Noja-522-06 Rc10 Dnp3 Device Profile 61693p

NOJA-522-06

DNP3 Device Profile Document For

NOJA Power

®

Switchgear

RC10 Controller Revision Date: 09-01-2014

NOJA-522-06

DEVICE PROFILE REVISION HISTORY Rev

Author

Date

5

BOS/AZ

14-05-2013

Added new points. T, MDI and LGVT included.

Comment

6

OA

09-01-2014

Negative Phase Sequence and Changes to Live Line

Source: S:\Marketing-500\ Manuals\SCADA Protocols\ NOJA-522-06 RC10 DNP3 Device Profile.docx

NOJA Power® and OSM® are ed trademarks of NOJA Power Switchgear Pty Ltd. This document is copyright and is intended for s and distributors of NOJA Power Switchgear product. It contains information that is the intellectual property of NOJA Power Switchgear and the document, or any part thereof, should not be copied or reproduced in any form without written permission from NOJA Power Switchgear. NOJA Power Switchgear applies a policy of ongoing development and reserves the right to change product without notice. NOJA Power Switchgear does not accept any responsibility for loss or damage incurred as a result of acting or refraining from action based on information in this Manual.

© NOJA Power Switchgear Pty Ltd 2002 - 2014 www.nojapower.com.au

DNP3 Device Profile Document Vendor Name: NOJA Power® Switchgear Device Name: RC10 Controller

NOJA-522-06

Page 2 09-01-2014

NOJA-522-06 Contents 1 1.1

Introduction......................................................................................................................................... 7 Device Identification .......................................................................................................................... 9 1.1.1 Device Function: ...................................................................................................................... 9 1.1.2 Vendor Name: .......................................................................................................................... 9 1.1.3 Device Name: ........................................................................................................................... 9 1.1.4 Device manufacturer’s hardware version string: ...................................................................... 9 1.1.5 Device manufacturer’s software version string: ....................................................................... 9 1.1.6 Device Profile Document Version Number: .......................................................................... 10 1.1.7 DNP Levels ed for: .................................................................................................... 10 1.1.8 ed Function Blocks: ................................................................................................... 10 1.1.9 Notable Additions: ................................................................................................................. 11 1.1.10 Methods to set Configurable Parameters: .............................................................................. 11 1.1.11 DNP3 XML files available On-Line: ..................................................................................... 11 1.1.12 External DNP3 XML files available Off-line: ....................................................................... 12 1.1.13 Connections ed: ......................................................................................................... 12 1.2 Serial Connections ............................................................................................................................ 13 1.2.1 Port Name............................................................................................................................... 13 1.2.2 Serial Connection Parameters: ............................................................................................... 13 1.2.3 Baud Rate: .............................................................................................................................. 13 1.2.4 Hardware Flow Control (Handshaking): ................................................................................ 13 1.2.5 Interval to Request Link Status: ............................................................................................. 14 1.2.6 s DNP3 Collision Avoidance: .................................................................................... 14 1.2.7 Receiver Inter-character Timeout:.......................................................................................... 15 1.2.8 Inter-character gaps in transmission: ...................................................................................... 15 1.3 IP Networking................................................................................................................................... 16 1.3.1 Port Name............................................................................................................................... 16 1.3.2 Type of End Point: ................................................................................................................. 16 1.3.3 IP Address of this Device: ...................................................................................................... 16 1.3.4 Subnet Mask: .......................................................................................................................... 16 1.3.5 Gateway IP Address: .............................................................................................................. 16 1.3.6 Accepts T Connections or UDP Datagrams from: ............................................................ 16 1.3.7 IP Address(es) from which T Connections or UDP Datagrams are accepted: .................. 16 1.3.8 T Listen Port Number: ....................................................................................................... 16 1.3.9 T Listen Port Number of remote device: ........................................................................... 17 1.3.10 T Keep-alive timer: ........................................................................................................... 17 1.3.11 Local UDP port: ..................................................................................................................... 17 1.3.12 Destination UDP port for DNP3 Requests (Master Only): .................................................... 17 1.3.13 Destination UDP port for initial unsolicited null responses (UDP only Outstations): ........... 17 1.3.14 Destination UDP port for responses: ...................................................................................... 17 1.3.15 Multiple outstation connections (Masters only): .................................................................... 18 1.3.16 Multiple master connections (Outstations Only):................................................................... 18 1.3.17 Time synchronization : ............................................................................................... 18 1.4 Link Layer ........................................................................................................................................ 19 1.4.1 Data Link Address:................................................................................................................. 19 1.4.2 DNP3 Source Address Validation: ......................................................................................... 19 1.4.3 DNP3 Source Address(es) expected when Validation is Enabled: ........................................ 19 1.4.4 Self Address using address 0xFFFC: ........................................................................ 19 1.4.5 Sends Confirmed Data Frames: ..................................................................................... 19 DNP3 Device Profile Document Vendor Name: NOJA Power® Switchgear Device Name: RC10 Controller

NOJA-522-06

Page 3 09-01-2014

NOJA-522-06 1.4.6 Data Link Layer Confirmation Timeout: ............................................................................... 20 1.4.7 Maximum Data Link Retries: ................................................................................................. 20 1.4.8 Maximum number of octets Transmitted in a Data Link Frame: ........................................... 20 1.4.9 Maximum number of octets that can be Received in a Data Link Frame: ............................. 20 1.5 Application Layer ............................................................................................................................. 21 1.5.1 Maximum number of octets Transmitted in an Application Layer Fragment other than File Transfer: 21 1.5.2 Maximum number of octets Transmitted in an Application Layer Fragment containing File Transfer: 21 1.5.3 Maximum number of octets that can be Received in an Application Layer Fragment: ......... 21 1.5.4 Timeout waiting for Complete Application Layer Fragment: ................................................ 22 1.5.5 Maximum number of objects allowed in a single control request for CROB (group 12): ..... 22 1.5.6 Maximum number of objects allowed in a single control request for Analog Outputs (group 41): 22 1.5.7 Maximum number of objects allowed in a single control request for Data Sets (groups 85,86,87): 22 1.5.8 s mixing object groups (AOBs, CROBs and Data Sets) in the same control request:22 1.6 Fill Out The Following Items For Masters Only .............................................................................. 23 1.7 Fill Out The Following Items For Outstations Only......................................................................... 24 1.7.1 Timeout waiting for Application Confirm of solicited response message: ............................ 24 1.7.2 How often is time synchronization required from the master? .............................................. 24 1.7.3 Device Trouble Bit IIN1.6: .................................................................................................... 24 1.7.4 File Handle Timeout: ............................................................................................................. 24 1.7.5 Event Buffer Overflow Behavior: .......................................................................................... 24 1.7.6 Event Buffer Organization: .................................................................................................... 25 1.7.7 Sends Multi-Fragment Responses: ......................................................................................... 25 1.7.8 Last Fragment Confirmation: ................................................................................................. 25 1.7.9 DNP Command Settings preserved through a device reset: ................................................... 25 1.8 Outstation Unsolicited Response ........................................................................................ 26 1.8.1 s Unsolicited Reporting: ............................................................................................ 26 1.8.2 Master Data Link Address:..................................................................................................... 26 1.8.3 Unsolicited Response Confirmation Timeout: ....................................................................... 26 1.8.4 Number of Unsolicited Retries: .............................................................................................. 27 1.9 Outstation Unsolicited Response Trigger Conditions....................................................................... 28 1.9.1 Number of class 1 events: ...................................................................................................... 28 1.9.2 Number of class 2 events: ...................................................................................................... 28 1.9.3 Number of class 3 events: ...................................................................................................... 28 1.9.4 Total number events from any class: ..................................................................................... 28 1.9.5 Hold time after class 1 event: ................................................................................................. 28 1.9.6 Hold time after class 2 event: ................................................................................................. 28 1.9.7 Hold time after class 3 event: ................................................................................................. 28 1.9.8 Hold time after event assigned to any class: .......................................................................... 29 1.9.9 Retrigger Hold Timer: ............................................................................................................ 29 1.9.10 Other Unsolicited Response Trigger Conditions:................................................................... 29 1.10 Outstation Performance ............................................................................................................... 30 1.10.1 Maximum Time Base Drift (milliseconds per minute): ......................................................... 30 1.10.2 When does outstation set IIN1.4?........................................................................................... 30 1.10.3 Maximum Internal Time Reference Error when set via DNP (ms):....................................... 30 1.10.4 Maximum Delay Measurement error (ms): ............................................................................ 30 1.10.5 Maximum Response time (ms): ............................................................................................. 30 DNP3 Device Profile Document Vendor Name: NOJA Power® Switchgear Device Name: RC10 Controller

NOJA-522-06

Page 4 09-01-2014

NOJA-522-06 1.10.6 1.10.7 1.10.8

Maximum time from start-up to IIN 1.4 assertion (ms): ........................................................ 31 Maximum Event Time-tag error for local Binary and Double-bit I/O (ms):.......................... 31 Maximum Event Time-tag error for local I/O other than Binary and Double-bit data types (ms): 31 1.11 Individual Field Outstation Parameters: ...................................................................................... 32 1.11.1 -assigned location name or code string (same as g0v245): ............................................. 32 1.11.2 -assigned ID Code/number string (same as g0v246): ..................................................... 32 1.11.3 -assigned name string for the outstation (same as g0v247): ........................................... 32 1.11.4 Device Serial Number string (same as g0v248): .................................................................... 32 1.12 SECURITY PARAMETERS ...................................................................................................... 33 1.12.1 DNP3 device for secure authentication ..................................................................... 33 2 MAPPING TO IEC 61850 OBJECT MODELS............................................................................... 34 3 CAPABILITIES AND CURRENT SETTINGS FOR DEVICE DATABASE (OUTSTATION ONLY) 35 3.1 Single-Bit Binary Inputs ................................................................................................................... 36 3.1.1 Static Variation reported when variation 0 requested: ........................................................... 36 3.1.2 Event Variation reported when variation 0 requested: ........................................................... 36 3.1.3 Event reporting mode: ............................................................................................................ 36 3.1.4 Binary Inputs included in Class 0 response:........................................................................... 36 3.2 Double-bit Input Points..................................................................................................................... 37 3.3 Binary Output Status and Control Relay Output Block .................................................................... 38 3.3.1 Minimum pulse time allowed with Trip, Close, and Pulse On commands: ........................... 38 3.3.2 Maximum pulse time allowed with Trip, Close, and Pulse On commands: .......................... 38 3.3.3 Binary Output Status included in Class 0 response: ............................................................... 38 3.3.4 Reports Output Command Event Objects: ............................................................................. 38 3.3.5 Static Variation reported when variation 0 requested: ........................................................... 38 3.3.6 Event Variation reported when variation 0 requested: ........................................................... 38 3.3.7 Command Event Variation reported when variation 0 requested: ......................................... 38 3.3.8 Event reporting mode: ............................................................................................................ 39 3.3.9 Command Event reporting mode: .......................................................................................... 39 3.3.10 Maximum Time between Select and Operate: ....................................................................... 39 3.4 Counters/Frozen Counters ................................................................................................................ 40 3.4.1 Static Counter Variation reported when variation 0 requested: ............................................. 40 3.4.2 Counter Event Variation reported when variation 0 requested: ............................................. 40 3.4.3 Counters included in Class 0 response: .................................................................................. 40 3.4.4 Counter Event reporting mode: .............................................................................................. 40 3.4.5 Static Frozen Counter Variation reported when variation 0 requested: ................................. 41 3.4.6 Frozen Counter Event Variation reported when variation 0 requested: ................................. 41 3.4.7 Frozen Counters included in Class 0 response: ...................................................................... 41 3.4.8 Frozen Counter Event reporting mode: .................................................................................. 41 3.4.9 Counters Roll Over at:............................................................................................................ 41 3.4.10 Counters frozen by means of:................................................................................................. 42 3.5 Anaput Points .......................................................................................................................... 43 3.5.1 Static Variation reported when variation 0 requested: ........................................................... 43 3.5.2 Event Variation reported when variation 0 requested: ........................................................... 43 3.5.3 Event reporting mode: ............................................................................................................ 43 3.5.4 Anaputs Included in Class 0 response: ......................................................................... 44 3.5.5 How Deadbands are set: ......................................................................................................... 44 3.5.6 Analog Deadband Algorithm: ................................................................................................ 44 3.5.7 Static Frozen Anaput Variation reported when variation 0 requested: ......................... 44 DNP3 Device Profile Document Vendor Name: NOJA Power® Switchgear Device Name: RC10 Controller

NOJA-522-06

Page 5 09-01-2014

NOJA-522-06 3.5.8 Frozen Anaput Event Variation reported when variation 0 requested: ......................... 45 3.5.9 Frozen Anaputs included in Class 0 response:.............................................................. 45 3.5.10 Frozen Anaput Event reporting mode: .......................................................................... 45 3.6 Analog Output Status and Analog Output Control Block ................................................................ 46 Not ed ........................................................................................................................................ 46 3.7 Sequential File Transfer .................................................................................................................... 47 3.7.1 File Transfer ed:......................................................................................................... 47 3.8 Octet String Points ............................................................................................................................ 48 3.8.1 Event reporting mode: ............................................................................................................ 48 3.8.2 Octet Strings Included in Class 0 response: ........................................................................... 48 3.9 Virtual Terminal Port Numbers (Points) .......................................................................................... 49 3.10 Data Set Prototype ....................................................................................................................... 50 3.11 Data Set Descriptor Contents and Characteristics ....................................................................... 51 3.12 Data Set Descriptor – Point Index Attributes .............................................................................. 52 4 IMPLEMENTATION TABLE ......................................................................................................... 53 5 DATA POINTS LIST (OUTSTATION ONLY) .............................................................................. 61 5.1 Definition of Binary Input Point List:............................................................................................... 62 5.2 Definition of Double-bit Input Point List: ........................................................................................ 74 5.3 Definition of Binary Output Status/Control relay output block (CROB) Point List: ....................... 75 5.4 Definition of Counter/Frozen Counter Point List: ............................................................................ 79 5.5 Definition of Anaput Point List: .............................................................................................. 84 5.6 Definition of Analog Output Status/Analog Output Control Block Point List: ................................ 91 5.7 Definition of File Names that may be read or written: ..................................................................... 92 5.8 Definition of Octet String Point List: ............................................................................................... 93 5.9 Definition of Virtual Terminal Port Numbers: ................................................................................. 94 5.10 Definition of Data Set Prototypes:............................................................................................... 95 5.11 Definition of Data Set Descriptors: ............................................................................................. 96 5.12 Data Set Descriptor – Point Index Attributes .............................................................................. 97 6 Internal Indications ........................................................................................................................... 98 7 Buffer Size ........................................................................................................................................ 99 8 DNP3 settings ................................................................................................................................. 100 8.1 Static and Event object default variations....................................................................................... 104 8.2 Dial Out Settings............................................................................................................................. 106


NOJA-522-06

Page 6 09-01-2014

NOJA-522-06

1 Introduction This DNP3 protocol implementation is fully compliant with DNP3 Subset Definition Level 2, contains many Subset Level 3 features and contains some functionality beyond Subset Level 3. Functionality included in this implementation is based on the Triangle MicroWorks, Inc. Slave Source Code Library except for the following objects: 

Short Floating Point Analog representation; Obj30, var5; Obj32, var5, var7; Obj34, var3; Obj40, var3; Obj41 var3



Long Floating Point Analog representation; Obj30, var6; Obj32, var6, var8; Obj40, var4; Obj41 var4



Analog Output Points Obj40, all variations; Obj41, all variations



Sequential File Transfer Obj 70, all variations



Virtual Terminal Objects Obj 112, Obj 113

Applicability This manual describes the DNP3 Protocol Implementation for RC10 software versions from 1.8.y.0 onwards. If you have a software version earlier than this then this document does not apply. Please your NOJA Power representative for further information. The software version can be read from the RC10 LCD screen by navigating to the Identification screen as described in the recloser manual. Connection Management The RC10 DNP3 interface is intended for use with a single DNP3 master station with a single set of event buffers interfaced through a single communications port (either serial or Ethernet). In general, it is recommended that it is only used in this manner. If a is intending to use redundant paths or multiple master stations please refer to NOJA-565-01 RC10 SCADA Interface Description for considerations and limitations. In particular the should note: 

Operation over redundant paths is dependent on the master station’s capabilities.



There is no configuration that permits “normal” DNP3 event polling operation to be performed concurrently from more than one master station or control centre without errors.



A restricted subset of DNP3 operations with multiple different master stations is possible, but care must be taken to ensure that event reporting functions are either not used, or are only


NOJA-522-06

Page 7 09-01-2014

NOJA-522-06 used very selectively. This is not “normal” DNP3 usage and may require specific configuration settings to be made in both the masters and in the RC10 in order to avoid errors. 

A very high level of understanding of the modes of operation of DNP3 may be required in order to correctly configure a multi-master system in such a manner as to avoid errors.


NOJA-522-06

Page 8 09-01-2014

NOJA-522-06 1.1

DEVICE IDENTIFICATION

1.1.1

Device Function:

Capabilities

If configurable, list methods

Outstation

Masters send DNP requests, while Outstations send DNP responses. If a single physical device can perform both functions, a separate Device Profile Document must be provided for each function.

1.1.2

Vendor Name:

The name of the organization producing the device. Note: The current value of this outstation parameter is available remotely using protocol object Group 0 Variation 252.

1.1.3

Device Name:

The model and name of the device, sufficient to distinguish it from any other device from the same organization. Note: The current value of this outstation parameter is available remotely using protocol object Group 0 Variation 250.

1.1.4

Device manufacturer’s hardware version string:

Note: The current value of this outstation parameter is available remotely using protocol object Group 0 Variation 243.

1.1.5

Device manufacturer’s software version string:


DNP3 Device Profile Document Vendor Name:

NOJA Power® Switchgear

Device Name: RC10 Controller

NOJA-522-06

Page 9 09-01-2014

NOJA-522-06 1.1


1.1.6

Device Profile Document Version Number:

Capabilities


Version of the Device Profile Document is indicated by a whole number incremented with each new release. This should match the latest version shown in the Revision History at the beginning of this document.

1.1.7

DNP Levels ed for:

Indicate each DNP3 Level to which the device conforms fully. For Masters, requests and responses can be indicated independently.

Masters Only Requests Responses None Level 1 Level 2 Level 3 Level 4 Outstations Only Requests and Responses None Level 1 Level 2 Level 3 Level 4

1.1.8

ed Function Blocks:




Self-Address Data Sets File Transfer Virtual Terminal Mapping to IEC 61850 Object Models defined in a DNP3 XML file Function code 31, activate configuration Secure Authentication (if checked then see 1.12)

NOJA-522-06

Page 10 09-01-2014

NOJA-522-06 1.1


Capabilities


For static (non-change-event) object requests, request qualifier codes 00 and 01 (start-stop), 07 and A brief description intended to quickly 08 (limited quantity), and 17 and 28 (index) are identify for the reader the most obvious ed in addition to request qualifier code 06 (no features the device s in addition range – or all points). to the Highest DNP Level ed. The complete list of features is Static object requests received with qualifiers 00, 01, described in the Implementation Table. 06, 07, or 08, will be responded with qualifiers 00 or

1.1.9

Notable Additions:

01. Static object requests received with qualifiers 17 or 28 will be responded with qualifiers 17 or 28. For changeevent object requests, qualifiers 17 or 28 are always responded. 16-bit and 32-bit Analog Change Events with Time are ed. Anaput Deadbands, Object 34, variations 1 through 3, are ed.

1.1.10 Methods to set Configurable Parameters:

1.1.11 DNP3 XML files available On-Line:

XML – Loaded via DNP3 File Transfer XML – Loaded via other transport mechanism Terminal – ASCII Terminal Command Line Software – Vendor software named CMS Proprietary file loaded via DNP3 file transfer Proprietary file loaded via other transport mechanism Direct – Keypad on device front Factory – Specified when device is ordered Protocol – Set via DNP3 (e.g. assign class) Other – explain _______________________ No online XML File available.

XML configuration file names that can be read or written through DNP3 File Transfer to a device A device’s currently running configuration is returned by DNP3 online XML file read from the device. DNP3 on-line XML file write to a device will update the device’s configuration when the Activate Configuration (function code 31) is received.




NOJA-522-06

Page 11 09-01-2014

NOJA-522-06 1.1


1.1.12 External DNP3 XML files available Off-line:

Capabilities


No external XML file available.

XML configuration file names that can be read or written from an external system, typically from a system that maintains the outstation configuration. External off-line XML file read permits an XML definition of a new configuration to be supplied from offline configuration tools. External off-line XML file write permits an XML definition of a new configuration to be supplied to off-line configuration tools.

1.1.13 Connections ed:




Serial (complete section 1.2) IP Networking (complete section 1.3) Other, explain ________________________

NOJA-522-06

Page 12 09-01-2014

NOJA-522-06 1.2

SERIAL CONNECTIONS

1.2.1

Port Name

Name used to reference the communication port defined in this section.


Capabilities

Three USB ports and one RS232 port are available. RS232, USBA, USBC, USBC.

1.2.2

Serial Connection Parameters:

Asynchronous - 8 Data Bits, 1 Start Bit, 1 Stop Bit, No Parity Other, explain __________________________

1.2.3

Baud Rate:

Fixed at _______ Configurable, range 300 to 115,200 Configurable, selectable from ____,____,____ Configurable, other, describe_______________

1.2.4

Hardware Flow Control (Handshaking):

Describe hardware signaling requirements of the interface. Where a transmitter or receiver is inhibited until a given control signal is asserted, it is considered to require that signal prior to sending or receiving characters. Where a signal is asserted prior to transmitting, that signal will be maintained active until after the end of transmission. Where a signal is asserted to enable reception, any data sent to the device when the signal is not active could be discarded.

 None RS-232 / V.24 / V.28 Options: Asserts:  RTS before Tx  DTR before Tx  RTS before Rx  DTR before Rx  Always RTS  Always DTR

Both None and Hardware Handshaking methods ed. Push to Talk asserts RTS to key a radio transmitter.

Requires before Tx: CTS  Asserted  Deasserted DCD  Asserted  Deasserted DSR  Asserted  Deasserted RI  Asserted  Deasserted  Requires Rx inactive before Tx Requires before Rx: CTS  Asserted DCD  Asserted DSR  Asserted RI  Asserted

   

Deasserted Deasserted Deasserted Deasserted

Always ignores:  CTS  DCD  DSR  RI  Other: DCD can be set to Ignore or Block Tx for RS 232 only




NOJA-522-06

Page 13 09-01-2014

NOJA-522-06 1.2

SERIAL CONNECTIONS

1.2.5

Interval to Request Link Status:

Indicates how often to send Data Link Layer status requests on a serial connection. This parameter is separate from the T Keep-alive timer.

1.2.6

s DNP3 Collision Avoidance:

Indicates whether a device uses a collision avoidance algorithm. Collision avoidance may be implemented by a back-off timer with two parameters that define the back-off time range or by some other vendor-specific mechanism. The recommended back-off time is specified as being a fixed minimum delay plus a random delay, where the random delay has a maximum value specified. This defines a range of delay times that are randomly distributed between the minimum value and the minimum plus the maximum of the random value. If a back-off timer is implemented with only a fixed or only a random value, select the Back-off time method and set the parameter that is not ed to “Fixed at 0 ms”.




Capabilities


Not ed Fixed at_________ seconds Configurable, range _____ to ______ seconds Configurable, selectable from ___,___,___ seconds Configurable, other, describe ________________ No Yes, using Back-off time = (Min + Random) method Minimum Back-off time: Fixed at_________ ms Configurable, range _____ to ______ ms Configurable, selectable from __,___,___ms Configurable, other, describe________________ Maximum Random Back-off time component: Fixed at_________ ms Configurable, range _____ to ______ ms Configurable, selectable from ___,___,___ ms Configurable, other, describe________________ Other, explain ________________________

NOJA-522-06

Page 14 09-01-2014

NOJA-522-06 1.2

SERIAL CONNECTIONS

1.2.7

Receiver Inter-character Timeout:

When serial interfaces with asynchronous character framing are used, this parameter indicates if the receiver makes a check for gaps between characters (i.e. extension of the stop bit time of one character prior to the start bit of the following character within a message). If the receiver performs this check and the timeout is exceeded then the receiver discards the current data link frame. A receiver that does not discard data link frames on the basis of inter-character gaps is considered to not perform this check.

Capabilities


Not checked No gap permitted Fixed at _____ bit times Fixed at _____ ms Configurable, range ____ to ____ bit times Configurable, range ____ to ____ ms Configurable, Selectable from ___,___,___bit times Configurable, Selectable from ____, ____, ____ ms Configurable, other, describe __________________ Variable, explain ____

Where no asynchronous serial interface is fitted, this parameter is not applicable. In this case none of the options shall be selected.

1.2.8

Inter-character gaps in transmission:

When serial interfaces with asynchronous character framing are used, this parameter indicates whether extra delay is ever introduced between characters in the message, and if so, the maximum width of the gap.

None (always transmits with no inter-character gap) Maximum _____ bit times Maximum _____ ms

Where no asynchronous serial interface is fitted, this parameter is not applicable. In this case none of the options shall be selected.




NOJA-522-06

Page 15 09-01-2014

NOJA-522-06 1.3

IP NETWORKING

1.3.1

Port Name

Capabilities


Name used to reference the communication port defined in this section.

1.3.2

Type of End Point:

T Initiating (Master Only) T Listening (Outstation Only) T Dual (required for Masters) UDP Datagram (required)

When Unsolicited is ON, T Dual is active. When Unsolicited is OFF, T Listening is active. Configurable

1.3.3

IP Address of this Device:

1.3.4

Subnet Mask:

Configurable

1.3.5

Gateway IP Address:

Configurable

1.3.6

Accepts T Connections or UDP Datagrams from:

1.3.7

IP Address(es) from which T Connections or UDP Datagrams are accepted:

1.3.8

T Listen Port Number:

If Outstation or dual end point Master, port number on which to listen for incoming T connect requests. Required to be configurable for Masters and recommended to be configurable for Outstations.




Allows all (show as *.*.*.* in 1.3.7) Limits based on an IP address Limits based on list of IP addresses Limits based on a wildcard IP address Limits based on list of wildcard IP addresses Other validation, explain_________________ Configurable

Not Applicable (Master w/o dual end point) Fixed at 20,000 Configurable, range 1 to 65534 Configurable, selectable from ____,____,____ Configurable, other, describe________________

NOJA-522-06

Page 16 09-01-2014

NOJA-522-06 1.3

IP NETWORKING

1.3.9

T Listen Port Number of remote device:

If Master or dual end point Outstation, port number on remote device with which to initiate connection. Required to be configurable for Masters and recommended to be configurable for Outstations.

1.3.10 T Keep-alive timer: The time period for the keep-alive timer on active T connections.

1.3.11 Local UDP port: Local UDP port for sending and/or receiving UDP datagrams. Master may let system choose an available port. Outstation must use one that is known by the master.

Capabilities

Not Applicable (Outstation w/o dual end point) Fixed at 20,000 Configurable, range 1 to 65534 Configurable, selectable from ____,____,____ Configurable, other, describe_______________

Fixed at ___________ms Configurable, range 1 to 172800s Configurable, selectable from ____,____,____ms Configurable, other, describe_______________ Fixed at 20,000 Configurable, range 1 to 65534 Configurable, selectable from ____,____,____ Configurable, other, describe_______________ Let system choose (Master only)

1.3.12 Destination UDP port for DNP3 Requests (Master Only):

Fixed at 20,000 Configurable, range _______ to _______ Configurable, selectable from ____,____,____ Configurable, other, describe_______________

1.3.13 Destination UDP port for initial unsolicited null responses (UDP only Outstations):

None Fixed at 20,000 Configurable, range 1 to 65534 Configurable, selectable from ____,____,____ Configurable, other, describe_______________

For a UDP only Outstation, the destination UDP port for sending initial unsolicited Null response

1.3.14 Destination UDP port for responses: For a UDP only Outstation, the destination UDP port for sending all responses other than initial unsolicited Null Response.





Not Applicable

None Fixed at 20,000 Configurable, range 1 to 65534 Configurable, selectable from ____,____,____ Configurable, other, describe_______________ Use source port number

NOJA-522-06

Page 17 09-01-2014

NOJA-522-06 1.3

Capabilities

IP NETWORKING

1.3.15 Multiple outstation connections (Masters only):


s multiple outstations (Masters only)

Not Applicable

s multiple masters (Outstations only)

Not Applicable

Master only. Indicates whether multiple outstation connections are ed.

1.3.16 Multiple master connections (Outstations Only): Outstation only. Indicates whether multiple master connections are ed and the method that can be used to establish connections.

If ed, the following methods may be used: Method 1 (based on IP address) - required Method 2 (based on IP port number) recommended Method 3 (browsing for static data) - optional

1.3.17 Time synchronization :




DNP3 LAN procedure (function code 24) DNP3 Write Time (not recommended over LAN) Other, explain _________________________ Not ed

NOJA-522-06

Page 18 09-01-2014

NOJA-522-06 1.4

LINK LAYER

1.4.1

Data Link Address:

Indicates if the link address is configurable over the entire valid range of 0 to 65,519. Data link addresses 0xFFF0 through 0xFFFF are reserved for broadcast or other special purposes.

1.4.2

DNP3 Source Address Validation:

Indicates whether the device will filter out messages not from a specific source address.

1.4.3

DNP3 Source Address(es) expected when Validation is Enabled:

Selects the allowed source address(es).

1.4.4

Self Address using address 0xFFFC:

Capabilities


Fixed at______ Configurable, range 0 to 65519 Configurable, selectable from ____,____,____ Configurable, other, describe________________

Never Always, one address allowed (shown in 1.4.3) Always, any one of multiple addresses allowed (each selectable as shown in 1.4.3) Sometimes, explain________________

Configurable to any 16 bit DNP Data Link Address value Configurable, range _______ to _______ Configurable, selectable from ____,____,____ Configurable, other, describe________________

If “Validate Master Address” is enabled then only messages from the “Unsolicited Response Master Address” setting will be accepted. This setting is called the “Unsolicited Response Master Address” in the RC10 Controller.

Yes (only allowed if configurable) No

If an Outstation receives a message with a destination address of 0xFFFC it shall respond normally with its own source address. It must be possible to disable the feature if ed.

1.4.5

Sends Confirmed Data Frames:

A list of conditions under which the device transmits confirmed link layer services (TEST_LINK_STATES, RESET_LINK_STATES, CONFIRMED__DATA).




Always Sometimes, only for multi-frame messages Never

NOJA-522-06

Page 19 09-01-2014

NOJA-522-06 1.4

LINK LAYER

1.4.6

Data Link Layer Confirmation Timeout:

This timeout applies to any secondary data link message that requires a confirm or response (link reset, link status, data, etc)

1.4.7

Maximum Data Link Retries:

The number of times the device will retransmit a frame that requests Link Layer confirmation.

1.4.8

Maximum number of octets Transmitted in a Data Link Frame:

This number includes the CRCs. With a length field of 255, the maximum size would be 292.

1.4.9

Maximum number of octets that can be Received in a Data Link Frame:

Capabilities


None Fixed at______ ms Configurable, range 0 to 60s Configurable, selectable from ___,___,___ms Configurable, other, describe________________ Variable, explain _______________________ Never Retries Fixed at ___________ Configurable, range 0 to 32767 Configurable, selectable from ____,____,____ Configurable, other, describe______________ Fixed at 292 Configurable, range 64 to 292 Configurable, selectable from ____,____,____ Configurable, other, describe________________

Fixed at 292 Configurable, range ________ to _______ Configurable, selectable from ____,____,____ Configurable, other, describe_______________

This number includes the CRCs. With a length field of 255, the maximum size would be 292. The device must be able to receive 292 octets to be compliant.




NOJA-522-06

Page 20 09-01-2014

NOJA-522-06 1.5

APPLICATION LAYER

Capabilities

1.5.1

Maximum number of octets Transmitted in an Application Layer Fragment other than File Transfer:



This size does not include any transport or frame octets.  Masters must provide a setting less

than or equal to 249.

 Outstations must provide a setting

less than or equal to 2048. Note: The current value of this outstation parameter is available remotely using protocol object Group 0 Variation 240.

1.5.2

Maximum number of octets Transmitted in an Application Layer Fragment containing File Transfer:

Fixed at ___________ Configurable, range ________ to _______ Configurable, selectable from ____,____,____ Configurable, other, describe_______________

1.5.3

Maximum number of octets that can be Received in an Application Layer Fragment:


Not Applicable

This size does not include any transport or frame octets.  Masters must provide a setting

greater than or equal to 2048.

 Outstations must provide a setting

greater than or equal to 249.





NOJA-522-06

Page 21 09-01-2014

NOJA-522-06 1.5

APPLICATION LAYER

1.5.4

Timeout waiting for Complete Application Layer Fragment:

Timeout if all frames of a message fragment are not received in the specified time. Measured from time first frame of a fragment is received until the last frame is received.

1.5.5

Maximum number of objects allowed in a single control request for CROB (group 12):


Capabilities None Fixed at______ ms Configurable, range _______ to _______ms Configurable, selectable from ___,___,___ms Configurable, other, describe________________ Variable, explain _______________________

Fixed at10 Configurable, range ________ to _______ Configurable, selectable from ____,____,____ Configurable, other, describe_______________ Variable, explain _______________________

1.5.6

Maximum number of objects allowed in a single control request for Analog Outputs (group 41):

Fixed at 0 Configurable, range ________ to _______ Configurable, selectable from ____,____,____ Configurable, other, describe_______________ Variable, explain _______________________

1.5.7

Maximum number of objects allowed in a single control request for Data Sets (groups 85,86,87):

Fixed at 0 Configurable, range ________ to _______ Configurable, selectable from ____,____,____ Configurable, other, describe_______________ Variable, explain _______________________

1.5.8

s mixing object groups (AOBs, CROBs and Data Sets) in the same control request:

Not applicable – only CROB ed Yes No





NOJA-522-06

Page 22 09-01-2014

NOJA-522-06 1.6

FILL OUT THE FOLLOWING ITEMS FOR MASTERS ONLY

Capabilities


Not Applicable




NOJA-522-06

Page 23 09-01-2014

NOJA-522-06 1.7

FILL OUT THE FOLLOWING ITEMS FOR OUTSTATIONS ONLY

Capabilities

1.7.1

Timeout waiting for Application Confirm of solicited response message:

None Fixed at______ ms Configurable, range 0 to 3600s Configurable, selectable from ___,___,___ms Configurable, other, describe________________ Variable, explain _______________________

1.7.2

How often is time synchronization required from the master?

Never needs time Within 1 second after IIN1.4 is set Periodically, fixed at _______ seconds Periodically, between ___ and ___ seconds

Details of when the master needs to perform a time synchronization to ensure that the outstation clock does not drift outside of an acceptable tolerance. If the option to relate this to IIN1.4 is used then details of when IIN1.4 is asserted are in section 1.10.2.

1.7.3

Device Trouble Bit IIN1.6:

If IIN1.6 device trouble bit is set under certain conditions, explain the possible causes.

1.7.4

File Handle Timeout:

If there is no activity referencing a file handle for a configurable length of time, the outstation must do an automatic close on the file. The timeout value must be configurable up to 1 hour. When this condition occurs the outstation will send a File Transport Status Object (group 70 var 6) using a status code value of file handle expired (0x02).

1.7.5

Event Buffer Overflow Behavior:





Never used Reason for setting - Set if a device malfunction is detected refer to ‘Malfunctions’ section of Binary Inputs and/or the manual for a description of possible causes. Not applicable, files not ed Fixed at______ ms Configurable, range _______ to _______ms Configurable, selectable from ___,___,___ms Configurable, other, describe________________ Variable, explain _______________________

Discard the oldest event Discard the newest event Other, explain _________________________

NOJA-522-06

Page 24 09-01-2014

NOJA-522-06 1.7

1.7.6

FILL OUT THE FOLLOWING ITEMS FOR OUTSTATIONS ONLY Event Buffer Organization:

Explain how event buffers are arranged (per Object Group, per Class, single buffer, etc,) and provide their sizes

1.7.7

Capabilities

Object 2 (binary) Object 22 (counters) Object 23 (frozen counters) Object 32 (Analog)

Sends Multi-Fragment Responses:


- 500 events; - 400 events; - 350 events; - 350 events.

Yes No

Indicates whether an Outstation sends multi-fragment responses (Masters do not send multi-fragment requests).

1.7.8

Last Fragment Confirmation:

Indicates whether the Outstation requests confirmation of the last fragment of a multi-fragment response.

1.7.9

DNP Command Settings preserved through a device reset:

If data associated with any of these requests are written through the DNP protocol but not preserved through a restart of the Outstation, the Master will have to write them again anytime the Restart IIN bit is set




When “Always” is selected for Link Layer “Confirmation Mode”

Always Sometimes, Never

Assign Class Analog Deadbands Data Set Prototypes Data Set Descriptors Function Code 31 Activate Configuration

NOJA-522-06

Page 25 09-01-2014

NOJA-522-06 1.8

1.8.1

OUTSTATION UNSOLICITED RESPONSE s Unsolicited Reporting:

Capabilities


Not ed Configurable, selectable from On and Off

When the unsolicited response mode is configured “off”, the device is to behave exactly like an equivalent device that has no for unsolicited responses. If set to On, the Outstation will send a null Unsolicited Response after it restarts, then wait for an Enable Unsolicited Response command from the master before sending additional Unsolicited Responses containing event data.

1.8.2

Master Data Link Address:

The destination address of the master device where the unsolicited responses will be sent.

1.8.3

Unsolicited Response Confirmation Timeout:

This is the amount of time that the outstation will wait for an Application Layer confirmation back from the master indicating that the master received the unsolicited response message. As a minimum, the range of configurable values must include times from one second to one minute. This parameter may be the same one that is used for normal, solicited, application confirmation timeouts, or it may be a separate parameter.




Fixed at______ Configurable, range 0 to 65534 Configurable, selectable from ____,____,____ Configurable, other, describe________________

Fixed at______ ms Configurable, range 0 to 86400s Configurable, selectable from ___,___,___ms Configurable, other, describe________________ Variable, explain _______________________

NOJA-522-06

Page 26 09-01-2014

NOJA-522-06 1.8

1.8.4

OUTSTATION UNSOLICITED RESPONSE Number of Unsolicited Retries:

This is the number of retries that an outstation transmits in each unsolicited response series if it does not receive confirmation back from the master. The configured value includes identical and regenerated retry messages. One of the choices must provide for an indefinite (and potentially infinite) number of transmissions.




Capabilities


None Fixed at ___________ Configurable, range 0 to 255 Configurable, selectable from ____,____,____ Configurable, other, describe______________ Always infinite, never gives up

NOJA-522-06

Page 27 09-01-2014

NOJA-522-06 1.9

OUTSTATION UNSOLICITED RESPONSE TRIGGER CONDITIONS

Capabilities

1.9.1

Number of class 1 events:

Class 1 not used to trigger Unsolicited Responses Fixed at ___________ Configurable, range 1 to 255 Configurable, selectable from ____,____,____ Configurable, other, describe______________

1.9.2



1.9.3



1.9.4

Total number events from any class:

Total Number of Events not used to trigger Unsolicited Responses Fixed at ___________ Configurable, range ________ to _______ Configurable, selectable from ____,____,____ Configurable, other, describe______________

1.9.5

Hold time after class 1 event:

Class 1 not used to trigger Unsolicited Responses Fixed at ___________ ms Configurable, range 0 to 86400s Configurable, selectable from ____,____,____ ms Configurable, other, describe______________

A configured value of 0 indicates that responses are not delayed due to this parameter.

1.9.6



1.9.7







Class 2 not used to trigger Unsolicited Responses Fixed at ___________ ms Configurable, range 0 to 86400s Configurable, selectable from ____,____,____ ms Configurable, other, describe______________ Class 3 not used to trigger Unsolicited Responses Fixed at ___________ ms Configurable, range 0 to 86400s Configurable, selectable from ____,____,____ ms Configurable, other, describe______________

NOJA-522-06

Page 28 09-01-2014

NOJA-522-06 1.9

1.9.8

OUTSTATION UNSOLICITED RESPONSE TRIGGER CONDITIONS

Capabilities

Hold time after event assigned to any class:

Class events not used to trigger Unsolicited Responses Fixed at ___________ ms Configurable, range ________ to _______ ms Configurable, selectable from ____,____,____ ms Configurable, other, describe______________


1.9.9

Retrigger Hold Timer:

Hold-time timer will be retriggered for each new event detected (may get more changes in next response) Hold-time timer will not be retriggered for each new event detected (guaranteed update time)

The hold-time timer may be retriggered for each new event detected (increased possibly of capturing all the changes in a single response) or not retriggered (giving the master a guaranteed update time).

1.9.10 Other Unsolicited Response Trigger Conditions:

_________________________________________ _________________________________________ _________________________________________





NOJA-522-06

Page 29 09-01-2014

NOJA-522-06 1.10

OUTSTATION PERFORMANCE

1.10.1 Maximum Time Base Drift (milliseconds per minute): If the protocol is synchronized by DNP, what is the clock drift rate over the full operating temperature range.

1.10.2 When does outstation set IIN1.4? When does the outstation set the internal indication NEED_TIME.

1.10.3 Maximum Internal Time Reference Error when set via DNP (ms): The difference between the time set in a DNP Write Time message, and the time actually set in the Outstation.

1.10.4 Maximum Delay Measurement error (ms): The difference between the time reported in the delay measurement response and the actual time between receipt of the delay measurement request and issuing the delay measurement reply.

1.10.5 Maximum Response time (ms): The amount of time an Outstation will take to respond upon receipt of a valid request. This does not include the message transmission time.




Capabilities


Fixed at 3.5 ms Range 0 to 12 ms Selectable from ____,____,____ ms Other, describe______________

Never Asserted at startup until first Time Synchronization request received Periodically, range 0 to 69120 minutes Periodically, selectable from ____,____,___ seconds Range 0 to 69120 minutes after last time sync Selectable from___,___,___ seconds after last time sync When time error may have driftedby range ____to____ ms When time error may have drifted by selectable from ____,____,___

1) ed Range for “Need Time”,

Fixed at 1000 ms Range ________ to _______ ms Selectable from ____,____,____ ms Other, describe______________

Rounded down to nearest second.

0-69120min. 2) If “Need Time” set to zero then IIN 1.4 is not set.



NOJA-522-06

Page 30 09-01-2014

NOJA-522-06 1.10

OUTSTATION PERFORMANCE

Capabilities

1.10.6 Maximum time from startup to IIN 1.4 assertion (ms):


1.10.7 Maximum Event Time-tag error for local Binary and Double-bit I/O (ms):


The error between the time-tag reported and the absolute time of the physical event. This error includes the Internal Time Reference Error.


Note: The current value of this parameter is available remotely using protocol object Group 0 Variation 217.

1.10.8 Maximum Event Time-tag error for local I/O other than Binary and Doublebit data types (ms):





NOJA-522-06

Page 31 09-01-2014

NOJA-522-06 1.11

INDIVIDUAL FIELD OUTSTATION PARAMETERS:

Value of Current Setting


1.11.1 -assigned location name or code string (same as g0v245): 1.11.2 -assigned ID Code/number string (same as g0v246): 1.11.3 -assigned name string for the outstation (same as g0v247): 1.11.4 Device Serial Number string (same as g0v248):




NOJA-522-06

Page 32 09-01-2014

NOJA-522-06 1.12

SECURITY PARAMETERS

Capabilities

1.12.1 DNP3 device for secure authentication The for secure authentication is optional in DNP3 devices. Indicate here if the device s secure authentication.


Secure Authentication not ed If Secure Authentication is ed, what Version(s) are ed:

If the device does not secure authentication then ignore the rest of this section.

Fixed at ___________ Configurable, selectable from ____,____,____

If the device does secure authentication then specify the version(s) that are ed in the device. The version number is an integer value defined in the protocol document “DNP3Spec-V2-Sup1SecureAuthentication”. The volume 2 supplement shows version numbers of all associated documents that comprise that version of Secure Authentication.




NOJA-522-06

Page 33 09-01-2014

NOJA-522-06

2 MAPPING TO IEC 61850 OBJECT MODELS This optional section allows each configuration parameter or point in the DNP Data map to be tied to an attribute in the 61850 object models. The 61850 mappings are stored in the XML version of the Device Profile Document as a list of XPath references to the tags representing real-time data from DNP under each data point (for example value, timestamp, and quality for Anaputs) paired with an IEC 61850 Object Reference in the form of a flattened ACSI (Abstract Communication Service Interface) name of the object and attributes as specified in IEC 61850 parts 7-4 and 7-3. The XPath reference into the DNP XML file may also contain a reference to a constant value, a formula or conditional expression involving one or more XML tags, or a reference to a configuration parameter that is not associated with a particular data point. A graphical or table representation may be generated from the XML and shown here in the printed version of the Device Profile Document to give an idea of the Logical Devices, Logical Notes, and Attributes available via the DNP interface. The following is an example table format:

IEC 61850 Object

DNP3 XPATH Reference

Comments

This section is not applicable.




NOJA-522-06

Page 34 09-01-2014

NOJA-522-06

3 CAPABILITIES AND CURRENT SETTINGS FOR DEVICE DATABASE (OUTSTATION ONLY) The following tables identify the capabilities and current settings for each DNP3 data type. Details defining the data points available in the device are shown in part 5 of this Device Profile.




NOJA-522-06

Page 35 09-01-2014

NOJA-522-06 3.1

SINGLE-BIT BINARY INPUTS Capabilities

Static (Steady-State) Group Number: 1 Event Group Number: 2

3.1.1

Static Variation reported when variation 0 requested:

Variation 1 – Single-bit Packed format Variation 2 – Single-bit with flag Based on point Index

3.1.2

Event Variation reported when variation 0 requested:

Variation 1 – without time Variation 2 – with absolute time Variation 3 – with relative time Based on point Index

Note: The for binary input events can be determined remotely using protocol object Group 0 Variation 237.

3.1.3

Event reporting mode:

When responding with event data and more than one event has occurred for a data point, an Outstation may include all events or only the most recent event. All events are typically reported for Binary Inputs.

3.1.4

Binary Inputs included in Class 0 response:

If Binary Inputs are not included in the Class 0 response, Binary Input Events (group 2) may not be reported.





Only most recent All events

Always Never Only if point is assigned to Class 1, 2, or 3 Based on point Index (add column to table in part 5)

NOJA-522-06

Page 36 09-01-2014

NOJA-522-06 3.2

DOUBLE-BIT INPUT POINTS


Capabilities


Double-Bit Input Points not ed




NOJA-522-06

Page 37 09-01-2014

NOJA-522-06 3.3

BINARY OUTPUT STATUS AND CONTROL RELAY OUTPUT BLOCK

Binary Output Status Group Number: 10 Binary Output Event Group Number: 11 CROB Group Number: 12 Binary Output Command Event Object Num: 13

Capabilities

3.3.1

Minimum pulse time allowed with Trip, Close, and Pulse On commands:

Fixed at 0 ms (hardware may limit this further) Based on point Index (add column to table in part 5)

3.3.2

Maximum pulse time allowed with Trip, Close, and Pulse On commands:

Fixed at 4,294,967,295 ms (hardware may limit this further) Based on point Index (add column to table in part 5)

3.3.3

Binary Output Status included in Class 0 response:


If Binary Output Status points are not included in the Class 0 response, Binary Output Status Events (group 11) may not be reported.


3.3.4

Reports Output Command Event Objects:

Never Only upon a successful Control Upon all control attempts

3.3.5


Variation 1 – Continuous control Variation 2 – Continuous control, binary output status Based on point Index

3.3.6


Variation 1 – without time Variation 2 – with absolute time Based on point Index

Not ed

Variation 1 – without time Variation 2 – with absolute time Based on point Index (add column to table in part 5)

Not ed

Note: The for binary output events can be determined remotely using protocol object Group 0 Variation 222.

3.3.7

Command Event Variation reported when variation 0 requested:




NOJA-522-06

Page 38 09-01-2014

NOJA-522-06 3.3.8


When responding with event data and more than one event has occurred for a data point, an Outstation may include all events or only the most recent event.

3.3.9

Command Event reporting mode:


Not ed


Not ed


3.3.10 Maximum Time between Select and Operate:




Not Applicable Fixed at _____ seconds Configurable, range 0 to 3600 seconds Configurable, selectable from___,___,___ seconds Configurable, other, describe________________ Variable, explain _______________________ Based on point Index (add column to table in part 5)

NOJA-522-06

Page 39 09-01-2014

NOJA-522-06 3.4

COUNTERS/FROZEN COUNTERS

Static Counter Group Number: 20 Static Frozen Counter Group Number: 21 Counter Event Group Number: 22 Frozen Counter Event Group Number: 23

Capabilities

3.4.1

Static Counter Variation reported when variation 0 requested:

Variation 1 – 32-bit with flag Variation 2 – 16-bit with flag Variation 5 – 32-bit without flag Variation 6 – 16-bit without flag Based on point Index

3.4.2

Counter Event Variation reported when variation 0 requested:

Variation 1 – 32-bit with flag Variation 2 – 16-bit with flag Variation 5 – 32-bit with flag and time Variation 6 – 16-bit with flag and time Based on point Index

Note: The for counter events can be determined remotely using protocol object Group 0 Variation 227.

3.4.3

Counters included in Class 0 response:

If Counters are not included in the Class 0 response, Counter Events (group 22) may not be reported.

3.4.4

Counter Event reporting mode:

When responding with event data and more than one event has occurred for a data point, an Outstation may include all events or only the most recent event. Only the most recent event is typically reported for Counters. When reporting “only most recent”, the counter value reported in the response may be the value at the time of the original event or it may be the value at the time of the response.





Always Never Only if point is assigned to Class 1, 2, or 3 Based on point Index

A: Only most recent (value at time of event) B: Only most recent (value at time of response) C: All events Based on point Index (add column to table in part 5)

NOJA-522-06

Page 40 09-01-2014

NOJA-522-06 3.4



Capabilities

3.4.5

Static Frozen Counter Variation reported when variation 0 requested:

Variation 1 – 32-bit with flag Variation 2 – 16-bit with flag Variation 5 – 32-bit with flag and time Variation 6 – 16-bit with flag and time Variation 9 – 32-bit without flag Variation 10 – 16-bit without flag Based on point Index

3.4.6

Frozen Counter Event Variation reported when variation 0 requested:

Variation 1 – 32-bit with flag Variation 2 – 16-bit with flag Variation 5 – 32-bit with flag and time Variation 6 – 16-bit with flag and time Based on point Index

Note: The for frozen counter events can be determined remotely using protocol object Group 0 Variation 225.

3.4.7

Frozen Counters included in Class 0 response:

If Frozen Counters are not included in the Class 0 response, Frozen Counter Events (group 23) may not be reported.

3.4.8

Frozen Counter Event reporting mode:

When responding with event data and more than one event has occurred for a data point, an Outstation may include all events or only the most recent event. All events are typically reported for Frozen Counters.

3.4.9

Counters Roll Over at:





Always Never Only if point is assigned to Class 1, 2, or 3 Based on point Index

A: Only most recent frozen value B: All frozen values Based on point Index

16 Bits (65,535) 32 Bits (4,294,967,295) Other Fixed Value _________ Configurable; range _________ to__________ Configurable, selectable from ___,___,___ Configurable, other, describe________________ Based on point Index (add column to table in part 5)

NOJA-522-06

Page 41 09-01-2014

NOJA-522-06 3.4



3.4.10 Counters frozen by means of:




Capabilities


Master Request Freezes itself without concern for time of day Freezes itself and requires time of day Other, explain _____________________________

NOJA-522-06

Page 42 09-01-2014

NOJA-522-06 3.5

ANAPUT POINTS

Static (Steady-State) Group Number: 30 Static Frozen Group Number: 31 Event Group Number: 32 Frozen Anaput Event Group Number: 33 Deadband Group Number: 34

Capabilities

3.5.1


Variation 1 – 32-bit with flag Variation 2 – 16-bit with flag Variation 3 – 32-bit without flag Variation 4 – 16-bit without flag Variation 5 – single-precision floating point with flag Variation 6 – double-precision floating point with flag Based on point Index (add column to table in part 5)

3.5.2


Variation 1 – 32-bit without time Variation 2 – 16-bit without time Variation 3 – 32-bit with time Variation 4 – 16-bit with time Variation 5 – single-precision floating point w/o time Variation 6 – double-precision floating point w/o time Variation 7 – single-precision floating point with time Variation 8 – double-precision floating point with time Based on point Index (add column to table in part 5)

Note: The for anaput events can be determined remotely using protocol object Group 0 Variation 231.

3.5.3


When responding with event data and more than one event has occurred for a data point, an Outstation may include all events or only the most recent event. Only the most recent event is typically reported for Anaputs. When reporting “only most recent”, the analog value reported in the response may be the value at the time of the original event or it may be the value at the time of the response.





A: Only most recent (value at time of event) B: Only most recent (value at time of response) C: All events Based on point Index (add column to table in part 5)

NOJA-522-06

Page 43 09-01-2014

NOJA-522-06 3.5

ANAPUT POINTS


3.5.4

Anaputs Included in Class 0 response:

If Anaputs are not included in the Class 0 response, Anaput Events (group 32) may not be reported.

Capabilities


3.5.5

How Deadbands are set:

A. Global Fixed B. Configurable through DNP C. Configurable via other means D. Other, explain _____________________________ Based on point Index - column in part 5 specifies which of the options applies, B, C, or D

3.5.6

Analog Deadband Algorithm:

Simple Integrating Other, explain _____________________________ Based on point Index (add column to table in part 5)

simple -

just compares the difference from the previous reported value

integrating - keeps track of the accumulated change other -

3.5.7


Using CMS or (SCADA)

indicating another algorithm

Static Frozen Anaput Variation reported when variation 0 requested:




Variation 1 – 32-bit with flag Variation 2 – 16-bit with flag Variation 3 – 32-bit with time-of-freeze Variation 4 – 16-bit with time-of-freeze Variation 5 – 32-bit without flag Variation 6 – 16-bit without flag Variation 7 – Single-precision, floating-point with flag Variation 8 – Double-precision, floating-point with flag Based on point Index (add column to table in part 5)

NOJA-522-06

Not ed

Page 44 09-01-2014

NOJA-522-06 3.5

ANAPUT POINTS


3.5.8

Frozen Anaput Event Variation reported when variation 0 requested:

Note: The for frozen anaput events can be determined remotely using protocol object Group 0 Variation 230.

3.5.9

Frozen Anaputs included in Class 0 response:

If Frozen Anaputs are not included in the Class 0 response, Frozen Anaput Events (group 33) may not be reported.

3.5.10 Frozen Anaput Event reporting mode: When responding with event data and more than one event has occurred for a data point, an Outstation may include all events or only the most recent event. All events are typically reported for Frozen Anaputs.




Capabilities

Variation 1 – 32-bit without time Variation 2 – 16-bit without time Variation 3 – 32-bit with time Variation 4 – 16-bit with time Variation 5 – Single-precision, floating-point without time Variation 6 – Double-precision, floating-point without time Variation 7 – Single-precision, floating-point with time Variation 8 – Double-precision, floating-point with time Based on point Index (add column to table in part 5) Always Never Only if point is assigned to Class 1, 2, or 3 Based on point Index (add column to table in part 5)

A: Only most recent frozen value B: All frozen values Based on point Index (add column to table in part 5)

NOJA-522-06


Not ed

Not ed

Not ed

Page 45 09-01-2014

NOJA-522-06 3.6

ANALOG OUTPUT STATUS AND ANALOG OUTPUT CONTROL BLOCK

Analog Output Status Group Number: 40 Analog Output Control Block Group Number: 41 Analog Output Event Group Number: 42 Analog Output Command Event Group Number: 43

Capabilities


Not ed




NOJA-522-06

Page 46 09-01-2014

NOJA-522-06 3.7

SEQUENTIAL FILE TRANSFER

Capabilities

Group Number: 70

3.7.1

File Transfer ed:





Yes No (do not complete any further entries in section 3.7)

NOJA-522-06

Page 47 09-01-2014

NOJA-522-06 3.8

OCTET STRING POINTS


3.8.1



3.8.2

Octet Strings Included in Class 0 response:

If Octet Strings are not included in the Class 0 response, Octet String Events (group 111) may not be reported.




Capabilities




NOJA-522-06

Page 48 09-01-2014

NOJA-522-06 3.9

VIRTUAL TERMINAL PORT NUMBERS (POINTS)


Capabilities


This version of the Device Profile document has no requirement for describing Virtual Terminal point capabilities and current settings. This page is intentionally left blank, existing as a placeholder for future use.




NOJA-522-06

Page 49 09-01-2014

NOJA-522-06 3.10

DATA SET PROTOTYPE

Group Number: 85 Variation Number: 1

Capabilities


This version of the Device Profile document has no requirement for describing Data Set Prototype capabilities and current settings. This page is intentionally left blank, existing as a placeholder for future use.




NOJA-522-06

Page 50 09-01-2014

NOJA-522-06 3.11

DATA SET DESCRIPTOR CONTENTS AND CHARACTERISTICS

Capabilities



This version of the Device Profile document has no requirement for describing Data Set Descriptor capabilities and current settings. This page is intentionally left blank, existing as a placeholder for future use.




NOJA-522-06

Page 51 09-01-2014

NOJA-522-06 3.12

DATA SET DESCRIPTOR – POINT INDEX ATTRIBUTES


This version of the Device Profile document has no requirement for describing Data Set Prototype capabilities and current settings. This page is intentionally left blank, existing as a placeholder for future use.




NOJA-522-06

Page 52 09-01-2014

NOJA-522-06

4 IMPLEMENTATION TABLE The following implementation table identifies which object groups and variations, function codes and qualifiers the device s in both requests and responses. The Request columns identify all requests that may be sent by a Master, or all requests that must be parsed by an Outstation. The Response columns identify all responses that must be parsed by a Master, or all responses that may be sent by an Outstation. For static (non-change-event) objects, requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01. Static object requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or 28. For change-event objects, qualifiers 17 or 28 are always used.

OBJECT Object Number 1

Variation Number 0

Description Binary Input (Variation 0 is used to request default variation)

REQUEST (Library will parse) Function Codes Qualifier Codes (dec) (hex) 1 (read) 00, 01(start-stop) 22(assign class)

RESPONSE (Library will respond with) Function Qualifier Codes (dec) Codes (hex)

06(no range, or all) 07, 08 (limited qty) 17, 28 (index)

1

1

1

2

Binary Input

Binary Input with Status

(default – see note 1)

2

0

2

1

1 (read) 22 (assign class)


Binary Input Change (Variation 0 is used to request default variation)

1 (read)

Binary Input Change without Time

1 (read)

00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 06(no range, or all)

2 (default – see note 1)

Binary Input Change with Time




17, 28 (index – see note 2)

129(response) 00, 01 (startstop) 17, 28 (index – see note 2)

07, 08 (limited qty) 06(no range, or all) 07, 08 (limited qty)

2

129(response) 00, 01 (startstop)

1 (read)

06(no range, or all) 07, 08 (limited qty)

NOJA-522-06

129(response) 17, 28 (index) 130 (unsol. resp) 129(response) 17, 28 (index) 130 (unsol. resp)

Page 53 09-01-2014

NOJA-522-06 OBJECT Object Number 2

Variation Number 3

Description Binary Input Change with Relative Time

REQUEST (Library will parse) Function Codes Qualifier Codes (dec) (hex) 1 (read) 06(no range, or all) 07, 08 (limited qty)

10

0

Binary Output Status (Variation 0 is used to request default variation)

1 (read)

10

1

Binary Output

1 (read)

10

2

Binary Output with Status

1 (read)


12

1

Control Relay Output Block

3 (select) 4 (operate) 5 (direct op) 6 (dir. op, noack)

12

2

Pattern Control Block

12

3

Pattern Mask

20

0

Binary Counter (Variation 0 is used to request default variation)

3 (select) 4 (operate) 5 (direct op) 6 (dir. op, noack) 3 (select) 4 (operate) 5 (direct op) 6 (dir. op, noack) 1 (read) 7 (freeze) 8 (freeze noack) 9 (freeze clear) 10 (frz. cl. noack)

20

1

32-Bit Binary Counter




22 (assign class) 1 (read) 7 (freeze) 8 (freeze noack) 9 (freeze clear) 10 (frz. cl.noack) 22 (assign class) NOJA-522-06

RESPONSE (Library will respond with) Function Qualifier Codes (dec) Codes (hex) 129(response) 17, 28 (index) 130 (unsol. resp)

00, 01 (startstop) 06(no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 07, 08 (limited qty) 17, 28 (index)

129 (response)

00, 01 (startstop) 17, 28 (index – see note 1)


129(response)

echo of request

7 (limited quantity)

129(response)

echo of request

00, 01 (startstop)

129(response)

echo of request

00, 01 (startstop) 06(no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index)


Page 54 09-01-2014

NOJA-522-06 REQUEST (Library will parse) Function Codes Qualifier Codes Description (dec) (hex) 16-Bit Binary Counter 1 (read) 00, 01 (start7 (freeze) stop) 8 (freeze noack) 06 (no range, or 9 (freeze clear) all) 10 (frz. cl.noack) 07, 08 (limited 22 (assign class) qty) 17, 28 (index) 32-Bit Binary Counter without 1 (read) 00, 01 (startFlag 7 (freeze) stop) 8 (freeze noack) 06 (no range, or 9 (freeze clear) all) 10 (frz. cl.noack) 07, 08 (limited 22 (assign class) qty) 17, 28 (index) 16-Bit Binary Counter without 1 (read) 00, 01 (startFlag 7 (freeze) stop) 8 (freeze noack) 06 (no range, or 9 (freeze clear) all) 10 (frz. cl.noack) 07, 08 (limited 22 (assign class) qty) 17, 28 (index) Frozen Counter (Variation 0 1 (read) 00, 01 (startis used to request default stop) variation) 06(no range, or all)

OBJECT Object Number 20

Variation Number 2

20


20

6

21

0

21

1

21

2

32-Bit Frozen Counter

16-Bit Frozen Counter

1 (read)

1 (read)

21

5

32-Bit Frozen Counter with Time Of Freeze

1 (read)

21

6

16-Bit Frozen Counter with Time Of Freeze

1 (read)




NOJA-522-06

07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index)

RESPONSE (Library will respond with) Function Qualifier Codes (dec) Codes (hex) 129(response) 00, 01 (startstop) 17, 28 (index – see note 2)







Page 55 09-01-2014


Variation Number 9 (default – see note 1)

21

10

22

0

22

1

22

2

22


Description 32-Bit Frozen Counter without Flag

16-Bit Frozen Counter without Flag

Counter Change Event (Variation 0 is used to request default variation)

REQUEST (Library will parse) Function Codes Qualifier Codes (dec) (hex) 1 (read) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 1 (read) 06(no range, or all)

32-Bit Counter Change Event

1 (read)

16-Bit Counter Change Event

1 (read)

32-Bit Counter Change Event with Time

1 (read)

6

16-Bit Counter Change Event with Time

1 (read)

23

0

Frozen Counter Event (Variation 0 is used to request default variation)

1 (read)

23

1

32-Bit Frozen Counter Event

1 (read)

23

2

16-Bit Frozen Counter Event

1 (read)

23

5

32-Bit Frozen Counter Event with Time

1 (read)




17, 28 (index – see note 2)


07, 08 (limited qty)

22


RESPONSE (Library will respond with) Function Qualifier Codes (dec) Codes (hex) 129(response) 00, 01 (startstop)

NOJA-522-06

06 (no range, or all) 07, 08 (limited qty) 06 (no range, or all) 07, 08 (limited qty) 06 (no range, or all) 07, 08 (limited qty)

129(response) 17, 28 (index)

129 (response) 130 (unsol. resp)

17, 28 (index)

06 (no range, or all) 07, 08 (limited qty) 06 (no range, or all) 07, 08 (limited qty) 06 (no range, or all) 07, 08 (limited qty) 06 (no range, or all) 07, 08 (limited qty) 06 (no range, or all) 07, 08 (limited qty)


17, 28 (index)

129 (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp)

17, 28 (index)

130 (unsol. resp) 129(response) 17, 28 (index) 130 (unsol. resp)

17, 28 (index)

17, 28 (index)

Page 56 09-01-2014


Variation Number 6

30

0

30

1

Description 16-Bit Frozen Counter Event with Time

Anaput (Variation 0 is used to request default variation)

32-Bit Anaput


30

2

30

3

30

4

32

0

32

1

32

2

16-Bit Anaput

32-Bit Anaput without Flag

16-Bit Anaput without Flag




1 (read)

32-Bit Analog Change Event without Time

1 (read)

16-Bit Analog Change Event without Time

1 (read)




Analog Change Event (Variation 0 is used to request default variation)


REQUEST (Library will parse) Function Codes Qualifier Codes (dec) (hex) 1 (read) 06 (no range, or all) 07, 08 (limited qty) 1 (read) 00, 01 (startstop) 22 (assign class) 06(no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 06(no range, or all)

RESPONSE (Library will respond with) Function Qualifier Codes (dec) Codes (hex) 129 17, 28 (index) (response) 130 (unsol. resp)






NOJA-522-06

06 (no range, or all) 07, 08 (limited qty) 06 (no range, or all) 07, 08 (limited qty)

129(response) 17, 28 (index) 130 (unsol. resp) 129(response) 17, 28 (index) 130 (unsol. resp)

Page 57 09-01-2014


Variation Number 3 (default – see note 1)

Description 32-Bit Analog Change Event with Time

REQUEST (Library will parse) Function Codes Qualifier Codes (dec) (hex) 1 (read) 06 (no range, or all) 07, 08 (limited qty)

RESPONSE (Library will respond with) Function Qualifier Codes (dec) Codes (hex) 129 17, 28 (index) (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp)

17, 28 (index)

129 (response)


129 (response)


129 (response)


32

4

16-Bit Analog Change Event with Time

1 (read)

34

0

Anaput Reporting Deadband (Variation 0 is used to request default variation)

1 (read)

34

1

16-Bit Anaput Reporting Deadband

1 (read)


2 (write)

34

2

32-Bit Anaput Reporting Deadband

1 (read)

2 (write)

50

0

Time and Date




1 (read)

NOJA-522-06

06 (no range, or all) 07, 08 (limited qty) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 07, 08 (limited qty) 17, 28 (index) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index)

Page 58 09-01-2014


Variation Number 1

Description Time and Date


REQUEST (Library will parse) Function Codes Qualifier Codes (dec) (hex) 1 (read) 00, 01 (startstop) 06 (no range, or all) 07 (limited qty=1) 08 (limited qty) 17, 28 (index) 2 (write) 00, 01 (startstop) 07(limited qty=1)

RESPONSE (Library will respond with) Function Qualifier Codes (dec) Codes (hex) 129 00, 01 (start(response) stop) 17, 28 (index – see note 2)

08 (limited qty) 17, 28 (index) 51

1

51

2

52

2

Time and Date CTO (synchronized)

129(response) 07(limited qty)

Time and Date CTO (unsynchronized)


Time Delay Fine


130 (unsol. resp)

130 (unsol. resp)

(qty = 1)

(qty = 1)

(qty = 1) 60

1

Class 0 Data


06(no range, or all)

60

2

Class 1 Data

1

06(no range, or all)

(read)


60

3

Class 2 Data

20 (enbl. unsol.) 21 (dsbl. unsol.) 22 (assign class) 1 (read)

06 (no range, or all) 06(no range, or all) 07, 08 (limited qty)

60

4

Class 3 Data

20 (enbl. unsol.) 21 (dsbl. unsol.) 22 (assign class) 1 (read)

06 (no range, or all) 06(no range, or all) 07, 08 (limited qty)

20 (enbl. unsol.) 21 (dsbl. unsol.) 22 (assign class)




NOJA-522-06

06 (no range, or all)

Page 59 09-01-2014

NOJA-522-06 REQUEST (Library will parse) Variation Function Codes Qualifier Codes Description Number (dec) (hex) 0 Internal Indications (Variation 1 (read) 00, 01 (start0 is used to request default stop) variation) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 1 Internal Indications 1 (read) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) 17, 28 (index) 2 (write) 00 (start-stop) (see note 4) 01 (start-stop) 07, 08 (limited qty) 17, 28 (index) string Octet String Object 1 (read) 06 (no range, or length all) 07, 08 (limited qty) 2 (write) 00, 01 (startstop) 07, 08 (limited qty) 17, 28 (index) 22 (assign class) 00, 01 (startstop) 06 (no range, or all) 07, 08 (limited qty) No Object (function code only) – See 13(cold restart) Note 3 OBJECT

Object Number 80

80

110

No Object (function code only) – See Note 3 No Object (function code only)

RESPONSE (Library will respond with) Function Qualifier Codes (dec) Codes (hex)

129 (response)



17, 28 (index)

129 (response)

00, 01 (startstop)

14 (warm restart) 23(delay meas.)

Note 1: A Default variation refers to the variation responded when variation 0 is requested and/or in class 0, 1, 2, or 3 scans. Default variations may be configurable; however, default settings for the configuration parameters are indicated in the table above. Note 2: For static (non-change-event) objects, qualifiers 17 or 28 are only responded when a request is sent with qualifiers 17 or 28, respectively. Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01. (For change-event objects, qualifiers 17 or 28 are always responded.) Note 3: Both cold restart and warm restart affect ONLY the DNP process. The RC10 itself is not restarted. Note 4: Writes of Internal Indications are only ed for index 7 (Restart IIN1-7).




NOJA-522-06

Page 60 09-01-2014

NOJA-522-06

5 DATA POINTS LIST (OUTSTATION ONLY) This part of the Device Profile shows, for each data type. a table defining the data points available in the device or a description of how this information can be obtained if the database is configurable. Tables for data types not ed may be deleted. Additional columns may be added to the point list table if necessary.




NOJA-522-06

Page 61 09-01-2014

NOJA-522-06 5.1

DEFINITION OF BINARY INPUT POINT LIST:

List all addressable points. Points that do not exist (for example, because an option is not installed) shall be omitted from the table.

Fixed, list shown in table below Configurable (current list may be shown in table below) Other, explain_____________________

Note: the number of binary inputs present in the device, and the maximum binary input index, are available remotely using object Group 0 Variations 239 and 238.

Static (Steady-State) Object Number:

1

Change Event Object Number:

2

Request Function Codes ed:

1 (read), 22 (assign class)

Default Static Variation reported when variation 0 requested:

(Note 1) 1 (Binary Input without status)

Default Change Event Variation reported when variation 0 requested:

(Note 1) 2 (Binary Input Change with Time)

Status bits ed:

on-line, local forced data, state

Note 1: The actual variation reported in response to a variation 0 request can be configured on a per-point basis.

Note: All binary inputs are considered permanently online On-line (0), local forced data (1). Binary input change events are detected by the IED at the time they occur and are not subject to a scan rate. Time stamps associated with change events correspond to the time stamp appearing on the HMI or CMS Event, CO Operation or Change Messages logs. The value in the Default DNP ID column represents the default setting. This parameter is configurable between 0 and 255, individual points can be selected for mapping or disabled using the CMS software. Changes to class allocation arising from use of DNP3 function 22 are saved to volatile memory.

Data group

Default DNP ID

Database ID

Conditions when set (=1)

Conditions when clear (=0)

Default Class

Single Phase Recloser

General 0

Indication

Dummy Control

Dummy Control ON

Dummy Control OFF

1

Yes

Disabled 1

Indication Indication

Test Mode Lockout

Test Mode is OFF ACR is not in the Lockout state

0 1

Yes Yes

Disabled

Indication

79_Lockout

Test Mode is ON ACR is in the open state and will not close automatically Lockout due to any Protection Operation and with any number of trips

Recloser is not in Lockout state due to Protection Operation

0

Yes




NOJA-522-06

Page 62 09-01-2014

NOJA-522-06 Data group

Default DNP ID

2

Indication


Database ID



Default Class

Remote Control

Control mode is set Remote

Control mode is set Local.

1

Yes

2

Yes

2

Yes

0

Yes

Trip request by Group 1 protection settings Trip request by Group 2 protection settings Trip request by Group 3 protection settings Trip request by Group 4 protection settings Maximum Number of Trips exceeded

No AR initiated or Pickup signals detected Control mode is set Remote No Group 1 protection trip request detected. No Group 2 protection trip request detected. No Group 3 protection trip request detected. No Group 4 protection trip request detected. Maximum Number of Trips not exceeded

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

Pickup output of any element is activated Pickup output of OC1+ activated Pickup output of OC2+ activated Pickup output of OC3+ activated Pickup output of OC1activated Pickup output of OC2activated Pickup output of OC3activated Pickup output of NPS1+ activated Pickup output of NPS2+ activated Pickup output of NPS3+ activated Pickup output of NPS1activated Pickup output of NPS2activated Pickup output of NPS3activated Pickup output of EF1+ activated Pickup output of EF2+

No Pickup output of any element activated Pickup output of OC1+ not activated Pickup output of OC2+ not activated Pickup output of OC3+ not activated Pickup output of OC1- not activated Pickup output of OC2- not activated Pickup output of OC3- not activated Pickup output of NPS1+ activated Pickup output of NPS2+ activated Pickup output of NPS3+ activated Pickup output of NPS1activated Pickup output of NPS2activated Pickup output of NPS3activated Pickup output of EF1+ not activated Pickup output of EF2+ not

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

No

0

No

3

Indication

AR initiated

4

Indication

Prot initiated

Disabled

Indication

Local Control

Disabled

Indication

Group 1 Trip

Disabled

Indication

Group 2 Trip

Disabled

Indication

Group 3 Trip

Disabled

Indication

Group 4 Trip

Disabled

Indication

MNT Exceeded

Disabled

Indication

Pickup

Disabled

Indication

P(OC1+)

Disabled

Indication

P(OC2+)

Disabled

Indication

P(OC3+)

Disabled

Indication

P(OC1- )

Disabled

Indication

P(OC2- )

Disabled

Indication

P(OC3- )

Disabled

Indication

P(NPS1+)

Disabled

Indication

P(NPS2+)

Disabled

Indication

P(NPS3+)

Disabled

Indication

P(NPS1-)

Disabled

Indication

P(NPS2-)

Disabled

Indication

P(NPS3-)

Disabled

Indication

P(EF1+)

Disabled

Indication

P(EF2+)

Any of AR OC/NPS/EF/SEF, AR VE or ABR elements are set in an open state, and a reclose operation is pending Logical OR of AR initiated and Pickup signals Control mode is set Local

IIN1-5 Local mode indicator is set None of AR OC/EF/SEF, AR VE or ABR elements are set in an open state with a pending reclose operation.

Pickup




NOJA-522-06

Page 63 09-01-2014

NOJA-522-06 Default DNP ID

Data group Database ID

Disabled

Indication

P(EF3+)

Disabled

Indication

P(EF1-)

Disabled

Indication

P(EF2- )

Disabled

Indication

P(EF3- )

Disabled

Indication

P(SEF+)

Disabled

Indication

P(SEF- )

Disabled

Indication

P(OCLL1)

Disabled

Indication

P(OCLL2)

Disabled

Indication

P(OCLL3)

Disabled

Indication

P(NPSLL1)

Disabled

Indication

P(NPSLL2)

Disabled

Indication

P(NPSLL3

Disabled

Indication

P(EFLL1)

Disabled

Indication

P(EFLL2

Disabled

Indication

P(EFLL3)

Disabled

Indication

P(SEFLL)

Disabled

Indication

P(PhA)

Disabled

Indication

P(PhB)

Disabled

Indication

P(PhC)

Disabled

Indication

P(PhN)

Disabled

Indication

P(UV1)

Disabled

Indication

P(UV2)

Disabled

Indication

P(UV3)

Disabled

Indication

P(OV1)

Disabled

Indication

P(OV2)

Disabled

Indication

P(UF)

Disabled

Indication

P(OF)






activated

activated

Pickup output of EF3+ activated Pickup output of EF1activated Pickup output of EF2activated Pickup output of EF3activated Pickup output of SEF+ activated Pickup output of SEFactivated Pickup output of OCLL1 activated Pickup output of OCLL2 activated Pickup output of OCLL3 activated Pickup output of NPSLL1 activated Pickup output of NPSLL2 activated Pickup output of NPSLL3 activated Pickup output of EFLL1 activated Pickup output of EFLL2 activated Pickup output of EFLL3 activated Pickup output of SEFLL activated Pickup output of Phase A activated by OC element Pickup output of Phase B activated by OC element Pickup output of Phase C activated by OC element Pickup output of Phase N activated by EF element Pickup output of UV1 activated Pickup output of UV2 activated Pickup output of UV3 activated Pickup output of OV1 activated Pickup output of OV2 activated Pickup output of UF activated Pickup output of OF

Pickup output of EF3+ not activated Pickup output of EF1- not activated Pickup output of EF2- not activated Pickup output of EF3- not activated Pickup output of SEF+ not activated Pickup output of SEF- not activated Pickup output of OCLL1 not activated Pickup output of OCLL2 not activated Pickup output of OCLL3 not activated Pickup output of NPSLL1 activated Pickup output of NPSLL2 activated Pickup output of NPSLL3 activated Pickup output of EFLL1 not activated Pickup output of EFLL2 not activated Pickup output of EFLL3 not activated Pickup output of SEFLL not activated Pickup output of Phase A not activated Pickup output of Phase B not activated Pickup output of Phase C not activated Pickup output of Phase N not activated Pickup output of UV1 not activated Pickup output of UV2 not activated Pickup output of UV3 not activated Pickup output of OV1 not activated Pickup output of OV2 not activated Pickup output of UF not activated Pickup output of OF not

NOJA-522-06

Default Class


0

No

0

No

0

No

0

No

0

No

0

No

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

No

0

No

0

No

0

No

0

Yes

0

No

0

No

0

No

0

Yes

0

No

0

Yes

0

Yes

0

No

0

Yes

0

Yes Page 64 09-01-2014

NOJA-522-06 Data group

Default DNP ID

Database ID



activated Pickup output of Uabc> activated Pickup output of Urst> activated Pickup output of Uabc< activated Pickup output of Urst< activated Pickup output of Loss of Supply Detector activated

activated Pickup output of Uabc> not activated Pickup output of Urst> not activated Pickup output of Uabc< not activated Pickup output of Urst< not activated Pickup output of Loss of Supply Detector not activated Voltage on A bushing is below LSD level Voltage on B bushing is below LSD level Voltage on C bushing is below LSD level Voltage on R bushing is below LSD level Voltage on S bushing is below LSD level Voltage on T bushing is below LSD level

Disabled

Indication

P(Uabc>)

Disabled

Indication

P(Urst>)

Disabled

Indication

P(Uabc<)

Disabled

Indication

P(Urst<)

Disabled

Indication

P(LSD)

Disabled

Indication

P(Ua)

Disabled

Indication

P(Ub)

Disabled

Indication

P(Uc)

Disabled

Indication

P(Ur)

Disabled

Indication

P(Us)

Disabled

Indication

P(Ut)

5

Indication

Open(Any)

6

Indication

Open(Prot)

7

Indication

Open(OC1+)

PS=0 irrespective of source Open due to any protection trip Open due to OC1+ tripping

8

Indication

Open(OC2+)

Open due to OC2+ tripping

9

Indication

Open(OC3+)

Open due to OC3+ tripping

Disabled

Indication

Open(OC1-)

Open due to OC1- tripping

Disabled

Indication

Open(OC2- )


Disabled

Indication

Open(OC3- )


Disabled

Indication

Open(NPS1+)

Disabled

Indication

Open(NPS2+)

Disabled

Indication

Open(NPS3+)

Disabled

Indication

Open(NPS1-)

Disabled

Indication

Open(NPS2-)

Disabled

Indication

Open(NPS3-)

Open due to NPS1+ tripping Open due to NPS2+ tripping Open due to NPS3+ tripping Open due to NPS1tripping Open due to NPS2tripping Open due to NPS3tripping

Voltage on A bushing is above LSD level Voltage on B bushing is above LSD level Voltage on C bushing is above LSD level Voltage on R bushing is above LSD level Voltage on S bushing is above LSD level Voltage on T bushing is above LSD level

Default Class


0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

No

0

No

0

Yes

0

No

0

No

1

Yes

1

Yes

2

Yes

2

Yes

2

Yes

0

Yes

0

Yes

0

Yes

0

No

0

No

0

No

0

No

0

No

0

No

Open




PS=1 irrespective of source Not open due to any protection trip Not open due to OC1+ tripping Not open due to OC2+ tripping Not open due to OC3+ tripping Not open due to OC1tripping Not open due to OC2tripping Not open due to OC3tripping Not open due to NPS1+ tripping Not open due to 2+ tripping Not open due to NPS3+ tripping Not open due to NPS1tripping Not open due to NPS2tripping Not open due to NPS3tripping

NOJA-522-06

Page 65 09-01-2014





10

Indication

Open(EF1+)

Open due to EF1+ tripping

11

Indication

Open(EF2+)


12

Indication

Open(EF3+)


Disabled

Indication

Open(EF1-)

Open due to EF1- tripping

Disabled

Indication

Open(EF2-)


Disabled

Indication

Open(EF3-)


13

Indication

Open(SEF+)

Open due to SEF+ tripping

Disabled

Indication

Open(SEF-)

Open due to SEF- tripping

Disabled

Indication

Open(PhA)

Disabled

Indication

Open(PhB)

Disabled

Indication

Open(PhC)

Disabled

Indication

Open(PhN)

Disabled

Indication

Open(OCLL1)

Disabled

Indication

Open(OCLL2)

Disabled

Indication

Open(OCLL3)

Disabled

Indication

Open(NPSLL1)

Disabled

Indication

Open(NPSLL2)

Disabled

Indication

Open(NPSLL3)

Disabled

Indication

Open(EFLL1)

Disabled

Indication

Open(EFLL2)

Disabled

Indication

Open(EFLL3)

Disabled

Indication

Open(SEFLL)

16

Indication

Open(UV1)

Open due to Phase A tripping by OC element Open due to Phase B tripping by OC element Open due to Phase C tripping by OC element Open due to Phase N tripping by EF element Open due to OCLL1 tripping Open due to OCLL2 tripping Open due to OCLL3 tripping Open due to NPSLL1 tripping Open due to NPSLL2 tripping Open due to NPSLL3 tripping Open due to EFLL1 tripping Open due to EFLL2 tripping Open due to EFLL3 tripping Open due to SEFLL tripping Open due to UV1 tripping

17

Indication

Open(UV2)

Open due to UV2 tripping

18

Indication

Open(UV3)

Open due to UV3 tripping

Disabled

Indication

Open(OV1)

Open due to OV1 tripping

Disabled

Indication

Open(OV2)

Open due to OV2 tripping

Not open due to EF1+ tripping Not open due to EF2+ tripping Not open due to EF3+ tripping Not open due to EF1tripping Not open due to EF2tripping Not open due to EF3tripping Not open due to SEF+ tripping Not open due to SEFtripping Not open due to Phase A tripping Not open due to Phase B tripping Not open due to Phase C tripping Not open due to Phase N tripping Not open due to OCLL1 tripping Not open due to OCLL2 tripping Not open due to OCLL3 tripping Not open due to NPSLL1 tripping Not open due to NPSLL2 tripping Not open due to NPSLL3 tripping Not open due to EFLL1 tripping Not open due to EFLL2 tripping Not open due to EFLL3 tripping Not open due to SEFLL tripping Not open due to UV1 tripping Not open due to UV2 tripping Not open due to UV3 tripping Not open due to OV1 tripping Not open due to OV2 tripping




NOJA-522-06

Default Class


2

No

2

No

2

No

0

No

0

No

0

No

2

No

0

No

0

Yes

0

No

0

No

0

No

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

0

Yes

2

Yes

2

No

2

Yes

0

Yes

0

No

Page 66 09-01-2014


Data group

Default Class


Database ID



Disabled

Indication

Open(UF)

Open due to UF tripping

0

Yes

Disabled

Indication

Open(OF)

Open due to OF tripping

0

Yes

19

Indication

Open (Remote)

0

Yes

Disabled

Indication

Open(SCADA)

0

Yes

Disabled

Indication

Open(I/O)

0

Yes

20

Indication

Open(Local)

0

Yes

Disabled

Indication

Open(HMI)

0

Yes

Disabled

Indication

Open(PC)

0

Yes

Disabled

Indication

Open(Manual)

0

Yes

Disabled

Indication

Open(Undefined)

Not open after On (Power) or switch reconnection.

0

Yes

Disabled

Indication

Yes

Indication

Not open due to ABR AutoOpen operation. Not open due to Auto Change Over control signal

0

Disabled

Open(ABR AutoOpen) Open(ACO)

Open due to Remote mode control signal Open due to SCADA control signal Open due to I/O control signal Open due to Local mode control signal or manual tripping Open due to HMI control signal Open due to PC control signal Open due to manual tripping (no origin detected) Open state recognized after On (Power) or switch reconnection Open due to ABR AutoOpen operation Open due to Auto Change Over control signal

Not open due to UF tripping Not open due to OF tripping Not open due to Remote mode control signal Not open due to SCADA control signal Not open due to I/O control signal Not open due to Local mode control signal or manual tripping Not open due to HMI control signal Not open due to PC control signal Not open due to manual tripping

0

Yes

21

Indication

Alarm (Any)

0

Yes

Disabled

Indication

A(OC1+)

0

Yes

Disabled

Indication

A(OC2+)

0

Yes

Disabled

Indication

A(OC1-)

0

Yes

Disabled

Indication

A(OC2-)

0

Yes

Disabled

Indication

A(NPS1+)

0

Yes

Disabled

Indication

A(NPS2+)

0

Yes

Disabled

Indication

A(NPS1-)

0

Yes

Disabled

Indication

A(NPS2-)

0

Yes

Disabled

Indication

A(EF1+)

0

No

Disabled

Indication

A(EF2+)

0

No

Disabled

Indication

A(EF1-)

0

No

Disabled

Indication

A(EF2-)

No Alarm output of any element activated Alarm output of OC1+ not activated Alarm output of OC2+ not activated Alarm output of OC1- not activated Alarm output of OC2- not activated Alarm output of NPS1+ not activated Alarm output of NPS2+ not activated Alarm output of NPS1- not activated Alarm output of NPS2- not activated Alarm output of EF1+ not activated Alarm output of EF2+ not activated Alarm output of EF1- not activated Alarm output of EF2- not activated

0

No

Alarms




Alarm output of any element activated Alarm output of OC1+ activated Alarm output of OC2+ activated Alarm output of OC1activated Alarm output of OC2activated Alarm output of NPS1+ activated Alarm output of NPS2+ activated Alarm output of NPS1activated Alarm output of NPS2activated Alarm output of EF1+ activated Alarm output of EF2+ activated Alarm output of EF1activated Alarm output of EF2activated

NOJA-522-06

Page 67 09-01-2014


Data group

Default Class


Database ID



Disabled

Indication

A(SEF+)

No

Indication

A(SEF-)

0

No

Disabled

Indication

A(PhA)

0

Yes

Disabled

Indication

A(PhB)

0

No

Disabled

Indication

A(PhC)

0

No

Disabled

Indication

A(PhN)

0

No

Disabled

Indication

A(UV1)

0

Yes

Disabled

Indication

A(UV2)

0

No

Disabled

Indication

A(UV3)

0

Yes

Disabled

Indication

A(OV1)

0

Yes

Disabled

Indication

A(OV2)

0

No

Disabled

Indication

A(UF)

0

Yes

Disabled

Indication

A(OF)

Alarm output of SEF+ not activated Alarm output of SEF- not activated Alarm output of Phase A not activated Alarm output of Phase B not activated Alarm output of Phase C not activated Alarm output of Phase N not activated Alarm output of UV1 not activated Alarm output of UV2 not activated Alarm output of UV3 not activated Alarm output of OV1 not activated Alarm output of OV2 not activated Alarm output of UF not activated Alarm output of OF not activated

0

Disabled

Alarm output of SEF+ activated Alarm output of SEFactivated Alarm output of Phase A activated by OC element Alarm output of Phase B activated by OC element Alarm output of Phase C activated by OC element Alarm output of Phase N activated by EF element Alarm output of UV1 activated Alarm output of UV2 activated Alarm output of UV3 activated Alarm output of OV1 activated Alarm output of OV2 activated Alarm output of UF activated Alarm output of OF activated

0

Yes

22 23


Closed(Any) Closed(AR)

Yes Yes

Indication

0

Yes

Disabled

Indication

Closed(AR OCNPSEFSEF) Closed(AR VE)

0

Yes

Disabled

Indication

Closed(ABR)

0

Yes

Disabled

Indication

Closed (Remote)

0

Yes

Disabled

Indication

Closed (SCADA)

0

Yes

24

Indication

Closed(I/O)

0

Yes

25

Indication

Closed (Local)

0

Yes

Disabled

Indication

Closed(HMI)

0

Yes

Disabled

Indication

Closed(PC)

0

Yes

Disabled

Indication

Closed(Undefined)

0

Yes

Disabled

Indication

Closed(ABR AutoOpen)

PS=0 irrespective of origin Not closed due to AR OC/EF/SEF, AR UV, ABR control signal Not closed due to AR OC/EF/SEF reclosing Not closed due to AR VE reclosing Not closed due to ABR closing Not closed due to Remote control signal Not closed due to SCADA control signal Not closed due to I/O control signal Not closed due to Local control signal Not closed due to HMI control signal Not closed due to PC control signal Not closed after On (Power) or switch reconnection. Not closed due to an ABR Auto Open operation.

0 0

Disabled

PS=1 irrespective of origin Closed due to AR OC/EF/SEF, AR VE, ABR control signal Closed due to AR OC/NPS/EF/SEF reclosing Closed due to AR VE reclosing Closed due to ABR closing

0

Yes

Closed




Closed due to Remote control signal Closed due to SCADA control signal Closed due to I/O control signal Closed due Local control signal Closed due to HMI control signal Close due to PC control signal Closed state recognized after On (Power) or switch reconnection. Closed due to a ABR operation while an ABR

NOJA-522-06

Page 68 09-01-2014


Disabled


Default Class




Auto Open operation count is active Closed due to a ACO control signal

Not closed due to an ACO control signal

0

Yes

Indication

Closed (ACO)

26

Indication

Group1 On

Active Group 1

Active Group 2, 3 or 4

0

Yes

27

Indication

Group2 On

Active Group 2

Active Group 1, 3 or 4

0

Yes

28 29


Group3 On Group4 On

Active Group 3 Active Group 4

Active Group 1,2 or 4 Active Group 1, 2 or 3

0 0

Yes Yes

30

Indication

Prot On

Protection is switched On

Protection is switched Off

0

Yes

Disabled

Indication

NPS On

Yes

Indication

EF On

0

No

32

Indication

SEF On

0

No

33

Indication

UV On

0

Yes

Disabled

Indication

UF On

0

Yes

Disabled

Indication

OV On

0

Yes

Disabled

Indication

OF On

0

Yes

34

Indication

CLP On

0

Yes

35

Indication

LL On

0

Yes

36

Indication

AR On

0

Yes

37

Indication

ABR On

0

Yes

Disabled

Indication

Hot Line Tag On

Negative Phase Sequence Off Earth overcurrent element is switched Off Sensitive Earth fault element is switched Off Undervoltage element is switched Off Underfrequency element is switched Off Overvoltage element is switched Off Overfrequency element is switched Off Cold load pickup element is switched Off Live line element is switched Off OC/EF/SEF and VE reclosing is switched Off Automatic backfeed restoration is switched Off Hot Line Tag is turned off

0

31

Negative Phase Sequence On Earth overcurrent element is switched On Sensitive Earth fault element is switched On Undervoltage element is switched On Underfrequency element is switched On Overvoltage element is switched On Overfrequency element is switched On Cold load pickup element is switched On Live line element is switched on OC/EF/SEF and VE reclosing is switched On Automatic backfeed restoration is switched On Hot Line Tag is turned on

0

Yes

Disabled

Indication

0

Yes

Disabled

Indication

0

Yes

Disabled

Indication

DFT On

0

Yes

Disabled

Indication

Block Close On

Maximum Number of Trips to Lockout is not set to 2 Maximum Number of Trips to Lockout is not set to 3 Short Sequence Mode is not selected Disable Fast Trips is disabled Block Close is OFF

Yes

Indication

Maximum Number of Trips to Lockout is set to 2 Maximum Number of Trips to Lockout is set to 3 Short Sequence Mode is selected Disable Fast Trips is enabled Block Close is ON

0

Disabled

79-2 Trips to Lockout 79-3 Trips to Lockout SSM On

0

Yes

Disabled

Indication

ACO On

Auto Change Over is ON

Auto Change Over is OFF

0

Yes

Disabled

Indication

MNT On

Maximum Number of Trips is ON

Maximum Number of Trips is OFF

0

Yes

Malfunction

Any malfunction signal activated IIN1-6 Device Trouble Indicator set

No malfunction signal activated

1

Yes

Status

Malfunctions 38

Indication




NOJA-522-06

Page 69 09-01-2014


Data group

Default Class


Database ID



Disabled

Indication

External load overload

External load overload not detected

0

Yes

Disabled

Indication

Battery charger fault

Battery charger status is other than 'Fail'.

0

Yes

Disabled

Indication

OSM Fault

OSM fault not detected

0

Yes

Disabled

Indication

SIM Module Fault

SIM Module fault not detected

0

Yes

Disabled

Indication

SIM Comms Error

External load overload detected IIN1-6 Device Trouble Indicator set Battery charger status is 'Fail'. IIN1-6 Device Trouble Indicator set Active due to 1, 2 or 3xCoil OC; Limit switch fault, Coil SC , excessive To, excessive Tc IIN1-6 Device Trouble Indicator set SIM Module Fault detected. IIN1-6 Device Trouble Indicator set No response from SIM.

0

Yes

I/O1 Comms Error

IIN1-6 Device Trouble Indicator set No response from I/O1.

SIM comms error not detected

0

Yes

I/O2 Comms Error

IIN1-6 Device Trouble Indicator set No response from I/O2.

I/O1 comms error not detected I/O2 comms error not detected

0

Yes

The Excessive To flag is reset.

0

Yes

The Excessive Tc flag is reset

0

Yes

OSM coil open circuit not detected

0

Yes

OSM coil short circuit not detected

0

Yes

Disabled

Disabled

Indication

Indication

Disabled

Indication

Excessive To

Disabled

Indication

Excessive Tc

Disabled

Indication

OSM Coil OC

Disabled

Indication

OSM Coil SC




IIN1-6 Device Trouble Indicator set The most recent trip request failed because the opening time exceeded 60ms or no confirmation received that open command was executed successfully. IIN1-6 Device Trouble Indicator set The most recent close request failed because the time to close exceeded 100ms, or no confirmation received that open command was executed successfully IIN1-6 Device Trouble Indicator set OSM coil open circuit detected. IIN1-6 Device Trouble Indicator set OSM coil short circuit detected. IIN1-6 Device Trouble Indicator set

NOJA-522-06

Page 70 09-01-2014


Data group

Default Class


Database ID



Disabled

Indication

OSM Limit Switch Fault

OSM limit switch fault not detected

0

Yes

Disabled

Indication

Capacitor Voltage Abnormal

No fault with capacitor voltage detected.

0

Yes

Disabled

Indication

Module Comms Error

No fault with SIM or I/O comms detected

0

Yes

Disabled

Indication

Comms Error

No fault with comms detected

0

Yes

Disabled

Indication

Controller Fault

No fault with controller detected

0

Yes

Disabled

Indication

Controller Module Fault

No controller module fault detected

0

Yes

Disabled

Indication

Module fault

No Internal fault of module detected

0

Yes

Disabled

Indication

Relay Module fault

No Internal fault of relay module detected

0

Yes

Disabled

Indication

CAN Bus Malfunction

OSM limit switch fault detected. IIN1-6 Device Trouble Indicator set Close volt drop too high, Trip volt drop too high, Trip volt drop on close IIN1-6 Device Trouble Indicator set SIM or I/O module comms error detected IIN1-6 Device Trouble Indicator set comms error detected IIN1-6 Device Trouble Indicator set Active due to CAN bus Malfunction, module fault, comms error or Ext. load overload IIN1-6 Device Trouble Indicator set Active due to module, SIM disconnected, SIM fault, I/O1 fault, I/O2 fault or relay fault IIN1-6 Device Trouble Indicator set Internal fault of module detected IIN1-6 Device Trouble Indicator set Internal fault of relay module detected IIN1-6 Device Trouble Indicator set Error reported on CAN bus

No error detected on CAN bus

0

Yes

No I/O1 internal fault detected

0

Yes

No I/O2 internal fault detected

0

Yes

No warning signal activated OSM position status is available

1

Yes

0

Yes

Disabled

Disabled

Indication

Indication

I/O1 fault

IIN1-6 Device Trouble Indicator set I/O1 internal fault detected

I/O2 fault

IIN1-6 Device Trouble Indicator set I/O2 internal fault detected IIN1-6 Device Trouble Indicator set

Warnings 39

Indication

Warning

Disabled

Indication

OSM Position Status Unavailable




Any warning signal activated OSM position status is unavailable due to being

NOJA-522-06

Page 71 09-01-2014



40

Indication

OSM Disconnected OSM Mechanically Locked Out

Disabled

Indication

Disabled

Indication

Disabled

Indication

Disabled

Indication

Disabled

Indication

Disabled

Indication

Disabled

Indication

Disabled

Indication

Close Blocked

Disabled

Indication

AC Supply High

Disabled

Indication

Source Not Healthy

Disabled

Indication

ACO Unhealthy

SIM Caps Not Charged Battery Status Abnormal Battery Charger State: Low Power Battery Off (AC Supply) AC Off (Battery Supply) Critical Battery Level

Default Class




disconnected or a malfunction OSM disconnected

OSM connected

1

Yes

OSM mechanically locked out, trip ring pulled down

OSM is not mechanically locked out.

2

Yes

SIM actuator driver not ready Battery is either high, low or disconnected Battery charger state is in low power mode UPS is in 'Battery Off' state

SIM actuator driver ready

0

Yes

Battery status is normal

0

Yes

Battery charger state is normal UPS is not in 'Battery Off' state UPS is not in 'AC Off' state

0

Yes

0

Yes

0

Yes

System shutdown in less than 5 min due to low battery level Close is blocked by any source AC voltage high

Battery level is non-critical

0

Yes

Close is not blocked

0

Yes

AC voltage is not high

0

Yes

Source detected as outside specified supply parameters Conditions detected not to allow an ACO operation

Source supply healthy

0

Yes

Conditions allow an ACO operation

0

Yes

UPS is in 'AC Off' state

IO Modules Disabled

Indication

Local Input IN1

Input asserted

Input not asserted

0

Yes

Disabled

Indication

Local Input IN2

Input asserted

Input not asserted

0

Yes

Disabled

Indication

Local Input IN3

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO1 Input 1

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO1 Input 2

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO1 Input 3

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO1 Input 4

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO1 Input 5

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO1 Input 6

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO1 Input 7

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO1 Input 8

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO2 Input 1

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO2 Input 2

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO2 Input 3

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO2 Input 4

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO2 Input 5

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO2 Input 6

Input asserted

Input not asserted

0

Yes

Disabled

Indication

IO2 Input 7

Input asserted

Input not asserted

0

Yes




NOJA-522-06

Page 72 09-01-2014


Data group

Default Class


Database ID



IO2 Input 8

Input asserted

Input not asserted

0

Yes

Logic Variables Disabled Indication

VAR1

Logic Variable 1 True

Logic Variable 1 False

0

Yes

Disabled

Indication

VAR2



0

Yes

Disabled

Indication

VAR3



0

Yes

Disabled

Indication

VAR4



0

Yes

Disabled

Indication

VAR5



0

Yes

Disabled

Indication

VAR6



0

Yes

Disabled

Indication

VAR7



0

Yes

Disabled

Indication

VAR8



0

Yes

Disabled

Indication




NOJA-522-06

Page 73 09-01-2014

NOJA-522-06 5.2

DEFINITION OF DOUBLE-BIT INPUT POINT LIST: List all addressable points. Points that do not exist (for example, because an option is not installed) shall be omitted from the table.

Fixed, list shown in table below Configurable (current list may be shown in table below) Other, explain – Not ed

Note: the number of double-bit inputs present in the device, and the maximum double-bit input index, are available remotely using object Group 0 Variations 236 and 235.




NOJA-522-06

Page 74 09-01-2014

NOJA-522-06 5.3

DEFINITION OF BINARY OUTPUT STATUS/CONTROL RELAY OUTPUT BLOCK (CROB) POINT LIST:


List all addressable points. Points that do not exist (for example, because an option is not installed) shall be omitted from the table. Note: the number of binary outputs present in the device, and the maximum binary output index, are available remotely using object Group 0 Variations 224 and 223. Object Number: Request Function Codes ed: Default Variation reported when variation 0 requested: Status bits ed:

10 1 (read) (Note 1) 2 (Binary Output with Status) on-line, communications lost, local forced data, state Note 1: The actual variation reported in response to a variation 0 request can be configured on a per-point basis. Notes: The count, on-time, off-time, queue, and clear parameters are ignored for all points. Condition(s) for Obj 10 var 2 status for each point is indicated below where applicable, also refer notes at the end of the table. Control Relay Output Blocks Object Number: 12 Request Function Codes ed: Accepted control types are:

3 (select), 4 (operate), 5 (direct operate), 6 (direct operate, noack) Control Type Control Code Accepted by Pulse ON 0x01 All Points Pulse OFF 0x02 All Points Latch ON 0x03 All Points Latch OFF 0x04 All Points Close 0x41 All Points Trip 0x81 All Points

The recommended control type is shown in the table below. Set (1)

Close, Pulse ON, Latch ON

Cleared (0)

Trip, Pulse OFF, Latch OFF

The value in the Default DNP ID column represents the default setting. This parameter is configurable between 0 and 255, individual points can be selected for mapping or disabled using CMS software.




NOJA-522-06

Page 75 09-01-2014


Single Phase Recloser Yes

0

Data group Control

Database ID Dummy Control

Set = 1 Dummy Control ON

Clear = 0 Dummy Control OFF

Disabled

Control

Test Mode

Test Mode ON

Test Mode OFF

Recommended control type Can be used to test all control types Latch ON / Latch OFF

1

Control

Trip/Close

Close OSM

Trip OSM

CLOSE / TRIP

Yes

2

Control

Group 1 On

Group 1 Active

No Action

Pulse ON

Yes

3

Control

Group 2 On

Group 2 Active

No Action

Pulse ON

Yes

4

Control

Group 3 On

Group 3 Active

No Action

Pulse ON

Yes

5

Control

Group 4 On

Group 4 Active

No Action

Pulse ON

Yes

6

Control

Prot On

Protection ON

Protection OFF

Latch ON / Latch OFF

Yes

Disabled

Control

NPS On

NPS ON

NPS OFF


No

7

Control

EF On

Earth Fault ON

Earth Fault OFF


No

8

Control

SEF On

Sensitive Earth Fault ON

Sensitive Earth Fault OFF Under Voltage OFF


No


Yes

Over Voltage OFF Under Frequency OFF Over Frequency OFF

Latch ON / Latch OFF Latch ON / Latch OFF

Yes Yes


Yes


Yes

Yes

9

Control

UV On

Under Voltage ON

Disabled Disabled

Control Control

OV On UF On

Over Voltage ON Under Frequency ON

Disabled

Control

OF On

Over Frequency ON

10

Control

CLP On

Cold Load Pickup ON

11

Control

LL On

Live Line ON

Cold Load Pickup OFF Live Line OFF


Yes

12

Control

AR On

Auto Reclose ON

Auto Reclose OFF


Yes

13

Control

ABR On

Yes

Control

Pulse ON

Yes

Disabled

Control

Dnp3 Reset Communication Watchdog Timer Hot Line Tag On

Auto Backfeed Restoration OFF No Action


Disabled

Auto Backfeed Restoration ON Resets Communication Watchdog timer to its maximum value Hot Line Tag ON

Hot Line Tag OFF


Yes

Disabled

Control


Yes

Control

No Action


Yes

Disabled

Control

Sets Maximum Number of Trips to Lockout to 2 Sets Maximum Number of Trips to Lockout to 3 Short Sequence Mode ON

No Action

Disabled

79-2 Trips to Lockout 79-3 Trips to Lockout SSM On


Yes

Disabled

Control

DFT On

Disable Fast Trips is ON


Yes

Disabled

Control

Reset Binary Fault Targets

Resets to 0 the value in following points (note 1): Open(Prot), Open(OC1+), Open(OC2+), Open(OC3+), Open(OC1-), Open(OC2-), Open(OC3-), Open(EF1+), Open(EF2+), Open(EF3+), Open(EF1-), Open(EF2-), Open(EF3-), Open(SEF+), Open(SEF-), Open(OCLL), Open(EFLL), Open(UV1), Open(UV2), Open(UV3), Open(OV1), Open(OV2), Open(OF), Open(UF), Open(PhA), Open(PhB), Open(PhC), Open(PhN), Open(ABR AutoOpen), MNT Exceeded.

Short Sequence Mode OFF Disable Fast Trips is OFF No Action

Pulse ON

No, EF/SEF/ UV2/OV2




NOJA-522-06

Page 76 09-01-2014

NOJA-522-06 Recommended control type Pulse ON



Yes


Yes

Block Close

Maximum Number of Trips is ON Block Close is ON

Auto Change Over OFF Maximum Number of Trips is OFF Block Close is OFF


Yes

NPS On

NPS is ON

NPS is OFF


Yes

Erase Fault Counters Erase SCADA counters Erase energy meters Erase Oscillography Files Erase Interruption Counters and Duration Counters Erase Sag/Swell Counters and Duration Counters

Erase Fault Counters

No Action

Pulse ON

Yes

Erase SCADA counters

No Action

Pulse ON

Yes

Erase energy meters

No Action

Pulse ON

Yes

Erase Oscillography Files

No Action

Pulse ON

Yes

Erase Interruption Counters and Duration Counters

No Action

Pulse ON

Yes

Erase Sag/Swell Counters and Duration Counters

No Action

Pulse ON

Yes

Default DNP ID Disabled

Data group Control

Disabled

Control

ACO On

Disabled

Control

MNT On

Disabled

Control

Disabled

Control

14

Erase

16

Erase

15

Erase

18

Erase

19

Erase

20

Erase

Database ID Reset Trip Currents

Set = 1 Resets to 0 the value in following Anaput Points: Ia Trip, Ib Trip, Ic Trip, In Trip, I2 Trip Auto Change Over ON

Clear = 0 No Action

Erase

IO Modules (note 2) Disabled

Control

IO1 Output 1

Output ON

Output OFF


Yes

Disabled

Control

IO1 Output 2

Output ON

Output OFF


Yes

Disabled

Control

IO1 Output 3

Output ON

Output OFF


Yes

Disabled

Control

IO1 Output 4

Output ON

Output OFF


Yes

Disabled

Control

IO1 Output 5

Output ON

Output OFF


Yes

Disabled

Control

IO1 Output 6

Output ON

Output OFF


Yes

Disabled

Control

IO1 Output 7

Output ON

Output OFF


Yes

Disabled

Control

IO1 Output 8

Output ON

Output OFF


Yes

Disabled

Control

IO2 Output 1

Output ON

Output OFF


Yes

Disabled

Control

IO2 Output 2

Output ON

Output OFF


Yes

Disabled

Control

IO2 Output 3

Output ON

Output OFF


Yes

Disabled

Control

IO2 Output 4

Output ON

Output OFF


Yes

Disabled

Control

IO2 Output 5

Output ON

Output OFF


Yes

Disabled

Control

IO2 Output 6

Output ON

Output OFF


Yes

Disabled

Control

IO2 Output 7

Output ON

Output OFF


Yes

Disabled

Control

IO2 Output 8

Output ON

Output OFF


Yes

Disabled

Control

VAR1

Set Variable 1 True

Set Variable 1 False


Yes

Disabled

Control

VAR2

Set Variable 2 True



Yes

Disabled

Control

VAR3

Set Variable 3 True



Yes

Disabled

Control

VAR4

Set Variable 4 True



Yes

Disabled

Control

VAR5

Set Variable 5 True



Yes

Variables




NOJA-522-06

Page 77 09-01-2014

NOJA-522-06 Clear = 0 Set Variable 6 False

Recommended control type Latch ON / Latch OFF


Set Variable 7 True



Yes

Set Variable 8 True



Yes

Default DNP ID Disabled

Data group Control

Database ID VAR6

Set = 1 Set Variable 6 True

Disabled

Control

VAR7

Disabled

Control

VAR8



Each of the RC10 SCADA communications ports can be configured as either Local or Remote.



All controls from any source except for Trip Command are rejected if RC Local/Remote Mode does not match with Local/Remote Mode of Communication Port or IO/Relay Inputs/Logic Input.



When in Local Control mode, the status bits of all other CROB points are shown as offline.

Notes:

1. These point values are also reset to zero automatically when the recloser closes. This control is used to reset them to zero while open. 2. The following conditions are necessary to control IO Modules from SCADA: - IO mode is enabled in I/O settings; - IO Output# has Type equal to generic output or input in I/O settings; - IO faults are absent;




NOJA-522-06

Page 78 09-01-2014

NOJA-522-06 5.4

DEFINITION OF COUNTER/FROZEN COUNTER POINT LIST:



Note: the number of counters present in the device, and the maximum counter index, are available remotely using object Group 0 Variations 229 and 228.

Static (Steady-State) Object Number: Change Event Object Number: *) Request Function Codes ed :

20 22 1 (read), 7 (freeze), 8 (freeze noack) 9 (freeze and clear), 10 (freeze and clear, noack), 22 (assign class)

Static Variation reported when variation 0 requested: Change Event Variation reported when variation 0 requested:

6 (16-Bit Binary Counter without Flag) 1 (16-Bit Counter Change Event with Time)

Frozen Counters Static (Steady-State) Object Number: Change Event Object Number: Request Function Codes ed: Static Variation reported when variation 0 requested: Change Event Variation reported when variation 0 requested:

21 23 1 (read), 22 (assign class) 10 (16-Bit Frozen Binary without Flag) 6 (16-Bit Frozen Counter Event with Time)

Note: Counter points are always considered online and the on-line status bit is always set. No other status bits are ed for counter objects.

The value in the Default DNP ID column represents the default setting. This parameter is configurable between 0 and 255, individual points can be selected for mapping or disabled using CMS software Changes to class allocation arising from use of DNP3 function 22 are saved to volatile memory. Time stamps associated with Fault counter change events correspond to the time stamps appearing in the HMI or CMS CO Operations log.

Counter objects can be individually disabled by Object type for each counter.

*)

Request Functions Code 9 (freeze and clear) and 10 (freeze and clear, noack) are ed for SCADA Counters only.




NOJA-522-06

Page 79 09-01-2014


Data group

Valid Range

Resolution scale factor

Default Reporting Deadband

Default Class


Database ID

Description Overcurrent protection trips on A phase Overcurrent protection trips on B phase Overcurrent protection trips on C phase Neg. Phase Sequence protection trips Earth Fault protection trips Sensitive Earth Fault Protection Trips Under Voltage protection Trips Over Voltage protection Trips Under Frequency protection trips Over Frequency protection trips

0 to 65535

1

4

1

Yes

0 to 65535

1

4

1

No

0 to 65535

1

4

1

No

0 to 65535

1

4

1

No

0 to 65535

1

4

1

No

0 to 65535

1

4

1

No

0 to 65535

1

2

1

Yes

0 to 65535

1

0

0

Yes

0 to 65535

1

0

0

Yes

0 to 65535

1

0

0

Yes

Number of Close – Open operations Mechanical wear consumed; expressed as a percentage Maximum vacuum Interrupter wear consumed on any one phase; expressed as a percentage

0 to 65535

1

20

1

Yes

0 to 100%

1

10%

1

Yes

0 to 100%

1

10%

1

Yes

A phase total forward energy

0 to 4294967295 kVAh

1

0

0

Yes

Fault Counters 0

Indication

OC A Trips

1

Indication

OC B Trips

2

Indication

OC C Trips

Disabled

Indication

NPS Trips

3

Indication

EF Trips

4

Indication

SEF Trips

5

Indication

UV Trips

Disabled

Indication

OV Trips

Disabled

Indication

UF Trips

Disabled

Indication

OF Trips

Lifetime Counters 6

Indication

CO Total

7

Indication

Mechanical Wear

8

Indication

Max phase Wear

Energy Meters Disabled

Indication

A +kVAh




NOJA-522-06

Page 80 09-01-2014

NOJA-522-06 Default DNP ID Disabled

Data group Indication

Database ID B +kVAh

Description B phase total forward energy

Disabled

Indication

C +kVAh

C phase total forward energy

Disabled

Indication

A +kVArh

Disabled

Indication

B +kVArh

Disabled

Indication

C +kVArh

Disabled

Indication

A -kVAh

A phase reactive forward energy B phase reactive forward energy C phase reactive forward energy A phase total reverse energy

Disabled

Indication

B -kVAh

B phase total reverse energy

Disabled

Indication

C -kVAh

C phase total reverse energy

Disabled

Indication

A -kVArh

Disabled

Indication

B -kVArh

Disabled

Indication

C -kVArh

9

Indication

+kVAh

Disabled

Indication

+kVArh

10

Indication

-kVAh

Disabled

Indication

-kVArh

Disabled

Indication

A +kWh

A phase reactive reverse energy B phase reactive reverse energy C phase reactive reverse energy Three phase total forward energy Three phase reactive forward energy Three phase total reverse energy Three phase reactive reverse energy A phase active forward energy

Disabled

Indication

B +kWh

B phase active forward energy

Disabled

Indication

C +kWh

C phase active forward energy




Valid Range 0 to 4294967295 kVAh 0 to 4294967295 kVAh 0 to 4294967295 kVArh 0 to 4294967295 kVArh 0 to 4294967295 kVArh 0 to 4294967295 kVAh 0 to 4294967295 kVAh 0 to 4294967295 kVAh 0 to 4294967295 kVArh 0 to 4294967295 kVArh 0 to 4294967295 kVArh 0 to 4294967295 kVAh 0 to 4294967295 kVArh 0 to 4294967295 kVAh 0 to 4294967295 kVArh 0 to 4294967295 kWh 0 to 4294967295 kWh 0 to 4294967295 kWh

Resolution scale factor 1

Default Reporting Deadband 0

Default Class 0

1

0

0

No

1

0

0

Yes

1

0

0

No

1

0

0

No

1

0

0

Yes

1

0

0

No

1

0

0

No

1

0

0

Yes

1

0

0

No

1

0

0

No

1

100000 kVAh

3

No

1

0

0

No

1

100000 kVAh

3

No

1

0

0

No

1

0

0

Yes

1

0

0

No

1

0

0

No

NOJA-522-06

Single Phase Recloser No

Page 81 09-01-2014



Database ID A -kWh

Description A phase active reverse energy

Disabled

Indication

B -kWh

B phase active reverse energy

Disabled

Indication

C -kWh

C phase active reverse energy

Disabled

Indication

+kWh

Disabled

Indication

-kWh

Three phase active forward energy Three phase active reverse energy

Valid Range 0 to 4294967295 kWh 0 to 4294967295 kWh 0 to 4294967295 kWh 0 to 4294967295 kWh 0 to 4294967295 kWh



Default Class 0


1

0

0

No

1

0

0

No

1

0

0

No

1

0

0

No

SCADA Counters Disabled

Indication

Call Drop outs

Disabled

Indication

Calls Failed

11

Indication

Tx Frames

12

Indication

Rx Frames

13

Indication

Length errors

14

Indication

CRC errors

Disabled

Indication

Dnp3 Communication Watchdog Timeout

The number of modem calls where RC10 did not initiate hanging up. Increments when Slave does not connect to the base station modem. Transmitted frame count Received frame count Frame length error count Frame CRC error count Number of times communication Watchdog timer timed out

0 to 4294967295

1

0

0

Yes

0 to 4294967295

1

0

0

Yes

0 to 4294967295 0 to 4294967295 0 to 4294967295 0 to 4294967295 0 to 65535

1

100

0

Yes

1

100

0

Yes

1

100

0

Yes

1

100

0

Yes

1

0

0

Yes

Maximum Demand A phase current today Maximum Demand B phase current today Maximum Demand C phase current today

0 to 16000 A

1

0

0

Yes

0 to 16000 A

1

0

0

No

0 to 16000 A

1

0

0

No

Maximum Demand Counters Disabled

Indication

la MDI Today

Disabled

Indication

lb MDI Today

Disabled

Indication

lc MDI Today

(1)

(1)

(1)




NOJA-522-06

Page 82 09-01-2014



Disabled

Indication

lb MDI (1) Yesterday

Disabled

Indication

lc MDI (1) Yesterday

Disabled

Indication

la MDI Last (1) Week

Disabled

Indication

lb MDI Last (1) Week

Disabled

Indication

lc MDI Last (1) Week

Database ID la MDI (1) Yesterday

Description Maximum Demand A phase current yesterday Maximum Demand B phase current yesterday Maximum Demand C phase current yesterday Maximum Demand A phase current last week Maximum Demand B phase current last week Maximum Demand C phase current last week



Default Class 0

0 to 16000 A

1

0

0

No

0 to 16000 A

1

0

0

No

0 to 16000 A

1

0

0

Yes

0 to 16000 A

1

0

0

No

0 to 16000 A

1

0

0

No

Valid Range 0 to 16000 A


Note: Change event generation: Change event is generated under conditions: X = Last Reported Value Y = New Value D = Deadband Value Y > (X + D) or Y < (X - D)

Note 1: Maximum Demand Indication (MDI) is implemented only as Protocol Points and report only values of currents (Ia, Ib, Ic and In). The RMS value of current in phases A, B, C and In are averaged in accordance with Load Profile configuration. Load Profile is configurable for the intervals of 1/2/5/10/15/30/60/120 minutes. For customer, to have average MDI time of 15 minutes, the Load Profile time must be set to 15 minutes. All of the MDI values are volatile and will be reset back to zero when the controller is reset. The MDI records are reported as for TODAY, YESTERDAY and LAST WEEK. Definitions of these are: • The TODAY Load Profile is monitored for the highest value in the records from last midnight till now. • The YESTERDAY Load Profile is monitored for the highest value in the records for the 24 hours till last midnight. • The LAST WEEK Load Profile is monitored for the highest record during the last 7 days till last midnight. The values for record types (YESTERDAY and LAST WEEK) are updated only on expiration of the relevant period. The value for record type TODAY is updated when a new maximum for TODAY is detected. DNP3 Device Profile Document Vendor Name:



NOJA-522-06

Page 83 09-01-2014

NOJA-522-06 5.5

DEFINITION OF ANAPUT POINT LIST:



Note: the number of anaputs present in the device, and the maximum anaput index, are available remotely using object Group 0 Variations 233 and 232.

The following table lists Anaputs (Object 30). This implementation uses fixed deadband reporting, the value in the “Default Deadband” column represents the absolute amount by which the point must change before an analog change event will be generated. The value in the “Default Class” column represents the class (1, 2, 3, or none) in which detected change events will be reported. Only the default values for these items are documented here because the values may change in operation due to either local (-interface) or remote (through DNP) configuration control. Changes to class allocation arising from use of DNP3 function 22 are saved to volatile memory. Changes to reporting deadband arising from use of DNP3 function 2 are saved to volatile memory. Static (Steady-State) Object Number:

30

Change Event Object Number:

32

Reporting Deadband Object Number:

34

Request Function Codes ed: 1 (read), 2 (write, deadbands only), 22 (assign class) Default Static Variation reported when variation 0 requested: Input).

(Note 1) 2 (16-Bit Analog

Default Change Event Variation reported when variation 0 requested: Event with Time)

(Note 1) 3 (Analog Change

Reporting Deadband Variation reported when variation 0 requested: Deadband)

1 (16-Bit Reporting

Status bits ed: over range, local forced data Note 1: The actual variation reported in response to a variation 0 request can be configured on a per-point basis.

Note: Anaputs are always considered online and the on-line status bit is always set. Resolution scale factor shows on what coefficient it is necessary to multiply the obtained value to receive true. Anaput change events are detected by the IED at the time they occur and are not subject to a scan rate. Time stamps associated with Analog change events depend on the ana question. Measurement values are updated every 16 cycles of power frequency; a change event is generated if deadband is exceeded for any point. Protection related analog change events have time stamps that correspond to the related CO Operations event. DNP3 Device Profile Document Vendor Name:



NOJA-522-06

Page 84 09-01-2014

NOJA-522-06 The value in the Default DNP ID column represents the default setting. This parameter is configurable between 0 and 255, individual points can be selected for mapping or disabled using CMS software. The values in the Range column represent analog values that may be transmitted depending on the ratings of the OSM connected to the RC cubicle. RC measurement accuracy is defined in the Specifications section of the OSM Manual.

Default DNP ID

Data group

Database ID

Description

Valid Range



Default Class


1

10 A

1

Yes

1

10 A

1

No

1

10 A

1

No

0.001

0 kV

0

Yes

0.001

0 kV

0

No

0.001

0 kV

0

No

0.001

0 kV

0

Yes

0.001

0 kV

0

No

0.001

0 kV

0

No

0.001

0.5 kV

1

No

0.001

0.5 kV

1

No

0.001

0.5 kV

1

No

0.001

0 kV

0

No

0.001

0 kV

0

No

0.001

0 kV

0

No

1

1A

1

No

1

1A

1

No

1

0 kVA

0

Yes

Measured Data 0

Indication

Ia

A phase current

1

Indication

Ib

B phase current

2

Indication

Ic

C phase current

Disabled

Indication

Ua

Disabled

Indication

Ub

Disabled

Indication

Uc

Disabled

Indication

Ur

Disabled

Indication

Us

Disabled

Indication

Ut

3

Indication

Uab

4

Indication

Ubc

5

Indication

Uca

Disabled

Indication

Urs

Disabled

Indication

Ust

Disabled

Indication

Utr

Disabled

Indication

I2

Phase to earth voltage Ua Phase to earth voltage Ub Phase to earth voltage Uc Phase to earth voltage Ur Phase to earth voltage Us Phase to earth voltage Ut Line to Line voltage Uab Line to Line voltage Ubc Line to Line voltage Uca Line to Line voltage Urs Line to Line voltage Ust Line to Line voltage Utr Neg. Phase Sequence

6

Indication

In

Neutral current

Disabled

Indication

A kVA

A phase kVA




0 to 16,000 A 0 to 16,000 A 0 to 16,000 A 0 to 30.0 kV 0 to 30.0 kV 0 to 30.0 kV 0 to 30.0 kV 0 to 30.0 kV 0 to 30.0 kV 0 to 38.0 kV 0 to 38.0 kV 0 to 38.0 kV 0 to 38.0 kV 0 to 38.0 kV 0 to 38.0 kV 0 to 16,000 A 0 to 16,000 A 0 to 65535 kVA NOJA-522-06

Page 85 09-01-2014



Database ID B kVA

Description B phase kVA

Disabled

Indication

C kVA

C phase kVA

Disabled

Indication

A kW

A phase kW

Disabled

Indication

B kW

B phase kW

Disabled

Indication

C kW

C phase kW

Disabled

Indication

A kVAr

A phase kVAr

Disabled

Indication

B kVAr

B phase kVAr

Disabled

Indication

C kVAr

C phase kVAr

7

Indication

kVA

Three phase kVA

8

Indication

kW

Three phase kW

9

Indication

kVAr

Three phase kVAr

10

Indication

F ABC

ABC side frequency

Disabled

Indication

F RST

RST side frequency

11

Indication

PF

Disabled

Indication

A PF

Disabled

Indication

B PF

Disabled

Indication

C PF

12

Indication

Phase seq. ABC

Three phase power factor A phase power factor B phase power factor C phase power factor Phase sequence from ABC side ABC = 1

Valid Range 0 to 65535 kVA 0 to 65535 kVA 0 to 65535 kW 0 to 65535 kW 0 to 65535 kW 0 to 65535 kVAr 0 to 65535 kVAr 0 to 65535 kVAr 0 to 65535 kVA 0 to 65535 kW 0 to 65535 kVAr 46.00 to 65.00 Hz 46.00 to 65.00 Hz 0.00 to 1.00 0.00 to 1.00 0.00 to 1.00 0.00 to 1.00 0 to 2


Default Reporting Deadband 0 kVA

Default Class 0


1

0 kVA

0

No

1

0 kW

0

Yes

1

0 kW

0

No

1

0 kW

0

No

1

0 kVAr

0

Yes

1

0 kVAr

0

No

1

0 kVAr

0

No

1

500 kVA

2

No

1

500 kW

2

No

1

500 kVAr

2

No

0.001

0.1 Hz

1

Yes

0.001

0 Hz

0

Yes

0.001

1

1

No

0.001

0

0

Yes

0.001

0

0

No

0.001

0

0

No

1

1

1

No

1

0

0

No

ACB = 0 Unresolved = 2 Disabled

Indication

Phase seq.




Phase sequence

0 to 2 NOJA-522-06

Page 86 09-01-2014


Data group

Database ID RST

Description from RST side

Valid Range



Default Class


RST = 1 RTS = 0 Unresolved = 2 Disabled

Indication

Phase Configuration

Disabled

Indication

LGVT Ia

(9)

Disabled

Indication

LGVT Ib

(9)

Disabled

Indication

LGVT Ic

(9)

Disabled

Indication

DE OC

Disabled

Indication

DE NPS

Disabled

Indication

DE EF

Phases Configured as ABC = 0, ACB = 1, BCA = 2, CAB = 3, BAC = 4, CBA = 5 A phase current value recorded before Recloser operated. B phase current value recorded before Recloser operated. C phase current value recorded before Recloser operated.

1 to 5

1

0

0

No

0 to 16,000 A

1

10A

1

Yes

0 to 16,000 A

1

10A

1

No

0 to 16,000 A

1

10A

1

No

OC power flow direction Positive = 0 Negative = 1 Unresolved = 2 NPS power flow direction Positive = 0 Negative = 1 Unresolved = 2 EF Power flow direction Positive = 0

0 to 2

1

0

0

Yes

0 to 2

1

0

0

Yes

0 to 2

1

0

0

No

0 to 2

1

0

0

No

0 to 16,000 A 0 to 16,000 A

1

0A

0

Yes

1

0A

0

No

Protection

Negative = 1 Unresolved = 2 Disabled

Indication

DE SEF

SEF Power flow direction Positive = 0 Negative = 1

Disabled

Indication

Ia max Trip

Disabled

Indication

Ib max Trip




Unresolved = 2 Maximum phase A current prior to any OCEF element trip Maximum phase B current prior to any OCEF element trip

NOJA-522-06

Page 87 09-01-2014



Database ID Ic max Trip

Disabled

Indication

I2 max Trip

Disabled

Indication

In max Trip

Disabled

Indication

UV min Trip

Disabled

Indication

OV max Trip

Disabled

Indication

UF min Trip

Disabled

Indication

OF max Trip

Disabled

Indication

Ia Trip

Disabled

Indication

Ib Trip

Disabled

Indication

Ic Trip

Disabled

Indication

I2 Trip




Description Maximum phase C current prior to any OCEF element trip Maximum I2 current prior to any NPS element trip Maximum In current prior to any EF element trip Minimum voltage prior to any UV elements trip Maximum voltage prior to any OV elements trip Minimum frequency prior to UF element trip Maximum frequency prior to OF element trip Value of current in A phase at the time when Trip command is issued. Value is stored until next protection trip or when cleared by command from Master Value of current in B phase at the time when Trip command is issued. Value is stored until next protection trip or when cleared by command from Master Value of current in C phase at the time when Trip command is issued. Value is stored until next protection trip or when cleared by command from Master Value of current at the time when Trip command is issued. Value is


Default Reporting Deadband 0A

Default Class 0

1

0A

0

No

1

0A

0

No

0.001

0kV

0

Yes

0 to 38.0kV

0.001

0kV

0

Yes

46.00 to 65.00 Hz 46.00 to 65.00 Hz 0 to 16,000 A

0.001

0Hz

0

Yes

0.001

0Hz

0

Yes

1

0A

0

Yes

0 to 16,000 A

1

0A

0

No

0 to 16,000 A

1

0A

0

No

0 to 16,000 A

1

0A

0

No

Valid Range 0 to 16,000 A 0 to 16,000 A 0 to 16,000 A 0 to 38.0kV

NOJA-522-06


Page 88 09-01-2014


Data group

Database ID

Disabled

Indication

In Trip

Description stored until next protection trip or when cleared by command from Master Value of residual current at the time when Trip command is issued. Value is stored until next protection trip or when cleared by command from Master



Default Class

0 to 16,000 A

1

0A

0

No

1

0

0

Yes

0.01

1V

1

Yes

0.01

0.5A

1

Yes

1

10

1

Yes

0.001

0V

1

Yes

Valid Range


Lifetime Counters Disabled

Indication

CO Total

Number of Close – Open Operations

0 to 65535 0.00 40.95 -4.00 to +4.00 A 0 to 100% 0.00 40.95

UPS Status 13

Indication

Ubt

Battery voltage

14

Indication

Ibt

15

Indication

Cbt

Disabled

Indication

Ubt Scaled

Battery charge current Battery residual capacity Battery voltage (Scaled)

Notes: 1. Data representation: (0 to 65535) – non-negative integer number occupies 2 bytes, except for Data base ID Ibt (–32768 to 32767) (0 to 4294967296) – non-negative integer number occupies 4 bytes. 2. Step value in Valid Range is equal 1*Resolution scale factor. 3. Power values (single and three phase kVA, kVAr and kW) have a maximum range of 65535. Values higher than this are represented as 65535 and the ‘Over-range’ status bit is set to 1. 4. If there is a situation when it is not possible to calculate power factor or frequency, a value equal to 0xFFFF is reported. 5. Valid Range is given as supplemental information. 6. Change event generation: Change event is generated under conditions: X = Last Reported Value; Y = New Value; D = Deadband Value; Y > (X + D) or Y < (X - D)




NOJA-522-06

Page 89 09-01-2014

NOJA-522-06 7. The Ia max Trip, Ib max Trip, Ic max Trip, I2 max Trip, In max Trip, UVmin Trip, OVmax Trip, UFmin Trip, OFmax Trip values are updated when a new record is generated during a CO operation. Only the point related to the phase that caused the trip is updated. 8. All the Ia Trip, Ib Trip, Ic Trip and In Trip analogs are updated when a trip occurs. They can be reset to zero using the “Reset Trip current Values” binary output point. 9. Last Good Value Trapped (LGVT) measured data is implemented only as Protocol Points (Analogue Input Points for DNP3 and Measured Values for IEC 60870-5-101/104) and report only values of phase currents (Ia, Ib, Ic). LGVT is calculated as 1 minute average value. The LGVT will be frozen at its previous 1-minute average value while the current is 0 Amps or Pickup_LSD flag is set.




NOJA-522-06

Page 90 09-01-2014

NOJA-522-06 5.6

DEFINITION OF ANALOG OUTPUT STATUS/ANALOG OUTPUT CONTROL BLOCK POINT LIST:

Fixed, list shown in table below Configurable (current list may be shown in table below) Other, explain – Not ed

List all addressable points. Points that do not exist (for example, because an option is not installed) shall be omitted from the table. Note: the number of analog outputs present in the device, and the maximum analog output index, are available remotely using object Group 0 Variations 221 and 220.




NOJA-522-06

Page 91 09-01-2014

NOJA-522-06 5.7

DEFINITION OF FILE NAMES THAT MAY BE READ OR WRITTEN:




Fixed, list shown in table below Configurable(current list may be shown in table below) Other, explain – Not ed

NOJA-522-06

Page 92 09-01-2014

NOJA-522-06 DEFINITION OF OCTET STRING POINT LIST:

5.8



This object provides for HMI and the version and serial number strings. Default DNP ID

Database ID

Max string length

Permitted characters A – Z; 0 – 9; space

0

HMI

4

1

Relay Version String

40

A – Z; a – z; 0 – 9; space

Disabled

Relay Serial Number

13

A – Z; a – z; 0 – 9; Space

Disabled

Relay Hardware Version

40

A – Z; a – z; 0 – 9; Space

Disabled

Relay FPGA version

40

A – Z; a – z; 0 – 9; Space

Disabled

SIM Hardware Version

40

A – Z; a – z; 0 – 9; Space

Disabled

SIM Software Version

40

A – Z; a – z; 0 – 9; Space

Disabled

SIM Serial Number

13

A – Z; a – z; 0 – 9; Space

Disabled

Serial Number

13

A – Z; a – z; 0 – 9; Space

Disabled

HMI Version

40

A – Z; a – z; 0 – 9; Space

Disabled

Hardware Version

40

A – Z; a – z; 0 – 9; Space

Disabled

Software Version

40

A – Z; a – z; 0 – 9; Space

Disabled

OSM Serial Number

13

A – Z; a – z; 0 – 9; Space

Disabled

OSM Model Number

40

Disabled

IO1 Serial Number

13

A – Z; a – z; 0 – 9; Space A – Z; a – z; 0 – 9; Space

Disabled

13

A – Z; a – z; 0 – 9; Space

Disabled

IO2 Serial Number IO1 Software Version

40

A – Z; a – z; 0 – 9; Space

Disabled

IO2 Software Version

40

A – Z; a – z; 0 – 9; Space

Disabled

IO1 Hardware Version

40

A – Z; a – z; 0 – 9; Space

Disabled

IO2 Hardware Version

40

A – Z; a – z; 0 – 9; Space




NOJA-522-06

Page 93 09-01-2014

NOJA-522-06 5.9

DEFINITION OF VIRTUAL TERMINAL PORT NUMBERS:





Fixed, list shown in table below Configurable (current list may be shown in table below) Other, explain – Not ed.

NOJA-522-06

Page 94 09-01-2014

NOJA-522-06 5.10

DEFINITION OF DATA SET PROTOTYPES:

List of all data set prototypes. The following table is repeated for each Data Set Prototype defined.

Fixed, Data Set Prototypes are shown in table below Configurable, list methods: (a list of currently defined Data Set Prototypes may be shown in tables below) Other, explain – Not ed

Note: the numbers of data set prototypes known to the device are available remotely using the protocol object Group 0 Variations 212 and 213.




NOJA-522-06

Page 95 09-01-2014

NOJA-522-06 5.11

DEFINITION OF DATA SET DESCRIPTORS:

List of all data set descriptors. The following tables are repeated for each Data Set Descriptor defined. Note: the numbers of data sets known to the device are available remotely using the protocol object Group 0 Variations 214 and 215.




Fixed, Data Set Descriptors are shown in table below Configurable (current list may be shown in table below) Other, explain – Not ed

NOJA-522-06

Page 96 09-01-2014

NOJA-522-06 5.12

DATA SET DESCRIPTOR – POINT INDEX ATTRIBUTES

The following table is optional and correlates data set elements to point indexes of standard DNP3 Data Objects. The element number below refers to the position in the present value (object 87) or event (object 88) data set and will not match the element number in the data set descriptor or data set prototype tables above. Duplicate this table for each Data Set Descriptor defined

Not ed.




NOJA-522-06

Page 97 09-01-2014

NOJA-522-06

6 INTERNAL INDICATIONS The following table lists Internal Indications (IINs), and the conditions that would cause them. Standard DNP3 IINs are reported in every response message. This table lists standard DNP3 IINs. Internal Indications Object Number: 80 Request Function Codes ed: 1 (read), 2 (write) Default Variation reported when variation 0 requested: 1 Poi nt Descriptions and Conditions Ind ex 0 IIN1-0 All Stations – set after a broadcast message (any message using a destination address of 0xfff0 or above) has been received. Does not indicate an error condition. 1 IIN1-1 Class 1 event data available. Can be set at any time and does not indicate an error condition. 2 IIN1-2 Class 2 event data available. Can be set at any time and does not indicate an error condition. 3 IIN1-3 Class 3 event data available. Can be set at any time and does not indicate an error condition. 4 IIN1-4 Time synchronization required. Can be set at any time and does not indicate an error condition. 5 IIN1-5 Local mode. Set if the device is in an operating mode that will block commands from the Master. (RC10 communications ports can be configured as either a local or remote ) 6 IIN1-6 Device Trouble. Set if a device malfunction is detected refer to ‘Malfunctions’ section of Binary Inputs and/or the manual for a description of possible causes. 7 IIN1-7 Device restarts. Set only under specific conditions. Does not indicate an error condition. 8 IIN2-0 Function Unknown. Generally means that the function code (octet 2 of the request header) cannot be processed. 9 IIN2-1 Object Unknown. Generally means that the function code could be processed but the object group / variation could not be processed. 10 IIN2-2 Parameter Error. Generally indicates that both the function code and object group / variation could be processed but that the qualifier / range field is in error. 11 IIN2-3 Buffer Overflow. Indicates that an event buffer has overflowed, and that change events, of at least one type, have been lost. 12 IIN2-4 Already Executing. NOT ED 13 IIN2-5 Bad configuration. 14 IIN2-6 Reserved. Always 0. 15 IIN2-7 Reserved. Always 0.




NOJA-522-06

Writabl e? No No No No No No

No Yes No No No No NA No NA NA

Page 98 09-01-2014

NOJA-522-06

7 BUFFER SIZE Maximum number of events held in volatile RAM buffers: object 2 (binary) object 22 (counters) object 23 (frozen counters) object 32 (analog)




- 500 events; - 400 events; - 350 events; - 350 events.

NOJA-522-06

Page 99 09-01-2014

NOJA-522-06

8 DNP3 SETTINGS Yes

HMI (Control) Yes

never

Yes

No

3s

Yes

No

2

Yes

No

64 to 292 octets step size 1

292

Yes

No

On (Ticked) Off (Unticked)

Off

Yes

No

0 to 3600s

5s

Yes

No

Yes

No

Name

Explanation

Range

Link Layer Slave Address Link Layer Confirmation Mode Link Layer Confirmation Timeout

The DNP Link address of this device.

0 to 65534 Step size 1 Never, Sometimes, Always 0 to 60s

Link Layer Maximum Retries

This parameter is used to determine if or when the device may request confirmation from the DNP master of data link layer frames transmitted to the master. Timeout value, in seconds, used to wait for DNP master to confirm a previously transmitted link layer frame with a request for confirmation. This value is independent of Appl Cf Timeout; if link confirmations are being used (see Link Cf Mode), the application confirmation timer is not started until a link confirmation is received. The maximum number of times this device will re-transmit a link layer frame for which a confirmation had been requested but not received within Link Cf Timeout. Note that this number is in addition to the initial attempt to transmit the frame; i.e., if the value of this parameter is 2, then an unsuccessful transmission will send a total of 3 identical frames. Maximum size of frame to transmit

Link Layer Maximum Transmitted Frame Size Link Layer Specify whether or not to validate the master address in Validate Master received frames. DNP3 frames Address contain both a master address field and a slave address field. If OFF then TMW DNP3 SCL will not validate the master address and frames whose slave address matches a configured slave session will be accepted. Setting this to ON requires both master and slave addresses to match a local slave session before the frame is accepted. Application Amount of time, in seconds, after a select command is Layer received before which an operate command must be SBO Timeout received. If this time is exceeded, the select will be aborted (SBO = Select and any subsequent operate will not be executed. Before Operate) Application This parameter is used to determine if or when the device Layer may request confirmation from the DNP master of application Confirmation layer frames transmitted to the master. Mode




NOJA-522-06

Default value 5

CMS

Step size 1s

0 to 32767 Step size 1

Step Size 1s

Events (only Events when and Mult reporting event data) Events and Multi-Packets (when reporting events or multi fragment messages)

Page 100 09-01-2014

NOJA-522-06

Yes

HMI (Control) No

Yes

No

0 to 65530ms 5000ms Step size 1 ms

Yes

No

The time, in ms, encoded in a response to a request from a 0 to 65530ms 1000ms master for a warm restart. The master is thereby notified to Step size 1 wait this amount of time after receiving the response before it ms can resume polling this device.

Yes

No

Name

Explanation

Range

Application Layer Confirmation Timeout

Timeout value, in seconds, used to wait for DNP master to confirm a previous response to the master containing a request for confirmation. This value is independent of Link Cf Timeout; if link confirmations are being used (see Link Cf Mode), the application confirmation timer is not started until a link confirmation is received. This parameter is also used as part of the control for when an unconfirmed unsolicited response can be re-generated and re-transmitted. See Unsol Retry Delay. To ensure correct operation of confirm timeouts if Link Cf Mode is set to ‘sometimes’ or always’ the RC10 checks that Appl Cf Timeout >= ((Link Max Retries + 1) x Link Cf TO x 7). If the enters a value less than this the RC10 will overwrite it with the above value. The amount of time, in minutes, after a DNP master executes a time synchronization with this device before this device sets the “need time” Internal Indication (IIN) bit to request another time synchronization. This value indicates the rate at which the internal clock of this device becomes out-of-sync with the master’s clock. If this parameter is set to 0, the “need time” IIN bit will never be set. The time, in ms, encoded in a response to a request from a master for a cold restart. The master is thereby notified to wait this amount of time after receiving the response before it can resume polling this device.

0 to 3600s

Application Layer Need Time Delay

Application Layer Cold Restart Delay Application Layer Warm Restart Delay

Unsolicited Response

If On, unsolicited responses are permitted; if Off, they are not. If permitted, the device will transmit an initial null unsolicited response, and will continue to send it until an application layer confirmation of it is received from the DNP Master device. From that point on, the DNP Master must issue an “unsolicited enable” request message for one or more of the three event classes of data (class 1, 2, or 3) before any more unsolicited response messages will be transmitted. If false, then “unsolicited enable” and “unsolicited disable” messages from the DNP Master device will not be allowed – a “BAD CONFIGURATION” Internal Indication (IIN) response will be returned. Unsolicited Specifies the DNP link address destination (a DNP master) Response of unsolicited responses. If unsolicited responses are Master Address enabled (see Unsolicited), then all unsolicited response messages, including the initial null unsolicited response, are transmitted to this address at startup.




NOJA-522-06

Default value 84s

CMS

Step Size 1s

0 to 69120 min

1440 min

Step Size 1min

On (Ticked) Off (Unticked)

Off

Yes

Yes

0 to 65534

3

Yes

Yes

Step Size 1

Page 101 09-01-2014

NOJA-522-06 Name

Explanation

Range

Unsolicited Response Retry Delay

This parameter specifies the minimum amount of time between unsuccessfully confirmed unsolicited responses. If an unsolicited response is not confirmed within Appl Cf Timeout, this parameter controls how soon another unsolicited response will be sent. If this parameter is zero or less than Appl Cf Timeout, the "retry" unsolicited response will be sent as soon as Appl Cf Timeout expires. During the time set by Appl Cf Timeout, any received read request received from the DNP Master device will be postponed until after Appl Cf Timeout has expired. If multiple read requests are received, only the last read request would be postponed; the previous read-requests will be ignored entirely. Once the number of retries is equal to Unsol Retries, the interval between retries is then controlled by Unsol Offline Interval, not Unsol Retry Delay. The maximum number of times this device will re-transmit an unsolicited response without receiving a confirmation from a Master at an interval defined by Unsol Retry Delay. Once this value is reached, the unsolicited response will continue to be retransmitted but at a potentially different interval defined by Unsol Offline Interval. If an unsolicited response has been retried Unsol Max Retries times without a confirmation then this parameter defines the time interval between unsolicited retries from that point forward. It allows the interval between retries to be increased if no confirmation is being received while still allowing an infinite number of unsolicited retries. Specify the initial/new state of the unsolicited event mask. This mask is used to determine which event class(es) will generate unsolicited responses. According to the DNP3 Guide, unsolicited responses should be disabled until an 'Enable Unsolicited Response' request is received from the master. Hence this value should generally be 0, but some masters do not generate the 'Enable Unsolicited Response' message in which case they must be enabled here.

0 to 86400s

Unsolicited Response Retries

Unsolicited Response Offline Interval

Unsolicited Response Mask Class 1 Class 2 Class 3

Unsolicited Response Events Class 1 Class 2 Class 3

Used to specify conditions under which an unsolicited response is generated. For each class, if the number of events occurring for that class meets or exceeds this value, then an unsolicited response will be generated (as long as the DNP Master device has enabled the class -- see Unsolicited). Note that other conditions may cause an unsolicited response to be generated – see C1, C2, C3 Delay.




NOJA-522-06

Default value 60s

Yes

HMI (Control) No

255

Yes

No

300s

Yes

No

0x00 Yes (Unsolicite d for class 1, 2, 3 disabled)

No

3 5 10

No

CMS

Step Size 1s

0 to 255 Step Size 1

0 to 86400s Step Size 1s

(0x00 –0x07) Any combination of 0x01 (Unsolicited for class 1 enabled) 0x02 (Unsolicited for class 2 enabled) 0x04 (Unsolicited for class 3 enabled) 1 to 255 Step Size 1

Yes

Page 102 09-01-2014

NOJA-522-06 Name

Explanation

Unsolicited Response Delay Class 1 Class 2 Class 3

Used to specify conditions under which an unsolicited response is generated. For each class, if the amount of time since an event has occurred for that class meets or exceeds this value, then an unsolicited response will be generated (as long as the DNP Master device has enabled the class –see Unsolicited). If the value for this parameter is 0 for a class, then this parameter is disabled for that class, and only C1, C2, C3 Events controls conditions under which will generate an unsolicited response for that class. Note that other conditions may cause an unsolicited response to be generated – see C1, C2, C3 Delay. Communication If the protocol is not polled within a set time period then Watchdog the external supply will be reset. This timer is reset whenever Poll Timeout protocol is polled. This timer overrides the External Load Reset Timer. Communication If the binary control is not activated within a set time Watchdog period then the external supply will be reset. This timer is Binary Control reset whenever allocated binary control point is modified. This timer overrides the External Load Reset Timer. SCADA Time Used to set internal clock to Local or GMT/UTC.




Step Size 1s

Default value 3s 5s 10s

0 to 86400s

60 min

Yes

No

Step Size 1min 0 to 86400s

60 min

Yes

No

GMT/UTC

Yes

No

Range

NOJA-522-06

0 to 86400s

Step Size 1min Local/ GMT/UTC

Yes

HMI (Control) No

CMS

Page 103 09-01-2014

NOJA-522-06 STATIC AND EVENT OBJECT DEFAULT VARIATIONS

8.1

The default variation is used whenever variation 0 is requested and in response to class polls. The RC10 allows per-point individual configuration of default variation. In addition, the reporting mode of anaput events may be specified for variations that do not include a timestamp. The reporting mode may be either: -

Report All: Which will create one event object for every event that has occurred between responses.

-

Report Last: Which will have a maximum of one event object for each point in each response, the object will represent the most recent event.

Name

Explanation

Binary Input Object 01

Specifies the default variation for object 01, binary input. The default variation is used whenever variation 0 is requested, and in responses to class polls. Binary This value specifies the default variation for Input object 02, binary input change events. The Object 02 default variation is used whenever variation 0 is requested, and in responses to class polls. Binary Output This value specifies the default variation for Object 10 object 10, binary output. The default variation is used whenever variation 0 is requested, and in responses to class polls. Binary Counter This value specifies the default variation for Object 20 object 20, binary (running) counters. The default variation is used whenever variation 0 is requested, and in responses to class polls.

Binary Counter Object 21

This value specifies the default variation for object 21, frozen counters. The default variation is used whenever variation 0 is requested, and in responses to class polls.


This value specifies the default variation for object 22, binary (running) counter change events. The default variation is used whenever variation 0 is requested, and in responses to class polls.




Default value 2

CM S Yes

HMI (Control) No

1 (without time), 2 (with time) 3 (with relative time)

2

Yes

No

1 (without status), 2 (with status)

2

Yes

No

1 (32-bit binary counters with status) 2 (16-bit binary counters with status) 5 (32-bit binary counters without status) 6 (16-bit binary counters without status) 255 (disabled) 1 (32-bit frozen counters with status) 2 (16-bit frozen counters with status) 5 (32-bit frozen counters with time) 6 (16-bit frozen counters with time) 9 (32-bit frozen counters without status) 10 (16-bit frozen counters without status) 255 (disabled) 1 (32-bit binary counters without time) 2 (16-bit binary counters without time) 5 (32-bit binary counters with time) 6 (16-bit binary counters with time) 255 (disabled)

5

Yes

No

9

Yes

No

5

Yes

No

Range 1 (without status), 2 (with status)

NOJA-522-06

Page 104 09-01-2014

NOJA-522-06 Default value 5

Name

Explanation

Range


This value specifies the default variation for object 23, frozen counter events. The default variation is used whenever variation 0 is requested, and in responses to class polls.

Anaput Object 30

This value specifies the default variation for object 30, anaput. The default variation is used whenever variation 0 is requested, and in responses to class polls.

Anaput Object 32

This value specifies the default variation for object 32, anaput change events. The default variation is used whenever variation 0 is requested, and in responses to class polls.

1 (32-bit binary counters without time) 2 (16-bit binary counters without time) 5 (32-bit binary counters with time) 6 (16-bit binary counters with time) 255 (disabled) 1 (32 bit analog with status), 1 2 (16 bit analog with status), 3 (32 bit analog without status), 4 (16 bit analog without status) 1 (32 bit analog without 3 time) 2 (16 bit analog without time) 3 (32 bit analog with time) 4 (16 bit analog with time)

Anaput Object 34

In addition, the reporting mode of the ‘without time’ variations may be specified. This value specifies the default variation for object 34, anaput reporting deadband. The default variation is used whenever reads of variation 0 is requested.

1 (16 bit analog) 2 (32 bit analog)

1

CM S Yes

HMI (Control) No

Yes

No

Yes

No

Yes

No

Deadband values can be changed within the RC10 over SCADA by DNP3 function code 22. Default deadbands are set for all analog points and can be mapped into any particular configuration using CMS software




NOJA-522-06

Page 105 09-01-2014

NOJA-522-06 8.2

DIAL OUT SETTINGS

Setting

Description

Range

Dial Out

Enable RC10 dial out

Predial string Dial Numbers

Set of modem commands sent to modem before dialing a number. A maximum of five telephone numbers for dialing out and connecting to a master. Each number can be a maximum of 18 characters; a comma (,) is used to generate a pause of 1 sec. If the first number fails to respond, the RC10 waits for the Autodial Interval to expire and tries the next available number in the list. Interval between failure to connect to one number before initiating a call to the next. Setting to zero (0) disables the interval and the next number is dialed immediately the preceding number fails. The length of time the RC10 will wait after dialing a number for a connection to be established.

Autodial Interval

Connection Timeout

On (Ticked) Off (Un-ticked) Predefined AT commands. 5 strings, each 18 characters long without AT prefix. See dialing chars* 0 to 255s Step size 1s

Default for Modem On

Accessib le from CMS Yes

Accessib le from HMI No

ATD

Yes

No

-

Yes

No

3

Yes

No

60s

Yes

No

0 to 255s Step size 1s

* The following characters can be used in the pre-dial string and dial numbers: Character 0-9 # * P

Description Dialing digits.

T

Tone dialing

, (comma)

Pause. Used to set a pause between digits.

; (semicolon)

Return to command state after dialing.

!

Hook flash.

@

Wait for 5 seconds before proceeding.

R

Reverse handshake (go on-line in auto-answer mode).

W

Waits for second dial tone.

Pulse dialing.

For full details on configuring the communications refer to the document RC10 SCADA Interface Description (NOJA-565-00)




NOJA-522-06

Page 106 09-01-2014

Noja-522-06 Rc10 Dnp3 Device Profile 61693p

Overview 26281t

More details 6y5l6z

Related Documents 3h463d

Noja-522-06 Rc10 Dnp3 Device Profile 61693p

Dnp3 Tutorial 2v6e1j

Protocolo Dnp3 705l26

Rc10 Worlds Manual.pdf 2y2n2g

El Protocolo Dnp3 y5z2m

Protocolo De Comunicaciones Dnp3 2a362i

More Documents from "acosta" 5r2w1r

Noja-522-06 Rc10 Dnp3 Device Profile 61693p

Guia Basica Multisim 1j85j

4p345f

Tachosoft Kilometraje Calculator Manual 2z3729

4p345f

4p345f