Parker - Oring Handbook q6c6l

O-Ring Guide

Content 4

Parker´s safety programme

6 Introduction 11 O-ring material offering 14 Parker O-ring compound numbering system 15 Compound tables 15 Polyacrylate (ACM) 15 Polychloroprene rubber (CR) 15 Ethylene propylene rubber (EPDM) 16 Nitrile butadiene rubber (NBR) 17 Hydrogenated nitrile butadiene rubber (HNBR) 17 Thermoplastic elastomers (Ultrathan®) 18 Silicone rubber (VMQ) 18 Liquid silicone rubber (LSR) 19 Fluorosilicone (FVMQ) 19 Fluorocarbon (FKM) 20 High performance fluoroelastomers (HiFluor®) 21 Perfluoro elastomer (Parofluor®) 22 Perfluoro elastomer (Parofluor Quantum®) 23 Range of application 26 Aerospace materials 28 Specifications 31

Deformation force

39 Forms of installation 40 Static seal – axial 42 Static seal – radial 44 Static seal – dovetail groove 46 Dynamic seal – hydraulic 49 Sizing charts 50 2-xxx sizes 55 3-xxx sizes 56 5-xxx sizes 57 6-xxx sizes 71 O-ring sizes acc. to inner diameter 85 Parbak® Back-up rings

3

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker´s safety programme Warning – responsibility This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by s having technical expertise. The , through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalogue and in any materials provided by Parker or its subsidiaries or authorized distributors. To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the , the is responsible for determining that such data and specifications are suitable and sufficient for all applications and responsibly foreseeable uses of the components or systems. Range of application Our seals may only be used within the application parameters stated in our documents as regards compatibility with media, pressures, temperatures and time of storage. Application or use outside of the specified application parameters as well as the selection of different compounds by mistake may result in damage to life, the environment and/or equipment and facilities. The information contained in our publications is based on know-how developed over decades of experience in the manufacturing and application of seals. Despite this experience, unknown factors arising out of the practical application of seals may considerably affect the overall applicability of this information in such a way that the recommendations provided herein are not to be considered generally binding. The data for operating pressure, operating temperature, and surface speed stated in the columns represent maximum values and are interrelated. Under extreme working conditions it is recommended not to use all maximum values simultaneously. For special requirements (pressure, temperature, speed, etc.) please our consultancy service, so that suitable materials and/or designs can be recommended. Compatibility of seals and operating media / cleaning agents Due to the great diversity of operational parameters affecting fluidic devices and their impact on seals, it is absolutely imperative that manufacturers of these devices approve seals for functional and operational suitability under field conditions. Furthermore, in view of the consistent increase of newly available media used as hydraulic oils, lubricants, and cleaning agents, special attention is invited to the aspect of compatibility with sealing elastomers currently in use. Additives contained in base media in order to enhance certain functional characteristics may affect compatibility characteristics of sealing materials. For this reason, it is imperative that any product equipped with our seals be

4

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker´s safety programme tested for compatibility with operational media or cleaning agents approved or specified by you either at your plant or by means of field tests prior to any field use. We kindly ask you to comply with this notice since, as a manufacturer of seals, we are not in a position, as a matter of principle, to perform simulations of any and all conditions present in the final application nor of knowing the composition of the operational media and cleaning agents used. Design modifications We reserve the right to make design modifications without prior notification. Prototypes and samples Prototypes and samples are produced from experimental moulds. The subsequent series production may differ in of production techniques from the prototype production unless specific agreement to the contrary was reached beforehand. Delivery and services The delivery guarantee (availability of moulds) for individual dimensions of our range of products is limited to a period of 7 years. Damaged moulds, including standard items, can only be replaced in case of sufficient demand. Most of the dimensions stated in this catalogue are normally (but not as a matter of course) available ex stock. For the production of smaller quantities, special compounds, and in case of special production procedures, we reserve the right of charging a prorated share of set-up costs. All deliveries and services are subject to our . Quality systems Our manufacturing sites are certified according to ISO 9001 and/or ISO/ TS 16949. Copyright All rights reserved by Parker Hannifin Corporation. Extracts may only be taken with permission. Modification rights reserved. Validity This edition supersedes all prior documents.

5

O-Ring Guide Parker Hannifin O-Ring Division Europe

Introduction

Sealing technology by Parker-Prädifa The Engineered Materials Group of the Parker Hannifin Corporation is a worldwide leader in the development, production and sale of sealing systems, vibration dampers, EMI shielding systems and thermally conductive materials.

Quality assurance In the O-ring division’s world-class facilities, skilled Parker technicians manufacture O-rings to exacting standards. From in-house mixing and tooling operations to the final non- inspection process, state-of-the art technology is employed to provide unparalleled material consistency and dimensional control. Quality registrations are maintained to ensure superior product performance and process repeatability.

Research and development Based on decades of experience in a wide range of markets Parker develops tailored sealing solutions for virtually any application. Parker’s sealing experts can draw on an extensive network of R+D laboratories around the globe. State-of-the-art materials, high-end manufacturing technology and designs that are perfectly tailored to the specific application result in products and solutions that have one aim in mind: the full satisfaction of our customers and partners.

Computer simulation Parker-Prädifa uses the Finite Elements Method to develop and optimise sealing systems. Particularly elastomer materials with their non-linear properties cannot be described strictly by using standard software. Therefore, Parker-Prädifa has developed proprietary mathematical models to describe the complex material properties and special measuring methods to capture the relevant material parameters. Computer simulation allows experts to detect weak areas as early as in the concept phase and to optimise materials or geometries. This saves development time and costs.

6

O-Ring Guide Parker Hannifin O-Ring Division Europe

Introduction

Introduction

Literature The Parker O-Ring Handbook has been a standard reference work used by seal designers for decades. It contains comprehensive information about the properties of the most important sealing elastomers, typical O-ring application examples, examples of statically acting seal designs plus descriptions of conditions that may lead to O-Ring failure. In addition, the handbook contains an overview of international dimensions and standards as well as media compatibility data for fluids, gases and solids.

O-Ring Handbuch O-Ring Handbook

Materials Tailored materials require tailored compounding processes. Therefore, Parker produces its rubber mixtures and polymerises its thermoplastic materials in-house. The portfolio of materials developed and produced by Parker ranges from compounds for extremely low temperatures down to –60 °C (silicones) to very high temperatures up to +320 °C (Parofluor®). Parker offers the appropriate compound for the specific application requirements including excellent resistance against aggressive chemicals. With excellent extrusion and abrasion resistance Parker’s proprietary polyurethane line is suitable for an extremely extensive application range and continually new uses.

Product lines Parker manufactures O-rings and special moulded parts for automotive engineering, the chemical and bio-chemical industries, fluid power, refrigeration and air conditioning technology, the petroleum sector, aerospace, the semiconductor industry and many other industrial sectors.

7

O-Ring Guide Parker Hannifin O-Ring Division Europe

Introduction

O-rings O-rings are manufactured according to metric and imperial international standards such as AS-568B, DIN ISO 3601 and JIS. Custom sizes of almost any dimension are possible such as miniature O-rings and special O-rings with large dimensions.

O-ring kits The handy carrying case with O-rings is ideally suited for repairs, assembly jobs and workshops, and finally puts an end to the search for the right O-ring. Parker offers it in various versions: with O-rings in selected imperial and metric standard dimensions and appropriate materials or with customised content. Compact, well arranged and always within reach, the kit provides the appropriate materials for quick use.

Accessories Products to assist O-ring s include assembly greases and lubricants, sizing cones and extraction tools.

Parbak® Back-up rings

Parbak® Back-up rings prevent extrusion in high-pressure applications, help to maintain the lubricant film and thus prolong the service life of O-rings. The Parbak® numbers correspond to the size designations of the 2-xxx series of the Parker O-rings they are installed with (e.g. 8-211, N 300-90 fits O-ring 2-211, N 674-70).

8

O-Ring Guide Parker Hannifin O-Ring Division Europe

ParCoat® Coating O-rings with ParCoat® coatings can be assembled with low exertion of force using automatic equipment. The rings will not stick together during the feeder process. Prior to installation they can be elongated by over 150 % without causing the anti-friction coating to burst or crack. Benefits • Clearly reduced frictional forces • No damage to seals during installation or assembly • Faster, more cost-efficient assembly process • Improves interfacial seal tightness, especially for sealing against gases • Seals will not stick together in automatic feeding processes • No soiling or contamination • Translucent ParCoat® treated O-rings insures no risk of mix-ups as basic elastomer compound colour remains visible • Elongation capacity above 150 %, depending on type • Suitable for nearly all standard elastomer types (for LSR not all coatings applicable) • In different colours available

9

O-Ring Guide Parker Hannifin O-Ring Division Europe

Introduction

Introduction

10

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

O-ring material offering

Parker O-ring compounds are formulated to meet the most stringent industry standards, including FDA, USP, KTW, DVGW, BAM, WRAS (WRC), NSF, Underwriters Laboratories (UL), Aerospace (AMS) and many customer-specific requirements.

11

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

Compounds O-rings can be molded in a wide range of compounds in hardnesses from 40 to 90 Shore A. These materials include:

• Polyacrylate (ACM) ACM (acrylic rubber) has good resistance to mineral oil, oxygen and ozone. The water compatibility and cold flexibility of ACM are considerably worse than those with NBR.

• Polychloroprene rubber (CR) Also known by the tradename Neoprene, polychloroprene was the first synthetic rubber and exhibits generally good ozone, aging, and chemical resistance. It has good mechanical properties over a wide temperature range.

• Nitrile butadiene rubber (NBR) Nitrile rubber (NBR) is the general term for acrylonitrile-butadiene terpolymer. The acrylonitrile content of nitrile sealing compounds varies considerably (18 to 50 %). Polymers with higher ACN content exhibit less swell in gasoline and aromatic solvents, while lower ACN polymers exhibit better compression set and low temperature flexibility. Polymer is also called Buna-N.

• Hydrogenated nitrile butadiene rubber (HNBR) Hydrogenated NBR was developed as an air-resistant variant of nitrile rubber. In HNBR, the carbon-carbon double bonds in the main polymer chain are saturated with hydrogen atoms in a process called “hydrogenation” that improves the material’s thermal stability and oxidation resistance.

• Ethylene propylene rubber (EPDM) EPDM is a terpolymer of ethylene, propylene, and a diene third monomer used for cross-linking.

• Silicone rubber (VMQ) Silicone elastomers have relatively low tensile strength, poor tear and wear resistance. Silicones also possess good insulating properties and tend to be physiologically neutral.

• Fluorosilicone (FVMQ) Fluorosilicone is a silicone polymer chain with fluorinated side-chains for improved oil and fuel resistance. The mechanical and physical properties are very similar to those ofsilicone.

• Liquid silicone rubber (LSR) Liquid Silicone Rubber (LSR) offer great advantage producing efficient high quantity silicone parts. Flash less production gives opportunities for difficult molded shapes. I.E. for fastidious medical or automotive applications.

12

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

• Fluorocarbon (FKM) Fluorocarbon (FKM) has excellent resistance to high temperatures and a broad range of chemicals. Permeability and compression set are excellent.

As a high-performance fluoroelastomer, HiFluor® offers chemical stability comparable to perfluoro elastomers (FFKM) in nearly all media. Particularly in polar solvents, HiFluor® exhibits major advantages over conventional FKM polymers. HiFluor® offers a wide range of application solutions in all industrial sectors. From conventional O-rings in standard (imperial and metric) dimensions through to diaphragms and moulded engineering parts according to customers’ drawings, the compound can be processed in rubber-metal composites as well.

• Parofluor® (FFKM) The Parofluor® range consists of advanced perfluorinated elastomers (FFKMs) exclusively developed and produced by Parker Hannifin. They are carried under the trade names of Parofluor® and Parofluor Quantum®. Compared with other perfluorinated elastomers Parofluor® compounds offer outstanding retained resiliency as they have been developed specifically for extremely challenging sealing applications.

13

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

• HiFluor® (FKM)

O-ring material offering

Parker O-ring compound numbering system Parker O-ring compounds are described by the following system.

N 0674 -70

Hardness (Shore A) Sequence number (compound code) Polymer-code A Polyacrylate C Neoprene (Chloroprene) E Ethylene propylene L Fluorosilicone N Nitrile (Buna N) and HNBR S Silicone V Fluorocarbon, HiFluor®, Parofluor® P Thermoplastic elastomers

14

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

Compound tables Colour

[Shore A]

Tempera­ Properties / Applications ture range static [°C]

Polyacrylate rubber (ACM) 70

A8845-70

±5

black

-20 +150

Polychloroprene rubber (CR) C0557-70

70

±5

black

-40 +100 • often used in refrigerant (e.g. R134a or R22) • good aging and salt water resistance

C0944-70

70

±5

red

-40 +100

Ethylene propylene rubber (EPDM) E0529-60

60±5

black

-50 +150

E0540-80 80±5

black

-50 +150 • standard compound • good compression set • hot water • air to 150 °C • steam to 200 °C • dilute acids • fire-resistant hydraulic fluids with ­phosphate ester base • brake fluids with non-mineral oil base

E3609-70

70±5

black

-50 +150 • standard compound • FDA-compliant • (EC) No. 1935/2004 • USP Class VI • not suitable for use with milk and nutritional oil

E3678-80

80±5

violet

-50 +150

E3804-90

90±5

black

-50 +150 • Parbak® compound

1)

1)

bold printed compounds are 2-xxx standard and available ex-stock.

The temperature ranges given are only valid where elastomer medium compatibility is absolute. Recommendations in the column remarks / applications on application design and material selection are based on available technical data and are offered as suggestions only. Each should make his own tests to determine the suitability for his own particular use. Parker offers no express or implied warranties concerning the form, fit, or function of a product in any application.

15

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring Dichtungswerkstoffe material offering

Compound Hard­ code ness

O-ring material offering Compound Hard­ code ness

Colour

[Shore A]

Tempera­ Properties / Applications ture range static [°C]

Ethylene propylene rubber (EPDM) E8556-70

70±5

black

-50 +150 • for industrial cooling water applications • improved ageing resistance

E8743-70

70±5

black

-50 +150 • FDA-compliant • (EC) No. 1935/2004 • for food industry • ADI-free

E8780-80

80±5

black

-50 +150 • standard for drinking water applications • approvals: W 270, EN 681-1, W 534, KTW • FDA-compliant (not suitable for use with milk and nutritional oil) • (EC) No. 1935/2004

E8790-70

70±5

black

-50 +150 • standard for drinking water applications • approvals: KTW, WRAS, W 270, EN 681-1, W 534, KIWA • FDA-compliant (not suitable for use with milk and nutritional oil) • (EC) No. 1935/2004

Nitrile butadiene rubber (NBR) N0525-60

60±5

black

-35 100

N0552-901) 90±5

black

-30 100

N0674-70 70±5

black

-35 100

• standard compound • resistance to mineral oil and mineral oil products, animal and vegetable oils • generally suited for hydraulic and pneumatic systems compatible with hydraulic oil, water glycol (HFC fluids) and oil in water emulsions (HFA fluids)

N3505-50

50±5

black

-35 100

• improved ozone and weather-proof resistance

N3575-75

75±5

black

-50 100

• low temperature with improved oil resistance

N3578-80

80±5

black

-40 100

1)

1)

bold printed compounds are 2-xxx standard and available ex-stock.

The temperature ranges given are only valid where elastomer medium compatibility is absolute. Recommendations in the column remarks / applications on application design and material selection are based on available technical data and are offered as suggestions only. Each should make his own tests to determine the suitability for his own particular use. Parker offers no express or implied warranties concerning the form, fit, or function of a product in any application.

16

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering Compound Hard­ code ness

Colour

[Shore A]

Tempera­ Properties / Applications ture range static [°C]

Hydrogenated nitrile butadiene rubber (HNBR) 85±5

black

-35 +150

N3512-90

90±5

black

-35 +150

N3554-75

75±5

light green

-35 +150

N3573-75

75±5

black

-35 +150

N3723-80

80±5

black

-35 +150

N3813-70

70±5

black

-40 +150 • for low temperatures

N3831-70

70±5

black

-35 +150 • suitable for AdBlue® 2) to ca. 80 °C

N3837-85

85±5

green

-35 +150

N8505-70

70±5

green

-35 +150 • suitable for biodiesel (RME) applications up to 80 °C

N8680-90

90±5

black

-40 +150 • for low temperatures

N8888-70

70±5

yellow

-35 +150 • for gas- and water application • approval for EN 549, EN 681-1

O-ring material offering

N3510-85

Thermoplastic elastomers (Ultrathan®) P4300

92±5

yellow

-30 +110 • excellent high-temperature behaviour • excellent dynamic behaviour

P5000

94±5

dark green

-20 +100 • very good hydrolysis resistance • FDA-compliant

P5001

94±5

brown

-35 +100 • good hydrolysis resistance

P5007

82±5

green, transp.

-35

P5008

94±5

green

-35 +100 • standard compound

P5009

94±5

grey

-45

P5012

90±5

red

-38 +100 • good hydrolysis resistance

+80 • standard compound

+95 • for low temperatures

1)

bold printed compounds are 2-xxx standard and available ex-stock.

2)

ed trademark of VDA

The temperature ranges given are only valid where elastomer medium compatibility is absolute. Recommendations in the column remarks / applications on application design and material selection are based on available technical data and are offered as suggestions only. Each should make his own tests to determine the suitability for his own particular use. Parker offers no express or implied warranties concerning the form, fit, or function of a product in any application.

17

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering Compound Hard­ code ness

Colour

[Shore A]

Tempera­ Properties / Applications ture range static [°C]

Thermoplastic elastomers (Ultrathan®) P5029

94±5

nature

-20 +100 • very good hydrolysis resistance • FDA-compliant

P5070

83±5

green

-35

+85 • good hydrolysis resistance

P5075

80±5

ochre

-45

+80 • for low temperatures

P6000

95±5

charcoal- -35 +110 • very high mechanical strength grey • extrusion resistance

P6030

93±5

orange

-35 +105 • high mechanical strength • extrusion resistance

Silicone rubber (VMQ) S0595-50

50±5

red

-55 +200

S0604-70

70±5

red

-55 +200 • standard compound • hot air to 210 °C • water to 100 °C • only suitable as static seal

S0613-60

60±5

red

-55 +200

S0614-80

80±5

red

-55 +200

Liquid silicone rubber (LSR) S3693-50

50±5

reddish brown

-50 +200

S3695-60

60±5

reddish brown

-50 +200

S3697-40

40±5

reddish brown

-50 +200

S3698-70

70±5

reddish brown

-50 +200

1)

bold printed compounds are 2-xxx standard and available ex-stock.

The temperature ranges given are only valid where elastomer medium compatibility is absolute. Recommendations in the column remarks / applications on application design and material selection are based on available technical data and are offered as suggestions only. Each should make his own tests to determine the suitability for his own particular use. Parker offers no express or implied warranties concerning the form, fit, or function of a product in any application.

18

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering Compound Hard­ code ness

Colour

[Shore A]

Tempera­ Properties / Applications ture range static [°C]

L0677-70

70±5

blue

-60 +170 • for high temperatures • good low-temperature resistance • mostly fitted where fuel and oil resistance is important • predominant in aircraft

L0806-80

80±5

blue

-60 +170 • approvals for military and aerospace applications

L3355-70

70±5

yellow

-60 +170 • used in automotive fuel couplings

L8559-70

70±5

blue

-60 +170

L8585-80

80±5

blue

-60 +170 • approvals for aerospace applications

Fluorocarbon (FKM) V0709-90

90±5

black

-25 +200

V0747-75 75±5

black

-25 +200 • standard compound • for high temperatures • hot oil • aromatic solvents • wide chemical resistance • fire-resistant fluids with phosphate ester and chlorinated hydrocarbon base • copolymer

V0763-60

60±5

brown

-25 +200 • copolymer

V0884-75

75±5

brown

-25 +200 • copolymer

V0894-90

90±5

brown

-25 +200 • copolymer

V3642-75

75±5

black

-25 +200 • terpolymer

V3670-70

70±5

green

-25 +200 • copolymer

V3681-80

80±5

green

-25 +200 • copolymer

V3736-75

75±5

black

-28 +200 • terpolymer • improved low temperature resistance

1)

1)

bold printed compounds are 2-xxx standard and available ex-stock.

The temperature ranges given are only valid where elastomer medium compatibility is absolute. Recommendations in the column remarks / applications on application design and material selection are based on available technical data and are offered as suggestions only. Each should make his own tests to determine the suitability for his own particular use. Parker offers no express or implied warranties concerning the form, fit, or function of a product in any application.

19

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

Fluorosilicone (FVMQ)

O-ring material offering Compound Hard­ code ness

Colour

[Shore A]

Tempera­ Properties / Applications ture range static [°C]

Fluorocarbon (FKM) V3738-75

75±5

black

-20 +200 • improved medium compatibility

V8592-75

75±5

blue

-40 +200 • for low temperatures

V8703-75

75±5

black

-30 +200 • improved low temperature resistance • suitable for biodiesel (RME) applications

V8722-75

75±5

black

-25 +200 • FDA-compliant • (EC) No. 1935/2004 • ADI-free • improved resistance against water glycol and acids

V8750-70

70±5

black

-25 +200 • FDA-compliant • (EC) No. 1935/2004 • food industry

V8802-80

80±5

blue

-40 +200 • for low temperatures

V8877-75

75±5

blue

-50 +200 • highly improved low temperature resistance

V8989-80

83±5

black

-40 +200 • for low temperatures • improved medium compatibility and mechanical properties

High performance fluoroelastomer (HiFluor®) V3819-75

75±5

black

-25 +250 • improved resistance against water glycol and acids • excellent availability in Parker standard dimensions

V8534-90

90±5

black

-25 +250 • improved resistance to explosive decompression and gap extrusion • off-shore and petrochemical applications

V8730-70

70±5

white

-25 +250 • food industry • FDA-compliant • (EC) No. 1935/2004 • particularly suitable for use with high processing temperatures and aggressive media

1)

bold printed compounds are 2-xxx standard and available ex-stock.

The temperature ranges given are only valid where elastomer medium compatibility is absolute. Recommendations in the column remarks / applications on application design and material selection are based on available technical data and are offered as suggestions only. Each should make his own tests to determine the suitability for his own particular use. Parker offers no express or implied warranties concerning the form, fit, or function of a product in any application.

20

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering Compound Hard­ code ness

Colour

[Shore A]

Tempera­ Properties / Applications ture range static [°C]

V3852-65

65±5

black

-25 +250 • preferably used for moulded functional components and membranes / diaphragms

V8558-75

75±5

green

-25 +260 • coloured version

V8879-75

75±5

black

-15 +230 • very good chemical resistance • very good varnish stability

Perfluoro elastomer (Parofluor®) V3734-70

70±5

black

-25 +240 • for low temperatures • for aerospace

V8545-75

75±5

black

-15 +300 • best compound for hot water and steam applications • AMS 7257

V8562-75

75±5

white

-15 +300 • for high temperature-plasma-applications • dry applications in semiconductor industries

V8588-90

90±5

black

-15 +260 • ED resistant • Norsok M-710

V8920-75

75±5

black

-15 +260 • good resistance in hot water • for wet processes in semiconductor applications

V8921-75

75±5

white

-15 +260 • pure compound for sterile and pharmaceutical technology • for oxidising media

V8930-75

75±5

black

-15 +325 • for high temperatures • not recommendedfor hot aliphatic amine and water steam

V8931-75

75±5

black

-15 +310 • for high temperatures • for hot aliphatic amine and water steam

V8950-75

75±5

black

-15 +240 • FDA-compliant • (EC) No. 1935/2004 • ADI-free • for food industry, pharmacy and biotechnology

1)

bold printed compounds are 2-xxx standard and available ex-stock.

The temperature ranges given are only valid where elastomer medium compatibility is absolute. Recommendations in the column remarks / applications on application design and material selection are based on available technical data and are offered as suggestions only. Each should make his own tests to determine the suitability for his own particular use. Parker offers no express or implied warranties concerning the form, fit, or function of a product in any application.

21

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

High performance fluoroelastomer (HiFluor®)

O-ring material offering Compound Hard­ code ness

Colour

[Shore A]

Tempera­ Properties / Applications ture range static [°C]

Perfluoro elastomer (Parofluor®) V8951-70

70±5

white

-15 +240 • FDA-compliant • (EC) No. 1935/2004 • ADI-free • USP Class VI • for pharmacy, biotechnology and medical technology

FF400-80

80±5

black

-40 +275 • for low temperatures • oil and gas • chemical industries • ED resistant

Perfluoro elastomer (Parofluor Quantum®) V8787-75

75±5

black

-20 +230 • optimized paint, varnish and solvent stability

V8844-75

75±5

nature

-20 +230 • optimized paint, varnish and solvent stability

V8910-75

80+8 -5

black

-20 +220 • improved chemical resistance • ADI-free

V8911-75

75+8 -5

white

-20 +220 • improved chemical resistance

1)

bold printed compounds are 2-xxx standard and available ex-stock.

The temperature ranges given are only valid where elastomer medium compatibility is absolute. Recommendations in the column remarks / applications on application design and material selection are based on available technical data and are offered as suggestions only. Each should make his own tests to determine the suitability for his own particular use. Parker offers no express or implied warranties concerning the form, fit, or function of a product in any application.

22

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

Range of application

LP-gas



F

G

H

I

J

 

  

 



 

Compounds for gas supply and appliances The following Parker Hannifin compounds are approved by the German Association for Gas and Water (DVGW) for the applications listed: Parker compound Polymer

Colour

V0747-75

FKM

black

Standard DIN EN 549

N0552-90

NBR

black

DIN EN 549

N0674-70

NBR

black

DIN EN 549, VP 406

N3506-70

NBR

black

DIN EN 549 DIN EN 549

N3578-80

NBR

black

N3829-70

NBR

black

DIN EN 549

N8902-85

NBR

black

-

N8888-70

HNBR

yellow

DIN EN 549, VP 406, VP 614

S3698-70

VMQ

red

DIN EN 549

V0884-75

FKM

brown

DIN EN 549

Compounds for the food and pharmaceutical industry Seals coming into with products in food, beverage and pharmaceutical production must be resistant to “CIP” (Cleaning in Place) and “SIP” (Sterilisation in Place) processes. The silicone materials are suitable for use in food applications with respect to their physiological properties because they are inert as well as odourless and tasteless. In addition to chemical and thermal resistance, the sealing compounds have to meet various national, European and international regulations. In , The Federal Institute for Risk Assessment (BfR) issues recommendations for ingredients, additives, residues, contaminations and

23

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

 

Anhydrous ammonia

E

Heated fuel oil

D

  

Diesel fuel, fuel oil, lubricating oil

C



MFG or natural gas

Gasoline/alcohol blends

B

MPS gas

V0884-75

A

Naptha or kerosene

V0747-75

Gasoline

Compound code N0674-70

Fire extinguishing agents

Underwriters laboratories approved services

O-ring material offering permissible migration levels (migration or leaching) in foodstuffs and animal feed. 3-A Sanitary Standards Inc. (3-A SSI) is an independent organisation dedicated to advancing hygienic equipment design for the U.S. food, beverage and pharmaceutical industries. Important regulations: • Annex I, Article 3 of European Regulation (EC) No. 1935/2004 • Regulation (EC) No. 1907/2006 on the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) • The USP (United States Pharmacopiea) Class VI protocol certifies the biological compatibility with living organisms and thus the harmlessness of sealing materials to health. The most important test protocols are USP Class VI, Part 88 and USP Class VI, part 87 acc. to ISO 10993-1. Parker has developed formulations which are ADI-free (free from Animal Derived Ingredients) because such ingredients may cause BSE (bovine spongiform encephalopathy).

1)

Parker compound

Polymer Colour

Standard

E3609-70

EPDM

black

FDA1), (EC) No. 1935/2004, USP Class VI

E8743-70

EPDM

black

FDA, (EC) No. 1935/2004, BfR, ADI-free

E8780-80

EPDM

black

FDA1), (EC) No. 1935/2004, BfR

E8790-70

EPDM

black

FDA1), (EC) No. 1935/2004, BfR

P5000

TPU

green

FDA

P5029

TPU

nature

FDA

S3693-50

LSR

reddish brown

FDA, (EC) No. 1935/2004, BfR

S3695-60

LSR

reddish brown

FDA, (EC) No. 1935/2004, BfR

S3697-40

LSR

reddish brown

FDA, (EC) No. 1935/2004, BfR

S3698-70

LSR

reddish brown

FDA, (EC) No. 1935/2004, BfR

V0747-75

FKM

black

ADI-free

V8722-75

FKM

black

FDA, (EC) No. 1935/2004

V8750-70

FKM

black

FDA, (EC) No. 1935/2004

HiFluor® V8522-75

FKM

white

ADI-free

HiFluor® V8730-70

FKM

white

FDA, (EC) No. 1935/2004

Parofluor® V8742-70 FFKM

white

ADI-free

Parofluor® V8950-75 FFKM

black

FDA, (EC) No. 1935/2004, ADI-free

Parofluor® V8951-70 FFKM

white

FDA, (EC) No. 1935/2004, ADI-free, USP Class VI

Not suitable for use with milk and nutritional oil

24

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

KTW approved compounds

KTW: KTW is the nationally recognized standard for all devices, components and materials which drinking water. In addition to (KTW), Great Britain (WRAS), the USA (NSF61), (ACS) and the Netherlands (KIWA) have published their own regulations for these applications. Parker’s O-Ring Division has developed several materials that are certified to KTW. Parker Compound

Polymer

E1549-70

EPDM

Watertemperature 85°C

Colour

Standard

black

WRAS

black

W270, KTW

black

KTW, W270

82°C E8780-80

EPDM

90°C

E8790-70

EPDM

90°C

NSF 61

-

EN 681-1, W 534

85°C

WRAS

90°C

KIWA

N8888-70

HNBR

-

EN 681-1, W 534 yellow

25

EN 681-1, EN 549

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

Sealing compounds for use in drinking water and heating applications are subject to a large number of approval regulations designed to ensure their harmlessness from the stage of water extraction, treatment and transport through to the consumer’s tap. Worldwide, almost all countries have issued their own drinking water regulations including specific tests and lists of approved ingredients. The regulations are complemented by physical and microbiological examinations.

O-ring material offering

Aerospace materials The aerospace industry demands the most from elastomeric compounds. Special materials often must be developed to meet specification requirements. Additionally many special requirements must be met during the production of finished parts, not least to meet safety, technical and quality requirements. AMS1) and NAS2) rubber specification descriptions Specifications

1) 2)

Parker compound

Hardness Description title (Shore A)

AMS3201

N0545-40

35 - 45

dry heat resistance

AMS3205

N0299-50

45 - 55

low temperature resistance

AMS3208

C0267-50

45 - 55

weather resistant, chloroprene type

AMS3209

C1124-70

65 - 75

weather resistant, chloroprene type

AMS3212

N0525-60

55 - 65

aromatic fuel resistant general purpose, fluid resistant

AMS3220

N0525-60

55 - 65

AMS3238

B0318-70

65 - 75

phosphate-ester resistant, butyl type

AMS3301

S0469-40

35 - 45

silicone, general purpose

AMS3302

S0595-50

45 - 55

silicone, general purpose

AMS3303

S0613-60

55 - 65

silicone, general purpose

AMS3304

S1224-70 S0604-70

65 - 75

silicone, general purpose

AMS3305

S0614-80

75 - 85

silicone, general purpose

AMS3325

L1223-60 LM152-60

55 - 65

fluorosilicone rubber, fuel and oil resistant

AMS3337

S0383-70

65 - 75

silicone, extreme low temperature resistant

AMS3345

S0899-50

45 - 55

silicone rubber

AMS3357

S1224-70 S0604-70

65 - 75

silicone rubber, lubricating oil, compression set resistant

AMS7257

V8545-75 FF200-75

70 - 80

sealing rings, perfluorocarbon, ­high ­temperature resistant

AMS7259

V0709-90

85 - 95

high temp. and fluid resistant, very low compression set, FKM

AMS7267

S0355-75

70 - 80

silicone, heat resistant, low compression set

AMS7271

N0506-65

60 - 70

fuel and low temperature resistant

Aerospace Material Specification issued by the Society of Automotive Engineers, Inc. National Aerospace Standard issued by Aerospace Industries Association of America, Inc.

26

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

1) 2)

Parker compound

Hardness Description title (Shore A)

AMS7272

N0287-70

65 - 75

synthetic lubricant resistant

AMS7276

V1164-75 V1226-75 V0747-75

70 - 80

high temperature fluid resistant, very low compression set, FKM

NAS1613

E1267-80

75 - 85

packing, O-ring, phosphate ester resistant

AMS-P-5315

N0602-70

65 - 75

packing, O-ring, hydrocarbon fuel resistant

AMS-P-5510

N0507-90

85 - 95

gasket, straight thread tube fitting boss

AMS-R-6855

N0406-60 C1124-70

55 - 75

synthetic rubber sheets, strips, moulded or extruded shapes, synthetic oil resistant

AMS-P-25732

N0304-75

70 - 80

packing, preformed, petroleum hydraulic fluid resistant, limited performance

AMS-R-25988

L1223-60 L1120-70 L1218-80 L1077-75 LM152-60 LM153-70 LM154-75 LM155-80

55 - 85

rubber, fluorosilicone elastomer, oil and fuel resistant

AMS-R-83248

V1164-75 V1226-75 V0747-75 V0709-90

70 - 95

rubber, fluorocarbon elastomer, high temperature fluid and compression set resistant

AMS-P-83461

N0756-75

70 - 80

packing, preformed, petroleum hydraulic fluid resistant, improved performance

AMS-R-83485

V0835-75

70 - 80

rubber, fluorocarbon elastomer, improved performance at low temperatures

Aerospace Material Specification issued by the Society of Automotive Engineers, Inc. National Aerospace Standard issued by Aerospace Industries Association of America, Inc.

27

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

Specifications

O-ring material offering

Specifications Airbus Nord-Sud Aviation (NSA) Specification

Parker compound

Description

NSA 5512 NSA 8200 NSA 8201 NSA 8202 NSA 8203 NSA 8204 NSA 8205 NSA 8206 NSA 8207 NSA 8213 NSA 8216 NSA 8218 NSA 8671

Special L8585-80 E1267-80 C3645-80 L8585-80 E1267-80 C3645-80 S0604-70 S0604-70 E1267-80 E1267-80 E1267-80 W5036

bonded seal sizes 3-xxx sizes 3-xxx sizes 3-xxx sizes 2-xxx sizes 2-xxx; NAS 1613; colour code sizes 2-xxx sizes 2-xxx sizes 3-xxx square ring square ring square ring square ring; PTFE

Norme Française (NF), (french standard) Specification

Parker compound

Category

NF L17-241 NF L17-160 NF L17-164 NF L17-261 NF L17-261 NF L17-250-4

E1267-80 V0709-90 V0747-75 L8585-80 L1218-80 S0604-70

41B8 60C9 64C8 61D8 61D8 EN 2261

28

O-Ring Guide Parker Hannifin O-Ring Division Europe

O-ring material offering

Specification

Parker compound

5.5440 5.5502 5.5600 5.5601 5.5602 5.5603 5.5612 5.5627 5.5629 5.5655 5.5688 5.5701 5.5702 5.5703 5.5704 5.5707 5.5709 5.5710 5.5801 5.5802 5.5804 5.5808 5.5810 5.5813 5.5814 5.5829 5.5855

C0365-45 S0595-50 E0529-65 N0406-60 N0239-60 S0613-60 N0406-60 N0261-65 N0525-60 N0406-60 L3747-60 V0747-75 N0674-70 S0604-70 V3670-70 B3688-70 C0557-70 L0677-70/L8559-70 N3578-80 E0540-80 V0747-75 V0709-90 N0552-90 L0806-80 S0614-80 N0755-80 N3518-80

O-ring material offering

Compound-Datasheet (WL)

29

O-Ring Guide Parker Hannifin O-Ring Division Europe

30

O-Ring Guide Parker Hannifin O-Ring Division Europe

Deformation force The following charts are included to facilitate engineering analysis. Additional information is available in the Parker O-Ring Handbook.

Deformation force

Deformation force

The force necessary to deform an O-ring cross-section by a given amount (in per cent) depends on the compound modulus. As it is relative to seal geometry, it is given for different O-ring cross-sections. As a will typically only know the dimensions and hardness, the following diagrams show the relationship between hardness, compression and cross-section. The information refers to all elastomers, which is why the deformation forces are given for each hardness class. The forces required to deform elastomers during assembly of flanges, for example, can be obtained from the diagrams, and forces which affect seals on less resilient plastic parts can also be estimated.

31

O-Ring Guide Parker Hannifin O-Ring Division Europe

Deformation force (N/cm)

1 50

60

70 10

80

90

50

60

70

80

20

90

50

60

70

80

30

90

Hardness (Shore A)

2

3

4

5 6 7 8 910

20

30

d2 = 1.78 mm

50

1)

100

200

500

1000

Deformation force

O-ring compression (%)

1)

Length in cm of O-ring circumference

32

O-Ring Guide Parker Hannifin O-Ring Division Europe

1)

10

20

30

33

50

60

70

80

90

50

60

70

80

90

50

60

70

80

90

1

Hardness (Shore A)

2

3

4

20

30

50 1)

O-ring compression (%)

Length in cm of O-ring circumference

O-Ring Guide Parker Hannifin O-Ring Division Europe

Deformation force

Deformation force (N/cm)

5 6 7 8 910

d2 = 2.62 mm

100

200

500

1000

Deformation force

100 50 1 50

60

70 10

80

90

50

60

70

80

20

90

50

60

70

80

30

90

Hardness (Shore A)

2

3

4

5 6 7 8 910

20

30

d2 = 3.53 mm

Deformation force (N/cm)1)

200

500

1000

Deformation force

O-ring compression (%)

1)

Length in cm of O-ring circumference

34

O-Ring Guide Parker Hannifin O-Ring Division Europe

1)

10

20

30

35

50

60

70

80

90

50

60

70

80

90

50

60

70

80

90

1

Hardness (Shore A)

2

3

4

20

30

50

O-ring compression (%)

Length in cm of O-ring circumference

O-Ring Guide Parker Hannifin O-Ring Division Europe

Deformation force

Deformation force (N/cm)1)

5 6 7 8 910

d2 = 5.33 mm

100

200

500

1000

Deformation force

50 1 50

60

70 10

80

90

50

60

70

80

20

90

50

60

70

80

30

90

Hardness (Shore A)

2

3

4

5 6 7 8 910

20

30

d2 = 6.99 mm

Deformation force (N/cm)1)

100

200

500

1000

Deformation force

O-ring compression (%)

1)

Length in cm of O-ring circumference

36

O-Ring Guide Parker Hannifin O-Ring Division Europe

Extrusion

600 Diagram for selection of O-ring hardness — static seal

400 300

100

Extrusion

80 60

Deformation force

Working pressure (bar)

200

40 No extrusion

30

20

Hardness (Shore A)

80

70

90

10 8

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

Total diameteral clearance (mm)1) Basis for curves • 100,000 pressure cycles at the rate of 60 per minute from zero to the indicated pressure • Maximum temperature (i.e., test temperature) 70 °C • No back-up rings • Total diametral clearance must include cylinder expansion due to pressure. • Apply a reasonable safety factor in practical applications to allow for excessively sharp edges and other imperfections and for higher temperatures.

1)

Reduce the clearance shown by 60 % when using silicone or fluorosilicone elastomers.

37

O-Ring Guide Parker Hannifin O-Ring Division Europe

38

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation The following charts are included to facilitate engineering analysis. Additional information is available in the Parker O-Ring Handbook. Parker offers O-rings for use in static as well as dynamic sealing applications. Static seals are those where the mating parts of the gland do not have movement relative to each other. These seals include face, radial, dovetail. Examples of these seals and the corresponding design charts are found on the following pages. Dynamic seals include reciprocating, floating pneumatic, oscillating, and rotary applications. Dynamic seals are defined by one of the gland parts having movement relative to the other part. Gland design recommendations for a reciprocating seal are provided also in this chapter.

Forms of installation

For further design assistance and recommendations a Parker O-ring applications engineer.

39

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation

Static seal – axial The O-ring is deformed in the axial direction. Under pressure the O-ring is subjected to a relative movement, it is important to note the pressure direction. • If pressure acts from inside, then the O-rings outside diameter should be in with the gland outside diameter (optimally compressed between 1 and 3 % of circumference). h+ 0 . 1 B A r2 r1

0° to 5° B

b

O d7 H 11

Pressure from inside

• If pressure acts from outside, then the O-rings inside diameter should be in with the internal diameter of the gland (up to 6 % stretched). h+ 0 . 1 B A

Pressure from outside 0° to 5° B

r1

r2

b

O d8 H 11

40

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation

d2

d1

d2

h+0.1

b+0.2

r1

r2

1.50

1.10

1.9

0.2 - 0.4

0.2 - 0.4

1.78

1.30

2.4

0.2 - 0.4

0.2 - 0.4

2.00

1.50

2.6

0.2 - 0.4

0.2 - 0.4

2.50

2.00

3.2

0.2 - 0.4

0.2 - 0.4

2.62

2.10

3.6

0.2 - 0.4

0.2 - 0.4

3.00

2.30

3.9

0.4 - 0.8

0.2 - 0.4

3.53

2.80

4.8

0.4 - 0.8

0.2 - 0.4

4.00

3.25

5.2

0.4 - 0.8

0.2 - 0.4

5.00

4.00

6.5

0.4 - 0.8

0.2 - 0.4

5.33

4.35

7.2

0.4 - 0.8

0.2 - 0.4

6.00

5.00

7.8

0.4 - 0.8

0.2 - 0.4

6.99

5.75

9.6

0.8 - 1.2

0.2 - 0.4

8.00

6.80

10.4

0.8 - 1.2

0.2 - 0.4

9.00

7.70

11.7

0.8 - 1.2

0.2 - 0.4

10.00

8.70

13.0

0.8 - 1.2

0.2 - 0.4

12.00

10.60

15.6

0.8 - 1.2

0.2 - 0.4

Surface roughness – static seal

1)

Surface

Pressure

Surface roughness in μm. load area tp > 50 % Rmax. Ra

A area

non-pulsating

1.6

A area

pulsating

0.8

6.3

B Gland diameter and sides

non-pulsating

3.2

12.5

B Gland diameter and sides

pulsating

1.6

6.3

6.3

The ISO/DIN recommendations are preferred and are shown here in heavy print.

41

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation

Rectangular gland dimensions – axial deformation1)

Forms of installation

Static seal – radial r2

b + 0.2

r1

B

rounded and flash free

B O d 9 f7

A

O d3 h9

O d4 H 8

t C 15° to 20° 0° to 5°

Z

Gland in inside element

b+0.2

r1

B

r2 15° to 20° A

t C O d10 H 8

O d5 f7

Od6 H 9 B rounded and flash free Z

0° to 5°

Gland in outside element

42

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation

d2

d1

d2

t1)

b+0.2

z

r1

r2

1.50

1.10

1.9

1.5

0.2 - 0.4

0.1 - 0.3

1.78

1.40

2.4

1.5

0.2 - 0.4

0.1 - 0.3

2.00

1.50

2.6

1.5

0.2 - 0.4

0.1 - 0.3

2.50

2.00

3.2

1.5

0.2 - 0.4

0.1 - 0.3

2.62

2.20

3.6

1.5

0.2 - 0.4

0.1 - 0.3

3.00

2.30

3.9

2.0

0.4 - 0.8

0.1 - 0.3

3.53

2.90

4.8

2.0

0.4 - 0.8

0.1 - 0.3

4.00

3.25

5.2

2.0

0.4 - 0.8

0.1 - 0.3

5.00

4.10

6.5

3.0

0.4 - 0.8

0.1 - 0.3

5.33

4.50

7.2

3.0

0.4 - 0.8

0.1 - 0.3

6.00

5.00

7.8

3.0

0.4 - 0.8

0.1 - 0.3

6.99

5.90

9.6

3.6

0.8 - 1.2

0.1 - 0.3

8.00

6.80

10.4

4.0

0.8 - 1.2

0.1 - 0.3

9.00

7.70

11.7

4.5

0.8 - 1.2

0.1 - 0.3

10.00

8.70

13.0

4.5

0.8 - 1.2

0.1 - 0.3

12.00

10.60

15.6

4.5

0.8 - 1.2

0.1 - 0.3

Surface finish roughness – static seal Surface

Pressure

Surface roughness in μm, load area tp > 50 % Rmax. Ra

A area

non-pulsating

1.6

A area

pulsating

0.8

3.2

B Gland diameter and sides

non-pulsating

3.2

12.5

B Gland diameter and sides

pulsating

1.6

6.3

C Surface finish of leading edge chamfer

3.2

12.5

6.3

The tolerances are taken from d3h9 + d4H8 or d5f7+d6H9.

1)

The ISO/DIN recommendations are preferred and are shown in heavy print.

43

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation

Gland dimensions – radial deformation

Forms of installation

Static seal – dovetail groove The dovetail groove form is used when it is necessary to hold an O-ring in position; e.g. during surface work, on opening and closing of tooling, where otherwise the O-ring would fall out of the gland. The machining of the gland is difficult and expensive. b B

r2 B

h

r1 Od

24°

d = d1 + d 2

Dovetail gland d = gland mean diameter • The gland width is measured before edges are deburred • The radius r2 is so selected that the O-ring is not damaged on assembly and so that the O-ring can not be trapped in the gap under high pressure.

d2

d1

44

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation Dovetail gland dimensions1) d2

h

b

r2

r1

1.78

1.25+0.05

1.40+0.1

0,1 - 0,3

0,4 - 0,6

2.62

2.05+0.05

2.10+0.1

0,1 - 0,3

0,6 - 0,8

3.53

2.80+0.05

2.85+0.1

0,1 - 0,3

0,8 - 1,0

5.33

4.55+0.08

4.35+0.1

0,1 - 0,3

1,0 - 1,3

6.99

5.85+0.08

5.85+0.1

0,1 - 0,3

1,3 - 1,6

Surface roughness Surface

Pressure

Surface roughness in μm, load area tp > 50 % Rmax. Ra

A area

non-pulsating

1.6

A area

pulsating

0.8

3.2

B Gland diameter and sides

non-pulsating

3.2

12.5

B Gland diameter and sides

pulsating

1.6

6.3

Forms of installation

6.3

45

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation

Dynamic seal – hydraulic b+0.2

r1

B

r2 15° to 20° A

t C O d10 H 7

O d5 f7

Od6 H 9 B rounded and flash free Z

0° to 5°

Rod seal – hydraulic

O d9 f7

r2

b+0.2

r1

B

rounded and flash free

B

A

O d3 h9

O d4 H 8

t C 15° to 20° 0° to 5°

Z

Piston seal – hydraulic

46

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation

d2

d1

Gland dimensions – hydraulic2) d2

t1)

b+0.2

z

r1

r2

1.50

1.30

1.9

1.5

0,2 - 0,4

0,1 - 0,3

1.78

1.45

2.4

1.5

0,2 - 0,4

0,1 - 0,3

2.00

1.70

2.6

1.5

0,2 - 0,4

0,1 - 0,3

2.50

2.10

3.3

1.5

0,2 - 0,4

0,1 - 0,3

2.62

2.20

3.6

1.5

0,2 - 0,4

0,1 - 0,3

3.00

2.60

3.9

1.8

0,4 - 0,8

0,1 - 0,3

3.53

3.05

4.8

1.8

0,4 - 0,8

0,1 - 0,3

4.00

3.50

5.3

1.8

0,4 - 0,8

0,1 - 0,3

5.00

4.45

6.7

2.7

0,4 - 0,8

0,1 - 0,3

5.33

4.65

7.1

2.7

0,4 - 0,8

0,1 - 0,3

6.00

5.40

8.0

3.6

0,4 - 0,8

0,1 - 0,3

6.99

6.20

9.5

3.6

0,4 - 0,8

0,1 - 0,3

Surface

Surface roughness in μm, load area tp > 50 % Rmax. Ra

A area

0.4

B Gland diameter and sides

1.6

1.6 6.3

C Surface finish of leading edge chamfer

3.2

12.5

The tolerances is a combination of d3h9 + d4H8 or d5f7+d6H9.

1)

2)

The ISO/DIN recommendations are preferred and are shown here in heavy print.

Additional information to gland dimensions for O-rings with anti-extrusion rings, the surface-finishroughness and the gland dimensions of the pneumatic application is available in the Parker O-Ring Handbook.

47

O-Ring Guide Parker Hannifin O-Ring Division Europe

Forms of installation

Surface-finish roughness – hydraulic

48

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts The following tables provide dimensions for standard shrinkage materials only. These correspond to AS568B dimensions. O-rings manufactured from compounds with different shrinkage rates will provide slightly different dimensions and tolerances when standard tooling is used. Custom tooling may be necessary for some compounds in order to meet AS568B dimensions and tolerances. For further information a Parker O-ring applications engineer.

Characteristics of the 2-xxx series The 2-xxx series from Parker offers the following advantages.

49

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

• ex-stock in following compounds: N0674-70 (NBR 70 Shore A) N0552-90 (NBR 90 Shore A) E0540-80 (EPDM 80 Shore A) V0747-75 (FKM 75 Shore A) • For each 2-xxx series O-ring we can offer a Parker Parbak® back-up ring to fit. This is particularly important where large clearance gaps and/or high pressures exist (see chapter Parbak® back-up ring). • O-rings of the 2-xxx series correspond to the standard ISO 3601.

Sizing charts – 2-xxx sizes 2-0xx sizes, inner diameter d2 = 1.78 mm Parker No. 2-0011) 2-0021) 2-0031) 2-004 2-005 2-006 2-007 2-008 2-009 2-010 2-011 2-012 2-013 2-014 2-015 2-016 2-017 2-018 2-019 2-020 2-021 2-022 2-023 2-024 2-025 2-026 2-027 2-028 2-029 2-030 2-031 2-032 2-033 2-034 2-035 2-036 2-037 2-038 2-039 2-040 2-041 2-042 2-043 2-044 2-045 2-046 1)

Ød Cross(mm) sect. d2 0.74 1.02 1.07 1.27 1.42 1.52 1.78 1.78 2.57 1.78 2.90 1.78 3.68 1.78 4.47 1.78 5.28 1.78 6.07 1.78 7.65 1.78 9.25 1.78 10.82 1.78 12.42 1.78 14.00 1.78 15.60 1.78 17.17 1.78 18.77 1.78 20.35 1.78 21.95 1.78 23.52 1.78 25.12 1.78 26.70 1.78 28.30 1.78 29.87 1.78 31.47 1.78 33.05 1.78 34.65 1.78 37.82 1.78 41.00 1.78 44.17 1.78 47.35 1.78 50.52 1.78 53.70 1.78 56.87 1.78 60.05 1.78 63.22 1.78 66.40 1.78 69.57 1.78 72.75 1.78 75.92 1.78 82.27 1.78 88.62 1.78 94.97 1.78 101.32 1.78 107.67 1.78

Parker No. 2-047 2-048 2-049 2-050

Ød Cross(mm) sect. d2 114.02 1.78 120.37 1.78 126.72 1.78 133.07 1.78

Please note for these sizes the different inner diameter.

50

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts – 2-xxx sizes 2-1xx sizes, inner diameter d2 = 2.62 mm Ød Cross(mm) sect. d2 1.24 2.62 2.06 2.62 2.84 2.62 3.63 2.62 4.42 2.62 5.23 2.62 6.02 2.62 7.59 2.62 9.19 2.62 10.77 2.62 12.37 2.62 13.94 2.62 15.54 2.62 17.12 2.62 18.72 2.62 20.29 2.62 21.89 2.62 23.47 2.62 25.07 2.62 26.64 2.62 28.24 2.62 29.82 2.62 31.42 2.62 32.99 2.62 34.59 2.62 36.17 2.62 37.77 2.62 39.34 2.62 40.94 2.62 42.52 2.62 44.12 2.62 45.69 2.62 47.29 2.62 48.90 2.62 50.47 2.62 52.07 2.62 53.64 2.62 55.25 2.62 56.82 2.62 58.42 2.62 59.99 2.62 61.60 2.62 63.17 2.62 64.77 2.62 66.34 2.62 67.95 2.62

Parker No. 2-148 2-149 2-150 2-151 2-152 2-153 2-154 2-155 2-156 2-157 2-158 2-159 2-160 2-161 2-162 2-163 2-164 2-165 2-166 2-167 2-168 2-169 2-170 2-171 2-172 2-173 2-174 2-175 2-176 2-177 2-178

Ød Cross(mm) sect. d2 69.52 2.62 71.12 2.62 72.69 2.62 75.87 2.62 82.22 2.62 88.57 2.62 94.92 2.62 101.27 2.62 107.62 2.62 113.97 2.62 120.32 2.62 126.67 2.62 133.02 2.62 139.37 2.62 145.72 2.62 152.07 2.62 158.42 2.62 164.77 2.62 171.12 2.62 177.47 2.62 183.82 2.62 190.17 2.62 196.52 2.62 202.87 2.62 209.22 2.62 215.57 2.62 221.92 2.62 228.27 2.62 234.62 2.62 240.97 2.62 247.32 2.62

51

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Parker No. 2-102 2-103 2-104 2-105 2-106 2-107 2-108 2-109 2-110 2-111 2-112 2-113 2-114 2-115 2-116 2-117 2-118 2-119 2-120 2-121 2-122 2-123 2-124 2-125 2-126 2-127 2-128 2-129 2-130 2-131 2-132 2-133 2-134 2-135 2-136 2-137 2-138 2-139 2-140 2-141 2-142 2-143 2-144 2-145 2-146 2-147

Sizing charts – 2-xxx sizes 2-2xx sizes, inner diameter d2 = 3.53 mm Parker No. 2-201 2-202 2-203 2-204 2-205 2-206 2-207 2-208 2-209 2-210 2-211 2-212 2-213 2-214 2-215 2-216 2-217 2-218 2-219 2-220 2-221 2-222 2-223 2-224 2-225 2-226 2-227 2-228 2-229 2-230 2-231 2-232 2-233 2-234 2-235 2-236 2-237 2-238 2-239 2-240 2-241 2-242 2-243 2-244 2-245 2-246

Ød (mm) 4.34 5.94 7.52 9.12 10.69 12.29 13.87 15.47 17.04 18.64 20.22 21.82 23.39 24.99 26.57 28.17 29.74 31.34 32.92 34.52 36.09 37.69 40.87 44.04 47.22 50.39 53.57 56.74 59.92 63.09 66.27 69.44 72.62 75.79 78.97 82.14 85.32 88.49 91.67 94.84 98.02 101.19 104.37 107.54 110.72 113.89

Crosssect. d2 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53

Parker No. 2-247 2-248 2-249 2-250 2-251 2-252 2-253 2-254 2-255 2-256 2-257 2-258 2-259 2-260 2-261 2-262 2-263 2-264 2-265 2-266 2-267 2-268 2-269 2-270 2-271 2-272 2-273 2-274 2-275 2-276 2-277 2-278 2-279 2-280 2-281 2-282 2-283 2-284

Ød (mm) 117.07 120.24 123.42 126.59 129.77 132.94 136.12 139.29 142.47 145.64 148.52 151.99 158.34 164.69 171.04 177.39 183.74 190.09 196.44 202.79 209.14 215.49 221.84 228.19 234.54 240.89 247.24 253.59 266.29 278.99 291.69 304.39 329.79 355.19 380.59 405.26 430.66 456.06

Crosssect. d2 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53 3.53

52

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts – 2-xxx sizes 2-3xx sizes, inner diameter d2 = 5.33 mm Ød (mm) 10.46 12.07 13.64 15.24 16.81 18.42 19.99 21.59 23.16 24.77 26.34 27.94 29.51 31.12 32.69 34.29 37.47 40.64 43.82 46.99 50.17 53.34 56.52 59.69 62.87 66.04 69.22 72.39 75.57 78.74 81.92 85.09 88.27 91.44 94.62 97.79 100.97 104.14 107.32 110.49 113.67 116.84 120.02 123.19 126.37 129.54

Crosssect. d2 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33

Parker No. 2-355 2-356 2-357 2-358 2-359 2-360 2-361 2-362 2-363 2-364 2-365 2-366 2-367 2-368 2-369 2-370 2-371 2-372 2-373 2-374 2-375 2-376 2-377 2-378 2-379 2-380 2-381 2-382 2-383 2-384 2-385 2-386 2-387 2-388 2-389 2-390 2-391 2-392 2-393 2-394 2-395

Ød (mm) 132.72 135.89 139.07 142.24 145.42 148.59 151.77 158.12 164.47 170.82 177.17 183.52 189.87 196.22 202.57 208.92 215.27 221.62 227.97 234.34 240.67 247.02 253.37 266.07 278.77 291.47 304.17 329.57 354.97 380.37 405.26 430.66 456.06 481.41 506.81 532.21 557.61 582.68 608.08 633.48 658.88

Crosssect. d2 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 3.53 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33 5.33

53

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Parker No. 2-309 2-310 2-311 2-312 2-313 2-314 2-315 2-316 2-317 2-318 2-319 2-320 2-321 2-322 2-323 2-324 2-325 2-326 2-327 2-328 2-329 2-330 2-331 2-332 2-333 2-334 2-335 2-336 2-337 2-338 2-339 2-340 2-341 2-342 2-343 2-344 2-345 2-346 2-347 2-348 2-349 2-350 2-351 2-352 2-353 2-354

Sizing charts – 2-xxx sizes 2-4xx sizes, inner diameter d2 = 6.99 mm Parker No. 2-425 2-426 2-427 2-428 2-429 2-430 2-431 2-432 2-433 2-434 2-435 2-436 2-437 2-438 2-439 2-440 2-441 2-442 2-443 2-444 2-445 2-446 2-447 2-448 2-449 2-450 2-451 2-452 2-453 2-454 2-455 2-456 2-457 2-458 2-459 2-460 2-461 2-462 2-463 2-464 2-465 2-466 2-467 2-468 2-469 2-470

Ød (mm) 113.67 116.84 120.02 123.19 126.37 129.54 132.72 135.89 139.07 142.24 145.42 148.59 151.77 158.12 164.47 170.82 177.17 183.52 189.87 196.22 202.57 215.27 227.97 240.67 253.37 266.07 278.77 291.47 304.17 316.87 329.57 342.27 354.97 367.67 380.37 393.07 405.26 417.96 430.66 443.36 456.06 468.76 481.46 494.16 506.86 532.26

Crosssect. d2 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99 6.99

Parker No. 2-471 2-472 2-473 2-474 2-475

Ød (mm) 557.66 582.68 608.08 633.48 658.88

Crosssect. d2 6.99 6.99 6.99 6.99 6.99

54

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts – 3-xxx sizes1)

1)

Ød (mm) 6.07 7.65 8.92 10.52 11.89 13.46 16.36 19.18 21.92 23.47 25.04 26.59 29.74 34.42 37.47 53.09 59.36

Crosssect. d2 1.63 1.63 1.83 1.83 1.98 2.08 2.21 2.46 2.95 2.95 2.95 2.95 2.95 2.95 3.00 3.00 3.00

For SAE J 514 APR 80 threaded connectors, SAE J 475 (ISO R 725) screw threads

55

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Parker No. 3-902 3-903 3-904 3-905 3-906 3-907 3-908 3-910 3-911 3-912 3-913 3-914 3-916 3-918 3-920 3-928 3-932

Sizing charts – 5-xxx sizes Parker No. 5-035 5-037 5-051 5-052 5-092 5-108 5-157 5-190 5-212 5-239 5-243 5-256 5-321 5-330 5-332 5-361 5-381 5-434 5-445 5-488 5-525 5-578 5-579 5-580 5-581 5-582 5-583 5-584 5-585 5-586 5-587 5-588 5-589 5-590 5-591 5-592 5-593 5-594 5-595 5-596 5-597 5-598 5-599 5-600 5-601 5-602 5-603 5-604

Ød Cross(mm) sect. d2 45.36 3.53 51.71 3.53 1.78 1.02 6.86 1.78 701.68 6.99 4.47 1.27 33.99 2.34 3.35 1.78 9.75 1.78 14.48 2.69 15.34 2.62 17.96 2.62 39.60 3.53 42.52 5.33 42.85 3.53 67.84 3.53 88.27 6.99 180.54 6.99 210.24 6.99 316.56 2.62 425.83 3.18 2.60 1.90 3.40 1.90 4.20 1.90 4.90 1.90 5.70 1.90 6.40 1.90 7.20 1.90 8.00 1.88 8.90 1.90 8.90 2.70 10.50 2.70 12.10 2.70 13.59 2.69 15.10 2.70 16.90 2.70 18.40 2.70 18.30 3.60 19.80 3.60 21.30 3.60 23.00 3.60 24.60 3.60 26.20 3.60 27.80 3.60 29.30 3.60 30.80 3.60 32.50 3.60 34.10 3.60

Parker No. 5-605 5-606 5-612 5-613 5-614 5-615 5-616 5-617 5-618 5-643 5-664 5-670 5-673 5-676 5-683 5-686 5-690 5-701 5-702 5-703 5-704 5-705 5-716 5-805 5-816 5-843 5-850 5-976

Ød Cross(mm) sect. d2 35.60 3.60 37.30 3.60 8.74 1.78 11.10 1.78 9.93 2.62 11.91 2.62 13.11 2.62 15.88 2.62 25.81 3.53 16.51 1.14 8.13 1.78 36.50 1.78 7.75 1.88 15.49 1.47 3.10 1.60 6.30 2.39 17.30 2.40 49.20 3.53 58.74 3.53 65.09 3.53 71.44 3.53 74.61 3.53 9.19 3.00 64.39 1.78 80.31 1.78 118.72 2.62 125.09 6.60 264.79 6.60

56

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-001 6-002 6-003 6-005 6-006 6-007 6-008 6-009 6-010 6-011 6-012 6-013 6-015 6-016 6-017 6-018 6-019 6-020 6-021 6-022 6-023 6-025 6-026 6-027 6-028 6-030 6-031 6-032 6-033 6-034 6-035 6-036 6-037 6-038 6-039 6-040 6-041 6-042 6-043 6-044 6-045 6-046 6-047 6-048 6-049 6-050 6-051 6-052

Ød Cross(mm) sect. d2 6.00 2.00 8.00 2.00 10.00 2.00 15.00 2.00 16.70 1.45 18.00 3.15 21.00 2.00 47.50 4.00 9.00 1.50 7.00 1.50 9.30 2.40 89.50 3.00 42.00 1.50 13.00 2.50 20.00 2.50 3.00 1.00 4.00 1.10 2.70 1.50 3.50 1.20 24.00 2.00 27.30 2.40 101.00 3.00 137.00 3.00 40.00 2.00 7.00 2.50 73.00 3.00 70.00 3.00 118.00 2.00 13.00 1.50 29.50 1.50 4.00 1.50 22.00 2.50 30.00 3.15 6.00 1.50 19.00 2.50 15.00 1.60 17.90 1.25 16.00 3.00 15.00 3.00 17.00 2.00 72.00 3.00 38.00 2.00 35.00 2.00 30.00 2.00 27.00 2.00 24.20 3.00 50.00 2.00 7.10 1.60

Parker No. 6-053 6-054 6-055 6-056 6-058 6-059 6-060 6-061 6-063 6-065 6-066 6-067 6-069 6-070 6-072 6-074 6-075 6-076 6-078 6-079 6-080 6-082 6-083 6-084 6-085 6-086 6-087 6-088 6-089 6-090 6-091 6-092 6-094 6-095 6-096 6-097 6-099 6-100 6-101 6-102 6-103 6-104 6-105 6-106 6-107 6-108 6-109 6-110

Ød Cross(mm) sect. d2 12.00 1.50 45.00 2.00 50.00 2.50 30.00 3.00 12.30 2.40 135.00 3.23 135.00 3.43 146.00 3.23 5.35 1.50 12.00 2.00 23.00 2.50 14.00 2.50 5.00 1.50 8.30 2.40 15.00 3.20 8.00 1.50 13.00 2.00 18.00 2.00 20.00 1.50 6.00 5.00 7.00 3.00 45.00 1.50 10.00 1.50 11.00 1.50 15.00 1.80 11.00 2.00 18.00 1.50 22.00 1.50 21.00 3.50 14.00 2.00 7.50 1.50 24.80 1.50 106.00 3.00 132.00 3.00 13.50 2.75 31.00 4.50 20.00 1.30 91.00 3.00 28.00 1.50 40.60 4.00 161.00 3.00 4.00 2.00 10.00 2.50 15.00 2.50 60.00 4.10 79.60 3.20 58.00 4.00 5.00 2.00

57

Parker No. 6-112 6-113 6-114 6-115 6-116 6-118 6-119 6-120 6-121 6-122 6-123 6-124 6-125 6-126 6-128 6-129 6-130 6-132 6-133 6-134 6-135 6-136 6-137 6-138 6-139 6-140 6-141 6-142 6-143 6-146 6-147 6-148 6-149 6-150 6-151 6-152 6-153 6-154 6-155 6-156 6-157 6-158 6-159 6-160 6-161 6-162 6-163 6-164

Ød Cross(mm) sect. d2 53.00 6.50 53.00 5.00 60.00 5.00 125.00 8.00 10.00 1.00 15.00 1.50 19.50 1.50 9.00 1.80 81.00 3.00 186.44 6.99 118.50 3.00 12.00 3.00 18.00 4.00 25.30 1.60 15.00 5.00 13.23 1.78 20.00 3.00 18.00 2.50 4.70 1.90 7.50 2.50 14.30 2.40 33.00 2.00 100.00 5.00 2.50 1.30 22.00 2.00 28.00 2.00 55.00 2.00 30.70 2.00 14.00 1.50 16.00 2.00 27.00 3.00 177.00 2.00 205.00 2.00 227.00 2.00 63.00 4.00 210.00 5.00 320.00 5.33 36.30 1.78 48.00 3.00 30.00 2.50 98.00 3.00 437.00 3.00 46.02 3.53 13.75 2.80 9.00 2.50 7.30 2.70 13.10 1.60 420.00 5.00 O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – 6-xxx sizes

Sizing charts – 6-xxx sizes Parker No. 6-165 6-166 6-167 6-168 6-170 6-173 6-174 6-175 6-176 6-177 6-178 6-179 6-180 6-183 6-184 6-189 6-190 6-192 6-193 6-194 6-195 6-198 6-202 6-203 6-204 6-205 6-206 6-207 6-208 6-209 6-212 6-214 6-215 6-216 6-218 6-221 6-222 6-223 6-224 6-226 6-227 6-228 6-229 6-230 6-232 6-233 6-234 6-235

Ød Cross(mm) sect. d2 420.00 3.50 3.90 1.80 2.50 1.20 2.50 1.70 159.00 4.00 422.00 2.00 100.00 2.50 273.05 3.53 577.85 6.99 18.30 2.40 74.00 2.00 533.40 3.18 28.00 2.20 219.00 5.30 83.80 2.62 25.50 2.00 840.00 12.00 8.10 1.60 44.35 3.00 49.50 3.00 79.50 3.00 12.50 2.00 514.00 8.00 367.00 3.50 381.00 5.00 39.20 3.00 15.30 2.40 13.00 3.50 26.70 2.50 398.00 8.00 20.34 4.25 4.50 1.50 425.00 6.00 90.00 3.00 10.60 2.00 38.00 5.00 150.00 5.40 15.80 2.40 138.00 6.00 200.00 6.00 42.00 3.00 740.00 10.00 837.00 10.00 882.00 10.00 984.00 10.00 602.00 8.00 283.00 12.00 637.00 10.00

Parker No. 6-236 6-237 6-238 6-239 6-240 6-241 6-242 6-243 6-245 6-247 6-248 6-249 6-250 6-251 6-252 6-253 6-254 6-255 6-256 6-257 6-260 6-261 6-262 6-263 6-265 6-266 6-267 6-268 6-269 6-270 6-271 6-272 6-273 6-274 6-275 6-276 6-277 6-278 6-279 6-280 6-281 6-282 6-283 6-285 6-286 6-287 6-288 6-289

Ød Cross(mm) sect. d2 689.00 10.00 786.00 10.00 285.00 12.00 1029.00 10.00 1075.00 10.00 291.00 6.00 63.00 2.50 67.00 1.50 1154.00 10.00 624.00 6.99 783.00 6.99 910.00 6.99 936.00 6.99 3.70 1.90 231.50 6.00 106.80 2.66 218.00 12.00 126.00 5.00 480.06 10.00 93.39 1.47 506.00 2.62 504.00 6.99 532.00 7.00 22.70 1.50 619.50 8.00 693.50 10.10 734.00 6.99 827.00 7.00 950.50 12.06 1046.00 7.00 1103.00 10.00 69.24 3.40 196.00 12.00 115.00 3.00 20.30 2.40 88.00 3.00 8.79 1.14 622.00 8.00 810.00 7.10 1016.00 7.00 241.00 7.00 171.00 11.00 330.00 6.00 21.70 0.73 21.82 1.00 22.89 1.00 24.32 1.00 25.79 1.00

58

Parker Ød CrossNo. (mm) sect. d2 6-290 30.30 2.40 6-291 37.00 2.50 6-292 40.00 3.00 6-293 47.20 5.70 6-294 74.20 5.70 6-295 19.00 0.80 6-296 27.71 1.02 6-297 16.58 1.50 6-298 23.60 1.02 6-299 191.00 1.78 6-300 19.80 2.40 6-301 677.00 7.00 6-302 955.00 12.60 6-303 763.01 6.99 6-304 887.00 6.99 6-305 736.00 3.53 6-306 2.20 1.60 6-307 3.33 1.02 6-308 18.50 1.50 6-309 87.30 2.00 6-311 7.00 2.00 6-313 16.50 2.70 6-314 31.02 3.00 6-316 67.00 2.50 6-317 7.80 3.60 6-318 151.70 5.60 6-320 608.00 10.00 6-321 700.00 10.00 6-322 810.00 10.00 6-323 45.00 2.50 6-324 31.00 2.50 6-328 500.00 3.53 6-329 36.00 2.50 6-330 850.00 10.00 6-331 431.80 7.10 6-332 1011.00 5.33 6-333 1042.00 5.33 6-334 960.00 5.33 6-335 914.00 5.33 6-336 262.00 5.33 6-337 41.40 2.62 6-338 5.60 2.40 6-339 94.50 3.00 6-340 14.60 2.40 6-341 137.30 8.00 6-342 204.00 8.00 6-343 21.50 1.78 6-344 6.20 1.50 O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker Ød CrossNo. (mm) sect. d2 6-345 8.20 1.50 6-346 9.40 2.10 6-347 11.40 2.10 6-348 13.40 2.10 6-349 15.40 2.10 6-350 19.40 2.10 6-351 23.70 2.80 6-352 29.70 2.80 6-353 38.70 2.80 6-354 46.70 2.80 6-356 22.10 1.60 6-360 19.00 2.00 6-361 3.30 2.40 6-363 865.00 12.00 6-364 1.98 0.84 6-366 11.89 1.78 6-367 17.81 1.02 6-369 1.50 1.00 6-370 48.00 2.00 6-372 720.00 6.99 6-373 9.53 1.60 6-374 6.30 1.60 6-375 10.25 1.40 6-376 25.00 5.00 6-377 35.00 5.30 6-379 138.00 2.10 6-380 594.51 7.14 6-381 647.70 6.99 6-382 20.20 3.00 6-385 1071.00 14.40 6-387 25.80 3.30 6-388 17.40 2.50 6-389 723.90 6.99 6-390 8.00 3.00 6-392 99.00 6.99 6-393 1060.00 10.00 6-394 514.00 8.00 6-395 9.35 1.60 6-396 18.20 3.00 6-397 14.50 1.60 6-400 27.00 1.50 6-401 4.50 1.00 6-402 3.50 1.25 6-404 19.00 5.00 6-405 93.50 9.50 6-407 242.00 6.00 6-408 0.80 1.60 6-409 940.00 10.00

Parker No. 6-411 6-412 6-413 6-414 6-415 6-416 6-417 6-418 6-420 6-421 6-422 6-423 6-425 6-426 6-427 6-428 6-430 6-431 6-432 6-433 6-434 6-435 6-436 6-437 6-438 6-439 6-440 6-441 6-442 6-443 6-444 6-445 6-446 6-447 6-448 6-449 6-451 6-452 6-453 6-454 6-455 6-456 6-458 6-459 6-460 6-461 6-462 6-464

Ød Cross(mm) sect. d2 60.00 2.50 238.00 5.00 100.00 4.00 41.75 2.60 800.00 5.33 65.00 5.30 760.00 5.00 1.85 1.50 4.00 2.20 112.00 3.00 607.00 4.00 46.87 2.62 18.00 3.00 25.00 4.00 57.00 3.00 4.00 2.50 21.20 2.40 44.00 2.00 7.50 2.00 38.00 2.50 51.50 1.50 48.40 4.85 240.00 12.00 8.00 1.00 12.00 1.00 16.00 1.00 6.80 2.00 3.00 1.50 25.00 2.00 24.00 6.00 159.20 5.70 82.00 4.00 94.00 2.00 58.00 2.00 119.20 5.70 41.00 3.00 129.20 5.70 85.20 9.25 24.00 4.00 30.00 4.00 62.00 2.50 84.00 3.00 400.00 12.00 37.36 2.60 996.00 7.00 213.68 7.14 558.00 10.00 76.00 4.50

59

Parker No. 6-466 6-467 6-468 6-469 6-470 6-471 6-472 6-473 6-474 6-475 6-476 6-480 6-483 6-485 6-486 6-487 6-489 6-491 6-492 6-493 6-494 6-495 6-496 6-497 6-498 6-499 6-500 6-501 6-502 6-503 6-504 6-505 6-508 6-509 6-510 6-511 6-512 6-513 6-514 6-515 6-516 6-517 6-518 6-520 6-521 6-523 6-524 6-525

Ød Cross(mm) sect. d2 188.00 4.00 528.00 8.00 3.50 1.50 330.00 8.00 9.00 2.00 11.30 2.40 33.30 2.40 13.60 2.50 63.00 4.50 10.30 2.40 17.00 1.50 6.60 1.50 74.00 3.00 225.00 5.00 7.80 4.60 2.90 1.02 21.00 6.00 3.50 1.10 174.00 3.00 22.00 1.39 162.50 3.53 190.00 3.00 151.00 3.00 27.50 1.50 90.00 2.00 18.60 2.00 66.00 2.00 65.00 2.00 220.00 3.00 19.30 2.40 120.00 3.00 270.00 3.00 849.00 7.00 819.00 7.00 315.00 6.00 140.00 3.00 144.00 3.70 82.00 2.00 250.00 3.00 134.00 3.00 230.00 3.00 335.00 3.00 355.00 3.00 8.00 2.20 716.00 8.00 65.00 3.00 17.00 1.10 41.28 3.53 O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – 6-xxx sizes

Sizing charts – 6-xxx sizes Parker Ød CrossNo. (mm) sect. d2 6-527 974.00 7.00 6-528 16.00 1.50 6-529 524.00 10.00 6-530 455.00 8.00 6-531 710.00 5.33 6-532 10.00 2.20 6-534 1004.00 8.00 6-535 680.00 5.00 6-536 635.00 5.00 6-538 2.40 1.90 6-539 70.00 4.50 6-540 33.00 2.50 6-541 41.00 2.50 6-542 44.20 2.50 6-543 6.00 1.00 6-544 24.00 1.50 6-545 35.00 4.50 6-546 205.00 3.00 6-547 197.00 3.00 6-548 5.70 3.20 6-549 3.00 1.20 6-550 12.50 1.10 6-551 10.80 1.50 6-552 70.00 2.00 6-553 304.80 1.78 6-554 17.40 2.10 6-555 37.00 5.00 6-556 52.00 3.00 6-557 18.60 3.50 6-558 87.20 2.50 6-559 137.00 14.00 6-560 59.70 7.00 6-561 88.30 7.00 6-562 16.00 2.50 6-564 8.00 2.50 6-566 40.00 2.50 6-568 56.00 2.00 6-569 80.00 2.00 6-570 215.00 6.00 6-571 10.15 1.40 6-572 6.50 2.00 6-573 19.00 1.50 6-574 86.84 5.33 6-575 39.00 2.00 6-576 160.00 3.00 6-577 130.00 6.00 6-578 445.00 8.00 6-579 87.00 3.00

Parker No. 6-580 6-581 6-582 6-583 6-584 6-585 6-586 6-587 6-588 6-589 6-592 6-593 6-594 6-595 6-596 6-597 6-598 6-600 6-601 6-602 6-603 6-604 6-605 6-606 6-607 6-608 6-609 6-610 6-611 6-612 6-613 6-614 6-615 6-618 6-619 6-621 6-622 6-623 6-626 6-627 6-628 6-629 6-630 6-631 6-632 6-633 6-634 6-635

Ød Cross(mm) sect. d2 118.31 3.53 6.50 1.50 95.50 3.53 5.00 1.20 13.00 1.00 34.40 3.10 39.40 3.10 74.40 3.10 84.40 3.10 105.00 2.00 8.00 1.25 19.20 3.00 42.00 2.50 24.00 2.50 65.00 4.50 875.00 8.00 375.00 5.34 209.20 5.70 100.00 2.00 140.00 10.00 50.00 4.00 240.00 3.00 10.00 3.00 35.00 2.50 315.00 4.00 94.20 5.70 36.00 2.20 9.00 1.20 25.00 1.50 125.00 3.00 4.00 1.00 190.00 5.00 3.00 2.00 234.32 1.78 20.00 2.00 535.46 7.24 34.00 2.80 149.20 5.70 580.00 8.00 10.10 1.00 19.30 3.65 210.00 3.00 51.00 3.00 179.00 3.00 16.00 1.25 61.00 4.50 71.00 4.50 236.00 7.00

60

Parker No. 6-636 6-638 6-640 6-642 6-641 6-643 6-644 6-645 6-646 6-647 6-648 6-649 6-650 6-651 6-652 6-653 6-654 6-655 6-656 6-657 6-659 6-660 6-661 6-662 6-663 6-665 6-666 6-667 6-668 6-669 6-670 6-671 6-672 6-673 6-674 6-676 6-677 6-678 6-682 6-683 6-684 6-686 6-687 6-688 6-689 6-690 6-692 6-693

Ød Cross(mm) sect. d2 64.00 3.00 281.00 5.00 97.00 1.50 40.00 1.50 70.00 1.50 57.00 1.50 638.89 5.44 665.00 5.00 32.00 2.70 617.00 7.00 820.00 7.00 798.00 7.00 853.00 7.00 9.00 4.00 6.00 5.20 664.00 5.00 28.00 2.50 174.20 5.70 26.00 2.00 7.00 1.00 67.00 3.00 27.00 5.00 7.50 1.25 12.00 3.80 30.00 4.65 60.00 3.00 24.00 1.00 770.00 10.00 708.00 10.00 450.00 10.00 550.00 10.00 245.00 10.00 364.00 10.00 48.20 1.78 120.00 1.50 84.00 2.50 11.50 1.00 36.00 2.00 375.00 10.00 15.00 1.00 3.20 1.02 3.20 1.60 21.50 1.50 133.35 5.33 150.00 3.00 546.00 7.00 8.50 1.50 130.00 2.50 O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-694 6-698 6-699 6-700 6-701 6-702 6-703 6-704 6-705 6-706 6-707 6-708 6-709 6-710 6-711 6-713 6-714 6-715 6-716 6-717 6-718 6-719 6-720 6-722 6-723 6-724 6-725 6-726 6-728 6-729 6-730 6-731 6-733 6-734 6-736 6-737 6-738 6-739 6-740 6-741 6-742 6-743 6-745 6-746 6-748 6-749 6-750 6-751

Ød Cross(mm) sect. d2 36.00 2.10 140.00 2.00 62.00 3.00 96.00 2.00 695.00 6.99 707.00 6.99 55.30 2.00 180.00 3.00 14.00 3.00 189.20 5.70 865.00 8.40 929.00 6.00 565.00 7.00 7.50 1.00 388.00 5.00 6.00 1.25 1.80 1.00 8.80 1.00 320.00 6.00 11.00 2.50 258.40 1.60 57.00 2.50 93.00 2.00 128.00 2.00 380.00 4.00 102.00 3.00 16.56 1.78 45.00 5.00 26.00 1.00 78.00 3.00 13.00 3.00 18.00 1.30 85.00 2.00 430.00 12.00 3.17 1.02 13.89 1.30 5.33 1.02 56.00 4.50 109.00 3.00 428.00 5.70 614.00 7.00 93.00 3.00 25.30 2.40 169.20 5.70 5.70 1.05 26.00 2.50 45.90 1.50 5.30 2.40

Parker No. 6-752 6-753 6-754 6-755 6-756 6-757 6-758 6-759 6-760 6-762 6-764 6-766 6-767 6-768 6-769 6-772 6-773 6-774 6-775 6-777 6-779 6-780 6-781 6-782 6-783 6-784 6-785 6-786 6-787 6-788 6-790 6-791 6-792 6-793 6-794 6-797 6-798 6-799 6-800 6-801 6-802 6-803 6-804 6-805 6-806 6-807 6-808 6-809

Ød Cross(mm) sect. d2 34.65 2.60 39.50 2.60 76.00 2.50 18.00 5.00 148.00 10.00 73.00 4.00 19.75 2.50 43.25 2.60 31.95 2.60 107.31 6.99 59.60 5.85 31.70 3.50 109.40 3.10 119.60 5.70 114.40 3.10 44.70 3.50 155.00 10.00 12.00 2.50 515.00 10.00 10.60 1.80 19.00 2.65 21.20 2.65 28.00 2.65 38.70 2.65 45.00 2.65 32.50 3.55 56.00 3.55 67.00 3.55 71.00 3.55 80.00 3.55 80.00 1.80 50.00 4.50 61.00 5.00 20.00 1.80 28.00 1.80 2.00 1.00 19.00 1.80 468.00 6.00 500.00 8.00 21.20 3.55 33.50 2.65 30.00 3.55 92.50 3.55 77.00 2.00 105.00 3.50 370.00 5.50 20.00 3.55 43.70 1.80

61

Parker No. 6-810 6-812 6-813 6-814 6-815 6-816 6-817 6-818 6-819 6-820 6-821 6-822 6-823 6-824 6-825 6-826 6-827 6-831 6-832 6-833 6-834 6-835 6-836 6-837 6-838 6-839 6-840 6-841 6-842 6-844 6-845 6-846 6-848 6-849 6-850 6-851 6-853 6-854 6-855 6-856 6-857 6-861 6-862 6-863 6-865 6-866 6-867 6-868

Ød Cross(mm) sect. d2 54.50 2.65 133.50 12.00 341.00 14.00 164.20 5.84 109.20 5.84 670.00 10.00 590.00 10.00 160.00 4.00 54.00 3.00 79.00 1.50 83.00 1.00 85.00 1.50 10.00 2.65 69.00 3.00 27.00 3.20 78.00 3.50 470.00 10.00 590.00 3.50 96.00 9.00 137.00 4.00 484.86 3.53 449.50 6.99 543.50 6.99 109.20 5.70 32.00 4.00 10.10 1.78 282.37 3.53 175.00 10.00 255.00 4.00 135.00 4.00 42.50 1.80 234.20 7.00 18.14 1.78 4.80 0.75 32.00 2.50 61.00 2.00 85.00 4.00 298.00 2.62 6.30 1.80 7.50 1.80 16.00 1.80 5.80 0.75 180.00 10.00 95.00 4.00 201.00 4.00 9.30 1.50 89.20 5.70 195.00 3.50 O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – 6-xxx sizes

Sizing charts – 6-xxx sizes Parker No. 6-869 6-871 6-872 6-873 6-874 6-875 6-876 6-877 6-878 6-879 6-880 6-881 6-882 6-883 6-884 6-885 6-887 6-889 6-890 6-891 6-892 6-893 6-894 6-895 6-896 6-897 6-898 6-899 6-900 6-902 6-903 6-904 6-905 6-907 6-909 6-910 6-911 6-912 6-913 6-914 6-915 6-916 6-917 6-918 6-919 6-920 6-921 6-922

Ød Cross(mm) sect. d2 32.00 2.00 260.00 5.00 150.00 4.00 112.00 4.00 95.00 5.00 41.60 2.40 16.50 1.00 22.00 4.00 245.00 3.00 54.00 4.00 2.30 1.30 37.00 3.00 45.00 1.00 60.00 1.20 68.00 3.00 80.50 4.00 172.00 3.00 174.30 3.50 870.00 8.00 16.00 2.65 400.00 5.00 52.20 5.70 27.00 2.50 359.20 13.80 257.20 14.00 380.00 6.00 429.00 6.00 70.00 5.00 83.00 3.00 130.00 5.00 110.00 3.00 13.00 1.30 28.00 1.00 6.80 1.80 449.00 12.00 10.00 2.62 165.00 2.00 49.20 3.00 27.20 3.00 34.00 3.00 110.00 5.00 25.00 2.50 296.00 6.00 234.10 8.40 515.90 6.00 195.50 12.00 76.00 3.00 7.00 1.40

Parker No. 6-924 6-925 6-927 6-928 6-929 6-930 6-931 6-932 6-933 6-934 6-935 6-936 6-937 6-938 6-939 6-940 6-941 6-942 6-943 6-944 6-945 6-946 6-947 6-948 6-949 6-950 6-951 6-952 6-953 6-954 6-955 6-956 6-957 6-958 6-959 6-960 6-961 6-963 6-964 6-965 6-966 6-967 6-968 6-969 6-970 6-971 6-972 6-973

Ød Cross(mm) sect. d2 900.00 10.00 2.06 0.66 380.00 8.00 11.50 1.50 13.30 2.40 477.00 10.50 10.00 6.50 150.00 2.00 6.40 1.30 401.71 3.53 307.57 3.53 272.64 3.53 7.00 2.35 409.00 6.99 434.00 6.99 15.30 2.20 68.00 5.00 23.60 2.90 748.50 7.00 46.00 4.00 11.50 2.50 17.00 3.00 325.00 5.33 274.00 5.33 223.00 5.33 5.50 2.00 526.00 6.99 9.50 1.00 11.00 3.00 214.63 2.18 5.00 1.75 7.10 2.00 25.60 1.93 20.00 4.00 7.00 1.20 5.61 1.68 122.00 3.00 93.00 4.00 50.00 3.00 10.40 1.00 2.50 1.00 245.00 10.85 5.50 1.50 25.00 3.00 37.00 1.50 2.80 1.90 40.82 2.59 3.50 0.80

62

Parker Ød CrossNo. (mm) sect. d2 6-974 17.00 3.50 6-975 44.83 2.67 6-976 10.50 1.50 6-977 28.00 3.00 6-978 78.00 2.50 6-979 72.00 2.50 6-980 36.00 1.50 6-982 114.00 3.00 6-983 164.20 5.70 6-984 2965.00 7.00 6-985 56.00 3.00 6-986 635.00 9.00 6-988 270.00 5.33 6-990 69.00 2.50 6-991 86.00 2.62 6-992 79.30 2.62 6-993 35.00 3.20 6-994 4.00 3.00 6-995 105.00 4.00 6-996 43.00 3.00 6-997 45.00 3.00 6-998 19.00 3.00 6-999 23.00 2.00 6-1000 29.00 3.00 6-1001 75.00 4.00 6-1002 78.00 5.00 6-1003 120.00 6.00 6-1004 172.00 6.00 6-1005 114.20 5.70 6-1007 187.10 8.40 6-1008 463.00 7.00 6-1010 249.30 5.70 6-1012 84.30 5.70 6-1013 72.00 4.00 6-1014 85.00 3.00 6-1015 132.00 4.00 6-1016 87.20 5.70 6-1017 613.92 6.99 6-1018 289.42 5.87 6-1019 2.35 1.00 6-1020 46.00 3.00 6-1021 16.00 4.00 6-1022 6.75 1.78 6-1023 40.00 5.00 6-1024 53.00 3.50 6-1025 38.00 3.50 6-1026 5.00 1.00 6-1027 24.00 3.00 O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker Ød CrossNo. (mm) sect. d2 6-1028 185.00 5.00 6-1029 94.00 4.00 6-1030 248.00 5.00 6-1031 28.00 5.00 6-1032 7.70 2.00 6-1033 2.80 1.60 6-1034 61.00 4.00 6-1035 5.00 2.50 6-1036 4.60 2.00 6-1037 65.00 5.00 6-1038 39.00 3.00 6-1039 16.30 2.40 6-1040 18.00 2.20 6-1041 47.00 2.50 6-1042 261.00 6.00 6-1043 338.00 6.00 6-1044 190.00 4.00 6-1045 162.00 2.50 6-1046 145.00 5.00 6-1047 34.00 1.00 6-1048 218.00 5.80 6-1049 14.00 1.10 6-1050 218.00 6.00 6-1051 142.00 4.00 6-1052 88.00 4.00 6-1053 65.00 4.00 6-1054 44.00 3.00 6-1055 103.00 5.00 6-1056 93.00 5.00 6-1057 80.00 4.00 6-1058 185.00 3.00 6-1059 47.00 4.00 6-1060 43.00 4.00 6-1061 92.00 4.00 6-1062 95.00 4.50 6-1063 220.00 5.00 6-1064 22.20 3.00 6-1065 55.00 3.00 6-1066 1960.00 10.85 6-1067 2072.00 10.00 6-1068 175.00 6.00 6-1069 77.10 2.62 6-1070 49.20 5.70 6-1071 755.00 5.00 6-1072 465.00 5.00 6-1073 128.00 5.00 6-1074 105.00 5.00 6-1075 75.00 3.00

Parker No. 6-1076 6-1077 6-1078 6-1079 6-1080 6-1081 6-1082 6-1083 6-1084 6-1085 6-1086 6-1087 6-1088 6-1089 6-1090 6-1091 6-1092 6-1093 6-1094 6-1095 6-1096 6-1097 6-1098 6-1099 6-1100 6-1101 6-1102 6-1103 6-1105 6-1106 6-1107 6-1108 6-1109 6-1110 6-1111 6-1112 6-1113 6-1114 6-1115 6-1116 6-1117 6-1118 6-1119 6-1120 6-1121 6-1122 6-1123 6-1124

Ød Cross(mm) sect. d2 120.00 4.00 81.00 4.00 23.00 1.50 750.00 5.00 485.00 5.00 160.00 5.00 26.00 3.00 22.00 3.00 130.00 4.00 135.00 5.00 22.30 2.40 36.20 3.00 180.00 4.00 99.20 5.70 336.00 7.00 20.00 5.00 38.00 3.00 142.00 6.00 63.00 6.00 94.00 3.00 129.00 4.00 170.00 4.00 179.20 5.70 15.00 4.00 35.00 1.50 360.00 7.50 5.69 1.14 90.00 7.00 116.50 1.78 108.00 8.00 152.00 8.00 180.52 5.33 17.20 3.00 180.00 6.00 88.00 8.00 23.00 3.00 90.00 2.50 40.00 6.00 22.00 1.30 35.00 3.00 62.00 6.00 210.00 4.00 180.00 8.00 3.00 2.70 185.00 6.00 9.00 3.00 64.20 5.70 35.15 3.15

63

Parker No. 6-1125 6-1126 6-1127 6-1128 6-1129 6-1130 6-1131 6-1132 6-1133 6-1134 6-1135 6-1136 6-1137 6-1138 6-1139 6-1140 6-1141 6-1142 6-1143 6-1144 6-1145 6-1146 6-1147 6-1148 6-1149 6-1150 6-1151 6-1152 6-1153 6-1154 6-1155 6-1156 6-1157 6-1158 6-1160 6-1162 6-1163 6-1164 6-1165 6-1166 6-1167 6-1168 6-1169 6-1170 6-1171 6-1172 6-1173 6-1174

Ød Cross(mm) sect. d2 311.00 10.00 329.00 10.00 580.50 3.53 460.00 5.34 335.00 7.00 840.50 7.00 835.50 7.00 250.00 8.00 9.52 1.78 84.00 3.50 345.00 5.00 140.00 5.00 57.00 4.00 33.00 3.00 200.00 5.00 36.00 3.00 47.00 2.00 360.00 4.00 124.00 4.00 41.00 1.50 56.00 4.00 31.50 3.15 150.00 6.00 39.40 2.10 6.50 1.20 34.40 2.10 115.00 2.00 79.20 5.70 206.00 7.00 136.00 4.00 245.00 5.00 890.00 5.00 615.00 5.00 520.00 5.00 695.00 5.00 63.00 3.50 102.00 4.00 114.00 5.00 88.00 6.00 35.00 4.00 248.00 7.00 300.00 6.00 115.00 5.00 515.00 5.00 315.00 5.00 320.62 3.53 764.00 6.99 85.00 6.00 O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – 6-xxx sizes

Sizing charts – 6-xxx sizes Parker Ød CrossNo. (mm) sect. d2 6-1175 104.50 3.00 6-1176 46.00 2.00 6-1177 172.00 4.00 6-1178 45.00 4.00 6-1179 90.00 4.00 6-1180 120.00 5.00 6-1181 80.00 5.00 6-1182 112.00 7.00 6-1183 7.50 2.10 6-1185 52.50 1.80 6-1186 55.00 4.00 6-1188 37.00 2.00 6-1189 43.00 2.00 6-1190 266.00 4.00 6-1191 290.00 5.00 6-1192 55.00 3.50 6-1193 66.00 3.00 6-1194 70.00 4.00 6-1195 45.00 4.50 6-1196 48.00 4.00 6-1197 34.00 2.00 6-1198 13.30 1.20 6-1199 125.00 4.00 6-1200 104.00 5.30 6-1201 260.00 8.00 6-1202 13.30 3.00 6-1203 30.00 2.15 6-1204 24.69 1.78 6-1205 362.00 5.00 6-1206 9.50 2.50 6-1207 142.00 12.00 6-1208 10.90 1.20 6-1209 62.00 3.53 6-1210 320.00 3.00 6-1211 228.00 3.00 6-1212 70.00 8.00 6-1213 1005.00 15.00 6-1214 90.00 5.00 6-1215 780.00 7.00 6-1216 10.00 1.60 6-1217 131.50 4.00 6-1218 340.00 4.00 6-1219 480.00 4.00 6-1220 610.00 4.00 6-1221 500.00 5.00 6-1222 770.00 7.00 6-1223 860.00 3.00 6-1224 42.00 5.00

Parker No. 6-1225 6-1226 6-1227 6-1228 6-1229 6-1230 6-1231 6-1232 6-1233 6-1234 6-1235 6-1236 6-1237 6-1238 6-1239 6-1240 6-1241 6-1242 6-1243 6-1244 6-1245 6-1246 6-1247 6-1248 6-1249 6-1250 6-1251 6-1252 6-1253 6-1254 6-1255 6-1256 6-1257 6-1258 6-1259 6-1260 6-1261 6-1262 6-1263 6-1264 6-1265 6-1266 6-1268 6-1269 6-1270 6-1271 6-1272 6-1273

Ød Cross(mm) sect. d2 222.00 7.00 50.00 5.00 252.00 4.00 8.50 2.00 564.30 6.99 10.80 1.90 260.00 4.00 26.00 1.50 145.00 4.00 52.00 2.50 336.00 5.33 11.00 1.00 100.00 8.00 194.00 14.00 238.00 14.00 285.00 14.10 385.00 14.20 415.00 14.20 480.00 14.00 585.00 14.00 735.00 15.00 853.00 20.00 1.56 1.00 46.00 5.00 7.30 3.40 225.00 3.00 6.36 0.72 21.00 4.00 49.00 2.00 368.00 6.00 343.00 6.00 440.00 4.00 37.50 4.00 330.00 5.00 26.00 4.00 192.00 4.00 62.00 4.00 632.00 6.00 246.00 4.00 2.20 1.00 90.00 4.80 7.30 2.40 6.30 2.40 1.50 0.60 80.00 3.00 56.70 3.00 68.00 4.00 66.00 5.00

64

Parker Ød CrossNo. (mm) sect. d2 6-1274 54.00 2.00 6-1275 11.60 2.20 6-1276 19.00 1.00 6-1277 135.00 3.00 6-1278 299.50 5.00 6-1279 273.60 5.00 6-1280 180.00 5.00 6-1281 125.00 2.50 6-1282 238.00 10.00 6-1283 195.00 5.00 6-1286 8.65 2.80 6-1287 4.00 1.80 6-1288 14.00 1.00 6-1289 24.50 3.15 6-1290 170.00 5.00 6-1291 4.50 2.25 6-1292 160.00 6.00 6-1293 230.00 8.00 6-1294 155.00 3.00 6-1295 150.00 5.00 6-1296 130.00 3.00 6-1297 9.50 2.00 6-1298 17.86 2.62 6-1299 540.00 5.00 6-1300 579.00 5.00 6-1301 602.00 5.00 6-1302 216.00 4.00 6-1303 99.00 3.00 6-1304 1840.00 5.00 6-1305 100.00 3.00 6-1306 97.00 5.00 6-1307 200.00 4.00 6-1308 640.00 6.00 6-1309 740.00 6.00 6-1310 300.00 10.00 6-1311 21.00 3.00 6-1312 6.00 1.52 6-1313 11.50 2.00 6-1314 9.50 1.78 6-1315 22.00 2.10 6-1316 80.00 3.50 6-1317 53.80 4.00 6-1318 155.00 4.00 6-1319 42.00 4.00 6-1320 107.00 8.00 6-1321 7.10 3.60 6-1322 116.00 3.00 6-1323 11.60 1.20 O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker Ød CrossNo. (mm) sect. d2 6-1324 155.00 5.00 6-1325 1865.00 5.00 6-1326 410.00 6.00 6-1327 6.00 2.50 6-1328 383.60 5.00 6-1329 134.00 8.00 6-1330 12.00 10.60 6-1331 272.00 8.00 6-1332 32.00 3.00 6-1333 51.94 3.53 6-1334 340.00 10.00 6-1335 412.00 8.00 6-1336 167.50 3.50 6-1337 11.10 1.82 6-1338 23.80 2.40 6-1339 13.70 2.50 6-1340 15.50 2.60 6-1341 17.20 1.82 6-1342 14.00 1.82 6-1343 48.20 3.00 6-1345 14.00 1.60 6-1346 240.00 5.00 6-1347 53.00 2.00 6-1348 73.00 7.00 6-1349 44.30 5.70 6-1350 104.30 5.70 6-1351 309.30 5.70 6-1352 419.30 5.70 6-1353 21.00 1.00 6-1354 58.00 3.00 6-1356 175.00 5.00 6-1357 75.00 2.50 6-1358 0.90 0.53 6-1359 304.80 3.18 6-1360 236.00 6.00 6-1361 12.10 1.60 6-1362 39.20 5.70 6-1363 3.90 2.40 6-1364 17.50 4.00 6-1365 17.00 4.00 6-1366 30.00 5.00 6-1367 110.00 2.50 6-1368 60.00 4.50 6-1369 76.00 2.00 6-1370 300.00 8.00 6-1371 310.00 5.00 6-1372 65.00 1.80 6-1373 20.00 2.65

Parker No. 6-1374 6-1375 6-1376 6-1377 6-1378 6-1379 6-1380 6-1381 6-1384 6-1385 6-1386 6-1387 6-1388 6-1389 6-1390 6-1391 6-1392 6-1393 6-1394 6-1395 6-1396 6-1398 6-1399 6-1400 6-1401 6-1402 6-1403 6-1404 6-1405 6-1406 6-1407 6-1408 6-1409 6-1410 6-1411 6-1413 6-1414 6-1415 6-1416 6-1417 6-1418 6-1419 6-1420 6-1421 6-1422 6-1423 6-1424 6-1425

Ød Cross(mm) sect. d2 395.00 12.00 21.20 1.80 11.20 1.80 65.00 2.65 28.20 1.00 12.50 1.80 68.00 3.50 105.00 3.00 240.66 7.40 5.60 1.80 11.00 3.40 390.00 4.00 256.00 4.00 38.00 1.50 155.00 3.53 192.00 8.00 354.96 6.09 14.70 3.50 5.15 1.80 100.00 6.00 15.08 2.62 15.00 3.50 42.00 4.50 7.00 2.75 31.00 2.00 165.00 4.00 265.00 5.00 325.00 5.00 4.05 1.77 85.00 6.99 9.50 1.80 331.50 6.00 534.00 8.00 1.00 0.63 33.00 3.50 43.00 5.50 35.00 5.00 97.00 4.00 8.10 2.00 77.00 2.50 661.00 14.00 62.00 1.50 500.00 6.00 115.00 6.00 7.65 2.00 29.00 2.50 297.00 4.00 220.00 7.00

65

Parker No. 6-1426 6-1427 6-1428 6-1429 6-1430 6-1431 6-1434 6-1435 6-1436 6-1437 6-1438 6-1439 6-1443 6-1444 6-1445 6-1446 6-1447 6-1448 6-1449 6-1450 6-1451 6-1452 6-1453 6-1454 6-1456 6-1457 6-1458 6-1460 6-1461 6-1462 6-1463 6-1464 6-1465 6-1466 6-1467 6-1468 6-1469 6-1470 6-1471 6-1472 6-1473 6-1474 6-1475 6-1476 6-1477 6-1478 6-1480 6-1481

Ød Cross(mm) sect. d2 238.00 6.00 120.00 10.00 185.00 4.00 91.00 2.00 19.35 1.00 23.00 4.00 5.00 1.60 440.00 4.30 131.00 5.30 50.00 3.50 54.70 3.53 61.70 4.50 675.00 5.30 490.00 5.00 85.00 5.00 21.30 2.30 27.00 2.70 55.00 5.00 10.00 8.00 198.00 4.00 235.00 4.00 92.00 3.00 195.00 6.00 11.50 2.30 24.60 3.40 86.00 4.00 320.00 6.50 10.20 1.50 31.57 1.98 70.00 2.50 19.50 3.50 14.50 3.00 20.50 2.00 12.00 1.30 77.50 2.62 11.75 1.55 12.00 1.40 21.00 1.50 6.00 1.80 82.00 3.00 128.00 3.00 30.00 2.25 78.00 2.00 275.00 5.00 285.00 5.00 31.00 1.50 17.70 1.78 8.56 1.07 O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – 6-xxx sizes

Sizing charts – 6-xxx sizes Parker No. 6-1482 6-1483 6-1484 6-1485 6-1486 6-1487 6-1488 6-1489 6-1490 6-1491 6-1493 6-1494 6-1495 6-1497 6-1498 6-1499 6-1500 6-1501 6-1502 6-1503 6-1505 6-1506 6-1507 6-1508 6-1510 6-1511 6-1513 6-1516 6-1517 6-1518 6-1520 6-1521 6-1522 6-1523 6-1524 6-1525 6-1528 6-1529 6-1530 6-1531 6-1532 6-1533 6-1534 6-1536 6-1537 6-1538 6-1539 6-1540

Ød Cross(mm) sect. d2 39.00 5.00 47.00 5.50 13.00 1.58 11.80 2.65 42.00 1.00 9.20 2.70 5.00 1.90 50.20 3.00 20.50 3.00 10.10 1.60 16.50 2.00 15.70 2.50 1.45 1.75 40.00 4.00 11.50 1.80 9.60 2.00 7.52 3.51 5.46 0.89 9.78 1.27 12.83 1.27 10.78 2.62 1.42 1.58 92.20 2.62 88.50 6.50 11.10 2.15 9.50 2.15 54.00 1.50 11.00 1.60 29.10 1.60 10.00 1.20 44.35 2.58 450.00 2.62 255.00 5.00 7.10 1.37 16.30 1.40 11.10 1.60 621.00 8.50 165.00 5.00 9.10 1.60 9.10 1.65 3.50 1.35 28.00 4.00 245.00 7.00 11.30 2.20 14.20 1.90 7.60 1.90 8.55 1.75 27.50 2.00

Parker No. 6-1541 6-1543 6-1545 6-1546 6-1547 6-1555 6-1556 6-1558 6-1559 6-1560 6-1562 6-1563 6-1564 6-1565 6-1566 6-1567 6-1568 6-1570 6-1571 6-1573 6-1575 6-1576 6-1577 6-1578 6-1579 6-1580 6-1581 6-1582 6-1583 6-1584 6-1585 6-1586 6-1587 6-1588 6-1589 6-1590 6-1591 6-1592 6-1593 6-1594 6-1599 6-1600 6-1601 6-1602 6-1605 6-1607 6-1608 6-1609

Ød Cross(mm) sect. d2 15.50 1.50 18.80 1.90 24.50 1.00 328.00 6.99 39.00 2.5 14.00 2.20 32.00 1.50 7.00 1.47 136.00 3.00 221.00 1.78 8.00 1.60 198.00 8.00 240.00 8.00 205.00 5.00 12.00 1.20 12.50 1.50 3.80 1.90 7.50 3.00 13.50 1.50 86.50 4.00 11.50 1.78 14.00 1.30 736.60 5.00 31.00 4.00 16.50 1.50 110.00 1.50 6.07 1.30 250.00 10.00 350.00 10.00 430.00 16.00 59.20 5.70 18.00 10.00 52.00 1.00 65.00 1.00 38.00 1.00 21.50 1.00 129.00 1.50 142.90 3.20 165.10 3.20 152.40 3.20 28.30 3.10 35.40 3.25 42.40 4.25 54.40 4.25 156.00 4.00 67.00 4.00 538.00 6.00 74.60 3.53

66

Parker No. 6-1610 6-1611 6-1612 6-1613 6-1614 6-1615 6-1625 6-1627 6-1628 6-1629 6-1630 6-1631 6-1632 6-1633 6-1634 6-1635 6-1636 6-1637 6-1638 6-1639 6-1640 6-1641 6-1642 6-1643 6-1644 6-1645 6-1648 6-1650 6-1651 6-1652 6-1654 6-1655 6-1656 6-1657 6-1658 6-1659 6-1660 6-1661 6-1662 6-1663 6-1664 6-1665 6-1666 6-1667 6-1668 6-1671 6-1672 6-1673

Ød Cross(mm) sect. d2 17.64 2.00 23.47 2.40 164.00 2.00 27.00 1.40 33.00 5.00 0.83 1.63 154.60 1.78 30.00 1.00 73.00 2.00 88.00 5.00 122.00 6.00 34.00 2.50 145.00 2.50 47.00 3.00 32.50 3.00 11.80 1.80 13.00 1.80 9.55 1.75 20.95 2.62 351.21 4.00 10.00 4.00 546.00 2.62 7.60 2.10 54.00 3.15 110.00 3.50 3.40 1.50 10.00 1.25 35.50 4.00 112.00 2.50 36.00 5.00 224.00 6.00 26.50 4.00 9.86 1.78 53.50 2.00 14.40 2.00 171.45 3.20 115.00 5.33 64.00 4.00 77.50 2.00 294.00 3.00 1.33 1.61 94.00 5.70 58.00 3.75 278.99 2.62 246.00 3.00 110.00 6.00 93.40 2.57 95.00 3.00 O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-1674 6-1675 6-1676 6-1677 6-1678 6-1679 6-1680 6-1684 6-1694 6-1695 6-1696 6-1698 6-1699 6-1700 6-1701 6-1702 6-1703 6-1704 6-1705 6-1706 6-1707 6-1708 6-1709 6-1710 6-1711 6-1715 6-1716 6-1717 6-1718 6-1719 6-1720 6-1721 6-1722 6-1723 6-1724 6-1725 6-1726 6-1727 6-1728 6-1729 6-1731 6-1735 6-1740 6-1742 6-1743 6-1744 6-1745 6-1747

Ød Cross(mm) sect. d2 455.00 6.00 79.50 2.65 24.50 4.00 3.80 1.50 571.00 8.00 223.00 2.65 147.60 2.65 50.30 2.50 4.30 2.40 55.00 1.20 145.00 2.88 29.00 2.00 9.80 1.50 17.00 2.50 2.50 1.60 160.00 5.30 56.50 5.30 69.20 5.30 88.40 5.30 180.00 5.30 320.00 3.53 98.00 2.50 55.00 2.50 23.30 1.60 37.50 1.80 83.00 4.00 635.00 10.00 12.30 1.90 11.00 1.90 22.60 1.78 104.20 5.70 51.10 1.60 21.10 1.60 43.70 3.55 44.96 2.57 208.00 4.00 60.00 2.00 230.00 4.50 5.50 0.80 28.68 2.40 22.00 1.00 0.70 0.50 70.50 3.20 690.00 8.00 5.60 1.90 4.80 1.30 7.60 2.62 15.30 1.50

Parker No. 6-1748 6-1749 6-1751 6-1752 6-1753 6-1765 6-1767 6-1768 6-1769 6-1770 6-1771 6-1772 6-1773 6-1774 6-1775 6-1776 6-1777 6-1778 6-1779 6-1780 6-1781 6-1782 6-1783 6-1784 6-1785 6-1786 6-1795 6-1797 6-1803 6-1804 6-1805 6-1806 6-1807 6-1808 6-1809 6-1810 6-1813 6-1814 6-1815 6-1816 6-1817 6-1818 6-1819 6-1822 6-1823 6-1824 6-1825 6-1826

Ød Cross(mm) sect. d2 16.00 1.90 9.96 1.53 6.10 1.60 4.30 1.30 460.00 6.99 17.00 1.93 230.00 4.80 24.50 5.50 31.50 7.00 15.50 4.00 74.50 3.00 19.50 4.00 153.50 3.20 148.60 3.20 131.10 3.20 86.00 3.20 90.80 3.50 70.00 3.50 87.60 3.00 33.00 1.50 95.00 1.50 90.00 1.50 135.00 1.50 329.57 4.80 8.73 1.78 365.00 5.30 359.53 5.33 67.39 2.26 151.39 2.57 83.77 1.78 35.96 2.32 20.20 1.81 136.53 1.78 35.95 1.78 14.23 1.60 4.32 0.92 14.47 3.53 2.95 0.97 163.07 1.63 183.00 1.78 14.20 3.00 21.20 3.60 17.20 4.00 13.00 2.62 522.00 10.00 623.08 5.33 13.30 1.80 114.55 2.57

67

Parker Ød CrossNo. (mm) sect. d2 6-1827 13.30 2.80 6-1828 14.60 2.10 6-1832 19.84 0.79 6-1833 7.40 2.62 6-1834 11.20 2.62 6-1836 362.00 4.00 6-1837 515.00 5.33 6-1838 532.18 5.33 6-1839 34.00 4.00 6-1840 745.00 10.00 6-1841 618.50 2.00 6-1842 367.89 2.66 6-1843 455.00 5.33 6-1844 595.00 5.33 6-1845 2324.00 6.99 6-1846 2350.00 6.99 6-1847 736.00 7.00 6-1848 190.00 1.78 6-1849 205.00 1.78 6-1851 425.33 5.33 6-1854 48.00 1.00 6-1855 9.70 5.33 6-1856 11.82 2.62 6-1857 14.90 2.70 6-1858 602.00 7.00 6-1859 640.00 7.00 6-1860 259.20 3.53 6-1861 245.00 3.53 6-1862 27.50 1.00 6-1863 6.00 1.20 6-1864 59.50 5.00 6-1865 164.33 2.62 6-1866 206.00 5.70 6-1867 215.00 5.00 6-1868 270.00 6.00 6-1869 19.50 2.66 6-1873 11.50 3.00 6-1875 21.50 1.60 6-1876 67.00 2.80 6-1877 11.00 2.30 6-1879 8.15 1.83 6-1880 313.00 5.33 6-1881 340.00 5.33 6-1883 2.00 1.50 6-1885 22.00 2.30 6-1886 7.10 1.84 6-1888 355.00 8.00 6-1889 74.90 1.78 O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – 6-xxx sizes

Sizing charts – 6-xxx sizes Parker No. 6-1890 6-1892 6-1893 6-1895 6-1896 6-1897 6-1903 6-1904 6-1905 6-1906 6-1907 6-1908 6-1909 6-1910 6-1911 6-1912 6-1913 6-1914 6-1915 6-1916 6-1917 6-1918 6-1919 6-1920 6-1922 6-1923 6-1924 6-1925 6-1926 6-1927 6-1928 6-1929 6-1930 6-1931 6-1932 6-1933 6-1934 6-1936 6-1937 6-1939 6-1942 6-1943 6-1944 6-1945 6-1947 6-1948 6-1949 6-1950

Ød Cross(mm) sect. d2 34.00 1.10 5.96 1.70 9.11 2.00 239.20 3.53 226.20 3.53 45.00 6.00 43.00 3.50 90.00 5.50 100.00 5.50 30.00 3.50 45.00 3.50 68.00 5.50 72.00 5.50 95.00 5.50 23.00 2.62 40.00 3.50 47.00 5.00 53.00 4.00 28.00 3.50 75.00 4.50 70.00 5.50 349.00 5.33 27.00 2.80 32.00 3.50 11.30 4.75 14.20 2.00 3.30 1.78 4.09 1.78 35.00 3.50 65.00 5.50 75.00 5.50 168.40 6.00 23.40 4.00 49.50 5.00 197.00 6.00 133.00 3.00 469.00 5.33 13.30 2.20 428.00 5.00 5.70 2.62 126.30 5.33 818.00 12.00 777.00 12.00 224.00 7.00 334.00 2.62 230.00 5.00 137.50 3.30 77.80 1.50

Parker No. 6-1951 6-1952 6-1953 6-1956 6-1957 6-1958 6-1959 6-1960 6-1961 6-1962 6-1963 6-1964 6-1966 6-1967 6-1969 6-1974 6-1975 6-1977 6-1978 6-1979 6-1980 6-1981 6-1982 6-1985 6-1990 6-1991 6-1993 6-1994 6-2000 6-2005 6-2008 6-2009 6-2012 6-2013 6-2015 6-2018 6-2019 6-2020 6-2021 6-2022 6-2023 6-2032 6-2033 6-2034 6-2036 6-2037 6-2038 6-2039

Ød Cross(mm) sect. d2 764.00 7.00 555.00 3.00 589.00 3.00 786.00 4.00 522.00 4.00 372.00 4.00 645.00 4.00 645.00 3.53 17.30 2.20 128.00 4.00 587.00 7.00 560.00 7.00 69.00 4.50 13.00 1.20 1.10 0.25 66.00 1.50 19.30 2.20 8.50 3.00 11.80 3.00 484.00 8.40 36.00 4.00 50.00 1.50 3.20 1.78 58.00 2.50 125.00 3.50 52.39 3.53 250.00 4.00 16.82 5.33 135.50 6.00 276.00 2.62 45.30 1.93 855.00 10.00 74.00 2.50 335.00 5.00 470.00 4.50 43.00 5.00 58.00 3.55 38.00 4.00 148.00 2.50 150.00 2.50 598.00 7.00 6.40 2.62 78.00 1.50 10.24 1.83 109.50 5.33 297.80 6.99 16.00 3.50 22.22 2.62

68

Parker No. 6-2040 6-2041 6-2042 6-2043 6-2044 6-2045 6-2046 6-2047 6-2051 6-2052 6-2053 6-2054 6-2055 6-2064 6-2065 6-2066 6-2067 6-2068 6-2069 6-2070 6-2071 6-2073 6-2074 6-2075 6-2077 6-2078 6-2079 6-2080 6-2081 6-2082 6-2083 6-2084 6-2087 6-2088 6-2090 6-2093 6-2094 6-2096 6-2097 6-2098 6-2099 6-2100 6-2101 6-2102 6-2104 6-2105 6-2107 6-2108

Ød Cross(mm) sect. d2 26.00 3.50 4.45 3.53 801.00 4.00 14.00 5.00 18.00 3.50 63.00 3.00 130.00 5.80 34.50 2.65 212.00 5.30 48.00 2.30 6.00 2.10 36.60 2.90 20.80 2.00 121.00 8.00 510.00 3.00 820.00 3.00 750.00 3.00 17.10 1.60 12.30 3.50 14.60 2.95 11.00 3.50 492.00 3.53 48.00 2.10 74.50 4.00 70.00 7.00 3.50 1.00 68.00 2.50 300.00 5.00 29.20 5.05 22.40 2.50 41.50 2.00 188.14 1.78 18.00 1.80 42.00 2.00 45.69 1.78 8.00 2.65 15.22 1.78 74.90 2.00 3.10 1.20 193.70 7.00 1.90 2.80 12.00 5.00 11.56 1.78 16.40 1.78 74.00 4.50 34.00 1.50 123.00 3.00 89.00 1.90 O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts – 6-xxx sizes

69

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Parker Ød CrossNo. (mm) sect. d2 6-2109 312.90 1.78 6-2111 310.00 2.62 6-2112 14.60 1.50 6-2113 49.88 1.78 6-2114 285.00 6.00 6-2117 54.00 4.50 6-2118 60.40 3.00 6-2119 42.50 3.53 6-2120 69.60 5.00 6-2121 104.00 5.00 6-2122 84.50 3.00 6-2123 4.45 3.00 6-2124 1020.00 5.70 6-2125 165.30 1.78 6-2127 7.77 3.77 6-2128 9.75 1.50 6-2129 150.00 5.30 6-2130 32.00 1.78 6-2131 169.98 3.56 6-2132 63.10 3.53 6-2133 36.00 1.78 6-2134 300.00 4.00 6-2135 14.10 2.40 6-2137 27.60 2.40 6-2138 3.50 0.90 6-2139 23.80 1.50 6-2140 295.00 6.00 6-2143 53.00 3.55 6-2145 235.00 6.00 6-2146 260.00 6.00 6-2147 29.20 5.00 6-2148 29.20 4.95 6-2149 143.00 1.45 6-2150 22.00 6.00

Sizing charts – 6-xxx sizes Parker No. 6-1735 2-001 6-408 6-1615 6-1358 6-1410 2-002 6-1969 2-102 6-1664 2-003 6-1506 6-1495 6-1269 6-369 6-1247 5-051 2-004 6-714 6-418 6-2099 6-364 6-797 6-1883 6-925 2-103 6-1264 6-306 6-880 6-1019 6-538 6-966 6-167 6-138 6-1701 6-168 2-005 5-578 6-020 6-1033 6-971 2-104 6-487 2-006 6-1814 6-018 6-549 6-441 6-615 6-1120

Ød Crossmm sect. d2 0.70 0.50 0.74 1.02 0.80 1.60 0.83 1.63 0.90 0.53 1.00 0.63 1.07 1.27 1.10 0.25 1.24 2.62 1.33 1.61 1.42 1.52 1.42 1.58 1.45 1.75 1.50 0.60 1.50 1.00 1.56 1.00 1.78 1.02 1.78 1.78 1.80 1.00 1.85 1.50 1.90 2.80 1.98 0.84 2.00 1.00 2.00 1.50 2.06 0.66 2.06 2.62 2.20 1.00 2.20 1.60 2.30 1.30 2.35 1.00 2.40 1.90 2.50 1.00 2.50 1.20 2.50 1.30 2.50 1.60 2.50 1.70 2.57 1.78 2.60 1.90 2.70 1.50 2.80 1.60 2.80 1.90 2.84 2.62 2.90 1.02 2.90 1.78 2.95 0.97 3.00 1.00 3.00 1.20 3.00 1.50 3.00 2.00 3.00 2.70

Parker No. 6-2097 5-683 6-736 6-684 6-686 6-1982 6-1924 6-361 6-307 5-190 6-1645 5-579 6-973 6-2138 6-2078 6-491 6-021 6-402 6-1532 6-468 2-105 2-007 6-251 6-1677 6-1568 6-166 6-1363 6-613 6-019 6-035 6-1287 6-104 6-420 6-428 6-994 6-1405 6-1925 5-580 6-1752 6-1694 6-1810 2-201 2-106 6-2123 6-2041 5-108 2-008 6-401 6-214 6-1291

Ød Crossmm sect. d2 3.10 1.20 3.10 1.60 3.17 1.02 3.20 1.02 3.20 1.60 3.20 1.78 3.30 1.78 3.30 2.40 3.33 1.02 3.35 1.78 3.40 1.50 3.40 1.90 3.50 0.80 3.50 0.90 3.50 1.00 3.50 1.10 3.50 1.20 3.50 1.25 3.50 1.35 3.50 1.50 3.63 2.62 3.68 1.78 3.70 1.90 3.80 1.50 3.80 1.90 3.90 1.80 3.90 2.40 4.00 1.00 4.00 1.10 4.00 1.50 4.00 1.80 4.00 2.00 4.00 2.20 4.00 2.50 4.00 3.00 4.05 1.77 4.09 1.78 4.20 1.90 4.30 1.30 4.30 2.40 4.32 0.92 4.34 3.53 4.42 2.62 4.45 3.00 4.45 3.53 4.47 1.27 4.47 1.78 4.50 1.00 4.50 1.50 4.50 2.25

Parker No. 6-1036 6-133 6-849 6-1744 5-581 6-1026 6-583 6-069 6-1434 6-955 6-1488 6-110 6-1035 6-1394 2-107 2-009 6-751 6-738 6-063 6-1501 6-1728 6-968 6-950 6-1385 6-1743 6-338 6-960 6-1102 6-748 5-582 6-1939 6-548 6-861 2-202 6-1892 6-543 6-1863 6-713 6-038 6-1312 6-1471 6-001 6-2053 6-1327 6-079 6-652 2-108 6-1581 3-902 2-010

Ød Crossmm sect. d2 4.60 2.00 4.70 1.90 4.80 0.75 4.80 1.30 4.90 1.90 5.00 1.00 5.00 1.20 5.00 1.50 5.00 1.60 5.00 1.75 5.00 1.90 5.00 2.00 5.00 2.50 5.15 1.80 5.23 2.62 5.28 1.78 5.30 2.40 5.33 1.02 5.35 1.50 5.46 0.89 5.50 0.80 5.50 1.50 5.50 2.00 5.60 1.80 5.60 1.90 5.60 2.40 5.61 1.68 5.69 1.14 5.70 1.05 5.70 1.90 5.70 2.62 5.70 3.20 5.80 0.75 5.94 3.53 5.96 1.70 6.00 1.00 6.00 1.20 6.00 1.25 6.00 1.50 6.00 1.52 6.00 1.80 6.00 2.00 6.00 2.10 6.00 2.50 6.00 5.00 6.00 5.20 6.02 2.62 6.07 1.30 6.07 1.63 6.07 1.78

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

70

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-1751 6-344 6-374 6-855 5-686 6-1268 6-1251 6-933 5-583 6-2032 6-1149 6-581 6-572 6-480 6-1022 6-907 6-440 5-052 6-657 6-959 6-922 6-1558 6-011 6-311 6-937 6-028 6-1400 6-080 6-1523 6-052 6-1886 6-956 6-1321 5-584 6-1266 6-162 6-1249 6-1833 6-710 6-661 6-091 6-856 6-432 6-1183 6-134 6-1570 6-1500 2-203 2-109 6-1538

Ød Crossmm sect. d2 6.10 1.60 6.20 1.50 6.30 1.60 6.30 1.80 6.30 2.39 6.30 2.40 6.36 0.72 6.40 1.30 6.40 1.90 6.40 2.62 6.50 1.20 6.50 1.50 6.50 2.00 6.60 1.50 6.75 1.78 6.80 1.80 6.80 2.00 6.86 1.78 7.00 1.00 7.00 1.20 7.00 1.40 7.00 1.47 7.00 1.50 7.00 2.00 7.00 2.35 7.00 2.50 7.00 2.75 7.00 3.00 7.10 1.37 7.10 1.60 7.10 1.84 7.10 2.00 7.10 3.60 7.20 1.90 7.30 2.40 7.30 2.70 7.30 3.40 7.40 2.62 7.50 1.00 7.50 1.25 7.50 1.50 7.50 1.80 7.50 2.00 7.50 2.10 7.50 2.50 7.50 3.00 7.52 3.51 7.52 3.53 7.59 2.62 7.60 1.90

Parker No. 6-1642 6-1745 3-903 2-011 6-1422 6-1032 5-673 6-2127 6-317 6-486 6-437 6-592 6-074 6-1562 5-585 6-002 6-520 6-564 6-2093 6-390 6-192 6-1416 5-664 6-1879 6-345 6-070 6-692 6-1228 6-1977 6-1539 6-1481 6-1286 6-1785 5-612 6-277 6-715 5-586 5-587 3-904 6-610 6-010 6-120 6-470 6-161 6-1122 6-651 6-1530 6-1531 6-1893 2-204

Ød Crossmm sect. d2 7.60 2.10 7.60 2.62 7.65 1.63 7.65 1.78 7.65 2.00 7.70 2.00 7.75 1.88 7.77 3.77 7.80 3.60 7.80 4.60 8.00 1.00 8.00 1.25 8.00 1.50 8.00 1.60 8.00 1.88 8.00 2.00 8.00 2.20 8.00 2.50 8.00 2.65 8.00 3.00 8.10 1.60 8.10 2.00 8.13 1.78 8.15 1.83 8.20 1.50 8.30 2.40 8.50 1.50 8.50 2.00 8.50 3.00 8.55 1.75 8.56 1.07 8.65 2.80 8.73 1.78 8.74 1.78 8.79 1.14 8.80 1.00 8.90 1.90 8.90 2.70 8.92 1.83 9.00 1.20 9.00 1.50 9.00 1.80 9.00 2.00 9.00 2.50 9.00 3.00 9.00 4.00 9.10 1.60 9.10 1.65 9.11 2.00 9.12 3.53

Parker No. 2-110 5-716 6-1487 2-012 6-866 6-012 6-395 6-346 6-952 6-1314 6-1407 6-1297 6-1511 6-1206 6-1133 6-373 6-1637 6-1499 5-212 6-1855 6-2128 6-1502 6-1699 6-1656 5-614 6-1749 6-116 6-1518 6-1648 6-083 6-1216 6-003 6-532 6-105 6-910 6-823 6-605 6-1640 6-931 6-1449 6-627 6-1491 6-839 6-571 6-1460 6-2034 6-375 6-475 6-965 2-309

Ød Crossmm sect. d2 9.19 2.62 9.19 3.00 9.20 2.70 9.25 1.78 9.30 1.50 9.30 2.40 9.35 1.60 9.40 2.10 9.50 1.00 9.50 1.78 9.50 1.80 9.50 2.00 9.50 2.15 9.50 2.50 9.52 1.78 9.53 1.60 9.55 1.75 9.60 2.00 9.75 1.78 9.70 5.33 9.75 1.50 9.78 1.27 9.80 1.50 9.86 1.78 9.93 2.62 9.96 1.53 10.00 1.00 10.00 1.20 10.00 1.25 10.00 1.50 10.00 1.60 10.00 2.00 10.00 2.20 10.00 2.50 10.00 2.62 10.00 2.65 10.00 3.00 10.00 4.00 10.00 6.50 10.00 8.00 10.10 1.00 10.10 1.60 10.10 1.78 10.15 1.40 10.20 1.50 10.24 1.83 10.25 1.40 10.30 2.40 10.40 1.00 10.46 5.33

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

71

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – O-ring sizes acc. to inner diameter d

Sizing charts – O-ring sizes acc. to inner diameter d Parker No. 6-976 5-588 3-905 6-777 6-218 2-205 2-111 6-1505 6-551 6-1230 2-013 6-1208 6-1236 6-084 6-1516 6-1718 6-086 6-1877 6-717 6-953 6-1386 6-2071 6-1525 5-613 6-1337 6-1510 6-1376 6-1834 6-1536 6-471 6-1922 6-347 6-677 6-928 6-1575 6-1498 6-1313 6-1454 6-945 6-1873 6-2101 6-1323 6-1275 6-1468 6-1635 6-1485 6-1978 6-1856 6-366 3-906

Ød Crossmm sect. d2 10.50 1.50 10.50 2.70 10.52 1.83 10.60 1.80 10.60 2.00 10.69 3.53 10.77 2.62 10.78 2.62 10.80 1.50 10.80 1.90 10.82 1.78 10.90 1.20 11.00 1.00 11.00 1.50 11.00 1.60 11.00 1.90 11.00 2.00 11.00 2.30 11.00 2.50 11.00 3.00 11.00 3.40 11.00 3.50 11.10 1.60 11.10 1.78 11.10 1.82 11.10 2.15 11.20 1.80 11.20 2.62 11.30 2.20 11.30 2.40 11.30 4.75 11.40 2.10 11.50 1.00 11.50 1.50 11.50 1.78 11.50 1.80 11.50 2.00 11.50 2.30 11.50 2.50 11.50 3.00 11.56 1.78 11.60 1.20 11.60 2.20 11.75 1.55 11.80 1.80 11.80 2.65 11.80 3.00 11.82 2.62 11.89 1.78 11.89 1.98

Parker No. 5-615 6-438 6-1566 6-1466 6-1469 6-053 6-065 6-774 6-124 6-662 6-2100 6-1330 2-310 6-1361 5-589 2-206 6-1717 6-058 6-2069 2-112 2-014 6-550 6-1567 6-1379 6-198 6-1503 6-584 6-904 6-033 6-1484 6-1636 6-075 6-016 6-1967 6-1822 6-730 6-207 6-163 5-616 6-129 6-1198 6-1825 6-1936 6-929 6-1827 6-1202 6-348 3-907 6-1571 6-096

Ød Crossmm sect. d2 11.91 2.62 12.00 1.00 12.00 1.20 12.00 1.30 12.00 1.40 12.00 1.50 12.00 2.00 12.00 2.50 12.00 3.00 12.00 3.80 12.00 5.00 12.00 10.60 12.07 5.33 12.10 1.60 12.10 2.70 12.29 3.53 12.30 1.90 12.30 2.40 12.30 3.50 12.37 2.62 12.42 1.78 12.50 1.10 12.50 1.50 12.50 1.80 12.50 2.00 12.83 1.27 13.00 1.00 13.00 1.30 13.00 1.50 13.00 1.58 13.00 1.80 13.00 2.00 13.00 2.50 13.00 1.20 13.00 2.62 13.00 3.00 13.00 3.50 13.10 1.60 13.11 2.62 13.23 1.78 13.30 1.20 13.30 1.80 13.30 2.20 13.30 2.40 13.30 2.80 13.30 3.00 13.40 2.10 13.46 2.08 13.50 1.50 13.50 2.75

Parker No. 5-590 6-473 2-311 6-1339 6-160 2-207 6-737 2-113 6-1288 6-1049 6-1576 6-143 6-1345 2-015 6-1342 6-090 6-1555 6-067 6-705 6-2043 6-2135 6-1537 6-1923 6-1817 6-1809 6-135 6-1658 5-239 6-1813 6-397 6-1464 6-2112 6-1828 6-340 6-2070 6-1393 6-1857 6-683 6-118 6-040 6-085 6-005 6-106 6-043 6-072 6-1398 6-1099 6-128 6-1396 5-591

Ød Crossmm sect. d2 13.59 2.69 13.60 2.50 13.64 5.33 13.70 2.50 13.75 2.80 13.87 3.53 13.89 1.30 13.94 2.62 14.00 1.00 14.00 1.10 14.00 1.30 14.00 1.50 14.00 1.60 14.00 1.78 14.00 1.82 14.00 2.00 14.00 2.20 14.00 2.50 14.00 3.00 14.00 5.00 14.10 2.40 14.20 1.90 14.20 2.00 14.20 3.00 14.23 1.60 14.30 2.40 14.40 2.00 14.48 2.69 14.47 3.53 14.50 1.60 14.50 3.00 14.60 1.50 14.60 2.10 14.60 2.40 14.60 2.95 14.70 3.50 14.90 2.70 15.00 1.00 15.00 1.50 15.00 1.60 15.00 1.80 15.00 2.00 15.00 2.50 15.00 3.00 15.00 3.20 15.00 3.50 15.00 4.00 15.00 5.00 15.08 2.62 15.10 2.70

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

72

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-2094 2-312 6-1747 6-940 6-206 5-243 6-349 2-208 5-676 6-1541 6-1340 6-1770 2-114 2-016 6-1494 6-223 5-617 6-439 6-632 6-528 6-857 6-1748 6-146 6-562 6-891 6-042 6-2038 6-1021 6-1524 6-1039 3-908 6-2102 6-876 6-1579 6-1493 6-313 5-643 6-725 6-297 6-006 2-313 6-1994 5-592 6-524 6-476 6-1765 6-044 6-1700 6-946 6-974

Ød Crossmm sect. d2 15.22 1.78 15.24 5.33 15.30 1.50 15.30 2.20 15.30 2.40 15.34 2.62 15.40 2.10 15.47 3.53 15.49 1.47 15.50 1.50 15.50 2.60 15.50 4.00 15.54 2.62 15.60 1.78 15.70 2.50 15.80 2.40 15.88 2.62 16.00 1.00 16.00 1.25 16.00 1.50 16.00 1.80 16.00 1.90 16.00 2.00 16.00 2.50 16.00 2.65 16.00 3.00 16.00 3.50 16.00 4.00 16.30 1.40 16.30 2.40 16.36 2.21 16.40 1.78 16.50 1.00 16.50 1.50 16.50 2.00 16.50 2.70 16.51 1.14 16.56 1.78 16.58 1.50 16.70 1.45 16.81 5.33 16.82 5.33 16.90 2.70 17.00 1.10 17.00 1.50 17.00 1.93 17.00 2.00 17.00 2.50 17.00 3.00 17.00 3.50

Parker No. 6-1365 2-209 6-2068 2-115 2-017 6-1341 6-1109 6-1819 6-1961 5-690 6-554 6-388 6-1364 6-1610 6-1480 6-367 6-1298 6-041 5-256 6-731 6-087 6-2087 6-076 6-1040 6-132 6-425 6-007 6-2044 6-125 6-755 6-1586 6-848 6-396 6-177 5-594 5-593 2-314 6-308 6-499 6-557 2-210 2-116 2-018 6-1543 6-295 6-1276 6-573 6-798 6-360 6-039

Ød Crossmm sect. d2 17.00 4.00 17.04 3.53 17.10 1.60 17.12 2.62 17.17 1.78 17.20 1.82 17.20 3.00 17.20 4.00 17.30 2.20 17.30 2.40 17.40 2.10 17.40 2.50 17.50 4.00 17.64 2.00 17.70 1.78 17.81 1.02 17.86 2.62 17.90 1.25 17.96 2.62 18.00 1.30 18.00 1.50 18.00 1.80 18.00 2.00 18.00 2.20 18.00 2.50 18.00 3.00 18.00 3.15 18.00 3.50 18.00 4.00 18.00 5.00 18.00 10.00 18.14 1.78 18.20 3.00 18.30 2.40 18.30 3.60 18.40 2.70 18.42 5.33 18.50 1.50 18.60 2.00 18.60 3.50 18.64 3.53 18.72 2.62 18.77 1.78 18.80 1.90 19.00 0.80 19.00 1.00 19.00 1.50 19.00 1.80 19.00 2.00 19.00 2.50

Parker No. 6-779 6-998 6-404 3-910 6-593 6-1975 6-503 6-628 6-1430 6-350 6-119 6-1869 6-1463 6-1772 6-758 6-300 5-595 6-1832 2-315 6-099 6-078 6-793 6-619 6-017 6-1373 6-130 6-808 6-958 6-1091 6-1806 6-382 2-211 2-117 6-275 6-212 2-019 6-1465 6-1490 6-2055 6-1638 6-1353 6-1470 6-008 6-1311 6-089 6-1252 6-489 6-1722 6-1375 6-430

Ød Crossmm sect. d2 19.00 2.65 19.00 3.00 19.00 5.00 19.18 2.46 19.20 3.00 19.30 2.20 19.30 2.40 19.30 3.65 19.35 1.00 19.40 2.10 19.50 1.50 19.50 2.66 19.50 3.50 19.50 4.00 19.75 2.50 19.80 2.40 19.80 3.60 19.84 0.79 19.99 5.33 20.00 1.30 20.00 1.50 20.00 1.80 20.00 2.00 20.00 2.50 20.00 2.65 20.00 3.00 20.00 3.55 20.00 4.00 20.00 5.00 20.20 1.81 20.20 3.00 20.22 3.53 20.29 2.62 20.30 2.40 20.34 4.25 20.35 1.78 20.50 2.00 20.50 3.00 20.80 2.00 20.95 2.62 21.00 1.00 21.00 1.50 21.00 2.00 21.00 3.00 21.00 3.50 21.00 4.00 21.00 6.00 21.10 1.60 21.20 1.80 21.20 2.40

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

73

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – O-ring sizes acc. to inner diameter d

Sizing charts – O-ring sizes acc. to inner diameter d Parker No. 6-780 6-801 6-1818 6-1446 5-596 6-1590 6-687 6-1875 6-343 2-316 6-285 6-286 2-212 2-118 3-911 2-020 6-1731 6-1115 6-493 6-088 6-139 6-1315 6-1885 6-036 6-1083 6-877 6-2150 6-356 6-1064 6-2039 6-1086 6-2082 6-1719 6-263 6-287 6-1078 6-999 6-066 6-1911 6-1112 5-597 6-1431 2-317 6-1710 2-213 6-1930 6-1611 2-119 3-912 2-021

Ød Crossmm sect. d2 21.20 2.65 21.20 3.55 21.20 3.60 21.30 2.30 21.30 3.60 21.50 1.00 21.50 1.50 21.50 1.60 21.50 1.78 21.59 5.33 21.70 0.73 21.82 1.00 21.82 3.53 21.89 2.62 21.92 2.95 21.95 1.78 22.00 1.00 22.00 1.30 22.00 1.39 22.00 1.50 22.00 2.00 22.00 2.10 22.00 2.30 22.00 2.50 22.00 3.00 22.00 4.00 22.00 6.00 22.10 1.60 22.20 3.00 22.22 2.62 22.30 2.40 22.40 2.50 22.60 1.78 22.70 1.50 22.89 1.00 23.00 1.50 23.00 2.00 23.00 2.50 23.00 2.62 23.00 3.00 23.00 3.60 23.00 4.00 23.16 5.33 23.30 1.60 23.39 3.53 23.40 4.00 23.47 2.40 23.47 2.62 23.47 2.95 23.52 1.78

Parker No. 6-298 6-942 6-351 6-2139 6-1338 6-666 6-544 6-022 6-595 6-1027 6-453 6-443 6-050 6-288 6-1545 6-1289 6-1676 6-1768 6-1456 5-598 6-1204 2-318 6-092 2-214 6-611 6-442 6-916 6-969 6-426 6-376 3-913 2-120 2-022 6-126 6-745 6-189 6-957 6-289 6-387 5-618 6-728 6-1232 6-656 6-749 6-1082 6-2040 6-1259 5-599 2-319 6-1655

Ød Crossmm sect. d2 23.60 1.02 23.60 2.90 23.70 2.80 23.80 1.50 23.80 2.40 24.00 1.00 24.00 1.50 24.00 2.00 24.00 2.50 24.00 3.00 24.00 4.00 24.00 6.00 24.20 3.00 24.32 1.00 24.50 1.00 24.50 3.15 24.50 4.00 24.50 5.50 24.60 3.40 24.60 3.60 24.69 1.78 24.77 5.33 24.80 1.50 24.99 3.53 25.00 1.50 25.00 2.00 25.00 2.50 25.00 3.00 25.00 4.00 25.00 5.00 25.04 2.95 25.07 2.62 25.12 1.78 25.30 1.60 25.30 2.40 25.50 2.00 25.60 1.93 25.79 1.00 25.80 3.30 25.81 3.53 26.00 1.00 26.00 1.50 26.00 2.00 26.00 2.50 26.00 3.00 26.00 3.50 26.00 4.00 26.20 3.60 26.34 5.33 26.50 4.00

Parker No. 2-215 3-914 2-121 2-023 6-208 6-1613 6-400 6-049 6-894 6-1447 6-1919 6-147 6-825 6-660 6-913 6-023 6-1862 6-497 6-1540 6-2137 6-296 5-600 2-320 6-905 6-101 6-794 6-140 6-180 6-654 6-781 6-977 6-1915 6-1533 6-1031 2-216 6-1378 2-122 2-024 6-1599 6-1729 6-1698 6-1423 6-1000 6-1517 6-2148 6-2147 6-2081 5-601 6-034 2-321

Ød Crossmm sect. d2 26.57 3.53 26.59 2.95 26.64 2.62 26.70 1.78 26.70 2.50 27.00 1.40 27.00 1.50 27.00 2.00 27.00 2.50 27.00 2.70 27.00 2.80 27.00 3.00 27.00 3.20 27.00 5.00 27.20 3.00 27.30 2.40 27.50 1.00 27.50 1.50 27.50 2.00 27.60 2.40 27.71 1.02 27.80 3.60 27.94 5.33 28.00 1.00 28.00 1.50 28.00 1.80 28.00 2.00 28.00 2.20 28.00 2.50 28.00 2.65 28.00 3.00 28.00 3.50 28.00 4.00 28.00 5.00 28.17 3.53 28.20 1.00 28.24 2.62 28.30 1.78 28.30 3.10 28.68 2.40 29.00 2.00 29.00 2.50 29.00 3.00 29.10 1.60 29.20 4.95 29.20 5.00 29.20 5.05 29.30 3.60 29.50 1.50 29.51 5.33

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

74

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-352 3-916 2-217 2-123 2-025 6-1627 6-048 6-1203 6-1474 6-156 6-056 6-037 6-1906 6-803 6-454 6-663 6-1366 6-290 6-142 5-602 6-1478 6-1401 6-324 6-1578 6-097 6-314 2-322 2-218 2-124 2-026 6-1146 6-1769 6-1461 6-766 6-760 6-1556 6-2130 6-869 6-850 6-646 6-1332 6-1920 6-838 6-1634 6-784 5-603 2-323 2-219 2-125 6-1780

Ød Crossmm sect. d2 29.70 2.80 29.74 2.95 29.74 3.53 29.82 2.62 29.87 1.78 30.00 1.00 30.00 2.00 30.00 2.15 30.00 2.25 30.00 2.50 30.00 3.00 30.00 3.15 30.00 3.50 30.00 3.55 30.00 4.00 30.00 4.65 30.00 5.00 30.30 2.40 30.70 2.00 30.80 3.60 31.00 1.50 31.00 2.00 31.00 2.50 31.00 4.00 31.00 4.50 31.02 3.00 31.12 5.33 31.34 3.53 31.42 2.62 31.47 1.78 31.50 3.15 31.50 7.00 31.57 1.98 31.70 3.50 31.95 2.60 32.00 1.50 32.00 1.78 32.00 2.00 32.00 2.50 32.00 2.70 32.00 3.00 32.00 3.50 32.00 4.00 32.50 3.00 32.50 3.55 32.50 3.60 32.69 5.33 32.92 3.53 32.99 2.62 33.00 1.50

Parker No. 6-136 6-540 6-1138 6-1411 6-1614 2-027 6-472 6-802 5-157 6-1047 6-1890 6-2105 6-1197 6-1631 6-622 6-914 6-1839 5-604 2-324 6-1150 6-585 3-918 6-2047 2-220 2-126 2-028 6-752 6-1100 6-047 6-606 6-1116 6-993 6-1926 6-1166 6-545 6-1414 6-377 6-1124 6-1600 6-1650 5-605 6-1808 6-1805 6-980 6-2133 6-678 6-694 6-609 6-329 6-1140

Ød Crossmm sect. d2 33.00 2.00 33.00 2.50 33.00 3.00 33.00 3.50 33.00 5.00 33.05 1.78 33.30 2.40 33.50 2.65 33.99 2.34 34.00 1.00 34.00 1.10 34.00 1.50 34.00 2.00 34.00 2.50 34.00 2.80 34.00 3.00 34.00 4.00 34.10 3.60 34.29 5.33 34.40 2.10 34.40 3.10 34.42 2.95 34.50 2.65 34.52 3.53 34.59 2.62 34.65 1.78 34.65 2.60 35.00 1.50 35.00 2.00 35.00 2.50 35.00 3.00 35.00 3.20 35.00 3.50 35.00 4.00 35.00 4.50 35.00 5.00 35.00 5.30 35.15 3.15 35.40 3.25 35.50 4.00 35.60 3.60 35.95 1.78 35.96 2.32 36.00 1.50 36.00 1.78 36.00 2.00 36.00 2.10 36.00 2.20 36.00 2.50 36.00 3.00

Parker No. 6-1980 6-1652 2-221 2-127 6-1087 6-154 5-670 6-2054 6-970 6-1188 6-291 6-881 6-555 5-606 6-459 3-920 2-325 6-1711 6-1257 2-222 2-128 2-029 6-1589 6-1389 6-046 6-433 6-1092 6-1025 6-2020 6-221 6-782 6-353 6-575 6-1547 6-1038 6-1482 6-205 6-1362 2-129 6-1148 6-586 6-753 5-321 6-642 6-027 6-566 6-292 6-1912 6-1497 6-1023

Ød Crossmm sect. d2 36.00 4.00 36.00 5.00 36.09 3.53 36.17 2.62 36.20 3.00 36.30 1.78 36.50 1.78 36.60 2.90 37.00 1.50 37.00 2.00 37.00 2.50 37.00 3.00 37.00 5.00 37.30 3.60 37.36 2.60 37.47 3.00 37.47 5.33 37.50 1.80 37.50 4.00 37.69 3.53 37.77 2.62 37.82 1.78 38.00 1.00 38.00 1.50 38.00 2.00 38.00 2.50 38.00 3.00 38.00 3.50 38.00 4.00 38.00 5.00 38.70 2.65 38.70 2.80 39.00 2.00 39.00 2.50 39.00 3.00 39.00 5.00 39.20 3.00 39.20 5.70 39.34 2.62 39.40 2.10 39.40 3.10 39.50 2.60 39.60 3.53 40.00 1.50 40.00 2.00 40.00 2.50 40.00 3.00 40.00 3.50 40.00 4.00 40.00 5.00

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

75

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – O-ring sizes acc. to inner diameter d

Sizing charts – O-ring sizes acc. to inner diameter d Parker No. 6-1114 6-102 2-326 6-972 2-223 2-130 6-1144 2-030 6-541 6-449 6-525 6-337 6-2083 6-875 6-414 6-1486 6-015 6-2088 6-594 6-227 6-1319 6-1399 6-1224 6-1601 6-845 6-2119 2-131 5-330 5-332 6-1189 6-996 6-1903 6-1060 6-2018 6-1413 6-759 6-809 6-1723 2-327 6-431 6-1054 2-224 2-132 2-031 6-542 6-1349 6-1520 6-193 6-772 6-975

Ød Crossmm sect. d2 40.00 6.00 40.60 4.00 40.64 5.33 40.82 2.59 40.87 3.53 40.94 2.62 41.00 1.50 41.00 1.78 41.00 2.50 41.00 3.00 41.28 3.53 41.40 2.62 41.50 2.00 41.60 2.40 41.75 2.60 42.00 1.00 42.00 1.50 42.00 2.00 42.00 2.50 42.00 3.00 42.00 4.00 42.00 4.50 42.00 5.00 42.40 4.25 42.50 1.80 42.50 3.53 42.52 2.62 42.52 5.33 42.85 3.53 43.00 2.00 43.00 3.00 43.00 3.50 43.00 4.00 43.00 5.00 43.00 5.50 43.25 2.60 43.70 1.80 43.70 3.55 43.82 5.33 44.00 2.00 44.00 3.00 44.04 3.53 44.12 2.62 44.17 1.78 44.20 2.50 44.30 5.70 44.35 2.58 44.35 3.00 44.70 3.50 44.83 2.67

Parker No. 6-1724 6-882 6-082 6-054 6-323 6-783 6-997 6-1907 6-1178 6-1195 6-726 6-1897 6-2008 5-035 6-2090 2-133 6-750 6-1176 6-1020 6-944 6-1248 6-159 6-354 6-423 2-328 6-1141 6-1041 6-1633 6-1059 6-1913 6-1483 6-293 2-225 2-134 2-032 6-009 6-1854 6-370 6-2074 6-2052 6-155 6-1196 6-673 6-1343 6-435 2-135 6-1253 6-912 5-701 6-1070

Ød Crossmm sect. d2 44.96 2.57 45.00 1.00 45.00 1.50 45.00 2.00 45.00 2.50 45.00 2.65 45.00 3.00 45.00 3.50 45.00 4.00 45.00 4.50 45.00 5.00 45.00 6.00 45.30 1.93 45.36 3.53 45.69 1.78 45.69 2.62 45.90 1.50 46.00 2.00 46.00 3.00 46.00 4.00 46.00 5.00 46.02 3.53 46.70 2.80 46.87 2.62 46.99 5.33 47.00 2.00 47.00 2.50 47.00 3.00 47.00 4.00 47.00 5.00 47.00 5.50 47.20 5.70 47.22 3.53 47.29 2.62 47.35 1.78 47.50 4.00 48.00 1.00 48.00 2.00 48.00 2.10 48.00 2.30 48.00 3.00 48.00 4.00 48.20 1.78 48.20 3.00 48.40 4.85 48.90 2.62 49.00 2.00 49.20 3.00 49.20 3.53 49.20 5.70

Parker No. 6-194 6-1931 6-2113 6-1981 6-051 6-055 6-964 6-1437 6-603 6-791 6-1226 2-329 6-1489 6-1684 2-226 2-136 2-033 6-630 6-1721 6-434 5-037 6-1333 6-1587 6-1234 6-556 2-137 6-893 6-1991 6-1185 6-1347 6-1024 6-2143 6-1914 6-113 6-112 3-928 2-330 6-1657 2-227 2-138 2-034 6-1317 6-1513 6-1274 6-819 6-1643 6-879 6-2117 6-1602 6-810

Ød Crossmm sect. d2 49.50 3.00 49.50 5.00 49.88 1.78 50.00 1.50 50.00 2.00 50.00 2.50 50.00 3.00 50.00 3.50 50.00 4.00 50.00 4.50 50.00 5.00 50.17 5.33 50.20 3.00 50.30 2.50 50.39 3.53 50.47 2.62 50.52 1.78 51.00 3.00 51.10 1.60 51.50 1.50 51.71 3.53 51.94 3.53 52.00 1.00 52.00 2.50 52.00 3.00 52.07 2.62 52.20 5.70 52.39 3.53 52.50 1.80 53.00 2.00 53.00 3.50 53.00 3.55 53.00 4.00 53.00 5.00 53.00 6.50 53.09 3.00 53.34 5.33 53.50 2.00 53.57 3.53 53.64 2.62 53.70 1.78 53.80 4.00 54.00 1.50 54.00 2.00 54.00 3.00 54.00 3.15 54.00 4.00 54.00 4.5 54.40 4.25 54.50 2.65

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

76

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-1438 6-1695 6-141 6-1709 6-1065 6-1192 6-1186 6-1448 2-139 6-703 6-568 6-985 6-785 6-1145 6-739 6-1703 2-331 6-1271 2-228 2-140 2-035 6-643 6-719 6-427 6-1137 6-447 6-1985 6-1354 6-2019 6-1666 6-109 2-141 5-702 6-1585 3-932 6-1864 6-764 2-332 6-560 2-229 2-142 6-883 6-1726 6-411 6-665 6-107 6-1368 6-114 2-036 6-2118

Ød Crossmm sect. d2 54.70 3.53 55.00 1.20 55.00 2.00 55.00 2.50 55.00 3.00 55.00 3.50 55.00 4.00 55.00 5.00 55.25 2.62 55.30 2.00 56.00 2.00 56.00 3.00 56.00 3.55 56.00 4.00 56.00 4.50 56.50 5.30 56.52 5.33 56.70 3.00 56.74 3.53 56.82 2.62 56.87 1.78 57.00 1.50 57.00 2.50 57.00 3.00 57.00 4.00 58.00 2.00 58.00 2.50 58.00 3.00 58.00 3.55 58.00 3.75 58.00 4.00 58.42 2.62 58.74 3.53 59.20 5.70 59.36 3.00 59.50 5.00 59.60 5.85 59.69 5.33 59.70 7.00 59.92 3.53 59.99 2.62 60.00 1.20 60.00 2.00 60.00 2.50 60.00 3.00 60.00 4.10 60.00 4.50 60.00 5.00 60.05 1.78 60.40 3.00

Parker No. 6-851 6-1034 6-633 6-792 2-143 6-1439 6-1419 6-455 6-699 6-1209 6-1261 6-1117 2-333 6-242 6-2045 6-1162 6-151 6-474 6-1094 2-230 6-2132 2-144 2-037 6-636 6-1661 6-1123 5-805 2-145 6-1588 6-1372 6-501 6-1377 6-523 6-1053 6-596 6-1037 6-416 6-1927 5-703 6-1974 6-500 6-1193 6-1273 2-334 2-231 2-146 2-038 6-243 6-316 6-1876

Ød Crossmm sect. d2 61.00 2.00 61.00 4.00 61.00 4.50 61.00 5.00 61.60 2.62 61.70 4.50 62.00 1.50 62.00 2.50 62.00 3.00 62.00 3.53 62.00 4.00 62.00 6.00 62.87 5.33 63.00 2.50 63.00 3.00 63.00 3.50 63.00 4.00 63.00 4.50 63.00 6.00 63.09 3.53 63.10 3.53 63.17 2.62 63.22 1.78 64.00 3.00 64.00 4.00 64.20 5.70 64.39 1.78 64.77 2.62 65.00 1.00 65.00 1.80 65.00 2.00 65.00 2.65 65.00 3.00 65.00 4.00 65.00 4.50 65.00 5.00 65.00 5.30 65.00 5.50 65.09 3.53 66.00 1.50 66.00 2.00 66.00 3.00 66.00 5.00 66.04 5.33 66.27 3.53 66.34 2.62 66.40 1.78 67.00 1.50 67.00 2.50 67.00 2.80

Parker No. 6-659 6-786 6-1607 6-1797 5-361 2-147 6-2079 6-884 6-1380 6-1272 6-941 6-1908 6-990 6-824 6-1966 6-1704 2-335 6-272 2-232 2-148 2-039 6-2120 6-0641 6-552 6-1462 6-031 6-1778 6-1194 6-539 6-899 6-1917 6-2077 6-1212 6-1740 6-787 6-634 2-149 5-704 6-979 6-045 6-1013 6-1909 2-336 2-233 2-150 2-040 6-1628 6-030 6-757 6-1348

Ød Crossmm sect. d2 67.00 3.00 67.00 3.55 67.00 4.00 67.39 2.26 67.84 3.53 67.95 2.62 68.00 2.50 68.00 3.00 68.00 3.50 68.00 4.00 68.00 5.00 68.00 5.50 69.00 2.50 69.00 3.00 69.00 4.50 69.20 5.30 69.22 5.33 69.24 3.40 69.44 3.53 69.52 2.62 69.57 1.78 69.60 5.00 70.00 1.50 70.00 2.00 70.00 2.50 70.00 3.00 70.00 3.50 70.00 4.00 70.00 4.50 70.00 5.00 70.00 5.50 70.00 7.00 70.00 8.00 70.50 3.20 71.00 3.55 71.00 4.50 71.12 2.62 71.44 3.53 72.00 2.50 72.00 3.00 72.00 4.00 72.00 5.50 72.39 5.33 72.62 3.53 72.69 2.62 72.75 1.78 73.00 2.00 73.00 3.00 73.00 4.00 73.00 7.00

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

77

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – O-ring sizes acc. to inner diameter d

Sizing charts – O-ring sizes acc. to inner diameter d Parker No. 6-178 6-2012 6-483 6-2104 6-294 6-587 6-1771 6-2075 6-1609 5-705 6-1889 6-2096 6-1357 6-1075 6-1001 6-1916 6-1928 2-337 2-234 2-151 2-041 6-1369 6-754 6-921 6-464 6-805 6-1417 6-1069 6-1662 6-1467 6-1950 6-2033 6-1475 6-978 6-729 6-826 6-1002 2-338 2-235 6-820 6-1152 6-992 6-1675 6-195 6-108 6-790 6-569 6-1270 6-1316 6-788

Ød Crossmm sect. d2 74.00 2.00 74.00 2.50 74.00 3.00 74.00 4.50 74.20 5.70 74.40 3.10 74.50 3.00 74.50 4.00 74.60 3.53 74.61 3.53 74.90 1.78 74.90 2.00 75.00 2.50 75.00 3.00 75.00 4.00 75.00 4.50 75.00 5.50 75.57 5.33 75.79 3.53 75.87 2.62 75.92 1.78 76.00 2.00 76.00 2.50 76.00 3.00 76.00 4.50 77.00 2.00 77.00 2.50 77.10 2.62 77.50 2.00 77.50 2.62 77.80 1.50 78.00 1.50 78.00 2.00 78.00 2.50 78.00 3.00 78.00 3.50 78.00 5.00 78.74 5.33 78.97 3.53 79.00 1.50 79.20 5.70 79.30 2.62 79.50 2.65 79.50 3.00 79.60 3.20 80.00 1.80 80.00 2.00 80.00 3.00 80.00 3.50 80.00 3.55

Parker No. 6-1057 6-1181 5-816 6-885 6-121 6-1077 2-339 6-513 6-1472 6-445 2-236 2-152 2-042 6-821 6-900 6-1715 6-1804 6-184 6-676 6-456 6-1134 6-1012 6-588 6-2122 6-822 6-733 6-1014 6-853 6-1445 6-1174 6-1406 2-340 6-452 2-237 6-991 6-1776 6-1457 6-1573 6-574 6-579 6-558 6-1016 6-309 6-1779 6-276 6-1052 6-1629 6-1165 6-1111 2-341

Ød Crossmm sect. d2 80.00 4.00 80.00 5.00 80.31 1.78 80.50 4.00 81.00 3.00 81.00 4.00 81.92 5.33 82.00 2.00 82.00 3.00 82.00 4.00 82.14 3.53 82.22 2.62 82.27 1.78 83.00 1.00 83.00 3.00 83.00 4.00 83.77 1.78 83.80 2.62 84.00 2.50 84.00 3.00 84.00 3.50 84.30 5.70 84.40 3.10 84.50 3.00 85.00 1.50 85.00 2.00 85.00 3.00 85.00 4.00 85.00 5.00 85.00 6.00 85.00 6.99 85.09 5.33 85.20 9.25 85.32 3.53 86.00 2.62 86.00 3.20 86.00 4.00 86.50 4.00 86.84 5.33 87.00 3.00 87.20 2.50 87.20 5.70 87.30 2.00 87.60 3.00 88.00 3.00 88.00 4.00 88.00 5.00 88.00 6.00 88.00 8.00 88.27 5.33

Parker No. 5-381 6-561 6-1705 2-238 6-1508 2-153 2-043 6-2030 6-2108 6-867 6-013 6-1782 6-498 6-1113 6-216 6-1179 6-1265 6-1214 6-1904 6-1103 6-1777 6-1429 6-100 2-342 2-239 6-1452 6-1061 6-1507 6-804 6-720 6-743 6-963 6-1056 6-257 6-1672 6-405 6-446 6-1095 6-1029 6-1665 6-608 6-339 2-343 2-240 2-154 2-044 6-1781 6-1673 6-863 6-1062

Ød Crossmm sect. d2 88.27 6.99 88.30 7.00 88.40 5.30 88.49 3.53 88.50 6.50 88.57 2.62 88.62 1.78 89.00 1.50 89.00 1.90 89.20 5.70 89.50 3.00 90.00 1.50 90.00 2.00 90.00 2.50 90.00 3.00 90.00 4.00 90.00 4.80 90.00 5.00 90.00 5.50 90.00 7.00 90.80 3.50 91.00 2.00 91.00 3.00 91.44 5.33 91.67 3.53 92.00 3.00 92.00 4.00 92.20 2.62 92.50 3.55 93.00 2.00 93.00 3.00 93.00 4.00 93.00 5.00 93.39 1.47 93.40 2.57 93.50 9.50 94.00 2.00 94.00 3.00 94.00 4.00 94.00 5.70 94.20 5.70 94.50 3.00 94.62 5.33 94.84 3.53 94.92 2.62 94.97 1.78 95.00 1.50 95.00 3.00 95.00 4.00 95.00 4.50

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

78

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-874 6-1910 6-582 6-700 6-832 6-640 6-1415 6-1306 2-344 6-1708 6-157 2-241 6-1303 6-392 6-1089 6-601 6-174 6-1305 6-413 6-137 6-1905 6-1395 6-1237 2-345 6-025 2-242 2-155 2-045 6-724 6-1163 6-1055 6-2121 6-1200 2-346 6-1720 6-1350 2-243 6-1175 6-589 6-1381 6-806 6-995 6-1074 6-094 6-253 6-1320 6-762 2-347 2-244 2-156

Ød Crossmm sect. d2 95.00 5.00 95.00 5.50 95.50 3.53 96.00 2.00 96.00 9.00 97.00 1.50 97.00 4.00 97.00 5.00 97.79 5.33 98.00 2.50 98.00 3.00 98.02 3.53 99.00 3.00 99.00 6.99 99.20 5.70 100.00 2.00 100.00 2.50 100.00 3.00 100.00 4.00 100.00 5.00 100.00 5.50 100.00 6.00 100.00 8.00 100.97 5.33 101.00 3.00 101.19 3.53 101.27 2.62 101.32 1.78 102.00 3.00 102.00 4.00 103.00 5.00 104.00 5.00 104.00 5.30 104.14 5.33 104.20 5.70 104.30 5.70 104.37 3.53 104.50 3.00 105.00 2.00 105.00 3.00 105.00 3.50 105.00 4.00 105.00 5.00 106.00 3.00 106.80 2.66 107.00 8.00 107.31 6.99 107.32 5.33 107.54 3.53 107.62 2.62

Parker No. 2-046 6-1106 6-740 6-837 6-815 6-767 6-2036 6-1580 6-1367 6-903 6-1644 6-915 6-1671 2-348 2-245 6-1651 6-421 6-873 6-1182 2-349 2-425 2-246 2-157 6-982 6-1164 2-047 6-1005 6-769 6-1826 6-1151 6-274 6-1169 6-1660 6-1421 6-1322 6-1105 2-350 2-426 2-247 6-032 6-580 6-123 5-843 6-448 6-768 6-674 6-504 6-1076 6-1180 6-1003

Ød Crossmm sect. d2 107.67 1.78 108.00 8.00 109.00 3.00 109.20 5.70 109.20 5.84 109.40 3.10 109.50 5.33 110.00 1.50 110.00 2.50 110.00 3.00 110.00 3.50 110.00 5.00 110.00 6.00 110.49 5.33 110.72 3.53 112.00 2.50 112.00 3.00 112.00 4.00 112.00 7.00 113.67 5.33 113.67 6.99 113.89 3.53 113.97 2.62 114.00 3.00 114.00 5.00 114.02 1.78 114.20 5.70 114.40 3.10 114.55 2.57 115.00 2.00 115.00 3.00 115.00 5.00 115.00 5.33 115.00 6.00 116.00 3.00 116.50 1.78 116.84 5.33 116.84 6.99 117.07 3.53 118.00 2.00 118.31 3.53 118.50 3.00 118.72 2.62 119.20 5.70 119.60 5.70 120.00 1.50 120.00 3.00 120.00 4.00 120.00 5.00 120.00 6.00

Parker No. 6-1427 2-351 2-427 2-248 2-158 2-048 6-2064 6-961 6-1630 6-2107 2-352 2-428 2-249 6-1143 6-1281 6-612 6-1990 6-1199 6-115 5-850 6-255 6-1942 2-353 2-429 2-250 2-159 2-049 6-722 6-1473 6-1962 6-1073 6-1591 6-1096 6-451 2-354 2-430 2-251 6-693 6-1296 6-1084 6-902 6-2046 6-577 6-1436 6-1775 6-1217 6-095 6-1015 2-355 2-431

Ød Crossmm sect. d2 120.00 10.00 120.02 5.33 120.02 6.99 120.24 3.53 120.32 2.62 120.37 1.78 121.00 8.00 122.00 3.00 122.00 6.00 123.00 3.00 123.19 5.33 123.19 6.99 123.42 3.53 124.00 4.00 125.00 2.50 125.00 3.00 125.00 3.50 125.00 4.00 125.00 8.00 125.09 6.60 126.00 5.00 126.30 5.33 126.37 5.33 126.37 6.99 126.59 3.53 126.67 2.62 126.72 1.78 128.00 2.00 128.00 3.00 128.00 4.00 128.00 5.00 129.00 1.50 129.00 4.00 129.20 5.70 129.54 5.33 129.54 6.99 129.77 3.53 130.00 2.50 130.00 3.00 130.00 4.00 130.00 5.00 130.00 5.80 130.00 6.00 131.00 5.30 131.10 3.20 131.50 4.00 132.00 3.00 132.00 4.00 132.72 5.33 132.72 6.99

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

79

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – O-ring sizes acc. to inner diameter d

Sizing charts – O-ring sizes acc. to inner diameter d Parker No. 2-252 6-1933 2-160 2-050 6-688 6-812 6-515 6-1329 6-1783 6-1277 6-059 6-060 6-844 6-1085 6-2000 2-356 2-432 6-1559 6-1154 2-253 6-1807 6-026 6-833 6-559 6-341 6-1949 6-379 6-224 2-357 2-433 2-254 2-161 6-698 6-511 6-1136 6-602 6-1051 6-1093 6-1207 2-358 2-434 2-255 6-1592 6-2149 6-512 6-1632 6-1696 6-1233 6-1046 2-359

Ød Crossmm sect. d2 132.94 3.53 133.00 3.00 133.02 2.62 133.07 1.78 133.35 5.33 133.50 12.00 134.00 3.00 134.00 8.00 135.00 1.50 135.00 3.00 135.00 3.23 135.00 3.43 135.00 4.00 135.00 5.00 135.50 6.00 135.89 5.33 135.89 6.99 136.00 3.00 136.00 4.00 136.12 3.53 136.53 1.78 137.00 3.00 137.00 4.00 137.00 14.00 137.30 8.00 137.50 3.30 138.00 2.10 138.00 6.00 139.07 5.33 139.07 6.99 139.29 3.53 139.37 2.62 140.00 2.00 140.00 3.00 140.00 5.00 140.00 10.00 142.00 4.00 142.00 6.00 142.00 12.00 142.24 5.33 142.24 6.99 142.47 3.53 142.90 3.20 143.00 1.45 144.00 3.70 145.00 2.50 145.00 2.88 145.00 4.00 145.00 5.00 145.42 5.33

Parker No. 2-435 2-256 2-162 6-061 6-1680 6-2021 6-756 2-257 2-360 2-436 6-1774 6-623 6-932 6-2022 6-689 6-872 6-1295 6-2129 6-222 6-1147 6-496 6-1803 6-318 2-361 2-437 2-258 6-1107 2-163 6-1594 6-1773 6-1625 6-1294 6-1390 6-1318 6-1324 6-773 6-1605 2-362 2-438 2-259 2-164 6-170 6-444 6-576 6-818 6-1081 6-1702 6-1292 6-103 6-1045

Ød Crossmm sect. d2 145.42 6.99 145.64 3.53 145.72 2.62 146.00 3.23 147.60 2.65 148.00 2.50 148.00 10.00 148.52 3.53 148.59 5.33 148.59 6.99 148.60 3.20 149.20 5.70 150.00 2.00 150.00 2.50 150.00 3.00 150.00 4.00 150.00 5.00 150.00 5.30 150.00 5.40 150.00 6.00 151.00 3.00 151.39 2.57 151.70 5.60 151.77 5.33 151.77 6.99 151.99 3.53 152.00 8.00 152.07 2.62 152.40 3.20 153.50 3.20 154.60 1.78 155.00 3.00 155.00 3.53 155.00 4.00 155.00 5.00 155.00 10.00 156.00 4.00 158.12 5.33 158.12 6.99 158.34 3.53 158.42 2.62 159.00 4.00 159.20 5.70 160.00 3.00 160.00 4.00 160.00 5.00 160.00 5.30 160.00 6.00 161.00 3.00 162.00 2.50

Parker No. 6-494 6-1815 6-1612 6-983 6-814 6-1865 2-363 2-439 2-260 2-165 6-911 6-1402 6-1529 6-1593 6-2125 6-1336 6-1929 6-746 6-2131 6-1097 6-1290 2-364 2-440 6-282 2-261 2-166 6-1659 6-887 6-1177 6-1004 6-492 6-655 6-889 6-1356 6-1068 6-841 6-148 2-365 2-441 2-262 2-167 6-631 6-1098 6-704 6-1088 6-1280 6-1706 6-1110 6-1119 6-862

Ød Crossmm sect. d2 162.50 3.53 163.07 1.63 164.00 2.00 164.20 5.70 164.20 5.84 164.33 2.62 164.47 5.33 164.47 6.99 164.69 3.53 164.77 2.62 165.00 2.00 165.00 4.00 165.00 5.00 165.10 3.20 165.30 1.78 167.50 3.50 168.40 6.00 169.20 5.70 169.98 3.56 170.00 4.00 170.00 5.00 170.82 5.33 170.82 6.99 171.00 11.00 171.04 3.53 171.12 2.62 171.45 3.20 172.00 3.00 172.00 4.00 172.00 6.00 174.00 3.00 174.20 5.70 174.30 3.50 175.00 5.00 175.00 6.00 175.00 10.00 177.00 2.00 177.17 5.33 177.17 6.99 177.39 3.53 177.47 2.62 179.00 3.00 179.20 5.70 180.00 3.00 180.00 4.00 180.00 5.00 180.00 5.30 180.00 6.00 180.00 8.00 180.00 10.00

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

80

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-1108 5-434 6-1816 2-366 2-442 2-263 2-168 6-1058 6-1428 6-1028 6-1121 6-122 6-1007 6-466 6-2084 6-706 2-367 2-443 6-1848 6-495 6-1044 6-614 2-264 2-169 6-299 6-1260 6-1391 6-1238 6-2098 6-868 6-1283 6-1453 6-920 6-273 2-368 2-444 2-265 2-170 6-547 6-1932 6-1450 6-1563 6-1307 6-1139 6-226 6-865 2-369 2-445 2-266 2-171

Ød Crossmm sect. d2 180.52 5.33 180.54 6.99 183.00 1.78 183.52 5.33 183.52 6.99 183.74 3.53 183.82 2.62 185.00 3.00 185.00 4.00 185.00 5.00 185.00 6.00 186.44 6.99 187.10 8.40 188.00 4.00 188.14 1.78 189.20 5.70 189.87 5.33 189.87 6.99 190.00 1.78 190.00 3.00 190.00 4.00 190.00 5.00 190.09 3.53 190.17 2.62 191.00 1.78 192.00 4.00 192.00 8.00 194.00 14.00 193.70 7.00 195.00 3.50 195.00 5.00 195.00 6.00 195.50 12.00 196.00 12.00 196.22 5.33 196.22 6.99 196.44 3.53 196.52 2.62 197.00 3.00 197.00 6.00 198.00 4.00 198.00 8.00 200.00 4.00 200.00 5.00 200.00 6.00 201.00 4.00 202.57 5.33 202.57 6.99 202.79 3.53 202.87 2.62

Parker No. 6-342 6-1849 6-149 6-546 6-1565 6-1866 6-1153 6-1725 2-370 2-267 6-600 2-172 6-0629 6-1118 6-152 5-445 6-2051 6-461 6-954 6-1867 6-570 2-371 2-446 2-268 2-173 6-1302 6-1048 6-1050 6-254 6-183 6-502 6-1063 6-1425 6-1560 2-372 2-269 2-174 6-1225 6-1679 6-949 6-1654 6-1945 6-1250 6-485 6-1896 6-150 2-373 2-447 6-1211 2-270

Ød Crossmm sect. d2 204.00 8.00 205.00 1.78 205.00 2.00 205.00 3.00 205.00 5.00 206.00 5.70 206.00 7.00 208.00 4.00 208.92 5.33 209.14 3.53 209.20 5.70 209.22 2.62 210.00 3.00 210.00 4.00 210.00 5.00 210.24 6.99 212.00 5.30 213.68 7.14 214.63 2.18 215.00 5.00 215.00 6.00 215.27 5.33 215.27 6.99 215.49 3.53 215.57 2.62 216.00 4.00 218.00 5.80 218.00 6.00 218.00 12.00 219.00 5.30 220.00 3.00 220.00 5.00 220.00 7.00 221.00 1.78 221.62 5.33 221.84 3.53 221.92 2.62 222.00 7.00 223.00 2.65 223.00 5.33 224.00 6.00 224.00 7.00 225.00 3.00 225.00 5.00 226.20 3.53 227.00 2.00 227.97 5.33 227.97 6.99 228.00 3.00 228.19 3.53

Parker No. 2-175 6-516 6-1727 6-1767 6-1948 6-1293 6-252 6-918 6-846 6-618 2-374 2-271 2-176 6-1451 6-2145 6-1360 6-635 6-412 6-1426 6-1282 6-1239 6-1895 6-604 6-1346 6-1564 6-436 6-1384 2-375 2-448 2-272 2-177 6-281 6-407 6-878 6-1861 6-1155 6-1534 6-671 6-967 6-1668 6-1263 2-376 2-273 2-178 6-1030 6-1167 6-1010 6-514 6-1993 6-1132

Ød Crossmm sect. d2 228.27 2.62 230.00 3.00 230.00 4.50 230.00 4.80 230.00 5.00 230.00 8.00 231.50 6.00 234.10 8.40 234.20 7.00 234.32 1.78 234.34 5.33 234.54 3.53 234.62 2.62 235.00 4.00 235.00 6.00 236.00 6.00 236.00 7.00 238.00 5.00 238.00 6.00 238.00 10.00 238.00 14.00 239.20 3.53 240.00 3.00 240.00 5.00 240.00 8.00 240.00 12.00 240.66 7.40 240.67 5.33 240.67 6.99 240.89 3.53 240.97 2.62 241.00 7.00 242.00 6.00 245.00 3.00 245.00 3.53 245.00 5.00 245.00 7.00 245.00 10.00 245.00 10.85 246.00 3.00 246.00 4.00 247.02 5.33 247.24 3.53 247.32 2.62 248.00 5.00 248.00 7.00 249.30 5.70 250.00 3.00 250.00 4.00 250.00 8.00

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

81

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – O-ring sizes acc. to inner diameter d

Sizing charts – O-ring sizes acc. to inner diameter d Parker No. 6-1582 6-1227 2-377 2-449 2-274 6-842 6-1522 6-1388 6-896 6-718 6-1860 6-1231 6-871 6-2146 6-1201 6-1042 6-336 5-976 6-1403 6-1190 2-378 2-450 2-275 6-505 6-988 6-1868 6-1331 6-936 6-175 6-1279 6-948 6-1476 6-2005 2-379 2-451 6-1667 2-276 6-638 6-840 6-234 6-1477 6-2114 6-238 6-1240 6-1018 6-1191 6-241 2-380 2-452 2-277

Ød Crossmm sect. d2 250.00 10.00 252.00 4.00 253.37 5.33 253.37 6.99 253.59 3.53 255.00 4.00 255.00 5.00 256.00 4.00 257.20 14.00 258.40 1.60 259.20 3.53 260.00 4.00 260.00 5.00 260.00 6.00 260.00 8.00 261.00 6.00 262.00 5.33 264.79 6.60 265.00 5.00 266.00 4.00 266.07 5.33 266.07 6.99 266.29 3.53 270.00 3.00 270.00 5.33 270.00 6.00 272.00 8.00 272.64 3.53 273.05 3.53 273.60 5.00 274.00 5.33 275.00 5.00 276.00 2.62 278.77 5.33 278.77 6.99 278.99 2.62 278.99 3.53 281.00 5.00 282.37 3.53 283.00 12.00 285.00 5.00 285.00 6.00 285.00 12.00 285.00 14.10 289.42 5.87 290.00 5.00 291.00 6.00 291.47 5.33 291.47 6.99 291.69 3.53

Parker No. 6-1663 6-2140 6-917 6-1424 6-2037 6-854 6-1278 6-2134 6-2080 6-1168 6-1370 6-1310 2-381 2-453 2-278 6-553 6-1359 6-935 6-1351 6-1371 6-2111 6-1125 6-2109 6-1880 6-607 6-1171 6-510 5-488 2-454 6-1210 6-1707 6-716 6-1458 6-153 6-1172 6-1404 6-947 6-1546 6-1126 6-1784 2-382 2-455 2-279 6-1258 6-283 6-469 6-1408 6-1947 6-517 6-2013

Ød Crossmm sect. d2 294.00 3.00 295.00 6.00 296.00 6.00 297.00 4.00 297.80 6.99 298.00 2.62 299.50 5.00 300.00 4.00 300.00 5.00 300.00 6.00 300.00 8.00 300.00 10.00 304.17 5.33 304.17 6.99 304.39 3.53 304.80 1.78 304.80 3.18 307.57 3.53 309.30 5.70 310.00 5.00 310.00 2.62 311.00 10.00 312.90 1.78 313.00 5.33 315.00 4.00 315.00 5.00 315.00 6.00 316.56 2.62 316.87 6.99 320.00 3.00 320.00 3.53 320.00 6.00 320.00 6.50 320.00 5.33 320.62 3.53 325.00 5.00 325.00 5.33 328.00 6.99 329.00 10.00 329.57 4.80 329.57 5.33 329.57 6.99 329.79 3.53 330.00 5.00 330.00 6.00 330.00 8.00 331.50 6.00 334.00 2.62 335.00 3.00 335.00 5.00

Parker No. 6-1129 6-1235 6-1090 6-1043 6-1218 6-1881 6-1334 6-813 2-456 6-1255 6-1135 6-1918 6-1583 6-1639 6-1392 2-383 2-457 6-518 6-1888 2-280 6-895 6-1795 6-1142 6-1101 6-1836 6-1205 6-672 6-1786 6-203 2-458 6-1842 6-1254 6-807 6-1958 6-598 6-682 6-723 6-897 6-927 2-384 2-459 2-281 6-204 6-1328 6-1241 6-711 6-1387 2-460 6-1374 6-209

Ød Crossmm sect. d2 335.00 7.00 336.00 5.33 336.00 7.00 338.00 6.00 340.00 4.00 340.00 5.33 340.00 10.00 341.00 14.00 342.27 6.99 343.00 6.00 345.00 5.00 349.00 5.33 350.00 10.00 351.21 4.00 354.96 6.09 354.97 5.33 354.97 6.99 355.00 3.00 355.00 8.00 355.19 3.53 359.20 13.80 359.53 5.33 360.00 4.00 360.00 7.50 362.00 4.00 362.00 5.00 364.00 10.00 365.00 5.30 367.00 3.50 367.67 6.99 367.89 2.66 368.00 6.00 370.00 5.50 372.00 4.00 375.00 5.34 375.00 10.00 380.00 4.00 380.00 6.00 380.00 8.00 380.37 5.33 380.37 6.99 380.59 3.53 381.00 5.00 383.60 5.00 385.00 14.20 388.00 5.00 390.00 4.00 393.07 6.99 395.00 12.00 398.00 8.00

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

82

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 6-892 6-458 6-934 2-282 2-385 2-461 6-938 6-1326 6-1335 6-1242 2-462 6-1352 6-165 6-164 6-173 6-215 6-1851 5-525 6-1937 6-741 6-898 6-734 6-1584 2-283 2-386 2-463 6-331 6-939 6-158 6-1256 6-1435 2-464 6-578 6-909 6-835 6-1521 6-669 6-1843 6-1674 6-530 2-284 2-387 2-465 6-1128 6-1753 6-1008 6-1072 6-799 2-466 6-1934

Ød Crossmm sect. d2 400.00 5.00 400.00 12.00 401.71 3.53 405.26 3.53 405.26 5.33 405.26 6.99 409.00 6.99 410.00 6.00 412.00 8.00 415.00 14.20 417.96 6.99 419.30 5.70 420.00 3.50 420.00 5.00 422.00 2.00 425.00 6.00 425.33 5.33 425.83 3.18 428.00 5.00 428.00 5.70 429.00 6.00 430.00 12.00 430.00 16.00 430.66 3.53 430.66 5.33 430.66 6.99 431.80 7.10 434.00 6.99 437.00 3.00 440.00 4.00 440.00 4.30 443.36 6.99 445.00 8.00 449.00 12.00 449.50 6.99 450.00 2.62 450.00 10.00 455.00 5.33 455.00 6.00 455.00 8.00 456.06 3.53 456.06 5.33 456.06 6.99 460.00 5.34 460.00 6.99 463.00 7.00 465.00 5.00 468.00 6.00 468.76 6.99 469.00 5.33

Parker No. 6-2015 6-827 6-930 6-1219 6-1243 6-256 2-388 2-467 6-1979 6-834 6-1080 6-1444 6-2073 2-468 6-328 6-1221 6-1420 6-800 6-261 6-260 2-389 2-469 6-2065 6-202 6-394 6-1837 6-1170 6-775 6-919 6-1158 6-1957 6-1823 6-529 6-951 6-467 6-262 6-1838 2-390 2-470 6-179 6-1409 6-621 6-1608 6-1299 6-836 6-690 6-1641 6-670 6-1952 2-391

Ød Crossmm sect. d2 470.00 4.50 470.00 10.00 477.00 10.50 480.00 4.00 480.00 14.00 480.06 10.00 481.41 5.33 481.46 6.99 484.00 8.40 484.86 3.53 485.00 5.00 490.00 5.00 492.00 3.53 494.16 6.99 500.00 3.53 500.00 5.00 500.00 6.00 500.00 8.00 504.00 6.99 506.00 2.62 506.81 5.33 506.86 6.99 510.00 3.00 514.00 8.00 514.00 8.00 515.00 5.33 515.00 5.00 515.00 10.00 515.90 6.00 520.00 5.00 522.00 4.00 522.00 10.00 524.00 10.00 526.00 6.99 528.00 8.00 532.00 7.00 532.18 5.33 532.21 5.33 532.26 6.99 533.40 3.18 534.00 8.00 535.46 7.24 538.00 6.00 540.00 5.00 543.50 6.99 546.00 7.00 546.00 2.62 550.00 10.00 555.00 3.00 557.61 5.33

Parker No. 2-471 6-462 6-1964 6-1229 6-709 6-1678 6-176 6-1300 6-626 6-1127 2-392 2-472 6-1244 6-1963 6-1953 6-817 6-831 6-380 6-1844 6-2023 6-1858 6-233 6-1301 6-422 6-320 2-473 2-393 6-1220 6-1017 6-742 6-1157 6-647 6-1841 6-265 6-1528 6-278 6-1824 6-247 6-1262 2-394 2-474 6-536 6-986 6-1716 6-235 6-644 6-1308 6-1859 6-1960 6-1959

Ød Crossmm sect. d2 557.66 6.99 558.00 10.00 560.00 7.00 564.30 6.99 565.00 7.00 571.00 8.00 577.85 6.99 579.00 5.00 580.00 8.00 580.50 3.53 582.68 5.33 582.68 6.99 585.00 14.00 587.00 7.00 589.00 3.00 590.00 10.00 590.00 3.50 594.51 7.14 595.00 5.33 598.00 7.00 602.00 7.00 602.00 8.00 602.00 5.00 607.00 4.00 608.00 10.00 608.08 6.99 608.08 5.33 610.00 4.00 613.92 6.99 614.00 7.00 615.00 5.00 617.00 7.00 618.50 2.00 619.50 8.00 621.00 8.50 622.00 8.00 623.08 5.33 624.00 6.99 632.00 6.00 633.48 5.33 633.48 6.99 635.00 5.00 635.00 9.00 635.00 10.00 637.00 10.00 638.89 5.44 640.00 6.00 640.00 7.00 645.00 3.53 645.00 4.00

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

83

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – O-ring sizes acc. to inner diameter d

Sizing charts – O-ring sizes acc. to inner diameter d Parker No. 6-381 2-395 2-475 6-1418 6-653 6-645 6-816 6-1443 6-301 6-535 6-236 6-1742 6-266 6-1160 6-701 6-321 5-092 6-702 6-668 6-531 6-521 6-372 6-389 6-267 6-1245 6-305 6-1847 6-1577 6-1309 6-228 6-1840 6-943 6-2067 6-1079 6-1071 6-417 6-303 6-1173 6-1222 6-667 6-1944 6-1215 6-248 6-1956 6-237 6-649 6-415 6-2042 6-279 6-322

Ød Crossmm sect. d2 647.70 6.99 658.88 5.33 658.88 6.99 661.00 14.00 664.00 5.00 665.00 5.00 670.00 10.00 675.00 5.30 677.00 7.00 680.00 5.00 689.00 10.00 690.00 8.00 693.50 10.10 695.00 5.00 695.00 6.99 700.00 10.00 701.68 6.99 707.00 6.99 708.00 10.00 710.00 5.33 716.00 8.00 720.00 6.99 723.90 6.99 734.00 6.99 735.00 15.00 736.00 3.53 736.00 7.00 736.60 5.00 740.00 6.00 740.00 10.00 745.00 10.00 748.50 7.00 750.00 3.00 750.00 5.00 755.00 5.00 760.00 5.00 763.01 6.99 764.00 6.99 770.00 7.00 770.00 10.00 777.00 12.00 780.00 7.00 783.00 6.99 786.00 4.00 786.00 10.00 798.00 7.00 800.00 5.33 801.00 4.00 810.00 7.10 810.00 10.00

Parker No. 6-1943 6-509 6-2066 6-648 6-268 6-1131 6-229 6-190 6-1130 6-508 6-330 6-650 6-1246 6-2009 6-1223 6-707 6-363 6-890 6-597 6-230 6-304 6-1156 6-924 6-249 6-335 6-708 6-250 6-409 6-269 6-302 6-334 6-527 6-232 6-460 6-534 6-1213 6-332 6-280 6-2124 6-239 6-333 6-270 6-393 6-385 6-240 6-271 6-245 6-1304 6-1325 6-1066

Ød Crossmm sect. d2 818.00 12.00 819.00 7.00 820.00 3.00 820.00 7.00 827.00 7.00 835.50 7.00 837.00 10.00 840.00 12.00 840.50 7.00 849.00 7.00 850.00 10.00 853.00 7.00 853.00 20.00 855.00 10.00 860.00 3.00 865.00 8.40 865.00 12.00 870.00 8.00 875.00 8.00 882.00 10.00 887.00 6.99 890.00 5.00 900.00 10.00 910.00 6.99 914.00 5.33 929.00 6.00 936.00 6.99 940.00 10.00 950.50 12.06 955.00 12.60 960.00 5.33 974.00 7.00 984.00 10.00 996.00 7.00 1004.00 8.00 1005.00 15.00 1011.00 5.33 1016.00 7.00 1020.00 5.70 1029.00 10.00 1042.00 5.33 1046.00 7.00 1060.00 10.00 1071.00 14.40 1075.00 10.00 1103.00 10.00 1154.00 10.00 1840.00 5.00 1865.00 5.00 1960.00 10.85

Parker No. 6-1067 6-1845 6-1846 6-984

Ød Crossmm sect. d2 2072.00 10.00 2324.00 6.99 2350.00 6.99 2965.00 7.00

For articles printed in bold, fitting Parker Parbak® back-up rings are available from stock.

84

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parbak® Back-up ring

Parbak® Back-up ring Parbak® Back-up rings prevent extrusion in high-pressure applications, help to maintain the lubricant film and thus prolong the service life of O-rings. Developed primarily for service in hydraulic fluids at –40 °C to 120 °C, Parker‘s standard Parbak® N0300-90 compound provide the maximum benefits in back-up ring service. Compounds for use in other fluids and for temperatures up to 200 °C are available on request. Parbaks will stretch up to 50 %, and are quickly and easily installed. Advantages of the contour design are obtained regardless of how Parbaks are installed — they may be installed, toward or away from the O-ring.

A

Szczegół A

W

R

T

Szczegół A

85

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

ØM

Sizing charts – Parbak® back-up ring 8-xxx sizes Parker No. 8-004 8-005 8-006 8-007 8-008 8-009 8-010 8-011 8-012 8-013 8-014 8-015 8-016 8-017 8-018 8-019 8-020 8-021 8-022 8-023 8-024 8-025 8-026 8-027 8-028 8-029 8-030 8-031 8-032 8-033 8-034 8-035 8-036 8-037 8-038 8-039 8-040 8-041 8-042 8-043 8-044 8-045 8-046 8-047 8-048 8-049 8-050 8-102

M W ±0.08 (mm) (mm) 2.44 1.35 3.23 1.35 3.56 1.35 4.34 1.35 5.13 1.35 5.94 1.35 6.73 1.35 8.31 1.35 9.91 1.35 11.56 1.35 13.16 1.35 14.73 1.35 16.33 1.35 17.91 1.35 19.51 1.35 21.08 1.35 22.68 1.35 24.26 1.35 25.86 1.35 27.43 1.35 29.03 1.35 30.61 1.35 32.21 1.35 33.78 1.35 35.38 1.35 38.56 1.35 41.73 1.35 44.91 1.35 48.08 1.35 51.26 1.35 54.43 1.35 57.61 1.35 60.78 1.35 63.96 1.35 67.13 1.35 70.31 1.35 73.48 1.35 76.66 1.35 83.01 1.35 89.36 1.35 95.71 1.35 102.06 1.35 108.41 1.35 114.76 1.35 121.11 1.35 127.46 1.35 133.81 1.35 1.96 2.18

Parker No. 8-103 8-104 8-105 8-106 8-107 8-108 8-109 8-110 8-111 8-112 8-113 8-114 8-115 8-116 8-117 8-118 8-119 8-120 8-121 8-122 8-123 8-124 8-125 8-126 8-127 8-128 8-129 8-130 8-131 8-132 8-133 8-134 8-135 8-136 8-137 8-138 8-139 8-140 8-141 8-142 8-143 8-144 8-145 8-146 8-147 8-148 8-149 8-150

M W ±0.08 (mm) (mm) 2.77 2.18 3.56 2.18 4.34 2.18 5.13 2.18 5.94 2.18 6.73 2.18 8.31 2.18 9.91 2.18 11.48 2.18 13.08 2.18 14.66 2.18 16.26 2.18 17.83 2.18 19.43 2.18 21.11 2.18 22.68 2.18 24.28 2.18 25.86 2.18 27.46 2.18 29.03 2.18 30.63 2.18 32.21 2.18 33.81 2.18 35.38 2.18 36.98 2.18 38.56 2.18 40.16 2.18 41.73 2.18 43.33 2.18 44.91 2.18 46.51 2.18 48.08 2.18 49.68 2.18 51.26 2.18 52.86 2.18 54.43 2.18 56.03 2.18 57.61 2.18 59.21 2.18 60.78 2.18 62.38 2.18 63.96 2.18 65.56 2.18 67.13 2.18 68.73 2.18 70.31 2.18 71.91 2.18 73.48 2.18

86

Parker No. 8-151 8-152 8-153 8-154 8-155 8-156 8-157 8-158 8-159 8-160 8-161 8-162 8-163 8-164 8-165 8-166 8-167 8-168 8-169 8-170 8-171 8-172 8-173 8-174 8-175 8-176 8-177 8-178

M W ±0.08 (mm) (mm) 76.66 2.18 83.01 2.18 89.36 2.18 95.71 2.18 102.06 2.18 108.41 2.18 114.76 2.18 121.11 2.18 127.46 2.18 133.81 2.18 140.16 2.18 146.51 2.18 152.86 2.18 159.21 2.18 165.56 2.18 171.91 2.18 178.26 2.18 184.61 2.18 190.96 2.18 197.31 2.18 203.66 2.18 210.01 2.18 216.36 2.18 222.71 2.18 229.06 2.18 235.41 2.18 241.76 2.18 248.11 2.18

O-Ring Guide Parker Hannifin O-Ring Division Europe

Parker No. 8-201 8-202 8-203 8-204 8-205 8-206 8-207 8-208 8-209 8-210 8-211 8-212 8-213 8-214 8-215 8-216 8-217 8-218 8-219 8-220 8-221 8-222 8-223 8-224 8-225 8-226 8-227 8-228 8-229 8-230 8-231 8-232 8-233 8-234 8-235 8-236 8-237 8-238 8-239 8-240 8-241 8-242 8-243 8-244 8-245 8-246 8-247 8-248

M W ±0.1 (mm) (mm) 5.13 3.00 6.73 3.00 8.30 3.00 9.90 3.00 11.56 3.00 13.16 3.00 14.73 3.00 16.33 3.00 17.90 3.00 19.46 3.00 21.03 3.00 22.63 3.00 24.21 3.00 25.81 3.00 27.38 3.00 28.98 3.00 30.56 3.00 32.16 3.00 33.88 3.00 35.48 3.00 37.06 3.00 38.66 3.00 41.83 3.00 45.01 3.00 48.18 3.00 51.36 3.00 54.53 3.00 57.71 3.00 60.88 3.00 64.06 3.00 66.83 3.00 70.00 3.00 73.18 3.00 76.35 3.00 79.53 3.00 82.70 3.00 85.88 3.00 89.05 3.00 92.23 3.00 95.40 3.00 98.58 3.00 101.75 3.00 104.93 3.00 108.10 3.00 111.28 3.00 114.45 3.00 117.63 3.00 121.11 3.00

Parker No. 8-249 8-250 8-251 8-252 8-253 8-254 8-255 8-256 8-257 8-258 8-259 8-260 8-261 8-262 8-263 8-264 8-265 8-266 8-267 8-268 8-269 8-270 8-271 8-272 8-273 8-274 8-275 8-276 8-277 8-278 8-279 8-280 8-281 8-282 8-283 8-284

M W ±0.1 (mm) (mm) 124.28 3.00 127.46 3.00 130.63 3.00 133.81 3.00 136.98 3.00 140.16 3.00 143.33 3.00 146.51 3.00 149.68 3.00 152.86 3.00 159.21 3.00 165.56 3.00 171.91 3.00 178.26 3.00 184.61 3.00 190.96 3.00 197.31 3.00 203.66 3.00 210.01 3.00 216.36 3.00 222.71 3.00 229.06 3.00 235.41 3.00 241.76 3.00 248.11 3.00 254.46 3.00 267.16 3.00 279.86 3.00 292.56 3.00 305.26 3.00 330.66 3.00 356.05 3.00 381.46 3.00 406.12 3.00 431.52 3.00 456.92 3.00

87

Parker No. 8-309 8-310 8-311 8-312 8-313 8-314 8-315 8-316 8-317 8-318 8-319 8-320 8-321 8-322 8-323 8-324 8-325 8-326 8-327 8-328 8-329 8-330 8-331 8-332 8-333 8-334 8-335 8-336 8-337 8-338 8-339 8-340 8-341 8-342 8-343 8-344 8-345 8-346 8-347 8-348 8-349 8-350 8-351 8-352 8-353 8-354 8-355 8-356

M (mm) 11.43 13.03 14.60 16.20 17.78 19.38 20.96 22.56 24.13 25.73 27.31 28.91 30.42 32.08 33.43 35.26 38.43 41.61 44.78 47.96 51.13 54.31 57.61 60.78 63.96 67.13 70.31 73.48 76.66 79.83 83.13 86.31 89.48 92.66 95.83 99.01 102.31 105.49 108.66 111.84 115.01 118.19 121.36 124.54 127.71 130.89 134.09 137.24

W ±0.13 (mm) 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Sizing charts – Parbak® back-up ring 8-xxx sizes

Sizing charts – Parbak® back-up ring 8-xxx sizes Parker No. 8-357 8-358 8-359 8-360 8-361 8-362 8-363 8-364 8-365 8-366 8-367 8-368 8-369 8-370 8-371 8-372 8-373 8-374 8-375 8-376 8-377 8-378 8-379 8-380 8-381 8-382 8-383 8-384 8-385 8-386 8-387 8-388 8-389 8-390 8-391 8-392 8-393 8-394 8-395

M (mm) 140.41 143.59 146.76 149.94 153.11 159.46 165.81 172.16 178.51 184.86 191.21 197.56 203.91 210.26 216.61 222.96 229.31 235.66 242.01 248.36 254.71 267.41 280.11 292.81 305.51 330.91 356.31 381.71 406.60 432.00 457.40 482.75 508.15 533.55 558.95 584.02 609.42 634.82 660.22

W ±0.13 (mm) 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65 4.65

Parker No. 8-425 8-426 8-427 8-428 8-429 8-430 8-431 8-432 8-433 8-434 8-435 8-436 8-437 8-438 8-439 8-440 8-441 8-442 8-443 8-444 8-445 8-446 8-447 8-448 8-449 8-450 8-451 8-452 8-453 8-454 8-455 8-456 8-457 8-458 8-459 8-460 8-461 8-462 8-463 8-464 8-465 8-466 8-467 8-468 8-469 8-470 8-471 8-472

W ±0.15 (mm) 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99 5.99

M (mm) 115.60 118.77 121.95 125.20 128.30 131.47 134.65 137.82 141.00 144.17 147.35 150.52 153.70 159.36 165.71 172.06 178.41 184.76 191.11 197.46 203.81 216.51 229.21 241.91 254.61 267.31 280.01 292.71 305.41 318.11 330.81 343.51 356.21 368.91 381.61 394.31 406.50 419.20 431.90 444.60 457.30 470.00 482.70 495.40 508.10 533.50 558.90 584.30

88

Parker M No. (mm) 8-473 609.70 8-474 635.10 8-475 660.50

W ±0.15 (mm) 5.99 5.99 5.99

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts – Parbak® back-up ring other dimensions Other dimensions 004-050 102-178 201-284 309-395 425-475

R (mm) 2.21 3.28 4.42 6.65 8.74

Size tolerances Parker No. M± 004-009 0.15 mm 009-012 0.18 mm 012-019 0.23 mm 020-029 1.00 % 030-041 0.86 % 042-050 0.78 % 102-107 0.15 mm 108-110 0.18 mm 111-117 0.25 mm 118-128 1.10 % 129-151 0.95 % 152-164 0.78 % 165-178 0.74 % 201-204 0.18 mm 204-211 0.25 mm 212-227 1.10 % 228-235 0.90 % 236-259 0.78 % 260-277 0.74 % 278-284 0.67 % 309-315 0.25 mm 316-325 1.10 % 326-338 0.95 % 339-362 0.78 % 363-380 0.74 % 381-395 0.67 % 425-438 0.78 % 439-452 0.74 % 453-475 0.67 %

T (mm) 1.24 1.35 1.27 1.93 2.97

A (mm) 1.14 1.14 1.02 1.52 2.44

Size tolerances Parker No. A ± 004-284 0.08 mm 309-325 0.10 mm 425-475 0.13 mm

Please note: 1. On ordering both size and compound should be stated e.g. 8-130, N300-90. 2. Parbak® size numbers correspond to O-rings in the 2-xxx series, e.g. 8-211, N 300-90 is fitted with the O-ring 2-211, N 674-70.

89

O-Ring Guide Parker Hannifin O-Ring Division Europe

Sizing charts

Parker No.

Notes

90

O-Ring Guide Parker Hannifin O-Ring Division Europe

Notes

91

O-Ring Guide Parker Hannifin O-Ring Division Europe

Notes

92

O-Ring Guide Parker Hannifin O-Ring Division Europe

Notes

93

O-Ring Guide Parker Hannifin O-Ring Division Europe

Notes

94

O-Ring Guide Parker Hannifin O-Ring Division Europe

© 2015 Parker Hannifin Corporation · Subject to change

ODE 5712 EN · Pdf · 07/2015

Parker Hannifin GmbH Engineered Materials Group Europe P.O. Box 1641 74306 Bietigheim-Bissingen ∙ Tel. +49 (0) 7142 351-0 Fax +49 (0) 7142 351-293 www.parker.com/praedifa e-mail: [email protected]