Sae As568d 4l5c1i
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report 3i3n4
Overview 26281t
& View Sae As568d as PDF for free.
More details 6y5l6z
- Words: 5,921
- Pages: 15
AS568
AEROSPACE STANDARD
Issued Revised
REV. D 1971-07 2014-03
Superseding AS568C
Aerospace Size Standard for O-rings RATIONALE The drawing has been revised to eliminate the parting line projection shown in earlier issues since it is not applicable to an O-ring size standard. 1. SCOPE 1.1
Purpose
This SAE Aerospace Standard (AS) specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. The dimensions and tolerances specified in this standard are suitable for any elastomeric material provided that suitable tooling is available. 1.2
Application
1.2.1
This standard is intended to be used in the preparation of Company, Military, or other Standard Drawings for O-rings. Each dash number, which should be appended to an appropriate Drawing or Standard number, identifies one nominal size O-ring only.
1.2.2
No attempt is made in this AS to indicate which of the O-ring sizes listed under this system should be included in any particular Standard Drawing. Its only purpose is to standardize O-ring sizes and dimensional tolerances and the means of identifying them dimensionally.
2. REFERENCES There are no referenced publications specified herein. 3. NOTES --`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
3.1
In Table 1, the dash numbers are divided into groups of one hundred, and within each group are sequential and non-significant. Each hundred group, however, identifies the cross section size of the O-rings within the group. For example, all 0.070 inch (1.78 mm) and smaller O-ring cross sections fall into the group of -001 thru -099. The 0.103 inch (2.62 mm) cross section rings fall into the group of -100 thru -199, and so on.
__________________________________________________________________________________________________________________________________________ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the .” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright © 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER:
Provided by IHS SAEorWEB ADDRESS: No reproduction networking permitted without license from IHS
SAE values your input. To provide Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) on this Technical Report, please visit Fax: 724-776-0790 http://www.sae.org/technical/standards/AS568D Email: [email protected] Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo http://www.sae.org Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 2 of 15
3.2
Table 2, using the 900 series dash numbers, lists all of the presently standardized straight thread tube fitting boss gaskets. This series has traditionally utilized the significant dash numbering system, wherein the dash number designates the tube size in 16th’s of an inch. This practice is also followed here, with the exception of the -901, which is intended for a 0.0938 inch (2.38 mm) nominal OD (outside diameter) tube, the 0.0625 inch (1.59 mm) OD tube not being in common aircraft use.
3.3
In the interest of standardization, it is requested that companies or agencies do not use the dash numbers in Table 1 to which sizes have not been assigned. Sizes not assigned are indicated by an asterisk (*). Anyone feeling that any special size not now shown is widely enough used to justify standardization should direct such a request to SAE A-6 Committee for coordination.
3.4
Figure 1 illustrates that all diameters of the cross-section should be equal.
FIGURE 1 - O-RING DIMENSIONS: WIDTH (W) AND INSIDE DIAMETER (D) 3.5
A change bar (l) located in the left margin is for the convenience of the in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 3 of 15
Dash Number -001 -002 -003 -004 -005
ID Inches min 0.025 0.038 0.052 0.065 0.096
ID Inches max 0.033 0.046 0.060 0.075 0.106
ID mm min 0.64 0.97 1.32 1.65 2.44
ID mm max 0.84 1.17 1.52 1.91 2.69
W Inches min 0.037 0.047 0.057 0.067 0.067
W Inches max 0.043 0.053 0.063 0.073 0.073
W mm min 0.94 1.19 1.45 1.70 1.70
W mm max 1.09 1.35 1.60 1.85 1.85
Volume (Ref) Cubic Inches 0.0003 0.0006 0.0010 0.0017 0.0021
Volume (Ref) Cubic cm 0.005 0.010 0.016 0.028 0.034
-006 -007 -008 -009 -010
0.109 0.140 0.171 0.203 0.234
0.119 0.150 0.181 0.213 0.244
2.77 3.56 4.34 5.16 5.94
3.02 3.81 4.60 5.41 6.20
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0022 0.0026 0.0030 0.0034 0.0037
0.036 0.043 0.049 0.056 0.061
-011 -012 -013 -014 -015
0.296 0.359 0.421 0.484 0.544
0.306 0.369 0.431 0.494 0.558
7.52 9.12 10.69 12.29 13.82
7.77 9.37 10.95 12.55 14.17
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0045 0.0052 0.0060 0.0068 0.0075
0.074 0.085 0.098 0.111 0.123
-016 -017 -018 -019 -020
0.605 0.667 0.730 0.792 0.855
0.623 0.685 0.748 0.810 0.873
15.37 16.94 18.54 20.12 21.72
15.82 17.40 19.00 20.57 22.17
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0083 0.0090 0.0098 0.0105 0.0113
0.136 0.147 0.161 0.172 0.185
-021 -022 -023 -024 -025
0.917 0.979 1.041 1.104 1.165
0.935 0.999 1.061 1.124 1.187
23.29 24.87 26.44 28.04 29.59
23.75 25.37 26.95 28.55 30.15
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0120 0.0128 0.0136 0.0143 0.0151
0.197 0.210 0.223 0.234 0.247
-026 -027 -028 -029 -030
1.228 1.290 1.351 1.476 1.601
1.250 1.312 1.377 1.502 1.627
31.19 32.77 34.32 37.49 40.67
31.75 33.32 34.98 38.15 41.33
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0158 0.0166 0.0173 0.0188 0.0204
0.259 0.272 0.283 0.308 0.334
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS
SAE INTERNATIONAL
AS568D
Page 4 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
ID Inches max 1.754 1.879 2.007 2.132 2.257
ID mm min 43.79 46.96 50.06 53.24 56.41
ID mm max 44.55 47.73 50.98 54.15 57.33
W Inches min 0.067 0.067 0.067 0.067 0.067
W Inches max 0.073 0.073 0.073 0.073 0.073
W mm min 1.70 1.70 1.70 1.70 1.70
W mm max 1.85 1.85 1.85 1.85 1.85
Volume (Ref) Cubic Inches 0.0219 0.0234 0.0249 0.0264 0.0279
Volume (Ref) Cubic cm 0.359 0.383 0.408 0.433 0.457
-036 -037 -038 -039 -040
2.346 2.471 2.594 2.719 2.844
2.382 2.507 2.634 2.759 2.884
59.59 62.76 65.89 69.06 72.24
60.50 63.68 66.90 70.08 73.25
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0294 0.0309 0.0325 0.0340 0.0355
0.482 0.506 0.533 0.557 0.582
-041 -042 -043 -044 -045
2.965 3.215 3.465 3.712 3.962
3.013 3.263 3.513 3.766 4.016
75.31 81.66 88.01 94.28 100.63
76.53 82.88 89.23 95.66 102.01
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0370 0.0400 0.0430 0.0461 0.0491
0.606 0.655 0.705 0.755 0.805
-046 -047 -048 -049 -050
4.209 4.459 4.709 4.952 5.202
4.269 4.519 4.769 5.026 5.276
106.91 113.26 119.61 125.78 132.13
108.43 114.78 121.13 127.66 134.01
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0521 0.0551 0.0581 0.0612 0.0642
0.854 0.903 0.952 1.003 1.052
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Dash Number -031 -032 -033 -034 -035
ID Inches min 1.724 1.849 1.971 2.096 2.221
*051 THRU *101 -102 -103 -104 -105
*O-RING SIZES NOT ASSIGNED 0.044 0.076 0.107 0.138
Provided by IHS No reproduction or networking permitted without license from IHS
0.054 0.086 0.117 0.148
1.12 1.93 2.72 3.51
1.37 2.18 2.97 3.76
0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69
0.0040 0.0048 0.0056 0.0064
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
0.066 0.079 0.092 0.105
SAE INTERNATIONAL
AS568D
Page 5 of 15
Dash Number -106 -107 -108 -109 -110
ID Inches min 0.169 0.201 0.232 0.294 0.357
ID Inches max 0.179 0.211 0.242 0.304 0.367
ID mm min 4.29 5.11 5.89 7.47 9.07
ID mm max 4.55 5.36 6.15 7.72 9.32
W Inches min 0.100 0.100 0.100 0.100 0.100
W Inches max 0.106 0.106 0.106 0.106 0.106
W mm min 2.54 2.54 2.54 2.54 2.54
W mm max 2.69 2.69 2.69 2.69 2.69
Volume (Ref) Cubic Inches 0.0073 0.0081 0.0089 0.0105 0.0122
Volume (Ref) Cubic cm 0.120 0.133 0.146 0.172 0.200
-111 -112 -113 -114 -115
0.419 0.482 0.542 0.603 0.665
0.429 0.492 0.556 0.621 0.683
10.64 12.24 13.77 15.32 16.89
10.90 12.50 14.12 15.77 17.35
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0138 0.0154 0.0171 0.0187 0.0203
0.226 0.252 0.280 0.306 0.333
-116 -117 -118 -119 -120
0.728 0.789 0.852 0.914 0.977
0.746 0.809 0.872 0.934 0.997
18.49 20.04 21.64 23.22 24.82
18.95 20.55 22.15 23.72 25.32
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0220 0.0236 0.0253 0.0269 0.0285
0.361 0.387 0.415 0.441 0.467
-121 -122 -123 -124 -125
1.039 1.102 1.162 1.225 1.287
1.059 1.122 1.186 1.249 1.311
26.39 27.99 29.51 31.12 32.69
26.90 28.50 30.12 31.72 33.30
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0302 0.0318 0.0334 0.0351 0.0367
0.495 0.521 0.547 0.575 0.601
-126 -127 -128 -129 -130
1.350 1.412 1.475 1.534 1.597
1.374 1.436 1.499 1.564 1.627
34.29 35.86 37.46 38.96 40.56
34.90 36.47 38.07 39.73 41.33
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0383 0.0400 0.0416 0.0432 0.0449
0.628 0.655 0.682 0.708 0.736
-131 -132 -133 -134 -135
1.659 1.722 1.784 1.847 1.908
1.689 1.752 1.814 1.877 1.942
42.14 43.74 45.31 46.91 48.46
42.90 44.50 46.08 47.68 49.33
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0465 0.0482 0.0498 0.0514 0.0531
0.762 0.790 0.816 0.842 0.870
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
SAE INTERNATIONAL
AS568D
Page 6 of 15
Dash Number -136 -137 -138 -139 -140
ID Inches min 1.970 2.033 2.095 2.158 2.220
ID Inches max 2.004 2.067 2.129 2.192 2.254
ID mm min 50.04 51.64 53.21 54.81 56.39
ID mm max 50.90 52.50 54.08 55.68 57.25
W Inches min 0.100 0.100 0.100 0.100 0.100
W Inches max 0.106 0.106 0.106 0.106 0.106
W mm min 2.54 2.54 2.54 2.54 2.54
W mm max 2.69 2.69 2.69 2.69 2.69
Volume (Ref) Cubic Inches 0.0547 0.0564 0.0580 0.0596 0.0613
Volume (Ref) Cubic cm 0.896 0.924 0.950 0.977 1.005
-141 -142 -143 -144 -145
2.280 2.342 2.405 2.467 2.530
2.320 2.382 2.445 2.507 2.570
57.91 59.49 61.09 62.66 64.26
58.93 60.50 62.10 63.68 65.28
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0629 0.0645 0.0662 0.0678 0.0694
1.031 1.057 1.085 1.111 1.137
-146 -147 -148 -149 -150
2.592 2.653 2.715 2.778 2.840
2.632 2.697 2.759 2.822 2.884
65.84 67.39 68.96 70.56 72.14
66.85 68.50 70.08 71.68 73.25
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0711 0.0727 0.0743 0.0760 0.0776
1.165 1.191 1.218 1.245 1.272
-151 -152 -153 -154 -155
2.963 3.213 3.463 3.709 3.959
3.011 3.261 3.511 3.765 4.015
75.26 81.61 87.96 94.21 100.56
76.48 82.83 89.18 95.63 101.98
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0809 0.0874 0.0940 0.1005 0.1071
1.326 1.432 1.540 1.647 1.755
-156 -157 -158 -159 -160
4.207 4.457 4.707 4.952 5.202
4.267 4.517 4.767 5.022 5.272
106.86 113.21 119.56 125.78 132.13
108.38 114.73 121.08 127.56 133.91
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.1136 0.1202 0.1267 0.1332 1.1398
1.862 1.970 2.076 2.183 2.291
-161 -162 -163 -164 -165
5.452 5.702 5.952 6.197 6.447
5.522 5.772 6.022 6.277 6.527
138.48 144.83 151.18 157.40 163.75
140.26 146.61 152.96 159.44 165.79
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.1463 0.1529 0.1594 0.1660 0.1725
2.397 2.506 2.612 2.720 2.827
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
SAE INTERNATIONAL
AS568D
Page 7 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -166 -167 -168 -169 -170
ID Inches min 6.697 6.947 7.192 7.442 7.692
ID Inches max 6.777 7.027 7.282 7.532 7.782
ID mm min 170.10 176.45 182.68 189.03 195.38
ID mm max 172.14 178.49 184.96 191.31 197.66
W Inches min 0.100 0.100 0.100 0.100 0.100
W Inches max 0.106 0.106 0.106 0.106 0.106
W mm min 2.54 2.54 2.54 2.54 2.54
W mm max 2.69 2.69 2.69 2.69 2.69
Volume (Ref) Cubic Inches 0.1790 0.1856 0.1921 0.1987 0.2052
Volume (Ref) Cubic cm 2.933 3.041 3.148 3.256 3.363
-171 -172 -173 -174 -175
7.942 8.187 8.437 8.687 8.937
8.032 8.287 8.537 8.787 9.037
201.73 207.95 214.30 220.65 227.00
204.01 210.49 216.84 223.19 229.54
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.2118 0.2183 0.2249 0.2314 0.2379
3.471 3.577 3.685 3.792 3.898
-176 -177 -178
9.182 9.432 9.682
9.292 9.542 9.792
233.22 239.57 245.92
236.02 242.37 248.72
0.100 0.100 0.100
0.106 0.106 0.106
2.54 2.54 2.54
2.69 2.69 2.69
0.2445 0.2510 0.2576
4.007 4.113 4.221
*O-RING SIZES NOT ASSIGNED
-201 -202 -203 -204 -205
0.166 0.229 0.291 0.354 0.416
0.176 0.239 0.301 0.364 0.426
4.22 5.82 7.39 8.99 10.57
4.47 6.07 7.65 9.25 10.82
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.0148 0.0178 0.0207 0.0237 0.0267
0.243 0.292 0.339 0.388 0.438
-206 -207 -208 -209 -210
0.479 0.539 0.600 0.662 0.724
0.489 0.553 0.618 0.680 0.744
12.17 13.69 15.24 16.81 18.39
12.42 14.05 15.70 17.27 18.90
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.0297 0.0327 0.0357 0.0386 0.0416
0.487 0.536 0.586 0.633 0.682
-211 -212 -213 -214 -215
0.786 0.849 0.911 0.974 1.036
0.806 0.869 0.931 0.994 1.056
19.96 21.56 23.14 24.74 26.31
20.47 22.07 23.65 25.25 26.82
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.0446 0.0476 0.0505 0.0535 0.0565
0.731 0.780 0.828 0.877 0.926
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
*179 THRU *200
SAE INTERNATIONAL
AS568D
Page 8 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
ID Inches max 1.121 1.183 1.246 1.308 1.371
ID mm min 27.86 29.44 31.04 32.61 34.21
ID mm max 28.47 30.05 31.65 33.22 34.82
W Inches min 0.135 0.135 0.135 0.135 0.135
W Inches max 0.143 0.143 0.143 0.143 0.143
W mm min 3.43 3.43 3.43 3.43 3.43
W mm max 3.63 3.63 3.63 3.63 3.63
Volume (Ref) Cubic Inches 0.0595 0.0625 0.0655 0.0684 0.0714
Volume (Ref) Cubic cm 0.975 1.024 1.073 1.121 1.170
-221 -222 -223 -224 -225
1.409 1.469 1.594 1.719 1.841
1.433 1.499 1.624 1.749 1.877
35.79 37.31 40.49 43.66 46.76
36.40 38.07 41.25 44.42 47.68
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.0744 0.0774 0.0833 0.0893 0.0952
1.219 1.268 1.365 1.463 1.560
-226 -227 -228 -229 -230
1.966 2.091 2.214 2.339 2.464
2.002 2.127 2.254 2.379 2.504
49.94 53.11 56.24 59.41 62.59
50.85 54.03 57.25 60.43 63.60
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.1012 0.1072 0.1131 0.1191 0.1250
1.658 1.757 1.853 1.952 2.048
-231 -232 -233 -234 -235
2.589 2.710 2.835 2.960 3.085
2.629 2.758 2.883 3.008 3.133
65.76 68.83 72.01 75.18 78.36
66.78 70.05 73.23 76.40 79.58
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.1310 0.1370 0.1429 0.1489 0.1548
2.147 2.245 2.342 2.440 2.537
-236 -237 -238 -239 -240
3.210 3.335 3.460 3.581 3.706
3.258 3.383 3.508 3.637 3.762
81.53 84.71 87.88 90.96 94.13
82.75 85.93 89.10 92.38 95.55
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.1608 0.1668 0.1727 0.1787 0.1846
2.635 2.733 2.830 2.928 3.025
-241 -242 -243 -244 -245
3.831 3.956 4.081 4.204 4.329
3.887 4.012 4.137 4.264 4.389
97.31 100.48 103.66 106.76 109.96
98.73 101.90 105.08 108.31 111.48
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.1906 0.1966 0.2025 0.2085 0.2144
3.123 3.222 3.318 3.417 3.513
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Dash Number -216 -217 -218 -219 -220
ID Inches min 1.097 1.159 1.222 1.284 1.347
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 9 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
ID Inches max 4.514 4.639 4.764 4.894 5.019
ID mm min 113.13 116.31 119.48 122.53 125.70
ID W mm Inches max min 114.66 0.135 117.83 0.135 121.01 0.135 124.31 0.135 127.48 0.135
W Inches max 0.143 0.143 0.143 0.143 0.143
W mm min 3.43 3.43 3.43 3.43 3.43
W mm max 3.63 3.63 3.63 3.63 3.63
Volume (Ref) Cubic Inches 0.2204 0.2263 0.2323 0.2383 0.2442
Volume (Ref) Cubic cm 3.612 3.708 3.807 3.905 4.002
-251 -252 -253 -254 -255
5.074 5.199 5.324 5.449 5.574
5.144 5.269 5.394 5.519 5.644
128.88 132.05 135.23 138.40 141.58
130.66 133.83 137.01 140.18 143.36
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.2502 0.2561 0.2621 0.2681 0.2740
4.100 4.197 4.295 4.393 4.490
-256 -257 -258 -259 -260
5.699 5.824 5.949 6.194 6.444
5.769 5.894 6.019 6.274 6.524
144.75 147.93 151.10 157.33 163.68
146.53 149.71 152.88 159.36 165.71
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.2800 0.2859 0.2919 0.3038 0.3157
4.588 4.685 4.783 4.978 5.173
-261 -262 -263 -264 -265
6.694 6.944 7.189 7.439 7.689
6.774 7.024 7.279 7.529 7.779
170.03 176.38 182.60 188.95 195.30
172.06 178.41 184.89 191.24 197.59
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.3277 0.3396 0.3515 0.3634 0.3753
5.370 5.565 5.760 5.955 6.150
-266 -267 -268 -269 -270
7.939 8.184 8.434 8.684 8.934
8.029 8.284 8.534 8.784 9.034
201.65 207.87 214.22 220.57 226.92
203.94 210.41 216.76 223.11 229.46
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.3872 0.3992 0.4111 0.4230 0.4349
6.345 6.542 6.737 6.932 7.127
-271 -272 -273 -274 -275
9.179 9.429 9.679 9.929 10.429
9.289 9.539 9.789 10.039 10.539
233.15 239.50 245.85 252.20 264.90
235.94 242.29 248.64 254.99 267.69
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.4468 0.4588 0.4707 0.4826 0.5064
7.322 7.518 7.713 7.908 8.298
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Dash Number -246 -247 -248 -249 -250
ID Inches min 4.454 4.579 4.704 4.824 4.949
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 10 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -276 -277 -278 -279 -280
ID Inches min 10.919 11.419 11.919 12.919 13.919
ID Inches max 11.049 11.549 12.049 13.049 14.049
ID mm min 277.34 290.04 302.74 328.14 353.54
ID W mm Inches max min 280.64 0.135 293.34 0.135 306.04 0.135 331.44 0.135 356.84 0.135
W Inches max 0.143 0.143 0.143 0.143 0.143
W mm min 3.43 3.43 3.43 3.43 3.43
W mm max 3.63 3.63 3.63 3.63 3.63
Volume (Ref) Cubic Inches 0.5303 0.5541 0.5779 0.6256 0.6733
Volume (Ref) Cubic cm 8.690 9.080 9.470 10.252 11.033
-281 -282 -283 -284
14.919 15.880 16.875 17.870
15.049 16.030 17.035 18.040
378.94 403.35 428.63 453.90
382.24 407.16 432.69 458.22
0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63
0.7210 0.7672 0.8149 0.8626
11.815 12.572 13.354 14.136
*285 THRU *308
*O-RING SIZES NOT ASSIGNED
-309 -310
0.407 0.470
0.417 0.480
10.34 11.94
10.59 12.19
0.205 0.205
0.215 0.215
5.21 5.21
5.46 5.46
0.0677 0.0745
1.109 1.221
-311 -312 -313 -314 -315
0.530 0.591 0.653 0.715 0.777
0.544 0.609 0.671 0.735 0.797
13.46 15.01 16.59 18.16 19.74
13.82 15.47 17.04 18.67 20.24
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.0813 0.0881 0.0949 0.1017 0.1085
1.332 1.444 1.555 1.667 1.778
-316 -317 -318 -319 -320
0.840 0.902 0.965 1.027 1.088
0.860 0.922 0.985 1.047 1.112
21.34 22.91 24.51 26.09 27.64
21.84 23.42 25.02 26.59 28.24
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.1153 0.1221 0.1289 0.1357 0.1425
1.889 2.001 2.112 2.224 2.335
-321 -322 -323 -324 -325
1.150 1.213 1.275 1.338 1.460
1.174 1.237 1.299 1.362 1.490
29.21 30.81 32.39 33.99 37.08
29.82 31.42 32.99 34.59 37.85
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.1493 0.1561 0.1629 0.1697 0.1833
2.447 2.558 2.669 2.781 3.004
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 11 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -326 -327 -328 -329 -330
ID Inches min 1.585 1.710 1.835 1.957 2.082
ID Inches max 1.615 1.740 1.865 1.993 2.118
ID mm min 40.26 43.43 46.61 49.71 52.88
ID W mm Inches max min 41.02 0.205 44.20 0.205 47.37 0.205 50.62 0.205 53.80 0.205
W Inches max 0.215 0.215 0.215 0.215 0.215
W mm min 5.21 5.21 5.21 5.21 5.21
W mm max 5.46 5.46 5.46 5.46 5.46
Volume (Ref) Cubic Inches 0.1970 0.2106 0.2242 0.2378 0.2514
Volume (Ref) Cubic cm 3.228 3.451 3.674 3.897 4.120
-331 -332 -333 -334 -335
2.207 2.332 2.455 2.580 2.705
2.243 2.368 2.495 2.620 2.745
56.06 59.23 62.36 65.53 68.71
56.97 60.15 63.37 66.55 69.72
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.2650 0.2786 0.2922 0.3058 0.3194
4.343 4.565 4.788 5.011 5.234
-336 -337 -338 -339 -340
2.830 2.951 3.076 3.201 3.326
2.870 2.999 3.124 3.249 3.374
71.88 74.96 78.13 81.31 84.48
72.90 76.17 79.35 82.52 85.70
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.3330 0.3466 0.3602 0.3738 0.3874
5.457 5.680 5.903 6.125 6.348
-341 -342 -343 -344 -345
3.451 3.572 3.697 3.822 3.947
3.499 3.628 3.753 3.878 4.003
87.66 90.73 93.90 97.08 100.25
88.87 92.15 95.33 98.50 101.68
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.4010 0.4146 0.4282 0.4418 0.4554
6.571 6.796 7.017 7.240 7.463
-346 -347 -348 -349 -350
4.072 4.195 4.320 4.445 4.570
4.128 4.255 4.380 4.505 4.630
103.43 106.55 109.73 112.90 116.08
104.85 108.08 111.25 114.43 117.60
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.4690 0.4826 0.4962 0.5098 0.5234
7.686 7.908 8.131 8.354 8.577
-351 -352 -353 -354 -355
4.695 4.820 4.938 5.063 5.188
4.755 4.880 5.012 5.137 5.262
119.25 122.43 125.43 128.60 131.78
120.78 123.95 127.30 130.46 133.65
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.5370 0.5506 0.5642 0.5778 0.5914
8.800 9.023 9.246 9.468 9.691
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 12 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -356 -357 -358 -359 -360
ID ID Inches Inches min max 5.313 5.387 5.438 5.512 5.563 5.637 5.688 5.762 5.813 5.887
ID mm min 134.95 138.13 141.30 144.48 147.65
ID W mm Inches max min 136.83 0.205 140.00 0.205 143.18 0.205 146.35 0.205 149.53 0.205
W Inches max 0.215 0.215 0.215 0.215 0.215
W mm min 5.21 5.21 5.21 5.21 5.21
W mm max 5.46 5.46 5.46 5.46 5.46
Volume (Ref) Cubic Inches 0.6050 0.6186 0.6322 0.6458 0.6594
Volume (Ref) Cubic cm 9.914 10.137 10.360 10.583 10.806
-361 -362 -363 -364 -365
5.938 6.185 6.435 6.685 6.935
6.012 6.265 6.515 6.765 7.015
150.83 157.10 163.45 169.80 176.15
152.70 159.13 165.48 171.83 178.18
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.6730 0.7002 0.7274 0.7546 0.7818
11.029 11.474 11.920 12.366 12.811
-366 -367 -368 -369 -370
7.180 7.430 7.680 7.930 8.175
7.270 7.520 7.770 8.020 8.275
182.37 188.72 195.07 201.42 207.65
184.66 191.01 197.36 203.71 210.19
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.8090 0.8362 0.8634 0.8906 0.9178
13.257 13.703 14.149 14.594 15.040
-371 -372 -373 -374 -375
8.425 8.675 8.925 9.170 9.420
8.525 8.775 9.025 9.280 9.530
214.00 220.35 226.70 232.92 239.27
216.54 222.89 229.24 235.71 242.06
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.9450 0.9722 0.9994 1.0266 1.0538
15.486 15.932 16.377 16.823 17.269
-376 -377 -378 -379 -380
9.670 9.920 10.415 10.915 11.410
9.780 10.030 10.535 11.035 11.540
245.62 251.97 264.54 277.24 289.81
248.41 254.76 267.59 280.29 293.12
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
1.0811 1.1083 1.1627 1.2171 1.2715
17.716 18.162 19.053 19.945 20.836
-381 -382 -383 -384 -385
11.910 12.910 13.905 14.905 15.880
12.040 13.040 14.045 15.045 16.030
302.51 327.91 353.19 378.59 403.35
305.82 331.22 356.74 382.14 407.16
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
1.3269 1.4347 1.5435 1.6523 1.7590
21.728 23.511 25.293 27.076 28.825
--`,```,`,,,`,`,`,```,`````
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 13 of 15
Dash Number -386 -387 -388 -389 -390
ID Inches min 16.875 17.870 18.865 19.860 20.860
ID Inches max 17.035 18.040 19.045 20.050 21.050
ID mm min 428.63 453.90 479.17 504.44 529.84
ID W mm Inches max min 432.69 0.205 458.22 0.205 483.74 0.205 509.27 0.205 534.67 0.205
W Inches max 0.215 0.215 0.215 0.215 0.215
W mm min 5.21 5.21 5.21 5.21 5.21
W mm max 5.46 5.46 5.46 5.46 5.46
Volume (Ref) Cubic Inches 1.8678 1.9766 2.0854 2.1942 2.3030
Volume (Ref) Cubic cm 30.608 32.391 34.174 35.957 37.739
-391 -392 -393 -394 -395
21.855 22.835 23.830 24.825 25.820
22.055 23.045 24.050 25.055 26.060
555.12 580.01 605.26 630.56 655.83
560.20 585.34 610.87 636.40 661.92
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
2.4118 2.5190 2.6278 2.7366 2.8454
39.522 41.279 43.062 44.845 46.628
*396 THRU *424
*O-RING SIZES NOT ASSIGNED
-425
4.442
4.508
112.83
114.50
0.269
0.281
6.83
7.14
0.8863
14.524
-426 -427 -428 -429 -430
4.567 4.692 4.817 4.938 5.063
4.633 4.758 4.883 5.012 5.137
116.00 119.18 122.35 125.43 128.60
117.68 120.85 124.03 127.30 130.48
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
0.9097 0.9330 0.9563 0.9796 1.0030
14.907 15.289 15.671 16.053 16.436
-431 -432 -433 -434 -435
5.188 5.313 5.438 5.563 5.688
5.262 5.387 5.512 5.637 5.762
131.78 134.95 138.13 141.30 144.48
133.65 136.83 140.00 143.18 146.35
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
1.0263 1.0496 1.0729 1.0963 1.1196
16.818 17.200 17.582 17.965 18.347
-436 -437 -438 -439 -440
5.813 5.938 6.185 6.435 6.685
5.887 6.012 6.265 6.515 6.765
147.65 150.83 157.10 163.45 169.80
149.53 152.70 159.13 165.48 171.83
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
1.1429 1.1662 1.2129 1.2595 1.3062
18.729 19.111 19.876 20.640 21.405
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
SAE INTERNATIONAL
AS568D
Page 14 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
ID ID Inches Inches min max 6.935 7.015 7.180 7.270 7.430 7.520 7.680 7.770 7.930 8.020
ID mm min 176.15 182.37 188.72 195.07 201.42
ID W mm Inches max min 178.18 0.269 184.66 0.269 191.01 0.269 197.36 0.269 203.71 0.269
W Inches max 0.281 0.281 0.281 0.281 0.281
W mm min 6.83 6.83 6.83 6.83 6.83
W mm max 7.14 7.14 7.14 7.14 7.14
Volume (Ref) Cubic Inches 1.3528 1.3995 1.4461 1.4928 1.5394
Volume (Ref) Cubic cm 22.168 22.934 23.697 24.463 25.226
-446 -447 -448 -449 -450
8.420 8.920 9.420 9.920 10.415
8.530 9.030 9.530 10.030 10.535
213.87 226.57 239.27 251.97 264.54
216.66 229.36 242.06 254.76 267.59
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
1.6327 1.7260 1.8193 1.9126 2.0059
26.755 28.284 29.813 31.342 32.871
-451 -452 -453 -454 -455
10.915 11.415 11.915 12.415 12.915
11.035 11.535 12.035 12.535 13.035
277.24 289.94 302.64 315.34 328.04
280.29 292.99 305.69 318.39 331.09
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
2.0992 2.1925 2.2858 2.3791 2.4724
34.400 35.929 37.458 38.987 40.515
-456 -457 -458 -459 -460
13.405 13.905 14.405 14.905 15.405
13.545 14.045 14.545 15.045 15.545
340.49 353.19 365.89 378.59 391.29
344.04 356.74 369.44 382.14 394.84
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
2.5657 2.6590 2.7523 2.8456 2.9389
42.044 43.573 45.102 46.631 48.160
-461 -462 -463 -464 -465
15.880 16.380 16.875 17.370 17.870
16.030 16.530 17.035 17.540 18.040
403.35 416.05 428.63 441.20 453.90
407.16 419.86 432.69 445.52 458.22
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
3.0285 3.1218 3.2151 3.3084 3.4017
49.628 51.157 52.686 54.215 55.744
-466 -467 -468 -469 -470
18.370 18.865 19.365 19.860 20.860
18.540 19.045 19.545 20.050 21.050
466.60 479.17 491.87 504.44 529.84
470.92 483.74 496.44 509.27 534.67
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
3.4950 3.5883 3.6816 3.7749 3.9615
57.273 58.802 60.331 61.860 64.917
Dash Number -441 -442 -443 -444 -445
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 15 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -471 -472 -473 -474 -475
ID ID Inches Inches min max 21.855 22.055 22.835 23.045 23.830 24.050 24.825 25.055 25.820 26.060
ID mm min 555.12 580.01 605.28 630.56 655.83
ID W mm Inches max min 560.20 0.269 585.34 0.269 610.87 0.269 636.40 0.269 661.92 0.269
W Inches max 0.281 0.281 0.281 0.281 0.281
W mm min 6.83 6.83 6.83 6.83 6.83
W mm max 7.14 7.14 7.14 7.14 7.14
Volume (Ref) Cubic Inches 4.1481 4.3319 4.5184 4.7050 4.8916
Volume (Ref) Cubic cm 67.975 70.987 74.043 77.101 80.159
TABLE 2 - AEROSPACE SIZE STANDARDS FOR STRAIGHT THREAD TUBE FITTING BOSS GASKETS
Dash Number -901 -902 -903 -904 -905
Tube Size (Nom) Inches 0.094 0.125 0.188 0.250 0.313
Tube Size (Nom) mm 2.38 3.18 4.76 6.35 7.94
ID Inches min 0.180 0.234 0.296 0.346 0.409
ID Inches max 0.190 0.244 0.306 0.356 0.419
ID mm min 4.57 5.94 7.52 8.79 10.39
D mm max 4.83 6.20 7.77 9.04 10.64
W Inches min 0.053 0.061 0.061 0.069 0.069
W Inches max 0.059 0.067 0.067 0.075 0.075
W mm min 1.35 1.55 1.55 1.75 1.75
W mm max 1.50 1.70 1.70 1.91 1.91
Volume (Ref) Cubic Inches 0.0019 0.0031 0.0037 0.0054 0.0062
Volume (Ref) Cubic cm 0.031 0.051 0.061 0.088 0.102
-906 -907 -908 -909 -910
0.375 0.438 0.500 0.563 0.625
9.53 11.11 12.70 14.29 15.88
0.463 0.523 0.635 0.697 0.746
0.473 0.537 0.653 0.715 0.764
11.76 13.28 16.13 17.70 18.95
12.01 13.64 16.59 18.16 19.41
0.075 0.079 0.084 0.094 0.094
0.081 0.085 0.090 0.100 0.100
1.90 2.01 2.13 2.39 2.39
2.06 2.16 2.29 2.54 2.54
0.0082 0.0102 0.0137 0.0186 0.0198
0.134 0.167 0.225 0.305 0.324
-911 -912 -913 -914 -916
0.688 0.750 0.183 0.875 1.000
17.46 19.05 20.64 22.23 25.40
0.854 0.915 0.976 1.037 1.161
0.872 0.933 0.996 1.057 1.181
21.69 23.24 24.79 26.34 29.49
22.15 23.70 25.30 26.85 30.00
0.112 0.112 0.112 0.112 0.112
0.120 0.120 0.120 0.120 0.120
2.85 2.85 2.85 2.85 2.85
3.05 3.05 3.05 3.05 3.05
0.0325 0.0345 0.0366 0.0386 0.0427
0.533 0.565 0.600 0.633 0.700
-918 -920 -924 -928 -932
1.125 1.250 1.500 1.750 2.000
28.58 31.75 38.10 44.45 50.80
1.343 1.461 1.706 2.072 2.319
1.367 1.489 1.734 2.108 2.356
34.11 37.11 43.33 52.63 58.90
34.72 37.82 44.04 53.54 59.84
0.112 0.114 0.114 0.114 0.114
0.120 0.122 0.122 0.122 0.122
2.85 2.90 2.90 2.90 2.90
3.05 3.10 3.10 3.10 3.10
0.0488 0.0547 0.0631 0.0759 0.0843
0.800 0.896 1.034 1.244 1.381
PREPARED BY SAE SUBCOMMITTEE A-6C2, SEALS OF COMMITTEE A-6, AEROSPACE ACTUATION, CONTROL AND FLUID POWER SYSTEMS
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
AEROSPACE STANDARD
Issued Revised
REV. D 1971-07 2014-03
Superseding AS568C
Aerospace Size Standard for O-rings RATIONALE The drawing has been revised to eliminate the parting line projection shown in earlier issues since it is not applicable to an O-ring size standard. 1. SCOPE 1.1
Purpose
This SAE Aerospace Standard (AS) specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. The dimensions and tolerances specified in this standard are suitable for any elastomeric material provided that suitable tooling is available. 1.2
Application
1.2.1
This standard is intended to be used in the preparation of Company, Military, or other Standard Drawings for O-rings. Each dash number, which should be appended to an appropriate Drawing or Standard number, identifies one nominal size O-ring only.
1.2.2
No attempt is made in this AS to indicate which of the O-ring sizes listed under this system should be included in any particular Standard Drawing. Its only purpose is to standardize O-ring sizes and dimensional tolerances and the means of identifying them dimensionally.
2. REFERENCES There are no referenced publications specified herein. 3. NOTES --`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
3.1
In Table 1, the dash numbers are divided into groups of one hundred, and within each group are sequential and non-significant. Each hundred group, however, identifies the cross section size of the O-rings within the group. For example, all 0.070 inch (1.78 mm) and smaller O-ring cross sections fall into the group of -001 thru -099. The 0.103 inch (2.62 mm) cross section rings fall into the group of -100 thru -199, and so on.
__________________________________________________________________________________________________________________________________________ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the .” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright © 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER:
Provided by IHS SAEorWEB ADDRESS: No reproduction networking permitted without license from IHS
SAE values your input. To provide Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) on this Technical Report, please visit Fax: 724-776-0790 http://www.sae.org/technical/standards/AS568D Email: [email protected] Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo http://www.sae.org Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 2 of 15
3.2
Table 2, using the 900 series dash numbers, lists all of the presently standardized straight thread tube fitting boss gaskets. This series has traditionally utilized the significant dash numbering system, wherein the dash number designates the tube size in 16th’s of an inch. This practice is also followed here, with the exception of the -901, which is intended for a 0.0938 inch (2.38 mm) nominal OD (outside diameter) tube, the 0.0625 inch (1.59 mm) OD tube not being in common aircraft use.
3.3
In the interest of standardization, it is requested that companies or agencies do not use the dash numbers in Table 1 to which sizes have not been assigned. Sizes not assigned are indicated by an asterisk (*). Anyone feeling that any special size not now shown is widely enough used to justify standardization should direct such a request to SAE A-6 Committee for coordination.
3.4
Figure 1 illustrates that all diameters of the cross-section should be equal.
FIGURE 1 - O-RING DIMENSIONS: WIDTH (W) AND INSIDE DIAMETER (D) 3.5
A change bar (l) located in the left margin is for the convenience of the in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 3 of 15
Dash Number -001 -002 -003 -004 -005
ID Inches min 0.025 0.038 0.052 0.065 0.096
ID Inches max 0.033 0.046 0.060 0.075 0.106
ID mm min 0.64 0.97 1.32 1.65 2.44
ID mm max 0.84 1.17 1.52 1.91 2.69
W Inches min 0.037 0.047 0.057 0.067 0.067
W Inches max 0.043 0.053 0.063 0.073 0.073
W mm min 0.94 1.19 1.45 1.70 1.70
W mm max 1.09 1.35 1.60 1.85 1.85
Volume (Ref) Cubic Inches 0.0003 0.0006 0.0010 0.0017 0.0021
Volume (Ref) Cubic cm 0.005 0.010 0.016 0.028 0.034
-006 -007 -008 -009 -010
0.109 0.140 0.171 0.203 0.234
0.119 0.150 0.181 0.213 0.244
2.77 3.56 4.34 5.16 5.94
3.02 3.81 4.60 5.41 6.20
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0022 0.0026 0.0030 0.0034 0.0037
0.036 0.043 0.049 0.056 0.061
-011 -012 -013 -014 -015
0.296 0.359 0.421 0.484 0.544
0.306 0.369 0.431 0.494 0.558
7.52 9.12 10.69 12.29 13.82
7.77 9.37 10.95 12.55 14.17
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0045 0.0052 0.0060 0.0068 0.0075
0.074 0.085 0.098 0.111 0.123
-016 -017 -018 -019 -020
0.605 0.667 0.730 0.792 0.855
0.623 0.685 0.748 0.810 0.873
15.37 16.94 18.54 20.12 21.72
15.82 17.40 19.00 20.57 22.17
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0083 0.0090 0.0098 0.0105 0.0113
0.136 0.147 0.161 0.172 0.185
-021 -022 -023 -024 -025
0.917 0.979 1.041 1.104 1.165
0.935 0.999 1.061 1.124 1.187
23.29 24.87 26.44 28.04 29.59
23.75 25.37 26.95 28.55 30.15
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0120 0.0128 0.0136 0.0143 0.0151
0.197 0.210 0.223 0.234 0.247
-026 -027 -028 -029 -030
1.228 1.290 1.351 1.476 1.601
1.250 1.312 1.377 1.502 1.627
31.19 32.77 34.32 37.49 40.67
31.75 33.32 34.98 38.15 41.33
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0158 0.0166 0.0173 0.0188 0.0204
0.259 0.272 0.283 0.308 0.334
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS
SAE INTERNATIONAL
AS568D
Page 4 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
ID Inches max 1.754 1.879 2.007 2.132 2.257
ID mm min 43.79 46.96 50.06 53.24 56.41
ID mm max 44.55 47.73 50.98 54.15 57.33
W Inches min 0.067 0.067 0.067 0.067 0.067
W Inches max 0.073 0.073 0.073 0.073 0.073
W mm min 1.70 1.70 1.70 1.70 1.70
W mm max 1.85 1.85 1.85 1.85 1.85
Volume (Ref) Cubic Inches 0.0219 0.0234 0.0249 0.0264 0.0279
Volume (Ref) Cubic cm 0.359 0.383 0.408 0.433 0.457
-036 -037 -038 -039 -040
2.346 2.471 2.594 2.719 2.844
2.382 2.507 2.634 2.759 2.884
59.59 62.76 65.89 69.06 72.24
60.50 63.68 66.90 70.08 73.25
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0294 0.0309 0.0325 0.0340 0.0355
0.482 0.506 0.533 0.557 0.582
-041 -042 -043 -044 -045
2.965 3.215 3.465 3.712 3.962
3.013 3.263 3.513 3.766 4.016
75.31 81.66 88.01 94.28 100.63
76.53 82.88 89.23 95.66 102.01
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0370 0.0400 0.0430 0.0461 0.0491
0.606 0.655 0.705 0.755 0.805
-046 -047 -048 -049 -050
4.209 4.459 4.709 4.952 5.202
4.269 4.519 4.769 5.026 5.276
106.91 113.26 119.61 125.78 132.13
108.43 114.78 121.13 127.66 134.01
0.067 0.067 0.067 0.067 0.067
0.073 0.073 0.073 0.073 0.073
1.70 1.70 1.70 1.70 1.70
1.85 1.85 1.85 1.85 1.85
0.0521 0.0551 0.0581 0.0612 0.0642
0.854 0.903 0.952 1.003 1.052
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Dash Number -031 -032 -033 -034 -035
ID Inches min 1.724 1.849 1.971 2.096 2.221
*051 THRU *101 -102 -103 -104 -105
*O-RING SIZES NOT ASSIGNED 0.044 0.076 0.107 0.138
Provided by IHS No reproduction or networking permitted without license from IHS
0.054 0.086 0.117 0.148
1.12 1.93 2.72 3.51
1.37 2.18 2.97 3.76
0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69
0.0040 0.0048 0.0056 0.0064
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
0.066 0.079 0.092 0.105
SAE INTERNATIONAL
AS568D
Page 5 of 15
Dash Number -106 -107 -108 -109 -110
ID Inches min 0.169 0.201 0.232 0.294 0.357
ID Inches max 0.179 0.211 0.242 0.304 0.367
ID mm min 4.29 5.11 5.89 7.47 9.07
ID mm max 4.55 5.36 6.15 7.72 9.32
W Inches min 0.100 0.100 0.100 0.100 0.100
W Inches max 0.106 0.106 0.106 0.106 0.106
W mm min 2.54 2.54 2.54 2.54 2.54
W mm max 2.69 2.69 2.69 2.69 2.69
Volume (Ref) Cubic Inches 0.0073 0.0081 0.0089 0.0105 0.0122
Volume (Ref) Cubic cm 0.120 0.133 0.146 0.172 0.200
-111 -112 -113 -114 -115
0.419 0.482 0.542 0.603 0.665
0.429 0.492 0.556 0.621 0.683
10.64 12.24 13.77 15.32 16.89
10.90 12.50 14.12 15.77 17.35
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0138 0.0154 0.0171 0.0187 0.0203
0.226 0.252 0.280 0.306 0.333
-116 -117 -118 -119 -120
0.728 0.789 0.852 0.914 0.977
0.746 0.809 0.872 0.934 0.997
18.49 20.04 21.64 23.22 24.82
18.95 20.55 22.15 23.72 25.32
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0220 0.0236 0.0253 0.0269 0.0285
0.361 0.387 0.415 0.441 0.467
-121 -122 -123 -124 -125
1.039 1.102 1.162 1.225 1.287
1.059 1.122 1.186 1.249 1.311
26.39 27.99 29.51 31.12 32.69
26.90 28.50 30.12 31.72 33.30
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0302 0.0318 0.0334 0.0351 0.0367
0.495 0.521 0.547 0.575 0.601
-126 -127 -128 -129 -130
1.350 1.412 1.475 1.534 1.597
1.374 1.436 1.499 1.564 1.627
34.29 35.86 37.46 38.96 40.56
34.90 36.47 38.07 39.73 41.33
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0383 0.0400 0.0416 0.0432 0.0449
0.628 0.655 0.682 0.708 0.736
-131 -132 -133 -134 -135
1.659 1.722 1.784 1.847 1.908
1.689 1.752 1.814 1.877 1.942
42.14 43.74 45.31 46.91 48.46
42.90 44.50 46.08 47.68 49.33
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0465 0.0482 0.0498 0.0514 0.0531
0.762 0.790 0.816 0.842 0.870
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
SAE INTERNATIONAL
AS568D
Page 6 of 15
Dash Number -136 -137 -138 -139 -140
ID Inches min 1.970 2.033 2.095 2.158 2.220
ID Inches max 2.004 2.067 2.129 2.192 2.254
ID mm min 50.04 51.64 53.21 54.81 56.39
ID mm max 50.90 52.50 54.08 55.68 57.25
W Inches min 0.100 0.100 0.100 0.100 0.100
W Inches max 0.106 0.106 0.106 0.106 0.106
W mm min 2.54 2.54 2.54 2.54 2.54
W mm max 2.69 2.69 2.69 2.69 2.69
Volume (Ref) Cubic Inches 0.0547 0.0564 0.0580 0.0596 0.0613
Volume (Ref) Cubic cm 0.896 0.924 0.950 0.977 1.005
-141 -142 -143 -144 -145
2.280 2.342 2.405 2.467 2.530
2.320 2.382 2.445 2.507 2.570
57.91 59.49 61.09 62.66 64.26
58.93 60.50 62.10 63.68 65.28
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0629 0.0645 0.0662 0.0678 0.0694
1.031 1.057 1.085 1.111 1.137
-146 -147 -148 -149 -150
2.592 2.653 2.715 2.778 2.840
2.632 2.697 2.759 2.822 2.884
65.84 67.39 68.96 70.56 72.14
66.85 68.50 70.08 71.68 73.25
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0711 0.0727 0.0743 0.0760 0.0776
1.165 1.191 1.218 1.245 1.272
-151 -152 -153 -154 -155
2.963 3.213 3.463 3.709 3.959
3.011 3.261 3.511 3.765 4.015
75.26 81.61 87.96 94.21 100.56
76.48 82.83 89.18 95.63 101.98
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.0809 0.0874 0.0940 0.1005 0.1071
1.326 1.432 1.540 1.647 1.755
-156 -157 -158 -159 -160
4.207 4.457 4.707 4.952 5.202
4.267 4.517 4.767 5.022 5.272
106.86 113.21 119.56 125.78 132.13
108.38 114.73 121.08 127.56 133.91
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.1136 0.1202 0.1267 0.1332 1.1398
1.862 1.970 2.076 2.183 2.291
-161 -162 -163 -164 -165
5.452 5.702 5.952 6.197 6.447
5.522 5.772 6.022 6.277 6.527
138.48 144.83 151.18 157.40 163.75
140.26 146.61 152.96 159.44 165.79
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.1463 0.1529 0.1594 0.1660 0.1725
2.397 2.506 2.612 2.720 2.827
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
SAE INTERNATIONAL
AS568D
Page 7 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -166 -167 -168 -169 -170
ID Inches min 6.697 6.947 7.192 7.442 7.692
ID Inches max 6.777 7.027 7.282 7.532 7.782
ID mm min 170.10 176.45 182.68 189.03 195.38
ID mm max 172.14 178.49 184.96 191.31 197.66
W Inches min 0.100 0.100 0.100 0.100 0.100
W Inches max 0.106 0.106 0.106 0.106 0.106
W mm min 2.54 2.54 2.54 2.54 2.54
W mm max 2.69 2.69 2.69 2.69 2.69
Volume (Ref) Cubic Inches 0.1790 0.1856 0.1921 0.1987 0.2052
Volume (Ref) Cubic cm 2.933 3.041 3.148 3.256 3.363
-171 -172 -173 -174 -175
7.942 8.187 8.437 8.687 8.937
8.032 8.287 8.537 8.787 9.037
201.73 207.95 214.30 220.65 227.00
204.01 210.49 216.84 223.19 229.54
0.100 0.100 0.100 0.100 0.100
0.106 0.106 0.106 0.106 0.106
2.54 2.54 2.54 2.54 2.54
2.69 2.69 2.69 2.69 2.69
0.2118 0.2183 0.2249 0.2314 0.2379
3.471 3.577 3.685 3.792 3.898
-176 -177 -178
9.182 9.432 9.682
9.292 9.542 9.792
233.22 239.57 245.92
236.02 242.37 248.72
0.100 0.100 0.100
0.106 0.106 0.106
2.54 2.54 2.54
2.69 2.69 2.69
0.2445 0.2510 0.2576
4.007 4.113 4.221
*O-RING SIZES NOT ASSIGNED
-201 -202 -203 -204 -205
0.166 0.229 0.291 0.354 0.416
0.176 0.239 0.301 0.364 0.426
4.22 5.82 7.39 8.99 10.57
4.47 6.07 7.65 9.25 10.82
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.0148 0.0178 0.0207 0.0237 0.0267
0.243 0.292 0.339 0.388 0.438
-206 -207 -208 -209 -210
0.479 0.539 0.600 0.662 0.724
0.489 0.553 0.618 0.680 0.744
12.17 13.69 15.24 16.81 18.39
12.42 14.05 15.70 17.27 18.90
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.0297 0.0327 0.0357 0.0386 0.0416
0.487 0.536 0.586 0.633 0.682
-211 -212 -213 -214 -215
0.786 0.849 0.911 0.974 1.036
0.806 0.869 0.931 0.994 1.056
19.96 21.56 23.14 24.74 26.31
20.47 22.07 23.65 25.25 26.82
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.0446 0.0476 0.0505 0.0535 0.0565
0.731 0.780 0.828 0.877 0.926
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
*179 THRU *200
SAE INTERNATIONAL
AS568D
Page 8 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
ID Inches max 1.121 1.183 1.246 1.308 1.371
ID mm min 27.86 29.44 31.04 32.61 34.21
ID mm max 28.47 30.05 31.65 33.22 34.82
W Inches min 0.135 0.135 0.135 0.135 0.135
W Inches max 0.143 0.143 0.143 0.143 0.143
W mm min 3.43 3.43 3.43 3.43 3.43
W mm max 3.63 3.63 3.63 3.63 3.63
Volume (Ref) Cubic Inches 0.0595 0.0625 0.0655 0.0684 0.0714
Volume (Ref) Cubic cm 0.975 1.024 1.073 1.121 1.170
-221 -222 -223 -224 -225
1.409 1.469 1.594 1.719 1.841
1.433 1.499 1.624 1.749 1.877
35.79 37.31 40.49 43.66 46.76
36.40 38.07 41.25 44.42 47.68
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.0744 0.0774 0.0833 0.0893 0.0952
1.219 1.268 1.365 1.463 1.560
-226 -227 -228 -229 -230
1.966 2.091 2.214 2.339 2.464
2.002 2.127 2.254 2.379 2.504
49.94 53.11 56.24 59.41 62.59
50.85 54.03 57.25 60.43 63.60
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.1012 0.1072 0.1131 0.1191 0.1250
1.658 1.757 1.853 1.952 2.048
-231 -232 -233 -234 -235
2.589 2.710 2.835 2.960 3.085
2.629 2.758 2.883 3.008 3.133
65.76 68.83 72.01 75.18 78.36
66.78 70.05 73.23 76.40 79.58
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.1310 0.1370 0.1429 0.1489 0.1548
2.147 2.245 2.342 2.440 2.537
-236 -237 -238 -239 -240
3.210 3.335 3.460 3.581 3.706
3.258 3.383 3.508 3.637 3.762
81.53 84.71 87.88 90.96 94.13
82.75 85.93 89.10 92.38 95.55
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.1608 0.1668 0.1727 0.1787 0.1846
2.635 2.733 2.830 2.928 3.025
-241 -242 -243 -244 -245
3.831 3.956 4.081 4.204 4.329
3.887 4.012 4.137 4.264 4.389
97.31 100.48 103.66 106.76 109.96
98.73 101.90 105.08 108.31 111.48
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.1906 0.1966 0.2025 0.2085 0.2144
3.123 3.222 3.318 3.417 3.513
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Dash Number -216 -217 -218 -219 -220
ID Inches min 1.097 1.159 1.222 1.284 1.347
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 9 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
ID Inches max 4.514 4.639 4.764 4.894 5.019
ID mm min 113.13 116.31 119.48 122.53 125.70
ID W mm Inches max min 114.66 0.135 117.83 0.135 121.01 0.135 124.31 0.135 127.48 0.135
W Inches max 0.143 0.143 0.143 0.143 0.143
W mm min 3.43 3.43 3.43 3.43 3.43
W mm max 3.63 3.63 3.63 3.63 3.63
Volume (Ref) Cubic Inches 0.2204 0.2263 0.2323 0.2383 0.2442
Volume (Ref) Cubic cm 3.612 3.708 3.807 3.905 4.002
-251 -252 -253 -254 -255
5.074 5.199 5.324 5.449 5.574
5.144 5.269 5.394 5.519 5.644
128.88 132.05 135.23 138.40 141.58
130.66 133.83 137.01 140.18 143.36
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.2502 0.2561 0.2621 0.2681 0.2740
4.100 4.197 4.295 4.393 4.490
-256 -257 -258 -259 -260
5.699 5.824 5.949 6.194 6.444
5.769 5.894 6.019 6.274 6.524
144.75 147.93 151.10 157.33 163.68
146.53 149.71 152.88 159.36 165.71
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.2800 0.2859 0.2919 0.3038 0.3157
4.588 4.685 4.783 4.978 5.173
-261 -262 -263 -264 -265
6.694 6.944 7.189 7.439 7.689
6.774 7.024 7.279 7.529 7.779
170.03 176.38 182.60 188.95 195.30
172.06 178.41 184.89 191.24 197.59
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.3277 0.3396 0.3515 0.3634 0.3753
5.370 5.565 5.760 5.955 6.150
-266 -267 -268 -269 -270
7.939 8.184 8.434 8.684 8.934
8.029 8.284 8.534 8.784 9.034
201.65 207.87 214.22 220.57 226.92
203.94 210.41 216.76 223.11 229.46
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.3872 0.3992 0.4111 0.4230 0.4349
6.345 6.542 6.737 6.932 7.127
-271 -272 -273 -274 -275
9.179 9.429 9.679 9.929 10.429
9.289 9.539 9.789 10.039 10.539
233.15 239.50 245.85 252.20 264.90
235.94 242.29 248.64 254.99 267.69
0.135 0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63 3.63
0.4468 0.4588 0.4707 0.4826 0.5064
7.322 7.518 7.713 7.908 8.298
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Dash Number -246 -247 -248 -249 -250
ID Inches min 4.454 4.579 4.704 4.824 4.949
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 10 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -276 -277 -278 -279 -280
ID Inches min 10.919 11.419 11.919 12.919 13.919
ID Inches max 11.049 11.549 12.049 13.049 14.049
ID mm min 277.34 290.04 302.74 328.14 353.54
ID W mm Inches max min 280.64 0.135 293.34 0.135 306.04 0.135 331.44 0.135 356.84 0.135
W Inches max 0.143 0.143 0.143 0.143 0.143
W mm min 3.43 3.43 3.43 3.43 3.43
W mm max 3.63 3.63 3.63 3.63 3.63
Volume (Ref) Cubic Inches 0.5303 0.5541 0.5779 0.6256 0.6733
Volume (Ref) Cubic cm 8.690 9.080 9.470 10.252 11.033
-281 -282 -283 -284
14.919 15.880 16.875 17.870
15.049 16.030 17.035 18.040
378.94 403.35 428.63 453.90
382.24 407.16 432.69 458.22
0.135 0.135 0.135 0.135
0.143 0.143 0.143 0.143
3.43 3.43 3.43 3.43
3.63 3.63 3.63 3.63
0.7210 0.7672 0.8149 0.8626
11.815 12.572 13.354 14.136
*285 THRU *308
*O-RING SIZES NOT ASSIGNED
-309 -310
0.407 0.470
0.417 0.480
10.34 11.94
10.59 12.19
0.205 0.205
0.215 0.215
5.21 5.21
5.46 5.46
0.0677 0.0745
1.109 1.221
-311 -312 -313 -314 -315
0.530 0.591 0.653 0.715 0.777
0.544 0.609 0.671 0.735 0.797
13.46 15.01 16.59 18.16 19.74
13.82 15.47 17.04 18.67 20.24
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.0813 0.0881 0.0949 0.1017 0.1085
1.332 1.444 1.555 1.667 1.778
-316 -317 -318 -319 -320
0.840 0.902 0.965 1.027 1.088
0.860 0.922 0.985 1.047 1.112
21.34 22.91 24.51 26.09 27.64
21.84 23.42 25.02 26.59 28.24
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.1153 0.1221 0.1289 0.1357 0.1425
1.889 2.001 2.112 2.224 2.335
-321 -322 -323 -324 -325
1.150 1.213 1.275 1.338 1.460
1.174 1.237 1.299 1.362 1.490
29.21 30.81 32.39 33.99 37.08
29.82 31.42 32.99 34.59 37.85
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.1493 0.1561 0.1629 0.1697 0.1833
2.447 2.558 2.669 2.781 3.004
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 11 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -326 -327 -328 -329 -330
ID Inches min 1.585 1.710 1.835 1.957 2.082
ID Inches max 1.615 1.740 1.865 1.993 2.118
ID mm min 40.26 43.43 46.61 49.71 52.88
ID W mm Inches max min 41.02 0.205 44.20 0.205 47.37 0.205 50.62 0.205 53.80 0.205
W Inches max 0.215 0.215 0.215 0.215 0.215
W mm min 5.21 5.21 5.21 5.21 5.21
W mm max 5.46 5.46 5.46 5.46 5.46
Volume (Ref) Cubic Inches 0.1970 0.2106 0.2242 0.2378 0.2514
Volume (Ref) Cubic cm 3.228 3.451 3.674 3.897 4.120
-331 -332 -333 -334 -335
2.207 2.332 2.455 2.580 2.705
2.243 2.368 2.495 2.620 2.745
56.06 59.23 62.36 65.53 68.71
56.97 60.15 63.37 66.55 69.72
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.2650 0.2786 0.2922 0.3058 0.3194
4.343 4.565 4.788 5.011 5.234
-336 -337 -338 -339 -340
2.830 2.951 3.076 3.201 3.326
2.870 2.999 3.124 3.249 3.374
71.88 74.96 78.13 81.31 84.48
72.90 76.17 79.35 82.52 85.70
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.3330 0.3466 0.3602 0.3738 0.3874
5.457 5.680 5.903 6.125 6.348
-341 -342 -343 -344 -345
3.451 3.572 3.697 3.822 3.947
3.499 3.628 3.753 3.878 4.003
87.66 90.73 93.90 97.08 100.25
88.87 92.15 95.33 98.50 101.68
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.4010 0.4146 0.4282 0.4418 0.4554
6.571 6.796 7.017 7.240 7.463
-346 -347 -348 -349 -350
4.072 4.195 4.320 4.445 4.570
4.128 4.255 4.380 4.505 4.630
103.43 106.55 109.73 112.90 116.08
104.85 108.08 111.25 114.43 117.60
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.4690 0.4826 0.4962 0.5098 0.5234
7.686 7.908 8.131 8.354 8.577
-351 -352 -353 -354 -355
4.695 4.820 4.938 5.063 5.188
4.755 4.880 5.012 5.137 5.262
119.25 122.43 125.43 128.60 131.78
120.78 123.95 127.30 130.46 133.65
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.5370 0.5506 0.5642 0.5778 0.5914
8.800 9.023 9.246 9.468 9.691
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 12 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -356 -357 -358 -359 -360
ID ID Inches Inches min max 5.313 5.387 5.438 5.512 5.563 5.637 5.688 5.762 5.813 5.887
ID mm min 134.95 138.13 141.30 144.48 147.65
ID W mm Inches max min 136.83 0.205 140.00 0.205 143.18 0.205 146.35 0.205 149.53 0.205
W Inches max 0.215 0.215 0.215 0.215 0.215
W mm min 5.21 5.21 5.21 5.21 5.21
W mm max 5.46 5.46 5.46 5.46 5.46
Volume (Ref) Cubic Inches 0.6050 0.6186 0.6322 0.6458 0.6594
Volume (Ref) Cubic cm 9.914 10.137 10.360 10.583 10.806
-361 -362 -363 -364 -365
5.938 6.185 6.435 6.685 6.935
6.012 6.265 6.515 6.765 7.015
150.83 157.10 163.45 169.80 176.15
152.70 159.13 165.48 171.83 178.18
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.6730 0.7002 0.7274 0.7546 0.7818
11.029 11.474 11.920 12.366 12.811
-366 -367 -368 -369 -370
7.180 7.430 7.680 7.930 8.175
7.270 7.520 7.770 8.020 8.275
182.37 188.72 195.07 201.42 207.65
184.66 191.01 197.36 203.71 210.19
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.8090 0.8362 0.8634 0.8906 0.9178
13.257 13.703 14.149 14.594 15.040
-371 -372 -373 -374 -375
8.425 8.675 8.925 9.170 9.420
8.525 8.775 9.025 9.280 9.530
214.00 220.35 226.70 232.92 239.27
216.54 222.89 229.24 235.71 242.06
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
0.9450 0.9722 0.9994 1.0266 1.0538
15.486 15.932 16.377 16.823 17.269
-376 -377 -378 -379 -380
9.670 9.920 10.415 10.915 11.410
9.780 10.030 10.535 11.035 11.540
245.62 251.97 264.54 277.24 289.81
248.41 254.76 267.59 280.29 293.12
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
1.0811 1.1083 1.1627 1.2171 1.2715
17.716 18.162 19.053 19.945 20.836
-381 -382 -383 -384 -385
11.910 12.910 13.905 14.905 15.880
12.040 13.040 14.045 15.045 16.030
302.51 327.91 353.19 378.59 403.35
305.82 331.22 356.74 382.14 407.16
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
1.3269 1.4347 1.5435 1.6523 1.7590
21.728 23.511 25.293 27.076 28.825
--`,```,`,,,`,`,`,```,`````
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 13 of 15
Dash Number -386 -387 -388 -389 -390
ID Inches min 16.875 17.870 18.865 19.860 20.860
ID Inches max 17.035 18.040 19.045 20.050 21.050
ID mm min 428.63 453.90 479.17 504.44 529.84
ID W mm Inches max min 432.69 0.205 458.22 0.205 483.74 0.205 509.27 0.205 534.67 0.205
W Inches max 0.215 0.215 0.215 0.215 0.215
W mm min 5.21 5.21 5.21 5.21 5.21
W mm max 5.46 5.46 5.46 5.46 5.46
Volume (Ref) Cubic Inches 1.8678 1.9766 2.0854 2.1942 2.3030
Volume (Ref) Cubic cm 30.608 32.391 34.174 35.957 37.739
-391 -392 -393 -394 -395
21.855 22.835 23.830 24.825 25.820
22.055 23.045 24.050 25.055 26.060
555.12 580.01 605.26 630.56 655.83
560.20 585.34 610.87 636.40 661.92
0.205 0.205 0.205 0.205 0.205
0.215 0.215 0.215 0.215 0.215
5.21 5.21 5.21 5.21 5.21
5.46 5.46 5.46 5.46 5.46
2.4118 2.5190 2.6278 2.7366 2.8454
39.522 41.279 43.062 44.845 46.628
*396 THRU *424
*O-RING SIZES NOT ASSIGNED
-425
4.442
4.508
112.83
114.50
0.269
0.281
6.83
7.14
0.8863
14.524
-426 -427 -428 -429 -430
4.567 4.692 4.817 4.938 5.063
4.633 4.758 4.883 5.012 5.137
116.00 119.18 122.35 125.43 128.60
117.68 120.85 124.03 127.30 130.48
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
0.9097 0.9330 0.9563 0.9796 1.0030
14.907 15.289 15.671 16.053 16.436
-431 -432 -433 -434 -435
5.188 5.313 5.438 5.563 5.688
5.262 5.387 5.512 5.637 5.762
131.78 134.95 138.13 141.30 144.48
133.65 136.83 140.00 143.18 146.35
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
1.0263 1.0496 1.0729 1.0963 1.1196
16.818 17.200 17.582 17.965 18.347
-436 -437 -438 -439 -440
5.813 5.938 6.185 6.435 6.685
5.887 6.012 6.265 6.515 6.765
147.65 150.83 157.10 163.45 169.80
149.53 152.70 159.13 165.48 171.83
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
1.1429 1.1662 1.2129 1.2595 1.3062
18.729 19.111 19.876 20.640 21.405
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
SAE INTERNATIONAL
AS568D
Page 14 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
ID ID Inches Inches min max 6.935 7.015 7.180 7.270 7.430 7.520 7.680 7.770 7.930 8.020
ID mm min 176.15 182.37 188.72 195.07 201.42
ID W mm Inches max min 178.18 0.269 184.66 0.269 191.01 0.269 197.36 0.269 203.71 0.269
W Inches max 0.281 0.281 0.281 0.281 0.281
W mm min 6.83 6.83 6.83 6.83 6.83
W mm max 7.14 7.14 7.14 7.14 7.14
Volume (Ref) Cubic Inches 1.3528 1.3995 1.4461 1.4928 1.5394
Volume (Ref) Cubic cm 22.168 22.934 23.697 24.463 25.226
-446 -447 -448 -449 -450
8.420 8.920 9.420 9.920 10.415
8.530 9.030 9.530 10.030 10.535
213.87 226.57 239.27 251.97 264.54
216.66 229.36 242.06 254.76 267.59
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
1.6327 1.7260 1.8193 1.9126 2.0059
26.755 28.284 29.813 31.342 32.871
-451 -452 -453 -454 -455
10.915 11.415 11.915 12.415 12.915
11.035 11.535 12.035 12.535 13.035
277.24 289.94 302.64 315.34 328.04
280.29 292.99 305.69 318.39 331.09
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
2.0992 2.1925 2.2858 2.3791 2.4724
34.400 35.929 37.458 38.987 40.515
-456 -457 -458 -459 -460
13.405 13.905 14.405 14.905 15.405
13.545 14.045 14.545 15.045 15.545
340.49 353.19 365.89 378.59 391.29
344.04 356.74 369.44 382.14 394.84
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
2.5657 2.6590 2.7523 2.8456 2.9389
42.044 43.573 45.102 46.631 48.160
-461 -462 -463 -464 -465
15.880 16.380 16.875 17.370 17.870
16.030 16.530 17.035 17.540 18.040
403.35 416.05 428.63 441.20 453.90
407.16 419.86 432.69 445.52 458.22
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
3.0285 3.1218 3.2151 3.3084 3.4017
49.628 51.157 52.686 54.215 55.744
-466 -467 -468 -469 -470
18.370 18.865 19.365 19.860 20.860
18.540 19.045 19.545 20.050 21.050
466.60 479.17 491.87 504.44 529.84
470.92 483.74 496.44 509.27 534.67
0.269 0.269 0.269 0.269 0.269
0.281 0.281 0.281 0.281 0.281
6.83 6.83 6.83 6.83 6.83
7.14 7.14 7.14 7.14 7.14
3.4950 3.5883 3.6816 3.7749 3.9615
57.273 58.802 60.331 61.860 64.917
Dash Number -441 -442 -443 -444 -445
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
SAE INTERNATIONAL
AS568D
Page 15 of 15
TABLE 1 - AEROSPACE SIZE STANDARDS FOR O-RINGS (CONTINUED)
Dash Number -471 -472 -473 -474 -475
ID ID Inches Inches min max 21.855 22.055 22.835 23.045 23.830 24.050 24.825 25.055 25.820 26.060
ID mm min 555.12 580.01 605.28 630.56 655.83
ID W mm Inches max min 560.20 0.269 585.34 0.269 610.87 0.269 636.40 0.269 661.92 0.269
W Inches max 0.281 0.281 0.281 0.281 0.281
W mm min 6.83 6.83 6.83 6.83 6.83
W mm max 7.14 7.14 7.14 7.14 7.14
Volume (Ref) Cubic Inches 4.1481 4.3319 4.5184 4.7050 4.8916
Volume (Ref) Cubic cm 67.975 70.987 74.043 77.101 80.159
TABLE 2 - AEROSPACE SIZE STANDARDS FOR STRAIGHT THREAD TUBE FITTING BOSS GASKETS
Dash Number -901 -902 -903 -904 -905
Tube Size (Nom) Inches 0.094 0.125 0.188 0.250 0.313
Tube Size (Nom) mm 2.38 3.18 4.76 6.35 7.94
ID Inches min 0.180 0.234 0.296 0.346 0.409
ID Inches max 0.190 0.244 0.306 0.356 0.419
ID mm min 4.57 5.94 7.52 8.79 10.39
D mm max 4.83 6.20 7.77 9.04 10.64
W Inches min 0.053 0.061 0.061 0.069 0.069
W Inches max 0.059 0.067 0.067 0.075 0.075
W mm min 1.35 1.55 1.55 1.75 1.75
W mm max 1.50 1.70 1.70 1.91 1.91
Volume (Ref) Cubic Inches 0.0019 0.0031 0.0037 0.0054 0.0062
Volume (Ref) Cubic cm 0.031 0.051 0.061 0.088 0.102
-906 -907 -908 -909 -910
0.375 0.438 0.500 0.563 0.625
9.53 11.11 12.70 14.29 15.88
0.463 0.523 0.635 0.697 0.746
0.473 0.537 0.653 0.715 0.764
11.76 13.28 16.13 17.70 18.95
12.01 13.64 16.59 18.16 19.41
0.075 0.079 0.084 0.094 0.094
0.081 0.085 0.090 0.100 0.100
1.90 2.01 2.13 2.39 2.39
2.06 2.16 2.29 2.54 2.54
0.0082 0.0102 0.0137 0.0186 0.0198
0.134 0.167 0.225 0.305 0.324
-911 -912 -913 -914 -916
0.688 0.750 0.183 0.875 1.000
17.46 19.05 20.64 22.23 25.40
0.854 0.915 0.976 1.037 1.161
0.872 0.933 0.996 1.057 1.181
21.69 23.24 24.79 26.34 29.49
22.15 23.70 25.30 26.85 30.00
0.112 0.112 0.112 0.112 0.112
0.120 0.120 0.120 0.120 0.120
2.85 2.85 2.85 2.85 2.85
3.05 3.05 3.05 3.05 3.05
0.0325 0.0345 0.0366 0.0386 0.0427
0.533 0.565 0.600 0.633 0.700
-918 -920 -924 -928 -932
1.125 1.250 1.500 1.750 2.000
28.58 31.75 38.10 44.45 50.80
1.343 1.461 1.706 2.072 2.319
1.367 1.489 1.734 2.108 2.356
34.11 37.11 43.33 52.63 58.90
34.72 37.82 44.04 53.54 59.84
0.112 0.114 0.114 0.114 0.114
0.120 0.122 0.122 0.122 0.122
2.85 2.90 2.90 2.90 2.90
3.05 3.10 3.10 3.10 3.10
0.0488 0.0547 0.0631 0.0759 0.0843
0.800 0.896 1.034 1.244 1.381
PREPARED BY SAE SUBCOMMITTEE A-6C2, SEALS OF COMMITTEE A-6, AEROSPACE ACTUATION, CONTROL AND FLUID POWER SYSTEMS
--`,```,`,,,`,`,`,```,`````,`-`-`,,`,,`,`,,`---
Provided by IHS No reproduction or networking permitted without license from IHS
Licensee=Setin Tred S.A. de C.V./5988257001, =Saavedra, Hugo Not for Resale, 11/27/2014 09:36:08 MST
Related Documents 3h463d
Sae As568d 4l5c1i
December 2019 69
Sae 6662f
September 2020 0
Norma Sae J2044 Sae J2044 2n4j3h
October 2019 547
Sae Livro 6s5w5l
April 2020 178
Sae-as5202_port_dimensions.pdf 6r21m
November 2019 107
Sae J1273 6e341s
November 2019 99More Documents from "Jose Francisco Rivera Rodriguez" 1x2k5u
Ansi Mss Sp 55 6r6tu
October 2019 92
Aws A5.28 1lf6c
December 2019 104
Sae As568d 4l5c1i
December 2019 69
Mxl Iq Manual.pdf 4823b
November 2019 50
Engranajes.pdf 3s1t5p
July 2021 0