Setting Up Kpacs 2x5oh

Setting Up K-PACS with Conquest DICOM (18-Feb-2008 / gsm)

1. Introduction This note describes how to setup the K-PACS/Conquest DICOM PACS system used at Sylvania Veterinary Hospital. The requirements for SVH are: (a)

At this time the only source of DICOM images at SVH is a Philips HDI 3500 ultrasound system. It is located at the network address of 192.168.1.100, and is set to use an AET of HDI3000, on the default port of 104.

(b)

The ultrasound system will talk to the Conquest DICOM server, which is to be setup on the workstation CONSULT3 at address 192.168.1.15. The Conquest DICOM server will use an AET of CONQUEST and operate on the default port of 5678. All images from the ultrasound will be stored on CONSULT3 by Conquest, which will act as the PACS server for the rest of the workstations.

(c)

The K-PACS viewer will be used on each of the client workstations to access images stored in the PACS. The K-PACS DICOM server in each workstation will be setup with an AET like KPACS-F1, KPACS-C3 etc. and all client workstations will use port 5679.

2. s The following software must be ed from the internet to setup this system: (a)

The Conquest DICOM software can be dowloaded from: http://www.xs4all.nl/∼ingenium/dicom.html At the time of writing, the current version of Conquest is 1.4.13, and the following files should be ed: dicomserver1413.zip bdeinstall5.zip

(b)

(5685 KB) (4022 KB)

The K-PACS software can be ed from: http://www.k-pacs.net Click on S, and select the K-PACS All-in-one Installer. The current version is V1.5.0, and is 6.2MB in size.

3. Setup Ultrasound Setting up the ultrasound equipment has been covered in an earlier document,1 and the ultrasound should be setup identically here.

4. Setup Conquest DICOM Setting up Conquest DICOM has also been covered in an earlier document,1 and the same setup should be used here except for the following modifications to dicom.ini: 1

See Sylvania Veterinary Hospital: DICOM Image Archive for Ultrasound (2007)

Page 1 of 3

MyACRNema = CONQUEST FileNameSyntax = 8 The first change simply sets the AET fro the Conquest DICOM server, and the second forces the PACS hierarchy to be organised as: ID[32]\Studyuid\Seriesuid\Imageuid.dcm

5. Setup K-PACS The following procedure should be followed on all the workstations that are to have access to the PACS system: (a)

Run the K-PACS Installer, and let it install into the default location of C:\KPacs, with images saved in C:\KPacs\Imagebox.

(b)

The AET should be set in accordance with the following table, and the port should be set to 5679 on all workstations. Workstation Frontdesk1 Frontdesk2 Consult1 Consult2 Consult3 Pathology Preproom1 Preproom2 Kennelroom Office

(c)

AET KPACS-F1 KPACS-F2 KPACS-C1 KPACS-C2 KPACS-C3 KPACS-PA KPACS-P1 KPACS-P2 KPACS-K KPACS-O

Once the K-PACS installation has completed, start K-PACS and click on the Dicom Configuration button. Edit the Conquest(Expamle) found there to have the following parameters: Logical Name: DICOM AE Title: IP Address: Port number:

Conquest CONQUEST 192.168.1.15 5678

(d)

Click on the Save button to save these changes, and then click on the Local settings button to open up that dialog.

(e)

Make sure the following parameters are set: Installation directory: C:\KPacs\ K-PACS Server Application Entity Title: KPACS-F1 Path of local imagebox: C:\KPacs\Imagebox\ Server port: 5679

(f)

Click the Server Tool button. When the dialog opens up, you can modify any incorrect parameters from the previous window. As well, set Overflow management to based on date of registration, and set max days on local to 30.

(g)

Click the stop K-Pacs Server button, and then the start K-Pacs Server button. This will ensure Page 2 of 3

the server is running with any changed parameters. Close the dialog, and click Save settings to close the Local settings dialog. (h)

K-PACS should now be fully configured, ready to use.

To test that K-PACS is working properly, start the Conquest server, and start the K-PACS client. In K-PACS, click on the Network tab in the Query section, and select Conquest. This enables K-PACS to retrieve images from Conquest. Now, with nothing entered in the Search filter section, click Search. After a warning message, a complete list of the patients found in the Conquest PACS should appear. Select a study for one of these patients, and click Viever. If all is well, the DICOM images for this study will be displayed.

5. Need Help ? For assistance, Greg Munro on (04)1720-6191 or email [email protected].

–oOo–

Page 3 of 3