,1 is of 4MB and WAN,2 is of 8 Mb, and you want to force MT to use WAN42link more then other because of its capacity, Then you have to Add more PCC rules asg the same two marks to a specific link i.e WAN2 , something like Code: 1 2 3

add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=m add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=m add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=m

PCC WITH HOTSPOT (Reference) 1

/ip firewall nat add action=accept chain=pre-hotspot disabled=no dst-address-type=!local hotspot=auth ٩(●̮ •)۶ ZaiB ٩(●̮ ̃ ̮ •)۶ ̃ ̮ About these ads

Comments (317)

317 Comments » 1. hi plz me….. and tell me where you live…… am Shahzad form pakistan/multan my phone number # 0092312-6460823 Comment by shahzad — July 31, 2011 @ 5:42 AM http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

2/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Reply You can me at my email address. aacable [at] hotmail.com / 0092333.xxxxxxx Comment by Pinochio / zaib — July 31, 2011 @ 6:05 AM Reply Dear, how can you make the router make load balancing on tow interfaces i will use one for my hotspote and the other for my internal LAN Comment by mtaherhassanin — December 27, 2012 @ 9:59 AM Describe in details. Comment by Syed Jahanzaib / Pinochio~:) — December 27, 2012 @ 3:06 PM I Have RB 750GL with 5 Ports i will use 3 Ports for WANs DSL Routers , the rest 2 Ports i will Use them 1 For my LAN and 1 For My HotSpot Bullet. i Used your Script from the Above as the followng /ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=41.128.225.225,41.128.225.226,163.121.128.135 /ip firewall mangle add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2 add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local——– This for my Lan add chain=prerouting dst-address=192.168.3.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local2———— this for my Hotspot add chain=prerouting dst-address=192.168.3.0/24 action=accept in-interface=Local2 add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection new-connection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection new-connection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection new-connection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local2 per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection new-connection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local2 per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection new-connection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local2 per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection new-connection-mark=WAN1_conn through=yes add chain=prerouting connection-mark=WAN1_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN1 add chain=prerouting connection-mark=WAN2_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN2 /ip route add dst-address=0.0.0.0/0 gateway=192.168.2.254 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.3.254 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.254 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.3.254 distance=2 check-gateway=ping /ip firewall nat add chain=srcnat out-interface=WAN1 action=masquerade add chain=srcnat out-interface=WAN2 action=masquerade /ip firewall nat add action=accept chain=pre-hotspot disabled=no dst-address-type=!local hotspot=auth but i belive that my hot spot Not Acting well Comment by mtaherhassanin — December 30, 2012 @ 5:20 AM Hello Dear Well i have a Question in RB 750 Mikrotik Local Interface Pluged To ISA Server Local2 Pluged To Hotspot System I am Behind the ISA Server how can i mange to make the PING to the Hotspot system succeded Local 192.168.88.0/24 Local2 192.168.80.0/24 http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

3/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Comment by mtaherhassanin — December 31, 2012 @ 10:29 AM Dear sir can it possible on 3g modem? EVO PTCL Comment by Rana Aamir — July 20, 2012 @ 9:35 PM Reply Plz help me with a scrip for a b750 3 adsl 4mb wan 192.168.2.1 dns 196.7..7.7 192.168.3.1 192.168.4.1 lan 192.168.7.1 hotspot 192.168.8.1 thanks ben Comment by Ben Heydenrych — June 29, 2013 @ 10:06 PM Reply 2. How can i achieve load balancing with these typr of setup. 2 wan and 1 hotspot LAN. normal web/light browsing traffic should be directed to WAN1 while heavy and other traffic should go to WAN 2. Comment by Collins — August 1, 2011 @ 3:26 PM Reply You have to do policy base load balancing. or you can mark packets for specific traffic and route it to your desired WAN link. Comment by Pinochio / zaib — August 4, 2011 @ 6:03 AM Reply 3. i am also enabled proxy because WAN1 is billing me based on volume of data i use. Comment by Collins — August 1, 2011 @ 4:01 PM Reply 4. hello sir i am aman can you help me how mikrotik load balasing and modem setting what is your mobile no and your E-mail Comment by Aman Manifarooqi — August 1, 2011 @ 4:05 PM Reply 5. plz sir help me Comment by Aman Manifarooqi — August 1, 2011 @ 4:06 PM Reply 6. my name is Aman farooqi plz you help me from pakistan RAWAlpindi mikrotik load balascing how make and how modem settend Comment by Aman Manifarooqi — August 1, 2011 @ 4:11 PM Reply you can me at aacable at hotmail.com Comment by Pinochio / zaib — August 4, 2011 @ 6:03 AM Reply skyp id plz 03112910453 Comment by faisal — March 30, 2014 @ 5:11 AM Reply jhanzaib sb skyp ke id ager ap deyea tu baat ho sakti hay ya cell fone mai 03112910453 Comment by faisal — March 30, 2014 @ 5:13 AM Reply aacable79 Comment by Syed Jahanzaib / Pinochio~:) — March 31, 2014 @ 3:51 PM http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

4/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

7. / ip address add address=1.1.0.5/24 network=1.1.0.0 broadcast=1.1.0.255 interface=Local comment=”” disabled=no add address=10.0.0.10/24 network=10.0.0.0 broadcast=10.0.0.255 interface=wan1 comment=”” disabled=no add address=7.7.7.10/24 network=7.7.7.0 broadcast=7.7.7.255 interface=wan2 comment=”” disabled=no / ip firewall mangle add chain=prerouting in-interface=Local connection-state=new nth=2,1 action=mark-connection new-connection-mark=conn1 through=yes comment=”” disabled=no add chain=prerouting in-interface=Local connection-mark=conn1 action=mark-routing new-routing-mark=conn1 through=no comment=”” disabled=no add chain=prerouting in-interface=Local connection-state=new nth=1,1 action=mark-connection new-connection-mark=conn2 through=yes comment=”” disabled=no add chain=prerouting in-interface=Local connection-mark=conn2 action=mark-routing new-routing-mark=conn2 through=no comment=”” disabled=no / ip firewall nat add chain=srcnat connection-mark=conn1 action=masquerade out-interface=wan1 comment=”” disabled=no add chain=srcnat connection-mark=conn2 action=masquerade out-interface=wan2 comment=”” disabled=no / ip route add dst-address=0.0.0.0/0 gateway=10.0.0.138 scope=255 target-scope=10 routing-mark=conn1 comment=”” disabled=no add dst-address=0.0.0.0/0 gateway=7.7.7.7 scope=255 target-scope=10 routing-mark=conn2 comment=”” disabled=no Comment by Aman Manifarooqi — August 4, 2011 @ 11:21 PM Reply 8. ware is this problam khaa par masllha ho sakta hai kia modem ki setting bhi karni hai aghr karni hai to kia ya is main problam, hai Comment by Aman Manifarooqi — August 4, 2011 @ 11:25 PM Reply 9. / ip address add address=1.1.0.5/24 network=1.1.0.0 broadcast=1.1.0.255 interface=Local comment=”” disabled=no add address=1.1.0.77/24 network=1.1.0.0 broadcast=1.1.0.255 interface=wan1 comment=”” disabled=no add address=5.5.5.1/24 network=5.5.5.0 broadcast=5.5.5.255 interface=wan2 comment=”” disabled=no / ip firewall mangle add chain=prerouting in-interface=Local connection-state=new nth=2,1 action=mark-connection new-connection-mark=conn1 through=yes comment=”” disabled=no add chain=prerouting in-interface=Local connection-mark=conn1 action=mark-routing new-routing-mark=conn1 through=no comment=”” disabled=no add chain=prerouting in-interface=Local connection-state=new nth=1,1 action=mark-connection new-connection-mark=conn2 through=yes comment=”” disabled=no add chain=prerouting in-interface=Local connection-mark=conn2 action=mark-routing new-routing-mark=conn2 through=no comment=”” disabled=no / ip firewall nat add chain=srcnat connection-mark=conn1 action=masquerade out-interface=wan1 comment=”” disabled=no add chain=srcnat connection-mark=conn2 action=masquerade out-interface=wan2 comment=”” disabled=no / ip route add dst-address=0.0.0.0/0 gateway=1.1.0.5 scope=255 target-scope=10 routing-mark=conn1 comment=”” disabled=no add dst-address=0.0.0.0/0 gateway=5.5.5.1 scope=255 target-scope=10 routing-mark=conn2 comment=”” disabled=no Comment by Aman Manifarooqi — August 5, 2011 @ 6:57 PM Reply First turn off dh server seetings in modem than try…good luck Comment by Faisal — August 13, 2011 @ 10:31 PM Reply 10. ab yeh sahi kar bhi liya hai tab bhi net nahi chal rahaa hai plz help me ab kia karo yeh load balasing is liye kar rha hoo is se net ki 4mb aur 4mb ke speed 8 ati hai is liye plz ab dekhye kia karoblam hai Comment by Aman Manifarooqi — August 5, 2011 @ 6:59 PM Reply This is nth base load balancing which will give you some problems in steaming , https web sites etc. but try it anyways since its the simplest way to do load balance. Make some changes to your ip scheme. Change ‘Local’ interface ip to 10.0.0.1 Change ‘WAN1′ ip to 192.168.1.1 Change ‘WAN2′ ip to 192.168.2.1 http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

5/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Change ‘WAN1′ DSL ROUTER LAN ip to 192.168.1.2 Change ‘WAN2′ DSL ROUTER LAN ip to 192.168.2.2 Now moving on to script. / ip address add address=10.0.0.1 network=10.0.0.0 broadcast=10.0.0.255 interface=Local comment=”” disabled=no add address=192.168.1.1/24 network=192.168.1.0 broadcast=192.168.1.255 interface=wan1 comment=”” disabled=no add address=192.168.2.1/24 network=192.168.2.0 broadcast=192.168.2.255 interface=wan2 comment=”” disabled=no / ip firewall mangle add chain=prerouting in-interface=Local connection-state=new nth=2,1 action=mark-connection new-connection-mark=conn1 through=yes comment=”” disabled=no add chain=prerouting in-interface=Local connection-mark=conn1 action=mark-routing new-routing-mark=conn1 through=no comment=”” disabled=no add chain=prerouting in-interface=Local connection-state=new nth=1,1 action=mark-connection new-connection-mark=conn2 through=yes comment=”” disabled=no add chain=prerouting in-interface=Local connection-mark=conn2 action=mark-routing new-routing-mark=conn2 through=no comment=”” disabled=no / ip firewall nat add chain=srcnat connection-mark=conn1 action=masquerade out-interface=wan1 comment=”” disabled=no add chain=srcnat connection-mark=conn2 action=masquerade out-interface=wan2 comment=”” disabled=no / ip route add dst-address=0.0.0.0/0 gateway=192.168.1.2 scope=255 target-scope=10 routing-mark=conn1 comment=”” disabled=no add dst-address=0.0.0.0/0 gateway=192.168.2.2 scope=255 target-scope=10 routing-mark=conn2 comment=”” disabled=no Comment by Pinochio / zaib — August 6, 2011 @ 6:32 AM Reply would you please give me Mikrotik DUAL WAN Load Balancing using PCC method in simple word i need 4WAN merging Comment by zain ul abdin — January 26, 2012 @ 4:16 PM Can you be more specific what you meant by ‘Simple Words’ The tutorial is complete reference guide. You can use it and modify it according to your need. Comment by Syed Jahanzaib / Pinochio~:) — January 27, 2012 @ 11:23 AM 11. thnaks you it is work Comment by Aman Manifarooqi — August 15, 2011 @ 11:06 PM Reply 12. plz sir help me how pcc load balasing 3.22 Comment by Aman Manifarooqi — August 15, 2011 @ 11:08 PM Reply 13. I have implemented DUAL (2) WAN Load Balancing using PCC method and it is working fine without hotspot. But I want to implement this PCC method with hotspot service. Please let me know what I should do now. Comment by Kafi — August 22, 2011 @ 11:45 AM Reply Dear Kafi, I have never tested load balancing with HOTSPOT scenario, but what I have heard or read at forums, hotspot messes with load balancing method. But give it a try and share your experience with us. Comment by Pinochio / zaib — August 22, 2011 @ 11:51 AM Reply 14. Salam bhai see pics below is this possible or not http://forum.mikrotik.com//file.php?id=7740 http://forum.mikrotik.com//file.php?id=7739 http://forum.mikrotik.com//file.php?id=7738 Comment by usmans — August 23, 2011 @ 12:49 PM Reply Yes this is very much possible achieving this kind of load balancing. Even RRD can get equal LB, but I will not recommend you to use RDD base algorithm as it have some issues with many sites n protocols. Use PCC instead. http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

6/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Just make sure that all s are hitting Mikrotik directly (where PCC is configured) The more s load you put on PCC, the better load balancing you will be able to get. Comment by Pinochio / zaib — August 24, 2011 @ 10:50 AM Reply Wow…. Amazing.. How to do this with 2 WAN only? Comment by Danish Jamil — April 3, 2012 @ 1:52 PM Reply 15. bhai mai ny 2 pc mai mikrotik install kia hai 1 mai load balancing ki hai aur dosry mai add hai aur per connetion classifier ko ma ny dst address pa set kia hai. kia yeh sahi hai yaha is sy b better ho akta hai….. dsl1 dsl2———–mikrotik pcc (dst address)——–mikrotik pppoe server——-clients dsl3 Comment by usmans — August 28, 2011 @ 1:01 AM Reply usman bhai mujay apna koi contect nuber dain plz mene loadbalsing ki kuch help lani hai app se Comment by sadaq — July 30, 2012 @ 8:38 AM Reply 16. dst-address works fine too. All depend on your usage scenario. You can configure pcc and pppoe on the same server. in this way you can use src-address as your classifier. Comment by Pinochio / zaib — August 28, 2011 @ 10:54 AM Reply 17. bhai agar mai pcc aur pppoe same sever mai configure karta ho to jab mai us mai thunder cache ka mangle rule add karta ho to wo work nai karta…is liy mai 2 server use kar raha ho…. Comment by usmans — August 28, 2011 @ 2:07 PM Reply 18. Great to use PCC to load balance, but I don’t know I’m using nth is better at my network… Comment by another mikrotik tips — September 24, 2011 @ 9:30 AM Reply PCC is a very customizable and enhanced version of Load balancing as compared to NTH . Using PCC you can get rid of many problems found in NTH, for example, broken http/https link, streaming issues and some others. (Using pcc with src-address as classifier.) Anyhow if NTH is fulfilling your requirements and you are satisfied with the results, you can stick with it as loon as it doesn’t bother you Comment by Pinochio~:) — September 24, 2011 @ 10:30 AM Reply 19. im having one wan link- 4 Mb ,another one is 2Mb, is it is possible to loadbalance with pcc Comment by tamilmaran — October 28, 2011 @ 8:31 AM Reply yes you can, Just give create more pcc rule to give priority to 4mb rule, so 2mb will be used twice as compare to 2 mb, to get some balanced load balancing. Comment by Pinochio~:) — October 28, 2011 @ 12:33 PM Reply can u pls , edit n give me the script, im poor in scripting… Comment by tamilmaran — June 26, 2012 @ 12:02 AM 20. Hi, I also have rb750. Now I want to do load balancing on 2 dsl lines. How will I know that port 1 is Local, port 2 is WAN1 ans so on? Also for WAN1 dsl is the ip address 192.168.1.1? And for WAN2 dsl is the ip address 192.168.2.1? Comment by Nouman Aziz — November 12, 2011 @ 4:59 PM Reply http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

7/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

You can check port status by various ways. Following command will blink the port light. /interface ethernet blink ether1 OR /interface ethernet monitor ether1 /interface ethernet monitor ether2 /interface ethernet monitor ether3 Comment by Pinochio~:) — November 14, 2011 @ 10:38 AM Reply Sir I want to access winbox from wan port….please advice ,,,,,i have public static ip at my adsl router .i have add port forwading in router …port is 8291 : what i do at my 750GL router ….microtik router wan ip is 192.168.0.100 …and adsl router lan ip is 192.168.0.1…please advice …\ Regards Comment by faisalmirzapk — April 10, 2013 @ 7:18 PM 21. dear sir, i want to implement fcc method with pppoe server in 1mikrotik OS x86 pc….. how to do that? kindly help me ASAP……;) Comment by fareed — November 16, 2011 @ 9:14 AM Reply PCC with PPPoE Server on single Mikrotik Server. Read the following link http://aacable.wordpress.com/2011/08/29/mikrotik-4-wan-load-balancing-using-pcc-with-pppoe-server-complete-script/ Comment by Pinochio~:) — November 16, 2011 @ 10:33 AM Reply 22. i have 2 Satellite internet connections and i want to do loadbalancing and i have 2 diffrent public ips. Comment by fareed — November 16, 2011 @ 9:17 AM Reply 23. Thankx For Help …………………… Comment by Mazhar Sheikh — November 16, 2011 @ 3:28 PM Reply 24. 3 wan load balancing, no need to set static IP to the interfaces; multiple ADSL services and the Mikrotik PCC rules along with some inbound mangling to allow a single router to load balance traffic across as many non bonded links as required. credits to: http://www.mikrotik-routeros.com/?p=12 Note that none of this config requires the use of IP addresses at all, as it simply uses the pppoe-client interfaces and your lan interface to mark traffic. In my example wan1-pppoe,wan2-pppoe,wan3-pppoe are used and lan /ip route add check-gateway=arp comment=”WAN 3 – Distance 1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan3-pppoe routing-mark=wan3 add check-gateway=arp comment=”WAN 2 – Distance 1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan2-pppoe routing-mark=wan2 add check-gateway=arp comment=”WAN 1 – Distance 1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan1-pppoe routing-mark=wan1 add check-gateway=arp comment=”WAN 1 – Distance 2″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan2-pppoe routing-mark=wan1 add check-gateway=arp comment=”WAN 2 – Distance 2″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan3-pppoe routing-mark=wan2 add check-gateway=arp comment=”WAN 3 – Distance 2″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan1-pppoe routing-mark=wan3 add check-gateway=arp comment=”WAN 1 – Distance 3″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan3-pppoe routing-mark=wan1 add check-gateway=arp comment=”WAN 2 – Distance 3″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan1-pppoe routing-mark=wan2 add check-gateway=arp comment=”WAN 3 – Distance 3″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan2-pppoe routing-mark=wan3 add check-gateway=arp comment=”Default Route – Distance 1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan1-pppoe add check-gateway=arp comment=”Default Route – Distance 2″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan3-pppoe add check-gateway=arp comment=”Default Route – Distance 3″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan2-pppoe add check-gateway=arp comment=”Static Route – WAN1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan1-pppoe routing-mark=static-wan1 add check-gateway=arp comment=”Static Route – WAN2″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan2-pppoe routing-mark=static-wan2 add check-gateway=arp comment=”Static Route – WAN3″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan3-pppoe routing-mark=static-wan3

/ip firewall mangle http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

8/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

/ip firewall mangle add action=mark-connection chain=input comment=”Mark new inbound connection wan1″ connection-state=new disabled=no in-interface=wan1-pppoe new-connection-mark=wan1 \ through=yes add action=mark-connection chain=input comment=”Mark new inbound connection wan2″ connection-state=new disabled=no in-interface=wan2-pppoe new-connection-mark=wan2 \ through=yes add action=mark-connection chain=input comment=”Mark new inbound connection wan3″ connection-state=new disabled=no in-interface=wan3-pppoe new-connection-mark=wan3 \ through=yes add action=mark-connection chain=prerouting comment=”Mark established inbound connection wan1″ connection-state=established disabled=no ininterface=wan1-pppoe \ new-connection-mark=wan1 through=yes add action=mark-connection chain=prerouting comment=”Mark established inbound connection wan2″ connection-state=established disabled=no ininterface=wan2-pppoe \ new-connection-mark=wan2 through=yes add action=mark-connection chain=prerouting comment=”Mark established inbound connection wan3″ connection-state=established disabled=no ininterface=wan3-pppoe \ new-connection-mark=wan3 through=yes add action=mark-connection chain=prerouting comment=”Mark related inbound connection wan1″ connection-state=related disabled=no ininterface=wan1-pppoe \ new-connection-mark=wan1 through=yes add action=mark-connection chain=prerouting comment=”Mark related inbound connection wan2″ connection-state=related disabled=no ininterface=wan2-pppoe \ new-connection-mark=wan2 through=yes add action=mark-connection chain=prerouting comment=”Mark related inbound connection wan3″ connection-state=related disabled=no ininterface=wan3-pppoe \ new-connection-mark=wan3 through=yes add action=mark-routing chain=output comment=”Mark new inbound route wan1″ connection-mark=wan1 disabled=no new-routing-mark=static-wan1 through=no add action=mark-routing chain=output comment=”Mark new inbound route wan2″ connection-mark=wan2 disabled=no new-routing-mark=static-wan2 through=no add action=mark-routing chain=output comment=”Mark new inbound route wan3″ connection-mark=wan3 disabled=no new-routing-mark=static-wan3 through=no add action=mark-connection chain=prerouting comment=”Mark traffic that isn’t local with PCC mark rand (3 possibilities) – option 1″ connectionstate=new disabled=no \ dst-address-type=!local in-interface=lan new-connection-mark=wan1_pcc_conn through=yes per-connection-classifier=both-addresses:3/0 add action=mark-connection chain=prerouting comment=”Mark traffic that isn’t local with PCC mark rand (3 possibilities) – option 2″ connectionstate=new disabled=no \ dst-address-type=!local in-interface=lan new-connection-mark=wan2_pcc_conn through=yes per-connection-classifier=both-addresses:3/1 add action=mark-connection chain=prerouting comment=”Mark traffic that isn’t local with PCC mark rand (3 possibilities) – option 3″ connectionstate=new disabled=no \ dst-address-type=!local in-interface=lan new-connection-mark=wan3_pcc_conn through=yes per-connection-classifier=both-addresses:3/2 add action=mark-connection chain=prerouting comment=”Mark established traffic that isn’t local with PCC mark rand (3 possibilities) – option 1″ connection-state=\ established disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan1_pcc_conn through=yes per-connection-classifier=\ both-addresses:3/0 add action=mark-connection chain=prerouting comment=”Mark established traffic that isn’t local with PCC mark rand (3 possibilities) – option 2″ connection-state=\ established disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan2_pcc_conn through=yes per-connection-classifier=\ both-addresses:3/1 add action=mark-connection chain=prerouting comment=”Mark established traffic that isn’t local with PCC mark rand (3 possibilities) – option 3″ connection-state=\ established disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan3_pcc_conn through=yes per-connection-classifier=\ both-addresses:3/2 add action=mark-connection chain=prerouting comment=”Mark related traffic that isn’t local with PCC mark rand (3 possibilities) – option 1″ connectionstate=related \ disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan1_pcc_conn through=yes per-connection-classifier=bothaddresses:3/0 add action=mark-connection chain=prerouting comment=”Mark related traffic that isn’t local with PCC mark rand (3 possibilities) – option 2″ connectionstate=related \ disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan2_pcc_conn through=yes per-connection-classifier=bothaddresses:3/1 add action=mark-connection chain=prerouting comment=”Mark related traffic that isn’t local with PCC mark rand (3 possibilities) – option 3″ connectionstate=related \ disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan3_pcc_conn through=yes per-connection-classifier=bothaddresses:3/2 add action=mark-routing chain=prerouting comment=”Mark routing for PCC mark – option 1″ connection-mark=wan1_pcc_conn disabled=no newrouting-mark=wan1 through=\ yes add action=mark-routing chain=prerouting comment=”Mark routing for PCC mark – option 2″ connection-mark=wan2_pcc_conn disabled=no newrouting-mark=wan2 through=\ yes http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

9/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

add action=mark-routing chain=prerouting comment=”Mark routing for PCC mark – option 3″ connection-mark=wan3_pcc_conn disabled=no newrouting-mark=wan3 through=\ yes Comment by adrian — November 26, 2011 @ 7:25 AM Reply Hi, what about NAT rules ? (script in IP-Firewall-NAT) Comment by esalehnet — November 29, 2012 @ 1:30 AM Reply 25. is is working OK to me, after I modified a bit to use only 2 wans on my router Comment by adrian — November 26, 2011 @ 7:29 AM Reply 26. Jahanzaib Bhai I need your help Would you……………. Comment by Umair Hanif — December 4, 2011 @ 8:28 PM Reply Regarding ??? Comment by Pinochio~:) — December 7, 2011 @ 10:42 AM Reply i have mikrotik 3.22 and i want to use 2 WAN link load balancing Comment by umair — December 13, 2011 @ 11:03 PM You need at least ver 3.30 for pcc base load balancing. Comment by Pinochio~:) — December 14, 2011 @ 10:42 AM 27. I have upgraded to version 3.30 Comment by umair — December 14, 2011 @ 11:46 PM Reply 28. These are great scripts, but could you possibly explain how to change the gateway check to check a remote IP address rather than the gateway IP address (for instances where the DSL line may be down, but the modem still up) – im sure its not as easy as just changing the ip address in the check? Comment by David — December 22, 2011 @ 4:26 PM Reply You are right, its not that easy to integrate netwatch with the PCC. I stopped working on this script long time ago. I will do some r&d on it and will update the article accordingly. Comment by Pinochio~:) — December 23, 2011 @ 10:59 AM Reply Salam Dear Sir , Sir ap kasy hai .umied hai k ap thek hai .ALLAH ap per desta shufqat rakha.Sir main UBNT wireless setup laga raha hun.Aur sir mujha ap say kuch help ke zaroorat hai .wo ya k main us k liya mikrotik ka kon sa ver use karun uar mikrotik ruterbord kon sa purchas karun.qk es ma humara dedicated links be hai .aur SIR humara owner ya chata hai k ptcl jasie wireless modem ma setting ho. SIR Cache server be creat karna hai kindly ap us ka be bta dijya ga. Sir main umied karta hun k ap jaldi aur bhater jawab send kary gia. Waqas sabir from Faisalabad. E-mail = [email protected] Mob= 03157215729 Comment by Muhammad Waqas Sabir — August 30, 2012 @ 10:54 PM Reply 29. Hi, Sir I have done dual wan load balancing on MK RB750 v 5.9. I have two 4 mbps connection. The problem I am facing is the second dsl line is not much is use. Sometimes I get 7-8 mB speed but sometimes it drops out so I just left with the 4MB. Any thoughts or suggestions? Thanks. Comment by Nouman Aziz — December 23, 2011 @ 1:05 AM Reply If ‘sometimes’ you able to get 7-8 mbps , then your PCC is configure okay. http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

10/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

If ‘sometimes’ you able to get 7-8 mbps , then your PCC is configure okay. what classifier are you using? Comment by Pinochio~:) — December 23, 2011 @ 10:57 AM Reply 30. I am using Dst.Address for both lines. Comment by Nouman Aziz — December 25, 2011 @ 12:10 AM Reply It will happen if you use dst-address, for example if there are 10 online s and 8 of them are using you tube.com, then PCC will bind you-tube at first dsl link, and other web at other link. You have to read a lot on PCC classifier, goto wiki and read thoroughly then play with this option. Comment by Pinochio~:) — December 25, 2011 @ 9:44 AM Reply 31. So which classifier should I use? Comment by Nouman Aziz — December 25, 2011 @ 10:09 AM Reply 32. Can you please explain me which classifier do I change and how? Thanks. Comment by Nouman Aziz — December 25, 2011 @ 12:43 PM Reply Dear Noman, I guess its time for you to do some research and read teh mikrotik wiki on How PCC works. Please start with this one and you will get idea on which classifier is best for you. http://wiki.mikrotik.com/wiki/How_PCC_works_(beginner) After all its your network and you have to decide what classifer to use depends on your network usage. Please Read, Read and Read. Comment by Pinochio~:) — December 25, 2011 @ 10:17 PM Reply 33. ok Thanks/. Comment by Nouman — December 26, 2011 @ 1:04 AM Reply 34. sir muhe yee bataye ke x86 main bhi pcc load balasing ho sakti hai Comment by noman — December 31, 2011 @ 7:20 PM Reply It doesn’t matter what architecture you use , you can do it on x86 or any RB. Just make sure you use ver 3.30 or above. preferably latest 5.x series. Comment by Pinochio~:) — December 31, 2011 @ 9:17 PM Reply min ne computer par install kia hai mikrotik ko pcc load balasing chaliy gi Comment by noman — December 31, 2011 @ 9:23 PM yes if u configure it properly. Comment by Syed Jahanzaib / Pinochio~:) — January 2, 2012 @ 9:59 AM 35. Sir, This load balancing works great when we put a load on it (browse heavy site, or watch youtube). Is there any way to keep both WAN’s alive and working equally. For example even when we browse lite sites it should use both lines 50/50. Thanks Comment by nominet — January 4, 2012 @ 3:45 PM Reply Try using different classifier. There are 8 various, test which one works for you best http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

11/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Comment by Syed Jahanzaib / Pinochio~:) — January 4, 2012 @ 4:03 PM Reply 36. I have tried them and I liked ‘scr-address’ and ‘both-addresses and ports’ one. Comment by Nouman — January 5, 2012 @ 12:26 AM Reply 37. Sir what is failover? Comment by Ayoob — January 6, 2012 @ 1:30 AM Reply ‘Failover’ It will always check the modem status before sending any packets, If the modem is not reachable it will not send the packets. Comment by Syed Jahanzaib / Pinochio~:) — January 6, 2012 @ 10:55 AM Reply 38. I want to add another WAN3 with the ip 192.168.3.1 Can you please write a script for me thanks. Comment by Asad — January 6, 2012 @ 11:27 AM Reply /ip route add check-gateway=arp comment=”WAN 3 – Distance 1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan3-pppoe routing-mark=wan3 add check-gateway=arp comment=”WAN 2 – Distance 1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan2-pppoe routing-mark=wan2 add check-gateway=arp comment=”WAN 1 – Distance 1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan1-pppoe routing-mark=wan1 add check-gateway=arp comment=”WAN 1 – Distance 2″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan2-pppoe routing-mark=wan1 add check-gateway=arp comment=”WAN 2 – Distance 2″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan3-pppoe routing-mark=wan2 add check-gateway=arp comment=”WAN 3 – Distance 2″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan1-pppoe routing-mark=wan3 add check-gateway=arp comment=”WAN 1 – Distance 3″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan3-pppoe routing-mark=wan1 add check-gateway=arp comment=”WAN 2 – Distance 3″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan1-pppoe routing-mark=wan2 add check-gateway=arp comment=”WAN 3 – Distance 3″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan2-pppoe routing-mark=wan3 add check-gateway=arp comment=”Default Route – Distance 1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan1-pppoe add check-gateway=arp comment=”Default Route – Distance 2″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan3-pppoe add check-gateway=arp comment=”Default Route – Distance 3″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan2-pppoe add check-gateway=arp comment=”Static Route – WAN1″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=wan1-pppoe routing-mark=staticwan1 add check-gateway=arp comment=”Static Route – WAN2″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=wan2-pppoe routing-mark=staticwan2 add check-gateway=arp comment=”Static Route – WAN3″ disabled=no distance=3 dst-address=0.0.0.0/0 gateway=wan3-pppoe routing-mark=staticwan3 /ip firewall mangle add action=mark-connection chain=input comment=”Mark new inbound connection wan1″ connection-state=new disabled=no in-interface=wan1pppoe new-connection-mark=wan1 \ through=yes add action=mark-connection chain=input comment=”Mark new inbound connection wan2″ connection-state=new disabled=no in-interface=wan2pppoe new-connection-mark=wan2 \ through=yes add action=mark-connection chain=input comment=”Mark new inbound connection wan3″ connection-state=new disabled=no in-interface=wan3pppoe new-connection-mark=wan3 \ through=yes add action=mark-connection chain=prerouting comment=”Mark established inbound connection wan1″ connection-state=established disabled=no ininterface=wan1-pppoe \ new-connection-mark=wan1 through=yes add action=mark-connection chain=prerouting comment=”Mark established inbound connection wan2″ connection-state=established disabled=no ininterface=wan2-pppoe \ new-connection-mark=wan2 through=yes add action=mark-connection chain=prerouting comment=”Mark established inbound connection wan3″ connection-state=established disabled=no ininterface=wan3-pppoe \ new-connection-mark=wan3 through=yes add action=mark-connection chain=prerouting comment=”Mark related inbound connection wan1″ connection-state=related disabled=no ininterface=wan1-pppoe \ new-connection-mark=wan1 through=yes add action=mark-connection chain=prerouting comment=”Mark related inbound connection wan2″ connection-state=related disabled=no ininterface=wan2-pppoe \ new-connection-mark=wan2 through=yes add action=mark-connection chain=prerouting comment=”Mark related inbound connection wan3″ connection-state=related disabled=no ininterface=wan3-pppoe \ new-connection-mark=wan3 through=yes add action=mark-routing chain=output comment=”Mark new inbound route wan1″ connection-mark=wan1 disabled=no new-routing-mark=staticwan1 through=no add action=mark-routing chain=output comment=”Mark new inbound route wan2″ connection-mark=wan2 disabled=no new-routing-mark=statichttp://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

12/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

wan2 through=no add action=mark-routing chain=output comment=”Mark new inbound route wan3″ connection-mark=wan3 disabled=no new-routing-mark=staticwan3 through=no add action=mark-connection chain=prerouting comment=”Mark traffic that isn’t local with PCC mark rand (3 possibilities) – option 1″ connectionstate=new disabled=no \ dst-address-type=!local in-interface=lan new-connection-mark=wan1_pcc_conn through=yes per-connection-classifier=both-addresses:3/0 add action=mark-connection chain=prerouting comment=”Mark traffic that isn’t local with PCC mark rand (3 possibilities) – option 2″ connectionstate=new disabled=no \ dst-address-type=!local in-interface=lan new-connection-mark=wan2_pcc_conn through=yes per-connection-classifier=both-addresses:3/1 add action=mark-connection chain=prerouting comment=”Mark traffic that isn’t local with PCC mark rand (3 possibilities) – option 3″ connectionstate=new disabled=no \ dst-address-type=!local in-interface=lan new-connection-mark=wan3_pcc_conn through=yes per-connection-classifier=both-addresses:3/2 add action=mark-connection chain=prerouting comment=”Mark established traffic that isn’t local with PCC mark rand (3 possibilities) – option 1″ connection-state=\ established disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan1_pcc_conn through=yes per-connection-classifier=\ both-addresses:3/0 add action=mark-connection chain=prerouting comment=”Mark established traffic that isn’t local with PCC mark rand (3 possibilities) – option 2″ connection-state=\ established disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan2_pcc_conn through=yes per-connection-classifier=\ both-addresses:3/1 add action=mark-connection chain=prerouting comment=”Mark established traffic that isn’t local with PCC mark rand (3 possibilities) – option 3″ connection-state=\ established disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan3_pcc_conn through=yes per-connection-classifier=\ both-addresses:3/2 add action=mark-connection chain=prerouting comment=”Mark related traffic that isn’t local with PCC mark rand (3 possibilities) – option 1″ connection-state=related \ disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan1_pcc_conn through=yes per-connection-classifier=bothaddresses:3/0 add action=mark-connection chain=prerouting comment=”Mark related traffic that isn’t local with PCC mark rand (3 possibilities) – option 2″ connection-state=related \ disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan2_pcc_conn through=yes per-connection-classifier=bothaddresses:3/1 add action=mark-connection chain=prerouting comment=”Mark related traffic that isn’t local with PCC mark rand (3 possibilities) – option 3″ connection-state=related \ disabled=no dst-address-type=!local in-interface=lan new-connection-mark=wan3_pcc_conn through=yes per-connection-classifier=bothaddresses:3/2 add action=mark-routing chain=prerouting comment=”Mark routing for PCC mark – option 1″ connection-mark=wan1_pcc_conn disabled=no newrouting-mark=wan1 through=\ yes add action=mark-routing chain=prerouting comment=”Mark routing for PCC mark – option 2″ connection-mark=wan2_pcc_conn disabled=no newrouting-mark=wan2 through=\ yes add action=mark-routing chain=prerouting comment=”Mark routing for PCC mark – option 3″ connection-mark=wan3_pcc_conn disabled=no newrouting-mark=wan3 through=\ yes after that all you need to do is make your 3 pppoe client conections coresponding to your wans, pppoe client cone3ctions with and provided from yout ISP, and in NAT…make a masquerade in ip firewall nat… click + to add net nat rule, Chain – scrnat….than go to Action tab and select masquerade… that is all this config is the config that I am using on a rb750, for 3 wans Comment by Acidu — January 6, 2012 @ 6:40 PM Reply 39. Hi Sir, What is the function of distance in routes? Comment by Asad — January 6, 2012 @ 8:34 PM Reply 40. Hi, thanks for the great howto. I have a setup with 2 WANs and when I vpn to the router I can no longer ping or connect to the local addresses. Local interface is: 192.168.0.0/24 VPN local address is: 10.0.1.100 VPN remote address is: 10.0.2.100 Before setting up the load balancing I was able to connect to 192.168.0.102 or 192.168.0.101. Comment by quinametin — January 18, 2012 @ 10:05 AM Reply Just create an address list (vpn subnet included) and on the mangle rules exclude them , e.g src-address-list=!pptps and dst-addresslist=!pptps For more info, read comments in following article, few guiys made it worked with pcc. http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

13/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

http://aacable.wordpress.com/2011/06/04/mikrotik-4-wan-load-balance-pcc-complete-script-by-zaib/ Comment by Syed Jahanzaib / Pinochio~:) — January 18, 2012 @ 10:38 AM Reply Ok, found it

I had to add to firewall -> nat a masquerade with the source 10.0.2.0/24

Comment by quinametin — January 18, 2012 @ 11:14 AM Reply gr8. Comment by Syed Jahanzaib / Pinochio~:) — January 18, 2012 @ 11:18 AM 41. Which classifier should I use? I want 4 + 4 = 8. So traffic should spread aross them two links. Thanks. Comment by Bablu — January 18, 2012 @ 1:54 PM Reply Use ‘both addressess and ports’ approach. Comment by Syed Jahanzaib / Pinochio~:) — January 18, 2012 @ 5:37 PM Reply 42. Jitna b Geo Khushi se Geo. Ye Bablu ki dua ha Jahanzaib Bhai. Comment by Bablu — January 19, 2012 @ 3:29 PM Reply Comment by Syed Jahanzaib / Pinochio~:) — January 20, 2012 @ 10:46 AM Reply 43. Hello, Thank you for helpful posts, I little bit confused with IP addresses and how to setup load balance with my RB750G. I have 2 ADSL from same ISP with 2 linksys modems with static external IP and 10M speed each.I cannot access the modems they r locked by ISP. I just getting internal IP by DH in range 192.168.1.1/254. On both modems are same gateway address 192.168.1.1 and same IP range. How can I configure load balancing???? Please help!!!! Need ASAP!!! Thank you in advance!!! Nikos Comment by Nikos — January 25, 2012 @ 2:11 AM Reply Move them on different subnet. For example ISP DSL Modems: DSL1 = 192.168.1.1 DSL2 = 192.168.2.1 Mikrotik: WAN1 = 192.168.1.2 / GW > 192.168.1.1 WAN2 = 192.168.2.2 / GW > 192.168.2.1 This way things will get simpler and manageable for you. You can use static ip on you mikrotik wan interface of same subnet series provided by the modem. Comment by Syed Jahanzaib / Pinochio~:) — January 25, 2012 @ 10:56 AM Reply Thank you for fast response, The problem is that I cannot change DSL2 to 192.168.2.1 its locked by ISP and both DSL modems had same 192.168.1.1. In my scenario it will be something like this : DSL1:192.168.1.1==>WAN1=192.168.1.2 DSL2:192.168.1.1==>WAN2=192.168.1.3 This will work or NOT??? Please advice !!! Thank you in advance Nikos http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

14/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Comment by Nikos — January 25, 2012 @ 7:12 PM I have not tested such scenario, in my opinion it should not work. Comment by Syed Jahanzaib / Pinochio~:) — January 26, 2012 @ 10:55 AM !Try defining the outbound interface. For example replace this. /ip route add dst-address=0.0.0.0/0 gateway=1.2.3.4 routing-mark=to_wan-ISP1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=1.2.3.4 routing-mark=to_wan-ISP2 check-gateway=ping With following /ip route add dst-address=0.0.0.0/0 gateway=1.2.3.4%eth1-ISP routing-mark=to_wan-ISP1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=1.2.3.4%eth2-ISP routing-mark=to_wan-ISP2 check-gateway=ping Replace the eth1-ISP with your own wan itnerface name , use the notation % for sure. If it works , let me know Regard’s Comment by Syed Jahanzaib / Pinochio~:) — October 21, 2013 @ 11:59 AM Reply 44. Alsalamu Alaykom Dear Brother can you please send me a Backup file for RB 750 Load Balance ? Comment by Moataz Ibrahem — January 30, 2012 @ 11:02 PM Reply http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/ Comment by Syed Jahanzaib / Pinochio~:) — January 30, 2012 @ 11:08 PM Reply 45. sir main ne pcc load balasing ki hai load balasing to sahi hai par dh par webproxy nahi chal rahey plz help me Comment by mani — January 31, 2012 @ 12:05 AM Reply If you 4.x that’s relatively easy to do because it has a feature that can match connections that do not yet have a connection mark. I will not recommend you to use mikrotik webproxy with pcc on same box, It is recommended to use external proxy like SQUID or ISA. new version and it will be easy for you to use mikrotik web proxy. /ip firewall mangle add chain=output connection-mark=no-mark action=mark-connection new-connection-mark=Internet1_conn through=yes per-connectionclassifier=both-addresses:2/0 add chain=output connection-mark=no-mark action=mark-connection new-connection-mark=Internet2_conn through=yes per-connectionclassifier=both-addresses:2/1 On 3.x the rule set would be quite much more complicated to make sure you don’t interfere with potentially existing connection marks that must not be changed, so hopefully you can 4.x Comment by Syed Jahanzaib / Pinochio~:) — January 31, 2012 @ 2:31 PM Reply 46. sir this script not work as failover it works only when modem turned off in the case when modem power is on but the modem is disconnect failover not work 100% sure sir i want a solution for failover free or paid not matter but perfect solution my id is [email protected] I m use 3.22 v http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

15/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Thank You Comment by WASEEM AHMED — February 1, 2012 @ 5:12 AM Reply 48. hi i have 16 mb pipe connected with 4 wan tplink load balancer , and load balancer connect with mikro tik OS installed on pc i configured dns, firewall, web proxy correctly but my browsing speed is too slow. is in mikrotik there is place to mention wan link rate, means does mikro tik required the link rate in Wan link. if yes then plzz tell me becoz i m watching all time my wan link in interface option it never rich to 16 mb infect it is not crossing 4 mb in all time pick time non pick time …guide me as soon as possible………… thxzzzzzzzzzzzzz Comment by rehmat ali gulwating — February 7, 2012 @ 3:50 AM Reply Slow browsing , hmmm… there can be multiple issue, I told you earlier, make sure all of your client is using your mikrotik as there primary DNS server, secondly, using IDM , try to 10-15 multiple files (Big s) and see if you can able to from all links. Comment by Syed Jahanzaib / Pinochio~:) — February 7, 2012 @ 9:34 AM Reply 49. DEAR……. YES I CAN USE 16 MB PIPE WITH IDM BUT 1 TROUBLE I FIND THAT WHEN I PING TO TPLINK IP 192.168.205.1 REPLY IN 1 OR 2 MS CONTINUE SLY BUT WHEN I PING PTCL MODEM LAN IP (192.168.201.1 MODEM 1,192.168.202.1 MODEM 2, 192.168.203.1 MODEM 3,192.168.204.1 MODEM 4) SOME TIME PING REPLY IN 6 TO 7 MS AND SOME TIMES REQUEST TIME OUT OCCURS I CHANGE LAN CARDS OF MIKROTIK BUT NOTHING HAPPENED AND WHEN I CONNECT TPLINK LOADBALANCER DIRECT 2 WINDOWS PC PING REPLIES IN 1 MS AND ALL WORKED FINE…. THEN Y PING IS BREAKING WITH MIKROTIK PLEASE GUIDE ME AND SHOOT THIS TROUBLE WITH UR GOOD EXPERIENCE THANKING YOU, Comment by rehmat ali gulwating — February 10, 2012 @ 3:15 AM Reply You probably have a bad network design topology. Also check with your queueing section, Try to disable all Queues, and thenc heck the ping reply. If ping works fine after disabling the Queue, try the following. http://aacable.wordpress.com/2011/12/07/mikrotik-howto-give-ping-icmp-high-priority/ Comment by Syed Jahanzaib / Pinochio~:) — February 10, 2012 @ 8:58 AM Reply 50. my name habib Comment by a — February 10, 2012 @ 9:27 PM Reply 51. are you on line in wordpress Comment by a — February 10, 2012 @ 9:28 PM Reply 52. Hi, Work fine, but “both-addresses-and-ports” per connection classifier creates problems (eg ftp client: ive ports are open on another WAN, so the ftp server considers it as a security violation). I recommend an “both addresses” pcc configuration to avoid this. Best regards Comment by Alexandre Alouit — February 13, 2012 @ 10:33 PM Reply Yes you are right, both address provides more reliable connections. But for some operators who demands more bandwidth rather then reliability, both-addresses-and-ports gives overall better load balancing, but they face broken link issues. Comment by Syed Jahanzaib / Pinochio~:) — February 14, 2012 @ 8:48 AM Reply 53. Salam, this is rehmat, i trace problem in my network it is from client side. i means my clients have a lots of viruses, Trojans and spammers and their pcs use t and udp ports to access wan.ports are 445,80,23 which i trace out i have problem with port 80 becoz its a browsing port (http) please send me rules or any script to block viruses,Trojans and spammers completely. or any other guide to resolve this issue. thxxxxxxxxxxx Comment by rehmat ali gulwating — February 14, 2012 @ 2:51 AM Reply Monitor your network closely using monitoring tools like TORCH (built-in mikrotik tool) and block all suspected ports.) http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

16/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Few examples are here. http://aacable.wordpress.com/2011/08/15/mikrotik-howto-prevent-mt-host-from-invalid--attempts-from-lanwan-s/ Comment by Syed Jahanzaib / Pinochio~:) — February 14, 2012 @ 8:51 AM Reply 54. Hi. Salam jahanzaib bhai. jahanzaib bhai i have 4 mb connection of PTCL. and main mikrotik 3.30 pay hotspot server use kr raha hun. i have 30 clients on it . 300 gb limit ki waja say now i want to add one more 4 mb connection. Plz guide me k main kesay on ki load balancing krun. is wqt meray WAN ka address 192.168.1.150 and LAN ka address 192.168.0.150 hai. yaa to ap yay guide kr dain k dono 4 mb ka 50/50 use ho ya phr ya bta dain k main half clients WAN1 pay kesay krun and half WAN2 pay ? because main ing limit ko cross nhi krna chahta. its too expensive for me if ing limit crossed. Comment by SHAFQAT FARHAN — February 22, 2012 @ 10:45 AM Reply 55. and dono connections ptcl say liyay hain main nay so . dono ka ip address same hai yani k DSL1 192.168.1.1 and DSL2 192.168.1.1 and i dont have authority to change this address. Comment by SHAFQAT FARHAN — February 22, 2012 @ 10:51 AM Reply First thing first. Both links must be on different subnet, otherwise you won’t be able to do proper load balance. One workaround is to put another router (any cheap brand like tplink etc) in between mikrotik WAN2 and DSL2 and give it another subnet ip. For example like this. DSL1 ======> === >> MIKROTIK ROUTER ETH1 192.168.1.1 192.168.1.2 DSL2 ======> TPLINK ROUTER === >> MIKROTIK ROUTER ETH2 192.168.1.1 192.168.5.1 192.168.5.2 Also check this It might help you. http://aacable.wordpress.com/2011/10/27/mikrotik-policy-routing-based-on-client-ip-address/ Comment by Syed Jahanzaib / Pinochio~:) — February 23, 2012 @ 9:16 AM Reply 56. thank you so much sir. now i will change the ip address of one of the DSL router. now plz tell me how could i do load balancing on hotspot server. and i want k dono DSL’s equally use hun. i mean agar total ing (from clients) 200 GB howi hai to DSL1 say 100 GB and DSL2 say 100 GB ho. i mean i want the average from both of the DSL. Comment by SHAFQAT FARHAN — February 23, 2012 @ 11:51 AM Reply To use PCC with HOTSPOT , use the following. http://aacable.wordpress.com/2012/02/12/mikrotik-pcc-with-hotspot/ You can’t define on that how much exact amount of data should be used from each wan link. Comment by Syed Jahanzaib / Pinochio~:) — February 23, 2012 @ 11:59 AM Reply 57. to phr kya is trah ho skta hai k main half clients WAN1 pay kr dun and half WAN2 pay. ?? Comment by SHAFQAT FARHAN — February 23, 2012 @ 12:06 PM Reply Yes you can, see the link i have sent earlier. policy/ip base client routing Comment by Syed Jahanzaib / Pinochio~:) — February 23, 2012 @ 1:37 PM Reply jahanzaib bhai os policy main 2 LAN output hain. jab k meray situation kuch yun hai k meray pas bulletm2 hai. main wireless k through clients ko net provide kr raha hun. so agar main 2 output krta hun to bullet main to aik he input jaey gi. Comment by SHAFQAT FARHAN — February 23, 2012 @ 8:26 PM You can use single output (LAN) also. The example showed in the article was not using 2 output, Both s are on same LAN. Comment by Syed Jahanzaib / Pinochio~:) — February 24, 2012 @ 9:28 AM 58. sir, give me a script of queue tree bandwith setting mikrotik rb750G please….. note: I use dual wan about it wan Comment by aanet — February 24, 2012 @ 7:22 AM http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

17/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Reply 59. dear sir Syed Jahanzaib sir main ne TWO wan ore ONE lan ka mikrotik server banya hai jis ka scrpit ye hai. (( /ip address add address=192.168.5.1/24 network=192.168.5.0 broadcast=192.168.5.255 interface=LAN add address=192.168.0.2/24 network=192.168.0.0 broadcast=192.168.0.255 interface=WAN1 add address=192.168.2.2/24 network=192.168.2.0 broadcast=192.168.2.255 interface=WAN2 /ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=208.67.220.220,208.67.222.222 /ip firewall mangle add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2 add chain=prerouting dst-address=192.168.0.0/24 action=accept in-interface=LAN add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=LAN add chain=prerouting dst-address-type=!LAN in-interface=LAN per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!LAN in-interface=LAN per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting connection-mark=WAN1_conn in-interface=LAN action=mark-routing new-routing-mark=to_WAN1 add chain=prerouting connection-mark=WAN2_conn in-interface=LAN action=mark-routing new-routing-mark=to_WAN2 /ip route add dst-address=0.0.0.0/0 gateway=192.168.0.1 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.0.1 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=2 check-gateway=ping /ip firewall nat add chain=srcnat out-interface=WAN1 action=masquerade add chain=srcnat out-interface=WAN2 action=masquerade sir jab main internet use karta hun tu mera server srif os wan ka interinet use karta hai jis ki speed kam hoti hai jab k meri dosri wan per speed kafi achi hoti hai ek wan meri 3mbps ki hai ore dosri 4 mbps ki hai kindly tell me a script jis se main in dono wan ko use kar sekon yan phier asa ho in dono wan main se jis ki speed zaida ho server os wan ko use karey kindly send me a script jis se mera masla hal ho jaye Comment by ali — February 24, 2012 @ 9:50 PM Reply Your script seems fine. Try playing with the distance value. Comment by Syed Jahanzaib / Pinochio~:) — February 25, 2012 @ 12:51 PM Reply yes i have licnes call me 03245001960 pta Comment by noman — March 1, 2012 @ 11:01 AM Reply 60. jahanzaib bhai do u have some info that how can i get license of ISP from PTCL or PTA . and how much cost it have ?? Comment by SHAFQAT FARHAN — February 25, 2012 @ 9:54 PM http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

18/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Reply 61. hi.. i’m using this script right now and i want to port forward (23156) from WAN1 to internet.. can u help me sir Comment by nick — March 5, 2012 @ 8:58 PM Reply 62. sir meine aap ka dual wan configuration wala script use kia hai leikin mere aik wan se reply nahin aaraha Comment by Yasir — March 9, 2012 @ 9:04 PM Reply What is the impact you are getting because of this? Check the DISTANCE VALUE. Comment by Syed Jahanzaib / Pinochio~:) — March 12, 2012 @ 9:04 AM Reply 63. mein mikrotik ka os ver 3.3 use kerraha hoon Comment by Yasir — March 9, 2012 @ 9:09 PM Reply 64. hello ! the difference with this scenario is that i have modem 1 IP : 79.106.15.44 ( bridge with PPPoE connection with name and ) or it doesn’t influence in the configuration modem 2 IP : 79.106.15.45 ( bridge with PPPoE connection with name and ) with gateway 79.106.14.1 or dynamic LAN : 192.168.2.1/24 can you please help me with the configuration regards Comment by sidio — March 12, 2012 @ 3:52 AM Reply 65. salaam sir how are u main pppoe server use kar rahaa hooo aap mjhe yeh batao ke dil up par kon se colore use hote hai main ne net ki waire se bjiliy gozarni hai plz tell me Comment by musa — March 19, 2012 @ 9:57 AM Reply 66. hi, this is Rehmat ali have to ask one thing is that i follow script given by u on this page ( http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-loadbalancing-using-pcc-method-complete-script-by-zaib/ ) . problem is only 1 wan is using internet named wan1 but 2nd wan named wan4 is not using similarly means with pcc method i m able to use both links in same time……? if yes then please solve this issue because it can’t use both links in same time. Wan1 route is shows as AS and in black color but Wan4 route is shows as S and in blue color. i think problem is with ip route. reply me as soon as possible. thanking you, Comment by Rehmat Ali Gulwating — March 20, 2012 @ 3:34 PM Reply 67. Very Very Thanks Mr,Zaib With this script you changed my life Comment by Haroon nimroozy — March 29, 2012 @ 11:17 AM Reply 68. Dear Bro, I m using MIKROTIK from last 2 years with these settings. I have 4 WANS and 1 LAN. 1 wan 4Mbs, 2nd 4Mb, 3rd 6Mb and 4th is 2Mb. i splice the ip with differnet subnets and send traffic through routes. 1 group ips gets 4 2nd group ip also 4 3rd group 6 mb and 4th group 2mb. and all s or on PPPOE. But now i want to combine all traffic and then send it to 1 LAN. means 4 lans = 1 lan ,4+4+6+2=16 Mb. I many Mikrotik persons for this issue but all in vain. I am using RB750G 3.22v. Need help.. Comment by Junaid — April 1, 2012 @ 11:02 PM Reply A quick search on google can save you from posting queries http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

19/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

http://aacable.wordpress.com/2011/06/04/mikrotik-4-wan-load-balance-pcc-complete-script-by-zaib/ Comment by Syed Jahanzaib / Pinochio~:) — April 2, 2012 @ 8:33 AM Reply Thanks a lot Brother…..i’ll work on it then i’ll let u know if i faced any error.. Comment by Junaid — April 4, 2012 @ 1:04 PM 69. Jahanzaib Bhai, i it Possible to have Load Balancer and Hotspot on same Machine? Comment by Danish Jamil — April 4, 2012 @ 11:42 PM Reply Yes its possible. http://aacable.wordpress.com/2012/02/12/mikrotik-pcc-with-hotspot/ Comment by Syed Jahanzaib / Pinochio~:) — April 5, 2012 @ 8:53 AM Reply 70. Dear Syed, How can we use the web proxy with your configuration (not on a box of course..)? Comment by Alex Alouit (@alexalouit) — April 8, 2012 @ 7:49 PM Reply You mean like the one showed here ??? http://aacable.wordpress.com/2011/12/29/howto-to-enable-mikrotik-routeros-web-proxy-in-transparent-mode/ Comment by Syed Jahanzaib / Pinochio~:) — April 9, 2012 @ 8:34 AM Reply Yes, unfortunately, for me it does not work. The proxy works fine from outside (lan network), but the internal drift does not work. My current config is: nat 0 chain=srcnat action=masquerade src-address=192.168.2.0/24 out-interface=wan1 1 chain=srcnat action=masquerade src-address=192.168.2.0/24 out-interface=wan2 2 chain=dstnat action=redirect to-ports=3128 protocol=t src-address=192.168.2.0/24 dst-port=80 mangle 0 chain=input action=mark-connection new-connection-mark=WAN1_conn through=yes in-interface=wan1 1 chain=input action=mark-connection new-connection-mark=WAN2_conn through=yes in-interface=wan2 2 chain=output action=mark-routing new-routing-mark=to_WAN1 through=yes connection-mark=WAN1_conn 3 chain=output action=mark-routing new-routing-mark=to_WAN2 through=yes connection-mark=WAN2_conn 4 chain=prerouting action=accept dst-address=X.X.X.X/24 in-interface=lan 5 chain=prerouting action=accept dst-address=X.X.X.X/24 in-interface=lan 6 ;;; 80 chain=prerouting action=mark-connection new-connection-mark=WAN1_conn through=yes protocol=t dst-address-type=!local ininterface=lan dst-port=80 per-connection-classifier=both-addresses-and-ports:2/0 7 chain=prerouting action=mark-connection new-connection-mark=WAN1_conn through=yes dst-address-type=!local in-interface=lan perconnection-classifier=both-addresses:2/0 8 ;;; 80 chain=prerouting action=mark-connection new-connection-mark=WAN2_conn through=yes dst-address-type=!local in-interface=lan perconnection-classifier=both-addresses-and-ports:2/1 9 chain=prerouting action=mark-connection new-connection-mark=WAN2_conn through=yes dst-address-type=!local in-interface=lan perconnection-classifier=both-addresses:2/1 10 chain=prerouting action=mark-routing new-routing-mark=to_WAN1 through=yes in-interface=lan connection-mark=WAN1_conn 11 chain=prerouting action=mark-routing new-routing-mark=to_WAN2 through=yes in-interface=lan connection-mark=WAN2_conn proxy enabled: yes src-address: 0.0.0.0 port: 3128 parent-proxy: 0.0.0.0 parent-proxy-port: 0 cache-: max-cache-size: none cache-on-disk: yes max-client-connections: 600 max-server-connections: 600 max-fresh-time: 3d http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

20/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

serialize-connections: no always-from-cache: no cache-hit-ds: 4 cache-drive: primary-slave The router runs on Router OS 5.14 Do you see that does not work? Regards Comment by Alex Alouit (@alexalouit) — April 9, 2012 @ 8:25 PM Error in copy/paste, my mangle config number 8 is: chain=prerouting action=mark-connection new-connection-mark=WAN2_conn through=yes protocol=t dst-address-type=!local ininterface=lan dst-port=80 per-connection-classifier=both-addresses-and-ports:2/1 but it does affect my web proxy problem. The problem I encounter is also valid to intercept DNS requests (cache dns transparent). The firewall is it not challenged? Comment by Alex Alouit (@alexalouit) — April 10, 2012 @ 10:04 PM use notepad +…paste there… and then copy from there and paste in new terminal… Comment by Acidu — April 11, 2012 @ 1:08 AM For the copy/paste error, I spoke about the comment, not the CLI configuration of the router.. Regards Comment by Alex Alouit (@alexalouit) — April 11, 2012 @ 5:43 PM 71. Dear Sir I want to know these configuration also use with 750up router board ? I want load balancing with 2 wan on 750up router board …please help …. I also want load balancing using hotspot …… Regards Comment by faisalmirzapk — April 8, 2012 @ 8:15 PM Reply The script posted in this article will work on any version of routerboard. to use it with hotspot you should follow this. http://aacable.wordpress.com/2012/02/12/mikrotik-pcc-with-hotspot/ Comment by Syed Jahanzaib / Pinochio~:) — April 9, 2012 @ 8:33 AM Reply 72. Dear Sir plz help me mere RB750GL hai mey us pe 3 wan chalana chata ho with bondig (means merge all bandwidth ?) mere ye configuration hai. 4Mb = 1st DSL router address = 192.168.0.1 => ehter1 WAN 4Mb = 2nd DSL router address = 192.168.2.1 => ehter2 WAN 6Mb = 3rd DSL router address = 192.168.3.1 => ehter3 WAN Bandwidth merge = 4Mb + 4Mb + 6Mb = 14Mbps local network = 192.168.1.1 => ehter5 DH server on local network => ehter5 Bandwidth controlling in Kbps on specific IP (local address) or kia interface ka name bhi change karna parey ga wo kese hoga ??? n plz help me step by step mey ne apki batae hui script mey changes ki hai wo nichy hai is mey koi mistake hai ? or baqi complete script send karden Thanks ———————————————————————————————————————————————————————————————————— rename the interface ????? ———————————————————————————————————————————————————————————————————— /ip address 02 add address=192.168.1.1/24 network=192.168.1.0 broadcast=192.168.1.255 interface=Local http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

21/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

03 add address=192.168.0.2/24 network=192.168.0.0 broadcast=192.168.0.255 interface=WAN1 04 add address=192.168.2.2/24 network=192.168.2.0 broadcast=192.168.2.255 interface=WAN2 05 add address=192.168.3.2/24 network=192.168.3.0 broadcast=192.168.3.255 interface=WAN3 06 /ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=221.132.112.8,8.8.8.8 07 08 /ip firewall mangle 09 add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn 10 add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn 11 add chain=input in-interface=WAN3 action=mark-connection new-connection-mark=WAN3_conn 12 add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 13 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2 14 add chain=output connection-mark=WAN3_conn action=mark-routing new-routing-mark=to_WAN3 15 add chain=prerouting dst-address=192.168.0.0/24 action=accept in-interface=Local 16 add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.3.0/24 action=accept in-interface=Local 17 18 add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes 19 add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection newconnection-mark=WAN3_conn through=yes 20 21 add chain=prerouting connection-mark=WAN1_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN1 22 add chain=prerouting connection-mark=WAN2_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN2 23 add chain=prerouting connection-mark=WAN3_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN3 24 /ip route 25 add dst-address=0.0.0.0/0 gateway=192.168.0.1 routing-mark=to_WAN1 check-gateway=ping 26 add dst-address=0.0.0.0/0 gateway=192.168.2.1 routing-mark=to_WAN2 check-gateway=ping 27 add dst-address=0.0.0.0/0 gateway=192.168.3.1 routing-mark=to_WAN3 check-gateway=ping 28 add dst-address=0.0.0.0/0 gateway=192.168.0.1 distance=1 check-gateway=ping 29 add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=2 check-gateway=ping 30 add dst-address=0.0.0.0/0 gateway=192.168.3.1 distance=3 check-gateway=ping 31 /ip firewall nat 32 add chain=srcnat out-interface=WAN1 action=masquerade 33 add chain=srcnat out-interface=WAN2 action=masquerade 34 add chain=srcnat out-interface=WAN3 action=masquerade ———————————————————————————————————————————————————————————————————— DH SERVER also ———————————————————————————————————————————————————————————————————— Bandwith controlling ??????? THANKS Regards Ehtisham Ul Haq Comment by Ehtisham Ul Haq — April 11, 2012 @ 12:18 PM Reply change the lines from 18 add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection new-connection-mark=WAN1_conn through=yes 19 add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection new-connection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection newconnection-mark=WAN3_conn through=yes TO below lines http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

22/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

TO below lines add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:3/0 action=mark-connection new-connection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:3/1 action=mark-connection new-connection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:3/2 action=mark-connection new-connection-mark=WAN3_conn through=yes Comment by Syed Jahanzaib / Pinochio~:) — April 11, 2012 @ 1:14 PM Reply thanks Sir plz send me also interface rename script and DH server Comment by Ehtisham Ul Haq — April 11, 2012 @ 1:47 PM Dear Sir this script is working in my case ?? ip dh-server> setup Select interface to run DH server on dh server interface: local Select network for DH addresses dh address space: 192.168.1.0/24 Select gateway for given network gateway for dh network: 192.168.1.1 Select pool of ip addresses given out by DH server addresses to give out: 192.168.1.25-192.168.1.254 Select DNS servers dns servers: 192.168.1.1 Select lease time lease time: 3d Comment by Ehtisham Ul Haq — April 11, 2012 @ 2:11 PM 73. Dear Bro. how can we use Manager and manage s and their ing on v3.3 with level4 license. if their some solution please tell me how can i do it. Comment by Junaid — April 11, 2012 @ 4:49 PM Reply 74. Hi, I have an address-list and want to force that all addresses in address-list ISP1 always goes to to WAN1, what should I do? Comment by Ari — April 26, 2012 @ 11:55 PM Reply Read This. http://aacable.wordpress.com/2011/10/27/mikrotik-policy-routing-based-on-client-ip-address/ Comment by Syed Jahanzaib / Pinochio~:) — April 27, 2012 @ 9:14 AM Reply 75. Hello, have you ever noticed redirect problem with NAT? I have the latest version of RouterOS on ESXi 5. I Can’t use the redirect (eg web proxy transparent, or transparent DNS cache). Comment by Alex Alouit (@alexalouit) — April 27, 2012 @ 3:59 PM Reply Here is my configuration: /ip firewall filter add action=drop chain=input disabled=no dst-port=3128 in-interface=wan1 protocol=t add action=drop chain=input disabled=no dst-port=3128 in-interface=wan2 protocol=t /ip firewall mangle add action=mark-connection chain=input disabled=no in-interface=wan1 new-connection-mark=WAN1_conn through=yes add action=mark-connection chain=input disabled=no in-interface=wan2 new-connection-mark=WAN2_conn through=yes add action=mark-routing chain=output connection-mark=WAN1_conn disabled=no new-routing-mark=to_WAN1 through=yes add action=mark-routing chain=output connection-mark=WAN2_conn disabled=no new-routing-mark=to_WAN2 through=yes add action=accept chain=prerouting disabled=no dst-address=0.0.0.0/24 in-interface=lan http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

23/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

add action=accept chain=prerouting disabled=no dst-address=0.0.0.0/24 in-interface=lan add action=mark-connection chain=prerouting disabled=no dst-address-type=!local in-interface=lan new-connection-mark=WAN1_conn through=yes per-connection-classifier=both-addresses:2/0 add action=mark-connection chain=prerouting disabled=no dst-address-type=!local in-interface=lan new-connection-mark=WAN2_conn through=yes per-connection-classifier=both-addresses:2/1 add action=mark-routing chain=prerouting connection-mark=WAN1_conn disabled=no in-interface=lan new-routing-mark=to_WAN1 through=yes add action=mark-routing chain=prerouting connection-mark=WAN2_conn disabled=no in-interface=lan new-routing-mark=to_WAN2 through=yes /ip firewall nat add action=masquerade chain=srcnat disabled=no out-interface=wan1 src-address=0.0.0.0/24 add action=masquerade chain=srcnat disabled=no out-interface=wan2 src-address=0.0.0.0/24 add action=redirect chain=dstnat comment=”Transparent Web Cache” disabled=yes dst-port=80 protocol=t to-ports=3128 /ip proxy set always-from-cache=no cache-= cache-hit-ds=4 cache-on-disk=yes enabled=yes max-cache-size=unlimited max-clientconnections=600 max-fresh-time=3d max-server-connections=600 \ parent-proxy=0.0.0.0 parent-proxy-port=0 port=3128 serialize-connections=no src-address=0.0.0.0 /ip route add disabled=no distance=1 dst-address=0.0.0.0/0 gateway=0.0.0.0 routing-mark=to_WAN1 scope=30 target-scope=10 add disabled=no distance=1 dst-address=0.0.0.0/0 gateway=0.0.0.0 routing-mark=to_WAN2 scope=30 target-scope=10 add disabled=no distance=1 dst-address=0.0.0.0/0 gateway=0.0.0.0 scope=30 target-scope=10 add disabled=no distance=2 dst-address=0.0.0.0/0 gateway=0.0.0.0 scope=30 target-scope=10 Comment by Alex Alouit (@alexalouit) — April 27, 2012 @ 4:11 PM Reply I never used Mikrotik’s Web Proxy service with PCC. Only heard that it do make some problems if you have all setup on single box i.e PCC / Firewall / WEBPROXY. Its better to use external proxy for cache. Comment by Syed Jahanzaib / Pinochio~:) — April 28, 2012 @ 4:21 PM Reply 76. Hello Could you help me please. I am using 2 wan load balancing with PCC rules. But I want to use WAN1 generally and WAN2 if WAN1 is full. How can I do it. Also I use load balancing PCC with hotspot but there are problems when browsing https sites. Thanks a lot Best Regards Eynulla Samadov Comment by Eynulla Samadov — May 7, 2012 @ 7:11 PM Reply You can’t shift to wan2 if wan1 is FULL using mikrotik AFAIK. Try using Load Balancing scenario. or policy base routing. E.g: http://aacable.wordpress.com/2011/10/27/mikrotik-policy-routing-based-on-client-ip-address/ Comment by Syed Jahanzaib / Pinochio~:) — May 8, 2012 @ 3:16 PM Reply 77. Best tutorial, works from first attempt. Thank you for that. I have a small problem and wish that you can help me with. My board is RB493G (9 ports), I am using 2 ports for load sharing. Other ports for local net. The problem is that I fail to communicate with other ports now (I cannot access the shares nor ping my hosts ). I wish that you could help me solving this problem. Comment by Taha — May 12, 2012 @ 3:40 AM Reply Are you using HOTSPOT ? Comment by Syed Jahanzaib / Pinochio~:) — May 14, 2012 @ 8:57 AM Reply 78. Thank you problem is solved no need to worry about it. What should be done is just create a prerouting chain with accept to each network segment. in /ip firewall mangle http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

24/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Comment by Taha — May 12, 2012 @ 7:17 PM Reply 79. Yes I am using hotspot . All I did to solve the problem is to create a mangle rule with accept from each segment to the other one. I have one problem left which is not related to the script of yours but being an expert in Mikrotik I would like to get your opinion on it. My RB is 493G (V5.16) with no wireless cards installed, instead I have an AP connected to one of the ETH2. I have 2 iPhones jail broken, connected to the same AP acting as the wireless HS I cannot see the shares between them. I have installed Multicast package still not working. If I connect the Iphones to an AP before the RB everything works fine. I would appreciate sharing your experience on solving this problem. Comment by Taha — May 14, 2012 @ 1:48 PM Reply turn off Universal NAT to enable s communicate with each other. because hotspot poison the network to forece every device to use HS as there default gateway. http://aacable.wordpress.com/2011/09/12/mikrotik-hotspot-quick-setup-guide-cli-version/ Comment by Syed Jahanzaib / Pinochio~:) — May 14, 2012 @ 2:13 PM Reply 80. 1 /ip hotspot set address-pool=none——————————- could not do.. what are you referring to ? 2 OR 3 /ip hotspot set numbers=hotspot1 address-pool=none————– done—————– 4 OR 5 /ip firewall nat add chain=pre-hotspot dst-address-type=!local hotspot=auth action=accept—————— was already there——————And problem is still there Comment by Taha — May 14, 2012 @ 2:47 PM Reply 81. hum apne server ki secript kaise jan sakte hain k hum ne us ko kia kia script di hai Comment by obaid — May 22, 2012 @ 8:49 PM Reply You can use Export command to get all mikrotik configuration in human readable format which will show you every bit of your router config. Comment by Syed Jahanzaib / Pinochio~:) — May 25, 2012 @ 8:53 AM Reply 82. sir i use your this script my mikrotik 3.30 L6 but just i wan line work not both at a time what happen? one time just 1 WAN work if i unplug 192.168.1.1 WAN1 then WAN2 work if i unplug wan2 then wan1 work but not both , if 2 wan are connectd wit then just WAN1 worked ? pleas help me what hapen? Comment by obaid — May 23, 2012 @ 10:50 AM Reply Reset to default. then re.configure. Comment by Syed Jahanzaib / Pinochio~:) — May 25, 2012 @ 8:52 AM Reply 83. Hello……i have a blue router address in Route List……..and one wan is working each time i disable the other not both at a time….any ideas??!! Comment by Leado — June 4, 2012 @ 10:08 PM Reply 84. Hi. I do have two dsl routers in bridge mode (different isps) and i need to have the pppoe (client) in my mikrotik 750. i need to have all the available bandwidth in one PC (192.168.200.50). what is the best script to use? router 1 is 10/1 Mbps with IP 192.168.2.1/24 router 2 is 4/1Mbps with IP 192.168.10.254/24 lan is 192.168.200.0/24 some help plz! Comment by vortex — June 14, 2012 @ 9:56 PM Reply any ideas? Comment by vortex — June 15, 2012 @ 9:24 PM Reply http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

25/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

85. Hello Sir, Thank you for this great tutorial. it worked for me in first attempt. I have one question though. I use accelerator and when I youtube videos with the accelerator it spreads the load on the 2 wan interfaces that I have which is perfect. but when I watch youtube videos it only uses one of my wans. I tried to change the classifier to both-addresses-and-ports but still when watching youtube videos it only uses one. I am now using both-ports which works great for me in accelerator, utorrent, and browsing. but still no luck when watching youtube videos. any advice. Your brother from Iraq Badr Comment by Badr — June 15, 2012 @ 4:26 PM Reply PCC don’t merge WAN Links, it only load balance request accross multiple connection. The more link you put on it, the better results you will get. Comment by Syed Jahanzaib / Pinochio~:) — June 16, 2012 @ 10:11 AM Reply how will i be able to merge wan links? Comment by vortex — June 16, 2012 @ 11:24 AM 86. Hello Sayed Jahanzaib. Thank you for your quick reply. Do you have any tutorial on how to merge wan links or just something to start with? Thanks Comment by Badr — June 16, 2012 @ 3:07 PM Reply 87. Hi, zaiB I am Ali Muhamad from indonesia, could you help me please. I want to disable using Software manager eg: IDM or Toorent. My conection only 2 Mbps and will be use 20 pc client. If you can help me here is my email: oceaniatravel [AT ] DOT com Comment by Ali Muhamad — June 18, 2012 @ 7:52 AM Reply Actually it is difficult to block torrent. The best way is to limit there whole bandwidth or impose bandwidth quota. OR you can mark packets for mp3 exe iso etc and restrict them using queue. OR another approach is to use Radisu and select quota plenty, for example if a reaches 1 Gb quota for the day, his bandwidth drops half e.g from 512k to 256k. Comment by Syed Jahanzaib / Pinochio~:) — June 18, 2012 @ 8:45 AM Reply 88. i have WAN1=2mbps ip=192.168.1.64 gateway= 192.168.1.254 /WAN2=5mbps ip=192.168.2.100 gateway 192.168.2.1 IS THIS CORRECT??? /ip address add address=192.168.0.1/24 network=192.168.0.0 broadcast=192.168.0.255 interface=Local add address=192.168.1.64/24 network=192.168.1.0 broadcast=192.168.1.255 interface=WAN1 add address=192.168.2.100/24 network=192.168.2.0 broadcast=192.168.2.255 interface=WAN2 /ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=8.8.4.4,8.8.8.8 /ip firewall mangle add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2 add chain=prerouting dst-address=192.168.1.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection newconnection-mark=WAN2_conn through=yes http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

26/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

add chain=prerouting connection-mark=WAN1_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN1 add chain=prerouting connection-mark=WAN2_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN2 /ip route add dst-address=0.0.0.0/0 gateway=192.168.1.254 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.1.254 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=2 check-gateway=ping /ip firewall nat add chain=srcnat out-interface=WAN1 action=masquerade add chain=srcnat out-interface=WAN2 action=masquerade Comment by Eduardo — June 21, 2012 @ 1:55 AM Reply Looks fine to me, test it. Comment by Syed Jahanzaib / Pinochio~:) — June 21, 2012 @ 10:52 AM Reply 89. rb450g is enough for this operation with 50 hotspot clients? Comment by zeeshan — June 21, 2012 @ 6:01 PM Reply yes Comment by Syed Jahanzaib / Pinochio~:) — June 22, 2012 @ 8:50 AM Reply 90. As-Salam-Alaikum h r u .. dear..??? i m new to use mikrotik server.. i don’t know abt it … i need ur help .. how to edit script .. and how to add .. 4mb and 1 mb lines in load balancing.. i have requested to upgrade my 1mb link to 4mb and hopefully it will be withing a couple of days… sir plx tell me how to edit hai configure script Regards Kashif Ali Comment by Kashif Ali — June 21, 2012 @ 6:37 PM Reply The script provided in this article is complete script to load balance 2 wan links. copy paste them in notepad and edit it as per your network / mikrotik configuration. You have to first learn basics of mikrotik. Goto forum / wiki / google , there are very good guides available there. Comment by Syed Jahanzaib / Pinochio~:) — June 22, 2012 @ 8:56 AM Reply 91. Hello……i have a blue router address in Route List……..and one wan is working each time i disable the other not both at a time….any ideas??!! Comment by Leado — June 22, 2012 @ 7:37 PM Reply 92. Could u please tell me how to add Script (notepad) file in Mikrotik??? i don’t know about script editing.. please make a script for me .. one for load balancing and other for hotspot server. i have two 4mb DSL link of ptcl.. Comment by Kashif Ali — June 23, 2012 @ 8:25 PM Reply 93. Hello Mr Syed I’m using load balancin with NTH method because it collect the line , for ex. WAN1 (4M) + WAN2 (4M) = (8M) got transfer rat with IDM 1000 KB/S did PCC method do that ??? and can you help me how can i make port forward with NTH Comment by Ahmed Morgan — July 13, 2012 @ 8:29 PM Reply Many thanks I tried and i worked fine with (ADSL 2m + ADSL 2m + ADSL 4m) = ADSL 8M Comment by Ahmed Morgan — July 30, 2012 @ 10:04 PM Reply Great http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

27/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Comment by Syed Jahanzaib / Pinochio~:) — August 3, 2012 @ 7:51 AM 94. Hello, this one doesn’t work for me: PCC WITH UN-EQUAL WAN LINKS add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection newconnection-mark=WAN2_conn through=yes there is no traffic on this one… Can I use 3/0 for 1st, 3/1 for 2nd and 3/2 for wan1 again? I use per-connection-classifier=src-address. Best regards, Petar Comment by Petar — July 30, 2012 @ 1:02 AM Reply 95. Hello being unable to access my in order to create a new post I would like to ask the question here: Is there a way to access the Mikrotik file system ? I have an RB450G and would like to delte some files at NAND level say : voltage.ko file. Thank you indvane for yrour help. Taha Comment by Taha — August 2, 2012 @ 7:38 AM Reply Yes if your RB have serial connection, you can access it. Read following articles http://manio.skyboo.net/mikrotik/ (Below one is for x86 versions) http://aacable.wordpress.com/2012/01/14/howto-recover-mikrotik---forgotten-/ Comment by Syed Jahanzaib / Pinochio~:) — August 3, 2012 @ 7:28 AM Reply hi I am using routerboard 750 for load balancing 2 4mb lines.Everything is good except secure sites or websites which does not allow ip change.FTP through firezilla also not working properly. I dont know how to use src-address as pcc classifier. Will it do the work. Can you guide me to proper tutorial? I have read your tutorial http://aacable.wordpress.com/2012/04/14/howto-exempt-any--website-from-mikrotik-pcc/ but can it be done for ssl sites. Comment by usman — January 11, 2013 @ 5:08 PM Just replace both-addresses-and-ports with src-address Comment by Syed Jahanzaib / Pinochio~:) — January 12, 2013 @ 10:15 AM 96. i’ve tried the load balancing, internet and load balancing running well but i still can’t ping my router public address i monitor the traffic using torch, and i see RX traffic but no TX, seems the traffic can’t get back to the incoming ISP (traffic is receive but can’t reply) Comment by athan — August 30, 2012 @ 11:55 AM Reply 97. Salam Dear Sir , Sir ap kasy hai .umied hai k ap thek hai .ALLAH ap per desta shufqat rakha.Sir main UBNT wireless setup laga raha hun.Aur sir mujha ap say kuch help ke zaroorat hai .wo ya k main us k liya mikrotik ka kon sa ver use karun uar mikrotik ruterbord kon sa purchas karun.qk es ma humara dedicated links be hai .aur SIR humara owner ya chata hai k ptcl jasie wireless modem ma setting ho. SIR Cache server be creat karna hai kindly ap us ka be bta dijya ga. Sir main umied karta hun k ap jaldi aur bhater jawab send kary gia. Waqas sabir from Faisalabad. E-mail = [email protected] Mob= 03157215729 Comment by Muhammad Waqas Sabir Comment by Muhammad Waqas Sabir — September 2, 2012 @ 1:57 PM Reply

Hardware requirements are based on number of clients that will be accessing the network resources. http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

28/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Hardware requirements are based on number of clients that will be accessing the network resources. For smaller network, RB450, RB450G would be enough. For cache Server, if you have some know-how on Linux environment, then I will recommend you to go with SQUID proxy. Search my blog or Google, and you will find many helpful resources regarding configuring mikrotik/squid. Comment by Syed Jahanzaib / Pinochio~:) — September 3, 2012 @ 8:44 AM Reply a.a brother ma nay 4 wireless spot bany hn aur mikro tik dh use kar raha hn but jab ma hotspot use karta hn to mary 3 spot k andar any waly thk say hoty han par 1 spot asa ha jahan par hoty hi ho jata ha agur ip binding bi karon tab bi un s k page ata ha problum ya ha k serprofile kam nahi karti but isi spot par default profile ko karon to thk kam karti ha but sab s ko defalt profile to nahi day sakta kindly ap is ka hal jaldi batin phaly bi ap ko comment kya tha ap shyad hamary comments ko nahi dakhty kindly is bar ko positiv e din cell no 0312-5741540 Comment by basaam — September 12, 2012 @ 10:25 PM Reply without knowing technical specs, I cant comment. Post your config here. or email me. You can copy default profile and rename it as per requirements then make necessary changes. Comment by Syed Jahanzaib / Pinochio~:) — September 16, 2012 @ 12:58 PM 98. how does when i used internet soucer with DCHP?how? Comment by budi — September 18, 2012 @ 8:32 AM Reply 99. Asalam o Alikum sir mane 5 WAN ka load balancing banna ha kya ap mujhe source bana k mail kar sakty hain mera nam Zohaib Bin Khalid ha mane ek server banwaya tha jis na bana k diya tha os na nai btaya or na hi mujhe back up diya mera server dead para howa ha plzzzz help kar dain mane 10 connection liya hain ptcl sa or sub k sub 10MB hain,,,,,,,,,, [email protected] Zohaib Bin Khalid Pakistan Lahore Comment by Zohaib Bin Khalid — October 2, 2012 @ 7:37 PM Reply 100. I have used your PCC script , all is working fine with the PPPOE but when using hotspot its only sending traffic through 1 gateway . does not balance the traffic like in PPPOE Comment by Ferdi de Beer — October 5, 2012 @ 7:09 PM Reply to test i open 2x CMD in windows. then i use tracert to google and facebook . In PPPOE it shows that one 192.168.4.1 and other 192.168.2.1 but in Hotspot only *.*.4.1 Comment by Ferdi de Beer — October 5, 2012 @ 7:12 PM Reply 101. how to change the per connection classifier if we have a dual wan with the first port off 93Mbps and the second 11Mbps with the same gateway what’s the best solution to solve this . Comment by Agashi — October 6, 2012 @ 7:25 PM Reply 102. Hello, I setuped my L/B as exactly the way you showed us but i’m having Stream Issues, If I listen to youtube it always cut(stop) I have 10mb on wan1 and 6mb on wan2.. Do you have any clue? Comment by dbRenaud — October 7, 2012 @ 8:49 AM Reply Try changing the classifier to src-addres Comment by Syed Jahanzaib / Pinochio~:) — October 7, 2012 @ 2:33 PM Reply http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

29/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Thanks bro….but in that way i am not getting the merged speeds….Load is only on WAN1 Comment by usman — January 12, 2013 @ 9:56 PM 103. Hello i have NanoStation M5 /RB SXT+ RB750 G. i connected both NM5 & SXT to two isp (pppoe). so i run dh server in this device. in 750g i used dh client to have internet. but when i use 2 dh client i cannot use both of them at the same time. and only one of them useing. how i can have both rb+nm5 internet in same time on 750g? i used this way:http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/ Comment by Karim — October 7, 2012 @ 8:07 PM Reply 104. Syed , could u tell me is there a way to this scenario : WAN1 >>>> Mikrotik —–> s with subnet 10.0.1.1/24 get internet from wan1 and s from subnet 10.0.2.1/24 gets internet from wan2 on same interface WAN2 >>>> is this possible in anyway to do it…. Comment by agashi — October 9, 2012 @ 1:40 AM Reply This will surely help you in getting some ideas . . . http://aacable.wordpress.com/2011/10/27/mikrotik-policy-routing-based-on-client-ip-address/ Comment by Syed Jahanzaib / Pinochio~:) — October 9, 2012 @ 4:28 PM Reply 105. on everyway i doo , i get a issue with reaching radius vica versa . because when i route the second trafic to another gw then i do a tracert on it i get this : http://postimage.org/image/xyo4aitef/ i’ve tried on routing it , adding a vpn to the main mikrotik but always i can’t reach radius … please can u help me on solving this . Comment by agashi — October 11, 2012 @ 2:18 PM Reply 106. sir i have a mikritik load balncind pcc mathod used, but is not working . sir 1 line is working butt 2 line is not working. i have used the mikrotik 3.30 . please solve my problem,sir i cal adeel ahmad but is not halpe me. Comment by naveed — October 31, 2012 @ 1:25 PM Reply 107. your script works like a charm. but when use external proxy (squid) with pcc load balancing, it’s not working since pcc seems to maintain all connection state between source and destination (both address & port). if i disable all pcc mangle rules, external proxy is wortking, http packets is redirected to squid, but it use only 1 gateway. is there any way to use external squid proxy with pcc load balancing ? Comment by lostbytes — November 10, 2012 @ 9:31 AM Reply I haven’t tried this scenario. Usually I use separate RB for LB. This way things dont get complicated when it comes to troubleshoot any problem. Comment by Syed Jahanzaib / Pinochio~:) — November 12, 2012 @ 10:26 AM Reply ahh…i see. that’s an option too, use 1st RB to do LB, then 2nd RB for guest & external proxy management. that’s a simple yet effective approach (and also cheap considering RB prices today). but it will be nice on research side if we can do the one RB option. Thank you for your reply, i will take your suggestion (apply 2 RB). Comment by lostbytes — November 12, 2012 @ 1:29 PM 108. I have two internet connection. One is PTCL (4 Mb) and other one is World Call (2mb). I want to USE RB 750GL for the load margin and Load balancing. Can you please give complete script for that. Comment by Waqar — November 19, 2012 @ 12:37 PM Reply 109. i am using 2 ISP for load balancing. I have facing problem when i run my FTP at that time my FTP didt connect. But when i swith off one line my ftv works properly. How can i run the FTP on bouth lans. Comment by Waqar — November 27, 2012 @ 7:49 PM Reply http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

30/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

You can exempt specific use or specific port from being processed by PCC. http://aacable.wordpress.com/2012/04/14/howto-exempt-any--website-from-mikrotik-pcc/ Comment by Syed Jahanzaib / Pinochio~:) — November 28, 2012 @ 10:15 AM Reply 110. Dear Sir … I have 4 WAN pppoe client and one Local using RB450G, how can I marege and bond all those 4 PPPoE Clients if my ISP doesn’t MLPPP . what should I do to merge all links ? any script ? Please Mr. Syed I need your help. Thanks. Comment by esalehnet — November 28, 2012 @ 8:30 PM Reply 111. Hi Sir, I have 4wan pppoe client and 1 local network, hot to merge all those pppoe client if my ISP doesn’t MLPPP ? any script ? what should I do in this case ? I need your help. Thank you very much. Comment by esalehnet — November 28, 2012 @ 9:04 PM Reply try the below link. http://mikrotikz.blogspot.com/2010/07/load-balance-mikrotik-with-pcc-using.html Comment by Syed Jahanzaib / Pinochio~:) — November 29, 2012 @ 3:15 PM Reply that load balancing and not merge my connection in one single link when I one single file, didn’t give me speed for all 4 WAN interfaces at once. I tried to put another mikrotik Routerboard by making 4 interfaces work as on single bonding using Balance rr method. what is the best method should I use to get merge these 4 interfaces, so when I start a file , I’ll get speed the total speeds for those 4 nterfaces connection? Comment by esalehnet — December 7, 2012 @ 8:41 PM 112. i am using 2 ISP for load balancing. I have facing problem when i run my FTP at that time my FTP didt connect. But when i swith off one line my ftv works properly. How can i run the FTP on both Lans, I try your script. But i still i have problem . can u explain it more for me Comment by Waqar — November 29, 2012 @ 7:03 PM Reply Wich Is the Best Methord Pcc Or Nth ? Comment by usma — December 9, 2012 @ 12:45 AM Reply 113. i have Question about Mikrotik Loadbalancing First if i have Two Wan 2Mb/s , with this method My Speed Increase to 4Mb/s ? ( 1 file with 4 Mb/s ) Another Question : i Think if i Established PPTP Vpn Connection on my Client PC it just Use one WAN , But if i Established PPTP on my Mikrotik i think it use 4Mb/s Tunnel and Direct Two WAN to Tunnel . is it Correct ? if yes can help me how can i Established PPTP Client on My Mikrotik and Direct 2 Wan on That tunnel ? ( i have 4Mb/s Tunnel ) Regards . Comment by Mehran — December 9, 2012 @ 2:13 PM Reply 114. salaM mere Pas mikrotek hotspot connection he…mgr porblem ye he her baar hona parta he…kia koi aisa method nai jis se auto mumkin ho sake…. Comment by raheel — December 12, 2012 @ 1:43 PM Reply Yes you can resister mac and by authentication for specific s. Howto By authentication for Few Clients This byes the hotspot by mac address. /ip hotspot ip-binding add mac-address=xx:xx:xx:xx:xx:xx type=byed (change xx:xx:xx:xx:xx:xx with your ’s mac address. You can also use the ip address to by. http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

31/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Read more about it here. http://aacable.wordpress.com/2011/09/12/mikrotik-hotspot-quick-setup-guide-cli-version/ Comment by Syed Jahanzaib / Pinochio~:) — December 13, 2012 @ 8:50 AM Reply 115. I Did it , and it work well . but just in manager it work well cause its Split connection and with Two wan . In Video Stream or many other things they use just One connection it use 1 Wan . there is no Way I can Split 1 Connection to 2 connection and see Video streaming or others with two wan ? Thanks . Comment by Mehran — December 13, 2012 @ 11:34 AM Reply 116. Is That possible to Torrents from 4th Gateway only please tell me example code for it. Comment by shahzad — December 14, 2012 @ 12:10 PM Reply 117. I have here a situation with my dual WAN Load Balancing. WAN2 = 384kb LS WAN1 = 6Mb ADSL Load Balancing on RB433 after this, WAN2 is fully used but WAN1 hardly reaches 2Mb and at the moment the LAN is reaching 1.5Mb, browsing is becoming almost impossible. My VOIP Calls are not more clear Using WAN1 alone, easily reaching 4Mb with no problem and can also Call. Plz Help Here is the configuration: /ip address add address=192.168.1.1/24 network=192.168.0.0 broadcast=192.168.0.255 interface=Local add address=192.168.2.2/24 network=192.168.1.0 broadcast=192.168.2.255 interface=WAN1 add address=192.168.11.2/24 network=192.168.11.0 broadcast=192.168.11.255 interface=WAN2 /ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=221.132.112.8,8.8.8.8 /ip firewall mangle add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2 add chain=prerouting dst-address=192.168.1.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.11.0/24 action=accept in-interface=Local add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting connection-mark=WAN1_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN1 add chain=prerouting connection-mark=WAN2_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN2 /ip route add dst-address=0.0.0.0/0 gateway=192.168.2.1 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.11.1 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.11.1 distance=2 check-gateway=ping /ip firewall nat add chain=srcnat out-interface=WAN1 action=masquerade add chain=srcnat out-interface=WAN2 action=masquerade /ip firewall mangle add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newhttp://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

32/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

connection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection newconnection-mark=WAN1_conn through=yes Comment by warren — December 14, 2012 @ 10:51 PM Reply Hi Warren, I am using 2 ISP with PCC method. But i am facing a problem with the FTP. When i try to through Filezilla my connect disconnect when both wan are working. But when i disable the one Wan i ma able to do a . Can you pleaes tell me how can i make my FTP working with both lan. Or how can i exempt the IP from PCC rule. Comment by waqar — December 15, 2012 @ 8:38 PM Reply Define your network topology in detail. If s are hitting directly to PCC , then you can use src-address as classifier as this way change of WAN ip wont occur for the , for the session he initially build with pcc. he will always be bound with the WAN that he initially connected to. Or you can also exclude some s ip / Traffic from being processed by pcc, means you can by certain traffic from being processed by the PCC, and this tagged tarffic will go via specific WAN only, http://aacable.wordpress.com/2012/04/14/howto-exempt-any--website-from-mikrotik-pcc/ Comment by Syed Jahanzaib / Pinochio~:) — December 16, 2012 @ 10:24 AM 118. Here is my new config but no change WAN1 = 384kb LS WAN2 = 6Mb ADSL /ip address add address=192.168.1.1/24 network=192.168.1.0 broadcast=192.168.1.255 interface=Local add address=192.168.11.2/24 network=192.168.11.0 broadcast=192.168.11.255 interface=WAN1 add address=192.168.2.2/24 network=192.168.2.0 broadcast=192.168.2.255 interface=WAN2 /ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=221.132.112.8,8.8.8.8 /ip firewall mangle add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2 add chain=prerouting dst-address=192.168.11.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting connection-mark=WAN1_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN1 add chain=prerouting connection-mark=WAN2_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN2 /ip route add dst-address=0.0.0.0/0 gateway=192.168.11.1 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.11.1 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=2 check-gateway=ping /ip firewall nat add chain=srcnat out-interface=WAN1 action=masquerade add chain=srcnat out-interface=WAN2 action=masquerade add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection newconnection-mark=WAN2_conn through=yes Comment by Warren — December 16, 2012 @ 9:06 PM Reply http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

33/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Will this force Local to send more traffic to WAN2 ? add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:5/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:5/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:5/2 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:5/3 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:5/4 action=mark-connection newconnection-mark=WAN2_conn through=yes Comment by Warren — December 17, 2012 @ 3:26 AM Reply Yes Comment by Syed Jahanzaib / Pinochio~:) — January 23, 2013 @ 3:41 PM 119. [...] view source [...] Pingback by Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | @rskabc — January 28, 2013 @ 7:16 AM Reply 120. Hello Bhai.. main 2 adsl(ptcl) modem ki loadbalancing ki huwi hai. using PCC method. its fine, . lakin jab aik Line disconnect hoti hai tu browsing main GateWay Timeout ka error aata jata hai. So how i can solve this problem….???? iam waiting for response thank you Hammad Hassan Fast ISP Comment by hammad hassan — February 5, 2013 @ 5:51 PM Reply 121. Assalamuaikum… thank you for this tutorial, but i have a question about : /ip firewall mangle add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes –> for that example “!local” [accept local] what is the ip address for local list..? there’s only ip address for client connection, or any others one..? thank you for help me.. Wassalamualaikum… Ronny Comment by Ronny Siswongso Nugroho — February 14, 2013 @ 2:39 PM Reply 122. Dear Sayed Jahanzaib… I have a pcc load balance where: WAN1: 8M up / 8M down (for direct connections) WAN2: 8M up / 8M down (for direct connections) WAN3: 35M down from sat (for port 80 connections) we are routing our sat subnet to use it for port 80 connections and every thing is ok… but we want to stop our sat down and upgrade our WAN2 to become 25M up / 50M down what we need is to divide the WAN2 bandwidth between the direct connections and port 80 connections to be like this : WAN1: 8M up / 8M down (for direct connections) WAN2: 8M up / 8M down (for direct connections) WAN2: 17M up / 42M down (for port 80 connections) ether2: my local lan ether3: my WAN1 (25M up / 50M down) ether4: my WAN2 (8M up / 8M down) what I need is to separate http connection from the PCC load balance and must from ether3 only … so can I solve it in this way ? : http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

34/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

/ip address add address=192.168.1.1/24 disabled=no interface=ether2 network=192.168.1.0 add address=1.1.1.2/24 disabled=no interface=ether3 network=1.1.1.0 add address=2.2.2.2/24 disabled=no interface=ether4 network=2.2.2.0 PCC load balance with marking http connection: /ip firewall mangle add action=mark-connection chain=forward disabled=no dst-port=80 new-connection-mark=http_conn through=yes protocol=t srcaddress=192.168.1.0/24 add action=mark-packet chain=forward connection-mark=http_conn disabled=no dst-port=80 new-packet-mark=http through=no protocol=t srcaddress=192.168.1.0/24 add action=accept chain=prerouting comment=ether3 disabled=no dst-address=1.1.1.0/24 in-interface=ether2 add action=accept chain=prerouting comment=ether4 disabled=no dst-address=2.2.2.0/24 in-interface=ether2 add action=mark-connection chain=prerouting comment=ether3_conn connection-mark=no-mark disabled=no in-interface=ether3 new-connectionmark=ether3_conn through=yes add action=mark-connection chain=prerouting comment=ether4_conn connection-mark=no-mark disabled=no in-interface=ether4 new-connectionmark=ether4_conn through=yes add action=mark-connection chain=prerouting comment=ether3_conn connection-mark=no-mark disabled=no dst-address-type=!local in-interface=ether2 new-connection-mark=ether3_conn through=yes per-connection-classifier=both-addresses-and-ports:2/1 add action=mark-connection chain=prerouting comment=ether4_conn connection-mark=no-mark disabled=no dst-address-type=!local in-interface=ether2 new-connection-mark=ether4_conn through=yes per-connection-classifier=both-addresses-and-ports:2/0 add action=mark-routing chain=prerouting comment=”ether3_packet mark” connection-mark=ether3_conn disabled=no in-interface=ether2 new-routingmark=to_ether3 through=yes add action=mark-routing chain=prerouting comment=”ether4_packet mark” connection-mark=ether4_conn disabled=no in-interface=ether2 new-routingmark=to_ether4 through=yes add action=mark-routing chain=output comment=”ether3_packet mark” connection-mark=ether3_conn disabled=no new-routing-mark=to_ether3 through=yes add action=mark-routing chain=output comment=”ether4_packet mark” connection-mark=ether4_conn disabled=no new-routing-mark=to_ether4 through=yes /ip firewall nat add action=accept chain=srcnat disabled=no dst-port=80 out-interface=ether3 protocol=t add action=masquerade chain=srcnat disabled=no out-interface=ether3 add action=masquerade chain=srcnat disabled=no out-interface=ether4 /ip route add check-gateway=ping comment=”Load balance_ether3″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=1.1.1.1 routing-mark=to_ether3 scope=30 target-scope=10 add check-gateway=ping comment=”Load balance_ether4″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=2.2.2.1 routing-mark=to_ether4 scope=30 target-scope=10 add check-gateway=ping comment=”Load balance_ether3″ disabled=no distance=1 dst-address=0.0.0.0/0 gateway=1.1.1.1 scope=30 target-scope=10 add check-gateway=ping comment=”Load balance_ether4″ disabled=no distance=2 dst-address=0.0.0.0/0 gateway=2.2.2.1 scope=30 target-scope=10 /queue simple add burst-limit=0/0 burst-threshold=0/0 burst-time=0s/0s direction=both disabled=no interface=all limit-at=0/0 max-limit=17M/42M name=”HTTP Queue” packet-marks=http parent=none priority=8 queue=ethernet-default/ethernet-default target-addresses=”” total-queue=default-small Comment by Fiber Net — February 17, 2013 @ 3:14 PM Reply 123. sorry edit : ether2: my local lan ether3: my WAN2 (25M up / 50M down) ether4: my WAN1 (8M up / 8M down) Comment by Fiber Net — February 17, 2013 @ 3:26 PM Reply 124. i have rb 1100 . ether 1: pppoe client ,local ether 2: pppoe client ,local ether 3: pppoe client ,local ether 4: pppoe client ,local ether 5: pppoe client ,local ether 6: pppoe client ,local all ether 1,2,3,4,5,6 have the same network 192.168.1.0 with DH 192.168.1.1/192.168.1.254 and i wont the output hotspot Comment by absal — February 18, 2013 @ 11:52 PM http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

35/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Reply 125. Asslam o Alaikum sir i am using rb 750 for loadbalcing in which 2 mb 4 mb 4mb connection used after dat os on syatem usinf pppoe net share bt ther is a problem that i used skype dafual speed gives me error ur net speed is slow give me solution plz Comment by waqar — February 26, 2013 @ 6:47 PM Reply 126. Can the setup work for me. I have to ISP, one is USM(ppp-client USB dongle) and the other one is with a router to mikrotik thru ether1. My Lan is on port 3 (hotspot-193.168.30.1/24), ether2 (10.11.6.1/24) and wlan1(192.168.2.1/24). I want a situation where the ppp-client USB will be my primary ISP (WAN1) and My secondary ISP will be from (ether1). How will my settings or configuration be so that if primary isp is down, the secodnary will come up and if primary comes up, it switches over to it. Comment by sapanda — March 5, 2013 @ 4:41 PM Reply You can setup netwatch to monitor wan connectivity usnig your specific primary interface, so when it stops receive response from google for example, then it should switch over to secondary ISP. Comment by Syed Jahanzaib / Pinochio~:) — March 6, 2013 @ 7:55 PM Reply 127. hello, i want to limit s internet bandwidth but i am having problem with internal connection. the internal bandwidth is also limited and it is affecting VOIP on the network. how can i solve this issue. thank you. i love your post and am a huge fan of yours… Comment by Rene — March 5, 2013 @ 8:32 PM Reply Its depend on the scenario. Are you running HOTSPOT ? Comment by Syed Jahanzaib / Pinochio~:) — March 6, 2013 @ 8:53 AM Reply Yes. am running hotspot on the network Comment by Rene — March 8, 2013 @ 4:07 PM HOTSPOT s can’t communicate with each other on LAN or PROXY-ARP issue If you face hotspot broadcast issue / arp-poisoning , problem, Remove the address pool from the Hotspot to turn off Universal NAT, /ip hotspot set address-pool=none OR /ip hotspot set numbers=hotspot1 address-pool=none OR /ip firewall nat add chain=pre-hotspot dst-address-type=!local hotspot=auth action=accept Comment by Syed Jahanzaib / Pinochio~:) — March 10, 2013 @ 7:14 PM the trixbox server is in the network. i want a situation where s would not be limited to the bandwidth given to them to access anything on the LAN. i already added the IP address of the sip server to bind and byed it; but its still slow and something jerky calls. Comment by Rene — March 11, 2013 @ 12:58 AM 128. Kindly describe this issue I am using ppc load balancing When I use torch tool I see this Dst. Vlan Tx Rate Rx Rate Tx Packeg 0.0.0.0 143.2Kbps 3.5Mbps 219 Comment by Ehtisham — March 8, 2013 @ 1:28 AM Reply tx means mikrotik is transmitting traffic to requesting target. Usually traffic rx means mikrotik is receiving traffic from the source. Usually Internet Comment by Syed Jahanzaib / Pinochio~:) — March 10, 2013 @ 7:16 PM Reply Thanks Bhai Comment by Ehtisham — March 31, 2013 @ 1:56 AM http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

36/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

129. is it possible to achieve the config through winbox? i have 2 adsl connections 15/1Mbps each one and i like to get them on my mikrotik 750 to get higher throughput and redundancy in case of one link fails. they are different ISPs and i can turn its modems in bridge mode. i have one network 192.168.190.0/24 Comment by aris — March 11, 2013 @ 7:02 PM Reply Yes you can configure mikrotik with PCC using WINBOX, in fact it will be musch easier if you use winbox because of GUI Comment by Syed Jahanzaib / Pinochio~:) — March 12, 2013 @ 8:59 AM Reply Is there any howto for the gui? Comment by aris — March 12, 2013 @ 12:39 PM No. but search on google there are few guides in GUI too. Comment by Syed Jahanzaib / Pinochio~:) — March 13, 2013 @ 9:55 AM 130. AoA, I need to know how to setup 2 adsl lines that traffic that coming to me(inbound) should be load balanced like web server hosted at my home does it work with mikrotik or dns load balancing will be required? Comment by gmsq — March 24, 2013 @ 6:31 PM Reply 131. hi thanks for script i use this script for 2 links 1 adsl (2m) and 1 wireless internet link (2m) load balancing work well and combine 2 link ==>4m but fail over not work correctly so test this i disconnect modem telephone cable and internet disconnected because ping rule only check next hop of internet link and not understand internet link is down i try resolved this problem with tool/netwatch and check 8.8.8.8 but not success can you help for improve fail over method with load balancing tanks a lot Comment by saeed — April 6, 2013 @ 8:45 PM Reply 132. Aslam O Alikum Syed Jahanzaib I am Tanveer ul isalm from Saudi Arabia, I just configure PPPoe and it working fine, but i have tow WAN connection. How i cam make only fail over. i no need loadbalance. please help me urgent or i want to monitor two wan IP ( yahoo or google), if it will not ping then it will shif to other gateway. if you can help in gui mode. Thanks in Advance. Regards, Tanveer Comment by Tanveer ul islam — April 10, 2013 @ 7:50 PM Reply Read below . . . http://aacable.wordpress.com/2013/04/12/mikrotik-multiple-wan-fail-over-scripts/ Comment by Syed Jahanzaib / Pinochio~:) — April 12, 2013 @ 4:16 PM Reply 133. What do I Need to Change to have 4 LAN Interfaces with different Networks in your script? Do I Need to add These additional LAN ports simply to the following lines and thts it or do I Need to Change more? add chain=prerouting dst-address=192.168.1.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.3.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.4.0/24 action=accept in-interface=Local Comment by Dirk — May 6, 2013 @ 6:55 PM Reply 134. i have 2 ISP primary is 192.168.10.10/24 connected to port ether 1 secondary is 10.10.10.10/24 connected on port ether 2 and LAN is 172.16.0.1/16 connected on port ether3. please kindly provide me the dual ISP fail-over scripts. Comment by Naveed — May 12, 2013 @ 3:00 PM Reply sorry didn’t mention RB 1100AHx2 http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

37/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Comment by Naveed — May 12, 2013 @ 3:02 PM Reply Here you go . . . http://aacable.wordpress.com/tag/mikrotik-fail-over/ Comment by Syed Jahanzaib / Pinochio~:) — May 13, 2013 @ 8:38 AM Reply 135. Hi there! I will like to set up 2 WAN Load Balancing using PCC method. but these two line are not equal. the first one has 06mb and the second one has 1mb. all are Optic Fiber links. can someone please advice? Comment by Alex — May 29, 2013 @ 2:54 AM Reply PCC is not very good with un equal links. but you can try by adding more pcc rule for high end wan. see the examples in the article. Comment by Syed Jahanzaib / Pinochio~:) — June 12, 2013 @ 2:24 PM Reply 136. Hello Sir, I was wondering if it is possible to load balance more than 30 PPPOE connections. What mikrotik router do you advice? What is your advice in load balancing that many connections? Comment by HRDHKR — July 9, 2013 @ 2:52 AM Reply I will not recommend you to go with that much pppoe connections, as troubleshooting will become very hard. anyhwo still you can do it, ing larger files with idm type tools will be greatly benefited. No RB have 30 ports, however you can use VLAN technology to do as much as ports config you like. I once saw 22 WAN LB at a friends rb suing this tech. Comment by Syed Jahanzaib / Pinochio~:) — July 9, 2013 @ 8:09 AM Reply 137. Hi, I am using RB 1100 of V6.0rc11 I have two internet connections. One connection gives static Ip Address ie. on ether10 —- 111.112.113.114 (ISP1) and other is PPPOE Connection gives dynamic ip address on ether9 (ISP2) I have LAN on ether1 —– 192.168.0.0/24 my nat rule is add action=masquerade chain=src-nat Src. Address=192.168.0.0/24 out-interface=ISP1 (internet for all) i tried add action=masquerade chain=src-nat Src. Address=192.168.0.100 out-interface=ISP2 (internet for particular computer) And add action=masquerade chain=src-nat Src. Address=192.168.0.101 out-interface=ISP1 (internet for particular computer) What I want is to route all traffic from ISP2 of ip —192.168.0.100 and ip–192.168.10.101 Please Help Comment by cool nicq — July 13, 2013 @ 2:42 PM Reply 138. bhai kia hum is script k saat quality of service ko apply kar saktey hain or kese kindly guide,we are facing problem with browsing although ing speed is fine. Comment by Ehtisham — August 14, 2013 @ 2:57 PM Reply Hi … I’m using LB with 8 PPPoE Clients and all working fine. I having problem with the smtp port 25 in outlook, all s can recieve emails by pop3 port 110, but they cannot do send. When I connect all s direct to one PPPoE client without using LB like a simple router, they can sends emails smoothly. I’ve add a rule in the mangle with prerouting chain, T Protocol, Dst. Port 25 and action accept, and nothing. Please what should I do to fix this problem ? Help… Comment by esalehnet — August 19, 2013 @ 3:21 PM

http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

38/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Reply 139. Hello Syed, Below find config related to Mikrotik RB750G router, running 6.0rc9. I am trying to configure ISP redundancy in load-balancing mode through a PCC article. I have three connected interfaces, LAN, WAN and WAN2. The Primary and secondary WAN connections have different speed. Issue is that after configuring the router, I get no traffic on one of the firewall>mangle prerouting chain rules (for WAN). The same applies when I disable the secondary interface (WAN2) there is no automatic changeover to the primary interface. Some observations I’ve noted through WebFig are the following: Interface>Interface – Ok, Traffic being Transmitted and Received on all three interfaces Interface>Ethernet – Ok, Traffic being Transmitted and Received on all three interfaces DNS – Four set, two for one ISP and two for the other ISP Firewall>NAT – seems ok, traffic being transmitted and received on all interfaces Firewall>Mangle – there seems to be an issue here since there is no packets (counter still at 0), are flowing for primary ISP network addresses. Rule is as follows: /ip firewall mangle Add chain=prerouting dst-address=XXXX action=accept in-interface=LAN —————– Note that all seems ok with the remaining prerouting (mark connection and mark routing) rules, since traffic is flowing. This includes the prerouting rule for the other WAN link. Routes>Primary ISP Gateway is unreachable for static routes Routes>Nexthops Primary and secondary gateways are reachable for both nexthops Below I am including extracts of the config. (Please note that IP addresses/MAC Addresses have been left out and replaced with Text). Should you require further info please let me know [@MikroTik] /interface> print Flags: D – dynamic, X – disabled, R – running, S – slave # NAME TYPE MTU L2MTU MAX-L2MTU MAC-ADDRESS 0 R WAN ether 1500 1520 1520 – 1 R LAN ether 1500 1520 1520 – 2 R WAN2 ether 1500 1520 1520 – 3 XS ether4-slave-local ether 1500 1520 1520 – 4 XS ether5-slave-local ether 1500 1520 1520 – — [@MikroTik] /ip address> print Flags: X – disabled, I – invalid, D – dynamic # ADDRESS NETWORK INTERFACE 0 ;;; default configuration 192.168.88.1/24 192.168.88.0 LAN 1 ;;; Internet Primary ISP1 IP Address [ISP1 Network Address] WAN 2 ;;; Internet Secondary ISP2 IP Address [ISP2 Network Address] WAN2 — [@MikroTik] /ip firewall mangle> print Flags: X – disabled, I – invalid, D – dynamic 0 chain=prerouting action=accept dst-address=[ISP1 Network Address] in-interface=LAN 1 chain=prerouting action=accept dst-address=[ISP2 Network Address] in-interface=LAN 2 chain=prerouting action=mark-connection new-connection-mark=WAN_conn through=yes in-interface=WAN connection-mark=no-mark 3 chain=prerouting action=mark-connection new-connection-mark=WAN2_conn through=yes in-interface=WAN2 connection-mark=no-mark 4 chain=prerouting action=mark-connection new-connection-mark=WAN_conn through=yes dst-address-type=!local in-interface=LAN connection-mark=no-mark per-connection-classifier=both-addresses:2/0

5 chain=prerouting action=mark-connection new-connection-mark=WAN2_conn through=yes http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

39/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

5 chain=prerouting action=mark-connection new-connection-mark=WAN2_conn through=yes dst-address-type=!local in-interface=LAN connection-mark=no-mark per-connection-classifier=both-addresses:2/1 6 chain=prerouting action=mark-routing new-routing-mark=to_WAN through=yes in-interface=LAN connection-mark=WAN_conn 7 chain=prerouting action=mark-routing new-routing-mark=to_WAN2 through=yes in-interface=LAN connection-mark=WAN2_conn 8 chain=output action=mark-routing new-routing-mark=to_WAN through=yes connection-mark=WAN_conn 9 chain=output action=mark-routing new-routing-mark=to_WAN2 through=yes connection-mark=WAN2_conn ————– [@MikroTik] /ip firewall nat> print Flags: X – disabled, I – invalid, D – dynamic 1 chain=srcnat action=masquerade out-interface=WAN 2 chain=srcnat action=masquerade out-interface=WAN2 ————– [@MikroTik] /ip route> print Flags: X – disabled, A – active, D – dynamic, C – connect, S – static, r – rip, b – bgp, o – ospf, m – mme, B – blackhole, U – unreachable, P – prohibit # DST-ADDRESS PREF-SRC GATEWAY DISTANCE 0 0.0.0.0/0 ISP1 Gateway 1 1 0.0.0.0/0 ISP2 Gateway 2 2 0.0.0.0/0 ISP1 Gateway 1 (routing mark to_WAN) 3 0.0.0.0/0 ISP2 Gateway 2 (routing mark to_WAN2) 4 ADC 192.168.88.0/24 192.168.88.1 LAN 0 5 ADC ISP1 Network Address ISP1 Static IP WAN 0 6 ADC ISP2 Network Address ISP2 Static IP WAN2 0 Comment by Joseph Lee Lemon — August 27, 2013 @ 5:45 PM Reply 140. rocket m2 kay ubnt sactor 120 degree ka laga hi 1 km par 72 mb par conect ho kar thori dair tak 1 mb par a jata hi ya masla samaj nhi a raha plz help me Comment by rashid — September 3, 2013 @ 3:05 PM Reply sorry bro. No idea for wireless related issues. Comment by Syed Jahanzaib / Pinochio~:) — September 4, 2013 @ 1:19 PM Reply 141. Hello Syed, Any Idea on 139, i.e. ISP redundancy with PCC Much obliged, Joe Comment by Joseph Lee Lemon — September 4, 2013 @ 6:15 PM Reply 142. Plz help me with a scrip for RB750 Comment by tanveer — September 29, 2013 @ 9:53 PM Reply 143. does this method consume traffic from both links equally ?? Comment by Khuffash — October 3, 2013 @ 5:38 PM Reply YES if multiple http connections generated, like IDM or multiple requests on load Comment by Syed Jahanzaib / Pinochio~:) — October 4, 2013 @ 10:34 AM http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

40/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Reply 144. we are using 3 WAN connection, i study ur documents which helps a lot, internet is working fine but the problem is that when i use web email or remote desktop from outside network (abroad) its drops after some time, can you please guide me how to fix this issue. Comment by Friends — October 10, 2013 @ 1:06 PM Reply 145. but what if i do this in ip routes ?? what is the dif between the picture and between ur route role ?? or /ip route add dst-address=0.0.0.0/0 gateway=192.168.1.1 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.1.1 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=2 check-gateway=ping Comment by qassam mahmoud — October 18, 2013 @ 10:32 PM Reply 146. Bhai, Assalamu Alaikum Wa Rahmatullah. I am Kawsar from Bangladesh. I just configured your given 2XWan Script on My Mikrotik 450G and put two modem (1XWimax-2MB Line+1XADSL-512 Kbps). Every script is okey. But my system is not working. I am not clear which DNS should I use and also is there any necessity to put up real IP which has given by two ISP (1 from Wimax and 1 from ADSL)? I didn’t put that. Here I am giving the whole script which I have given to my Mikrotik. If you see and help me. I will be grateful. Please have a look with my used script. /ip address add address=192.168.0.1/24 network=192.168.0.0 broadcast=192.168.0.255 interface=Local add address=192.168.1.2/24 network=192.168.1.0 broadcast=192.168.1.255 interface=WAN1 add address=192.168.2.2/24 network=192.168.2.0 broadcast=192.168.2.255 interface=WAN2 /ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=221.132.112.8,8.8.8.8 /ip firewall mangle add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2 add chain=prerouting dst-address=192.168.1.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting connection-mark=WAN1_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN1 add chain=prerouting connection-mark=WAN2_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN2 /ip route add dst-address=0.0.0.0/0 gateway=192.168.1.1 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.1.1 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=2 check-gateway=ping /ip firewall nat add chain=srcnat out-interface=WAN1 action=masquerade add chain=srcnat out-interface=WAN2 action=masquerade Thanks Kawsar +8801711865172 [email protected] Comment by Md Sarwar E Kawsar — November 4, 2013 @ 10:24 PM Reply 147. Hi Sir

I have 2 Dynamic IP Addresses (dsl) lines…. I am using Afraid.org auto dns updater… the system is load balancing setup…. It seems to be working fine, http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/ 41/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

I have 2 Dynamic IP Addresses (dsl) lines…. I am using Afraid.org auto dns updater… the system is load balancing setup…. It seems to be working fine, untill both dynamic ip addresses change on the wan 1 and wan 2….. is there a script that can force my IP updater to go only through wan 1, or through wan 2 which I can select myself?…. It somehow seems to affect my voip system as well… now i have to reboot my voip server everytime the IP changes as well… Kind regards Comment by jackalt007Nizam — November 7, 2013 @ 2:46 AM Reply Oh yes…. Using RB750… Comment by jackalt007Nizam — November 7, 2013 @ 12:33 PM Reply 148. sir , jab main yeh 2 wan lod balniceing karta ho to interface main rx errors ata ha plz reply Comment by shshid — November 8, 2013 @ 11:34 AM Reply 149. […] http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-s… […] Pingback by Link to mikrotik Multiwan | Plovelog’s Weblog — November 12, 2013 @ 10:45 PM Reply 150. why do u use add chain=prerouting dst-address=192.168.1.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.2.0/24 action=accept in-interface=Local I mean “192.168.1.0/24″ and “192.168.2.0/24″. Because this is WAN network. This is not my property. This is service provider’s network. Please explain me. Thanks in advance. Comment by myfahimFahim Ahmed — November 19, 2013 @ 3:15 PM Reply Thanks Dear, I just update my wimax modem local IP as 192.168.1.0/24 and 192.168.2.0/24. That’s why I used those twice IP as well. One thing let me describe you. When I just start the two wimax modem at a time just WAN1 modem is using. If I make disable WAN1 then WAN2 is automatically starts its duty. Means this time WAN2 is working. At a time both is not working. I would like to get both modems data means (WAN1-2MB and WAN2-2MB=Local4MB). Is it possible to get 4 MB speed at a time by the said two wimax modem? Thanks Kawsar [email protected] Comment by Arfan — November 23, 2013 @ 2:19 PM Reply 152. Hello, I have two Fiber Optic links with /29 IP subnet and gateway IP is on ISP hardware(so I can only use 5 public IPs from each link) , how can I configure Loadbalancer to fit my scenario???.I have tried the script but it force traffic only to one link the second not working or when I disconnect the first one it’s start to force to second one. Thank you in advance Comment by Mojitos_82 — December 12, 2013 @ 4:02 AM Reply It depends on how your mikrotik box is configured with other services. If only one link is in used, probably something in config is configured incorrectly. Once PCC script cannot fit in all environment, for example, if you have PCC with PPPoE server in box, or PCC with HOTSPOT, or simple PCC as a gateway, settings are different for each scenario.

http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

42/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Comment by Syed Jahanzaib / Pinochio~:) — December 12, 2013 @ 8:24 AM Reply Hi, Thank’s for reply, I need simple pcc loadbalancer .But I preffer to use loadbalancing on my PPPoE concentrator directly, on RB1100AH . Is it possible? I have configured for now PORT 13 as WAN port and port 6 as LAN master and the rest port 7-10 as slave ports ,11-12 ports don’t have idea how to use them.I running ROS 6.6 on RB. Please help! Comment by Mojitos_82 — December 13, 2013 @ 11:37 PM 153. hi, please sir, i want to know if it is possible to use two 2 internet service provider, isp1 for browsing and isp2 for ing on mikrotik, thank you Comment by lateef — December 26, 2013 @ 5:29 PM Reply 154. hi sir my question is the rb 740 can combine 4 network for example 10Mb+10Mb+10Mb+10Mb combine 40Mb it is possible Comment by imran rasool — January 14, 2014 @ 10:25 PM Reply Yes It can. See following for a comparison … http://routerboard.com/RB750 Comment by Syed Jahanzaib / Pinochio~:) — January 17, 2014 @ 7:22 PM Reply 155. Dear sir assalamo alaikum sir i am having a problem on my network dh lease busy and that time whole the network yellow sign and not accept any ip address manually kindly tell me the solution i am very upset for this problem i am using mikrotik 5.20 hotspot Comment by Muhammad Ali — January 17, 2014 @ 2:00 AM Reply 156. I have 2 wan with 4 and 8 mbps. Which one of the following pcc is correct. add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection newconnection-mark=WAN2_conn through=yes OR add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:3/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:3/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:3/2 action=mark-connection newconnection-mark=WAN2_conn through=yes Notice the ‘2’ and ‘3’ in the pcc.. Thank you for the answer. Comment by freerhyme — February 11, 2014 @ 12:03 PM Reply 157. How to update this script if i have one WAN with PPPoE and both WANs has adresses from DH and may change? I can use 192.168.1.1. and 192.168.2.1. Can it be changed to interface? Comment by LiveBomb — February 24, 2014 @ 2:48 PM Reply 158. i have 2 Wan, of 4mb each, WAN1 has volume of 102gb, WAN2 no volume quota: i wish to load balance my surf to WAN1 and all s to WAN2: can you help me please;i have a network which clients can more than 200gb per month and need to reduce cost Comment by loknjinu — March 3, 2014 @ 3:29 PM Reply 159. Is it possible on MikroTik i can LoadBalancing with Single Socket Connection ? i mean For Streaming Video and etc it just use one Session , Connectify Switchboard is a Application can do it and used Multiple Internet Connection for Streaming Videos . http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

43/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Now i want know Mikrotik is able to do that ? -Thanks . Comment by Mehran — March 15, 2014 @ 3:33 PM Reply 160. hello, thanks for your great works with this blog but I would like to find out; I recently bought an RB2011 and I’m expecting my ISP to install a second connection. Can I have the load balancing as well as hotspot setup on the same router? Thanks, Max Comment by maxcuban — March 24, 2014 @ 1:20 PM Reply 161. hi, I have written on many forums without ever answer, but I need help, I have 2 WAN from a 4mb and from a 7mb, I would like to achieve load balancing and I used this script /ip address add address=192.168.1.1/24 network=192.168.1.0 broadcast=192.168.1.255 interface=Local add address=192.168.10.2/24 network=192.168.1.0 broadcast=192.168.10.255 interface=WAN1 add address=192.168.20.2/24 network=192.168.2.0 broadcast=192.168.20.255 interface=WAN2 /ip dns set allow-remote-requests=yes cache-max-ttl=1w cache-size=5000KiB max-udp-packet-size=512 servers=217.112.96.190,8.8.8.8 /ip firewall mangle add chain=input in-interface=WAN1 action=mark-connection new-connection-mark=WAN1_conn add chain=input in-interface=WAN2 action=mark-connection new-connection-mark=WAN2_conn add chain=output connection-mark=WAN1_conn action=mark-routing new-routing-mark=to_WAN1 add chain=output connection-mark=WAN2_conn action=mark-routing new-routing-mark=to_WAN2 add chain=prerouting dst-address=192.168.10.0/24 action=accept in-interface=Local add chain=prerouting dst-address=192.168.20.0/24 action=accept in-interface=Local add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/0 action=mark-connection newconnection-mark=WAN1_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/1 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting dst-address-type=!local in-interface=Local per-connection-classifier=both-addresses-and-ports:2/2 action=mark-connection newconnection-mark=WAN2_conn through=yes add chain=prerouting connection-mark=WAN1_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN1 add chain=prerouting connection-mark=WAN2_conn in-interface=Local action=mark-routing new-routing-mark=to_WAN2 /ip route add dst-address=0.0.0.0/0 gateway=192.168.10.1 routing-mark=to_WAN1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.20.1 routing-mark=to_WAN2 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.1.1 distance=1 check-gateway=ping add dst-address=0.0.0.0/0 gateway=192.168.2.1 distance=2 check-gateway=ping /ip firewall nat add chain=srcnat out-interface=WAN1 action=masquerade add chain=srcnat out-interface=WAN2 action=masquerade but I do not understand why, or where I’m wrong but problems steaming, https web sites you can help me solve the problem? please Comment by antosere — April 2, 2014 @ 1:53 AM Reply 162. Hey there. its sam I was looking over one of my 2 WAN PPC on a rb450G (ports 4-5) and i noticed i am using a Bridge for ports 1-3. Should i be using a Master port vs Bridge? Any performance issues i could incur doing this? No idea why i am using a bridge. I think it came out of the box with a bridge on the rb450G vs master/slave. its running 4.14 Comment by Sam — April 5, 2014 @ 10:45 AM Reply

163. how it can possible rb 750 combine two or more network http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

44/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

163. how it can possible rb 750 combine two or more network i.e 4Mb+4Mb=8Mb. how it is posible reply my email [email protected] Comment by imran — April 7, 2014 @ 12:30 AM Reply 164. Sir i am Babu i wants to easy solution Auto redundancy from mikrotik plz help me.. Comment by Babu — April 7, 2014 @ 9:25 AM Reply Sir plz help me…. Comment by Babu — April 7, 2014 @ 10:30 AM Reply 165. Sir i think you have lot of experience in mikrotik so i wants to help auto redundancy script.i am wait for your mail. Comment by Babu — April 9, 2014 @ 10:15 AM Reply You want to load balance two wan connections? or you want primary / secondary fail over? Comment by Syed Jahanzaib / Pinochio~:) — April 10, 2014 @ 8:52 AM Reply 166. Sorry Sir load balance i am ok but i wants to help auto redundancy script i don’t know redundancy men primary / secondary fail over ? plz help me….. Comment by Babu — April 11, 2014 @ 4:07 PM Reply http://aacable.wordpress.com/2013/04/12/mikrotik-multiple-wan-fail-over-scripts/ Comment by Syed Jahanzaib / Pinochio~:) — April 11, 2014 @ 10:45 PM Reply 167. Thank Sir i will try it . Comment by Babu — April 12, 2014 @ 4:57 PM Reply 168. Assalamu walaikum Vaijan, I want to know can i torrent bandwidth my 2nd wan link? Can you please help me. Comment by Salim Rahman — April 15, 2014 @ 9:45 AM Reply 169. i have 2 isp’s and im using Rb750 …. i want certain traffics to be ruled like facebook,youtube ,DL and others browsing will go only to ISP1 and my ISP2 will be my gaming isp pls help thanks in advance Comment by nhelly — June 1, 2014 @ 9:11 AM Reply 170. Sir Syed Jahanzaib ! salam ! i have two connection of wan one is DSL and the other one is the fiber optic connection. i want to merge both connection to get the double bandwidth and also have to do fail-over can you do it for me via team-viewer, as i am newbie to the mikrotik i need your help please ! And this will also be a great chance for to learn something Comment by Ismail khan — June 11, 2014 @ 2:58 PM Reply 171. Sir Salam ! I am using RB 450 . I have install two ISP in the device and I am using PCC method for load balancing. All the Things are running perfectly alright. But I am facing problem with the FTP file zilla software. When I try to with the software with active two isp I got the disconnection. After that I disable one connection and I tried the File ziila software. Its works fine. Can you help me in this matter. How can I exempt the IP PCC rules.plz help me . http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

45/46

8/10/2014

Mikrotik DUAL WAN Load Balancing using PCC method. Complete Script ! by zaiB | Syed Jahanzaib Personnel Blog to Share Knowledge !

Comment by Babu — July 7, 2014 @ 5:32 PM Reply Sir plz help me…. Comment by Babu — July 7, 2014 @ 5:46 PM Reply have you read this ? http://aacable.wordpress.com/2012/04/14/howto-exempt-any--website-from-mikrotik-pcc/ Comment by Syed Jahanzaib / Pinochio~:) — July 9, 2014 @ 9:36 AM Reply 172. hi,i have to links WAN1(10mb up 512k down) and WAN2(1mb up 5mb down),i want to use both links having WAN1 as my and WAN2 as my ….how do i configure?? i hace ccr 12g Comment by Jim — July 25, 2014 @ 11:16 PM Reply 173. correction….hi,i have to links WAN1(10mb down 512k up) and WAN2(1mb down 5mb up),i want to use both links using WAN2 as my main ….how do i configure?? i hace ccr 12g Comment by Jim — July 25, 2014 @ 11:18 PM Reply 174. Dear Jahanzaib Sir, I have two WAN Links WAN1=203.80.130.74, 255.2555.255,252, DGW=203.80.130.73, DNS-203.80.130.1 WAN2 = DSL Model 10.92.4.2 please advise me how can configure failover router. Regards Abdul Wahab Sukkur Comment by Abdul Wahab — August 17, 2014 @ 2:48 PM Reply RSS (Really Simple Syndication) feed for comments on this post. TrackBack URI (Uniform Resource Identifier) The Silver is the New Black Theme. Blog at WordPress.com. Follow

Follow “Syed Jahanzaib Personnel Blog to Share Knowledge !” Powered by WordPress.com

http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/

46/46