Nms Installation q512

NMS installation

NMS installation 1.Creat a Virtual Network.

2.DATABASE IP SETTING

3.install the MySQL server

4.OTNM 2000 installation

1.Creat a Virtual Network. 1  To install virtual network card wright click on “My computer” located on the desktop. Select “Manage”. Then select “Device Manager”.  right click on “ Name” Example I clicked “DiponkarGhosh” here. Select “Add legacy hardware”.

3

2

1.Creat a Virtual Network. Here you see new window comes up. Click “Next”.

1.Creat a Virtual Network. Select “Install the hardware that I manually select from a list.(advance)”.

1.Creat a Virtual Network. Select “Network adapters” then click next.

1.Creat a Virtual Network. Select “Microsoft” in the left side of the table and select “Microsoft Loopback Adapter” from the wright side of the table. Click “Next” and then click finish.

2.DATABASE IP SETTING (1)Now Go to Network And Sharing Center. And Change “Adapter Setting” Select “Microsoft Loopback Adapter”

(2)Right Click on Microsoft Loopback Adapter and select “Propertise”

(3)From the propertise select the “Internet Protocol Version 4(T/IPv4)” Double click on it.

2.DATABASE IP SETTING (4)Select “Use the following IP address” This IP is given from fiberhome, put this new IP address and put subnet mask then click ok. This is your database IP.

3.install the MySQL server.  To install MySQL copy the Mysql folder in the Drive “D”.  Keep in mind that the Mysql folder should not contain any other folder in it.  Now From the “Start” menue Run the “Command prompt” as . Run these commands as follow: C:\Document and Settings\>d: D:\>cd mysql\bin D:\ mysql\bin>mysqld.exe -install MySQL --defaults-file=\"d:\mysql\my.ini\"

After in the command prompt it shows “Service successfully installed” then installation is complete

3.install the MySQL server Now we need to start the service of Mysql just we installed . To start the service.. Right click“My Computer” then Select “Manage” then select “services and applications” then select “services”. From the list of services select the “Mysql” and right click on Mysql and start the service.

4.OTNM 2000 installation (1)Right click on “Setup.V2.0R5(Build04.20.05.50BD4)” and run as .

4.OTNM 2000 installation (2)Click “Next”

4.OTNM 2000 installation (3)Click “Yes”

4.OTNM 2000 installation (4)Click “Next”

4.OTNM 2000 installation (5)Select “English “

4.OTNM 2000 installation

(6)Select “Server mode”

4.OTNM 2000 installation (7)Then select “Mysql”

4.OTNM 2000 installation (8)Add the Customer “IP address” here, which is given from the customer and earlier you put it on the microsoft loopbacl adaptar. This is your database IP address.

Here we must sellct the IP to 100.1.1.0

4.OTNM 2000 installation (9)Software will be installed in the same drive MySQL is installed . Do not modify anything here. This software must be installed in the same drive same folder MySQL is installed. Click “Next”

4.OTNM 2000 installation (10)Typical is selected We dont need to modify it now, Click “Next”

4.OTNM 2000 installation (11)Click “Next”

4.OTNM 2000 installation (12)Software will now install autometically wait for couple of minutes till the finish window comes.

4.OTNM 2000 installation (13)Run the cmd as and put these commands as follow: D: cd otnm\md\alldb\mysql cd otnm\md\alldb\mysql>creatalldbroot.cmd

4.OTNM 2000 installation (14)Copy the otnm2000.lic file which is given by Fiberhome to “D\OTNM\md\bin” to replace it .

4.OTNM 2000 installation Now You need to start all the EMS services  To start the EMS services go to D:\OTNM\ui\sbin\service  Run as start_ems_main_service” You can also run the services manually.  Now check all the services are started or not by Right Clicking to My Copmputer then select on propertise then select Services and double click on “services”

 Select EMS services and start All EMS services Which are not Disabled. Do not do anything with Disabled services.

4.OTNM 2000 installation Now Select the OTNM2000 on Desktop and using as .

Thank you!