Planetary Gearset 1g40q

1-4 PLANETARY GEARSET It is often necessary to design gear trains that will provide many gear ratios. Of necessity, these trains must not be too large and bulky. The answer to this requirement is planetary gearing.

FIGURE 9. PLANETARY GEAR SYSTEM.

Notice the arrangement of the components in the set. Because of the resemblance of the planetary pinions to the planets of the universe circling around the sun, the set was given the name planetary gearset. The center or sun gear can be either a spur gear or helical gear. It will contain a through shaft so that it can act as either an input or output member.

Normally, three planetary pinions are in mesh with the sun gear at all times. Some sets will have two and others four. They are mounted on and are free to rotate on individual shafts on the planet carrier, which is a framework designed to hold the pinions in their respective positions. The planet carrier can be rotated so that the pinions walk around the sun gear. The carrier also contains a shaft so that it may act as an input or output member. The outer internal gear is in constant mesh with the planet pinions and is called the ring gear. It can also be an input or output member. The principle on which the planetary gearset operates is based on driving one unit, holding one unit, and taking the output from the free unit. If we place a brake band around the ring gear, we can prevent it from turning. If the sun gear is driven under this condition, it will cause the planet pinions to rotate. With the ring gear held from turning, the planet pinions will have to walk around on the inside of the ring gear and the outside of the sun gear. In doing so, the planet pinions will carry the planet carrier around with them. If the planet carrier is held so that it cannot rotate and the sun gear is driven, the planet pinions will force the ring gear to turn. If the planet carrier is held and the ring gear is driven, the planet pinions will force the sun gear to turn. If the sun gear is held and the planet carrier is driven, the planet pinions will be forced to rotate and they will drive the ring gear. Actual use of planetary gears in such things as automatic transmissions, disk clutches, and brake bands control the holding and driving . Usually, the bands and clutches are controlled automatically. OPERATING PRINCIPLES To fully understand the movement of each member of a planetary system, let's consider a few basic operating principles of a planetary gearset. If the planetary carrier and the sun gear are held together, the pinions cannot turn because they are locked by the sun gear. This will cause the unit to turn as one unit. None of its parts will turn by themselves. This will give us direct drive just as if we had a one-piece shaft. If the sun gear is held and the planetary carrier is turned, then the ring gear will turn. The pinions will "walk" around the sun gear because the sun gear will not move. The pinions turn as they walk around the sun gear and are in mesh with the ring gear; therefore, the ring gear is pushed by the turning pinion. The ring gear will turn in the same direction as the carrier. If the ring gear is held and the sun gear is turned, then the carrier will turn. The pinions are in mesh with the sun gear, and, when the sun gear is turned, the pinions will turn. The pinions are also in mesh with the ring gear. With the ring gear held, the pinions therefore walk around the ring gear. This causes the carrier to turn with the pinions. If the carrier is held and the sun gear is turned, then the ring gear turns in reverse. Because the pinions are in mesh with the sun gear, when the sun gear is turned, the pinions also turn. However, the pinions turn in the opposite direction of the sun gear. The pinions are also in mesh with the ring gear and drive the ring gear because the carrier is held so that it cannot turn. When

an external gear is driving an internal gear, the direction of turning is the same. Therefore, the planet pinions turning opposite from the input rotate the ring gear in reverse. There are five basic rules of planetary gear operation: • • • • •

If the planet carrier is used as the output, the set operates in reduction (slower speed, more torque). If the planet carrier is the input, the set operates in overdrive (more speed, less torque). If the planet carrier is held, the set operates in reverse. If any two parts are locked together, the set operates in direct drive. If no parts are locked together and if none are held, the set operates in neutral.

Here are a few more things you should also . • • • •

An input member receives power from a source such as an engine. An output member transmits power to the driving wheels of a vehicle. A stationary member is one that is held by a band or clutch so that it cannot turn. Locked are held together.

SPEED RANGES OF A PLANETARY SET Using the first three of the above rules, we can get six speed ranges. , when we reduce speed, we increase torque, and when we increase speed, we reduce torque. • • • • • •

If the sun gear is held and the planet carrier is turned, the ring gear will turn faster than the carrier (overdrive). If the sun gear is held and the ring gear is turned, the planet carrier will turn slower than the ring gear (reduction). If the ring gear is held and the sun gear is turned, the planet carrier turns slower than the sun gear (reduction). If the planet carrier is held and the ring gear is turned, the sun gear turns in reverse faster than the ring gear (overdrive and reverse). If the ring gear is held and the planet carrier is turned, the sun gear turns faster than the carrier (overdrive). If the planet carrier is held and the sun gear is turned, the ring gear turns in reverse slower than the sun gear (reduction and reverse).