Smart Energy Meter Project Report 2g1p65

SMART ENERGY METER

KEYWORDS ACC

: Accumulator

B

:

B

PSW

:

Program Status Word

SP

:

Stack Pointer

DPTR

:

Data Pointer

DPL

:

Low byte

DPH

:

High byte

P0

:

Port 0

P1

:

Port 1

P2

:

Port 2

P3

:

Port 3

IE

:

Interrupt Enable control

IP

:

Interrupt Priority control

TMOD

:

Timer/counter Mode control

TCON

:

Timer/counter control

T2CON

:

Timer/counter 2 control

T2MOD

:

Timer/counter mode2 control

TH0

:

Timer/counter 0high byte

TL0

:

Timer /counter 0low byte

TH1

:

Timer/counter 1high byte

TL1

:

Timer/counter 1low byte

TH2

:

Timer/counter 2 high byte

TL2

:

Timer/counter 2 low byte

SCON

:

Serial control

SBUF

:

Serial data buffer

PCON

:

Power control

IR

:

Infra Red 1

SMART ENERGY METER

INDEX ACKNOWLEDGE ABSTRACT

-----------------------------------------------------------------------

I.INTRODUCTION II. LITERATURE SURVEY 2.1 Motivation 2.2 Background 2.3 Aim 2.4 Requirement Analysis 2.4.1 Hardware Requirements 2.4.2 Software Requirements 2.5 Scope 2.6 Advantages

6 7 9 11 11 11 12 12 12 12 12

III.DESIGN METHODOLOGY 3.1 Hardware system design 3.1.1 Block level design of Smart Energy Meter 3.1.2 Selection of Hardware 3.1.3 Design consideration of Microcontroller 3.1.3.1 8051 3.1.3.2 Internal architecture of P89C51RD2FN 3.1.3.2.1 I/O ports 3.1.3.2.2 Interrupt controls 3.1.3.2.3 Bus controllers 3.1.3.2.4 Memory organization 3.1.3.2.5 s in 8051 3.1.3.2.6 Oscillator 3.1.3.3 Features 3.1.4 Serial communication 3.1.4.1 Introduction 3.1.4.2 Baud rate 3.1.5 Hardware design of LCD 3.1.5.1 LCD screen 3.1.5.2 Features 3.1.5.3 Pin configuration 3.1.5.4 Specifications 3.1.5.5 Functionality of LCD in project 3.1.6 MAX232 3.1.6.1 Pin configuration 3.1.7 RS232 (Female port) 3.1.7.1 Voltage levels 3.1.7.2 Pin configuration 3.1.7.3 DB9 interfacing microcontroller using MAX232 3.1.8 Serial port connector 3.1.9 Design of KEYPAD

14 14 15 15 15 16 17 18 19 19 20 22 23 24 24 25 25 26 29 29 30 32 32 33 33 33 34 34 35 35 2

SMART ENERGY METER

3.1.10 IR sensors and IC NE555 Timer 3.1.10.1 Photo transmitter 3.1.10.2 Principle of operation 3.1.10.3 Application 3.1.10.4 Features 3.1.10.5 IR receivers 3.1.10.6 Photo transistor 3.1.10.7 Principle of operation 3.1.11 IC NE555 timer 3.1.12 Resistors 3.1.13 Capacitors 3.1.14 Crystal oscillators 3.2 Software design 3.2.1 Liquid Crystal Display 3.2.1.1 Initialization of LCD 3.2.1.2 Checking busy state of LCD 3.2.2 KEYPAD 3.2.2.1 Flow chart of keyboard scanning algorithm

37 37 38 39 39 39 39 39 40 41 41 42 43 43 43 43 47 47

IV. IMPLEMENTATION 4.1 Hardware implementation 4.1.1 Complete Schematic of Smart Energy Meter 4.1.2 Connections of P89C51RD2FN 4.1.3 Pin connections of LCD 4.1.4 Keypad connections 4.1.5 MAX232 and DB9 connections 4.1.6 IC555 timer and IR transmitter connections

49 50 51 52 53 53 54

V. SOFTWARE IMPLEMENTATION 5.1 JHD162A LCD interfacing 5.1.1 Initialization of LCD 5.1.2 Initialization sequence code 5.1.3 Checking the busy state of LCD 5.1.4 Writing the command to display 5.1.5 Writing data to display 5.1.6 Displaying the data into LCD 5.1.7 4*4 matrix Keypad interfacing 5.1.8 Sensors

56 56 56 56 57 57 57 58 58

VI. DEBUGGING TECHNIQUES 6.1 KEIL micro vision debugger 6.1.1 Introduction to KEIL IDE 6.1.2 Features 6.1.3 Steps to follow while writing program in KEIL 6.2 Flash Magic 6.2.1 Features 6.3 Null MODEM checking (HYPER TERMINAL) 6.4 Hardware debugging techniques

CONCLUSION

61 61 61 62 63 63 64 65 65

3

SMART ENERGY METER

RESULT VII. BIBILOGRAPHY VIII. APPENDIX KEIL MICROVISION IDE FLASH MAGIC SET UP OF HYPER TERMINAL COMPLETE CODE

66

67 68 77 80 83

4

SMART ENERGY METER

ABSTRACT

Saving energy is high on the agenda for consumers and businesses, but with most of the electrical devices today, it„s difficult to know how much energy we are actually using at any given point in time. Smart Energy Meter is a meter which helps the consumers to know their day to day power consumption to better control their usage and producers to manage production. This meter records consumption of electric energy in intervals of hour or less. Smart meters enable two-way communication between the meter and the central system. The proposed project comprises of hardware design using a low-cost 8-bit P89C51RD2xx microcontroller and the complete hardware design will be proposed .The Communication is through SMS.They are two one is and second is . By this the cost per unit can be changed by the concerned officerThe system software driver is also developed using embedded-C programming language in Keil µVision 4 IDE. . Smart meters are also believed to be a less costly alternative to traditional interval or time-of-use meters and are intended to be used on a wide scale with all customer classes, including residential customers. The project also addresses about the various debugging tools such as Keil µVision 4 C51 debugger and Flash magic tool 9.25 version used to test the implemented prototype.

Keywords: Embedded System , Micro controller , Cross-compiler and Debugging.

5

SMART ENERGY METER

CHAPTER-1

6

SMART ENERGY METER

CHAPTER - I INTRODUCTION Now-a-days electricity has become a basic need to humans. The consumption of electricity has increased a lot compared to the past years. The theft of electricity has also become a problem these days and there is no control over the loss due to theft of electricity. In this project we present you the smart energy meter device used to measure the consumption of the electricity by the individual and provide security against theft of electricity. A smart meter is usually an electrical meter that records consumption of electric energy in intervals of an hour or less and communicates that information at least daily back to the utility for monitoring and billing purposes. Smart meters enable two-way communication between the meter and the central system. Unlike home energy monitors, smart meters can gather data for remote reporting. The term Smart meter often refers to an electricity meter, but it can increasingly also mean a device measuring natural gas or water consumption. Smart energy meter is software based, power efficient device that accurately tracks energy consumption and performs computation. Meter readings can be transmitted to distributors/utilities over wireless media; thus, eliminating the need of manual meter reading collection process. The smart energy meter offers major benefits to both customers and companies in of efficiency, reliability, and cost saving. Imagine if you knew how much energy you were consuming at home at any time of the day, and knew how much energy each device was using, will you stop using those energy hog appliances? or use them at the time of the day when the energy is cheapest? in the economy turmoil we are currently in, I believe all of us are willing to make those small sacrifices to lower down the bill numbers at the end of the month. Smart energy meters are devices that will sit on your home, monitor energy data from your electricity meter, and let you know how much energy you are using – this put more control on your hands on how you spend your energy at home. Conventional electricity meters are normally hidden somewhere on a wall on the basement, and the only time you realize how much energy you‟ve been spending is when the bill hit the door. The new smart meters will provide Indian consumers with information regarding energy consumption that was not previously available with a traditional meter. This system will allow the easy disconnection of defaulted customers and power connections from a remote site. The new smart system is also able to instantly detect tampering with the power lines and sends signals to security personnel if necessary. Utility employees will also have the ability to change a customer‟s billing method from pre paid to post paid in a matter of seconds, without having to physically visit the meter.

7

SMART ENERGY METER

CHAPTER-2

CHAPTER- II 8

SMART ENERGY METER

LITERATURE SURVEY

2.1 MOTIVATION In the present scenario, the use of advanced technologies such as digital metering has become extremely necessary to achieve greater efficiency, theft reduction to reduce AT & C losses and to improve revenue collection. The utilities and planners should now focus on best use of electronic technology to develop a full „smart‟ system, which is capable of offering long term benefits and comprehensive solutions in addition to theft reduction. In undeveloped and under developing countries proper distribution of power has to be done. So it‟s the duty of us, engineers to develop the equipments to reduce the power losses and power thefts.

2.2 BACKGROUND An electricity meter or energy meter is a device that measures the amount of electric energy consumed by a residence, business, or an electrically powered device. Electricity meters are typically calibrated in billing units, the most common one being the kilowatt hour. Periodic readings of electric meters establish billing cycles and energy used during a cycle. In settings when energy savings during certain periods are desired, meters may measure demand, the maximum use of power in some interval. In some areas, the electric rates are higher during certain times of day, to encourage reduction in use. The billing of the electricity consumption in these present days are done with human observation, but this project deals with the communication for the proper billing through GSM without any human involvement. Due to theft of electricity leads to power shut down in many of the rural areas in India.

2.3 AIM: To design and implement the smart energy meter by using 8051 micro controller coded in embedded c program.

9

SMART ENERGY METER

2.4 Requirement Analysis: 2.4.1 Hardware requirements The components those are required for “Smart Energy Meter” project is given below. 1. 2. 3. 4. 5. 6. 7. 8.

Micro Controller (P89C51R2FN). MAX 232. DB9 or RS232 connector. Power supply. 4*4 matrix keypad. LCD display. 555 timer IC IR sensors.

2.4.2 Software requirements 1. FLASH MAGIC Philips Serial ISP programming utility. 2. KEIL µVision 4IDE C51 Embedded Cross Compiler.

2.5 SCOPE: The scope of the project work is to introduce advanced technology in converting dc voltage in to ac voltage and introducing smart energy metering concept. In future this project can be used to measuring natural gas or water consumption. These meters can be connected to GSM module and data (i.e. consumption) can be transmitted over GSM networks and the bills can be automatically issued to the particular customer through SMS. By making small modifications in the program (code) we can break the connection if does not pay the bills in time. There is no need for the electricity officials to visit the spot to disconnect the connections i.e., everything can be controlled over the GSM module. The can also sell the electricity to the government which is created in his home using solar cells. These meters can also be used as prepaid energy meters by slightly modifying them.

2.6 Advantages:      

More accurate bills. Lower bills. Track of energy usage. Sell energy back to the grid. Flexible tariffs. No more meter readings.

10

SMART ENERGY METER

CHAPTER-3

11

SMART ENERGY METER

CHAPTER - III DESIGN METHODOLOGY

3.1 Hardware System Design: 3.1. 1 Block level design of smart energy meter The functional diagram of “Smart Energy Meter” using GSM or Hyper Terminal is given below.

Fig 3.1 : Functional block diagram of Smart Energy Meter.

12

SMART ENERGY METER

3.1.2 SELECTION OF HARDWARE: The hardware selected must be such a way that  Low cost  Low power consumption, small, fast  Continually reacts to changes in the system‟s environment  Must compute certain results in real-time without delay  Simple design  Easy maintainability and interoperability  Bug-free/Correctness, safety, many more

3.1.3 DESIGN CONSIDERATIONS OF MICROCONTROLLER WHY P89C51RD2BN?  The system requirements and control specifications clearly rule out the use of 16, 32 bit microcontrollers.  The P89C51RD2xx contains non-volatile 64KB Flash program memory that is both parallel programmable and serial In-System and In-Application Programmable.  In-System Programming (ISP) allows the to new code while the microcontroller sits in the application.  In-Application Programming (IAP) means that the microcontroller fetches new program code and reprograms itself while in the system. This allows for remote programming over a modem link. A default serial loader (boot loader) program in ROM allows serial In-System programming of the Flash memory via the UART without the need for a loader in the Flash code. For InApplication Programming, the program erases and reprograms the Flash memory by use of standard routines contained in ROM.

3.1.3.1 8051 The 8051 is an 8 bit microcontroller originally developed by Intel in 1980. It is one of the most popular microcontrollers in the world for its high performance, rich instruction set and low cost. This device is a Single-Chip 8-Bit Microcontroller manufactured in an advanced CMOS process and is a derivative of the 8051 microcontroller family. The instruction set is 100% compatible with the 8051 instruction set. Three criteria in choosing the microcontrollers are as follows: 1. Meeting the computing needs of the task at hand efficiently and cost effectively. 2. Availability of software development tools such as compliers, assemblers, and debuggers. 3. Wide availability and reliable sources of the microcontroller.

13

SMART ENERGY METER

Some of the features that have made the 8051 popular are:             

64 KB on chip program memory. 128 bytes on chip data memory (RAM). 4 banks. 128 defined software flags. Four 8-bit data bus 16-bit address bus 32 general purpose s each of 8 bits 16 bit timers (usually 2, but may have more, or less). 3 internal and 2 external interrupts. Bit as well as byte addressable RAM area of 16 bytes. Four 8-bit ports, (short models have two 8-bit ports). 16-bit program counter and data pointer. 1 Microsecond instruction cycle with 12 MHz Crystal.

8051 models may also have a number of special, model-specific features, such as UARTs, ADC, Op Amps, etc...

3.1.3.2 Internal architecture of P89C51RD2XX The P89C51RD2xx contains a non-volatile 8KB/16KB/32KB/64KB Flash program memory that is both parallel programmable and serial In-System and InApplication Programmable. In-System Programming (ISP) allows the to new code while the microcontroller sits in the application. In-Application Programming (IAP) means that the microcontroller fetches new program code and reprograms itself while in the system.

14

SMART ENERGY METER

The internal architecture of P89C51RD2FN microcontroller with suitable diagram

Fig 3.2: Internal architecture of P89C51RD2FN.

3.1.3.2.1 I/O ports: All 8051 microcontrollers have 4 I/O ports each comprising 8 bits which can be configured as inputs or outputs. Accordingly, in total of 32 input/output pins enabling the microcontroller to be connected to peripheral devices are available for use. Pin configuration, i.e. whether it is to be configured as an input (1) or an output (0), depends on its logic state. In order to configure a microcontroller pin as an input, it is necessary to apply logic zero (0) to appropriate I/O port bit. In this case, voltage level on appropriate pin will be 0. The 4I/O ports of 8051 are designated as port 0, port 1, port 2, and port 3. All these I/O ports have different functions and conditions while connecting to external peripherals.

3.1.3.2.1. a Port 0 (P0)The P0 port is characterized by two functions. If external memory is used then the lower address byte (addresses A0-A7) is applied on it. Otherwise, all bits of this port are configured as inputs/outputs. The other function is expressed when it is 15

SMART ENERGY METER

configured as an output. Unlike other ports consisting of pins with built-in pull-up resistor connected by its end to 5 V power supply; pins of this port have this resistor left out. If any pin of this port is configured as an input then it acts as if it “floats”. Such an input has unlimited input resistance and undetermined potential. When the pin is configured as an output, it acts as an “open drain”. By applying logic 0 to a port bit, the appropriate pin will be connected to ground (0V). By applying logic 1, the external output will keep on “floating”. In order to apply logic 1 (5V) on this output pin, it is necessary to built in an external pull-up resistor. 3.1.3.2.1. b Port 1 (P1)P1 is a true I/O port, because it doesn't have any alternative functions as is the case with P0, but can be configured as general I/O only. It has a pull-up resistor builtin and is completely compatible with TTL circuits. 3.1.3.2.1. c Port 2 (P2)P2 acts similarly to P0 when external memory is used. Pins of this port occupy addresses intended for external memory chip. This time it is about the higher address byte with addresses A8-A15. When no memory is added, this port can be used as a general input/output port showing features similar to P1. 3.1.3.2.1. d Port 3 (P3)All port pins can be used as general I/O, but they also have an alternative function. In order to use these alternative functions, a logic one (1) must be applied to appropriate bit of the P3 . In of hardware, this port is similar to P0, with the difference that its pins have a pull-up resistor built-in.

3.1.3.2.2 Interrupts controls: There are 7 kinds of interrupt controllers that 8051 handles. They are as follows. 1. 2. 3. 4. 5. 6. 7.

INT0 external interrupt. INT1 external interrupt. Timer 0 Timer 1 Reset. Transmitted interrupt (TXD). Received interrupt (RXD).

There are two types of external hardware interrupts. Pin 12 (P3.2) and pin 13 (P3.3) of the 8051, designated as INT0 and INT1, are used as external hardware interrupts. Upon the activation of these pins, the 8051 gets interrupted in whatever it is doing and jumps to the vector table to perform the interrupt service routines (ISR).

Timer 0 and timer 1 interrupts can be used in pooling method. In this method, we have to wait until the TF is raised. The problem with this method is that the microcontroller is tied down the controller. If the timer interrupt in the IE is enabled, whenever the timer rolls over, TF is raised, and the microcontroller is

16

SMART ENERGY METER

interrupted in whatever it is doing, and jumps to the interrupts vector table to service the ISR.

Reset pin is an input pin and is active high (normally low). Upon applying a high pulse to this pin, the microcontroller will reset and terminate all activities. This is often referred to as power-on reset. In order for RESET input to be effective, it must have a minimum duration of two machine cycles. In other words, the high pulse must be high for a minimum of two machine cycles before it is allowed to go low. TXD and RXD are serial communication interrupts.

3.1.3.2.3 BUS CONTROLS The main bus controllers available in 8051 are ALE, EA, RST and PSEN. ALE (Address Latch Enable): Output pulse for latching the low byte of the address during an access to external memory. In normal operation, ALE is emitted twice every machine cycle, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. ALE can be disabled by setting SFR auxiliary.0. With this bit set, ALE will be active only during a MOVX instruction. EA (External Access Enable/Programming Supply Voltage): EA must be externally held low to enable the device to fetch code from external program memory locations. If EA is held high, the device executes from internal program memory. The value on the EA pin is latched when RST is released and any subsequent changes have no effect. This pin also receives the programming supply voltage (VPP) during Flash programming. RST (Reset): A high on this pin for two machine cycles while the oscillator is running resets the device. An internal resistor to VSS permits a power-on reset using only an external capacitor to VCC. PSEN (Program Store Enable): The read strobe to external program memory. When executing code from the external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. PSEN is not activated during fetches from internal program memory.

3.1.3.2.4 Memory organization The 8051 has two types of memory and these are Program Memory and Data Memory. Program Memory (ROM) is used to permanently save the program being executed, while Data Memory (RAM) is used for temporarily storing data and intermediate results created and used during the operation of the microcontroller. Depending on the model in use (we are still talking about the 8051 microcontroller

17

SMART ENERGY METER

family in general) at most a few Kb of ROM and 128 or 256 bytes of RAM is used. All 8051 microcontrollers have a 16-bit addressing bus and are capable of addressing 64 kb memory. It is neither a mistake nor a big ambition of engineers who were working on basic core development. It is a matter of smart memory organization which makes these microcontrollers a real “programmers‟ goody“.

3.1.3.2.4. a Program memory The first models of the 8051 microcontroller family did not have internal program memory. It was added as an external separate chip. These models are recognizable by their label beginning with 803 (for example 8031 or 8032). All later models have a few Kbyte ROM embedded. Even though such an amount of memory is sufficient for writing most of the programs, there are situations when it is necessary to use additional memory as well. A typical example is so called lookup tables. They are used in cases when equations describing some processes are too complicated or when there is no time for solving them. In such cases all necessary estimates and approximates are executed in advance and the final results are put in the tables (similar to logarithmic tables).

3.1.3.2.4. b Data memory Data Memory is used for temporarily storing data and intermediate results created and used during the operation of the microcontroller. Besides, RAM memory built in the 8051 family includes many s such as hardware counters and timers, input/output ports, serial data buffers etc. The previous models had 256 RAM locations, while for the later models this number was incremented by additional 128 s. However, the first 256 memory locations (addresses 0-FFh) are the heart of memory common to all the models belonging to the 8051 family.

3.1.3.2.5 s in 8051 In the U, s are used to store information temporarily. That information could be a byte of data to be processed, or an address pointing to the data to be fetched. The vast majority of 8051 s are 8- bit s. In the 8051 there is only one data type: 8 bits. With an 8-bit data type, any data larger than 8 bits must be broken into 8- bit chunks before it is processed. The most widely used s of the 8051 are A(Accumulator), B, and SPF (special function s) and PSW (Program Status Word).

A is a general-purpose used for storing intermediate results obtained during operation. Prior to executing an instruction upon any number or operand it is necessary to store it in the accumulator first. All results obtained from arithmetical operations performed by the ALU are stored in the accumulator. Data to be moved from one to another must go through the accumulator. In other words, the A is the most commonly used and it is impossible to 18

SMART ENERGY METER

imagine a microcontroller without it. More than half instructions used by the 8051 microcontroller use somehow the accumulator. Multiplication and division can be performed only upon numbers stored in the A and B s. All other instructions in the program can use this as a spare accumulator (A).

3.1.3.2.5. a R s (R0-R7) This is a common name for 8 general-purpose s (R0, R1, R2 ...R7). Even though they are not true SFRs, they deserve to be discussed here because of their purpose. They occupy 4 banks within RAM. Similar to the accumulator, they are used for temporary storing variables and intermediate results during operation. Which one of these banks is to be active depends on two bits of the PSW . Active bank is a bank the s of which are currently used.

3.1.3.2.5. b SFR (Special Function s) Special Function s (SFRs) are a sort of control table used for running and monitoring the operation of the microcontroller. Each of these s as well as each bit they include, has its name, address in the scope of RAM and precisely defined purpose such as timer control, interrupt control, serial communication control etc. Even though there are 128 memory locations intended to be occupied by them, the basic core, shared by all types of 8051 microcontrollers, has only 21 such s.

3.1.3.2.5.c PROGRAM STATUS WORD (PSW):

     

CY: Carry out from accumulator MSB of ALU operand AC: Auxiliary carry for BCD operations FO: General purpose RS1 & RS0: For banks selection ( RB0-RB3) OV: Overflow flag P: Parity of accumulator set by hardware to 1 if it contains odd no of 1‟s

Table 3.1.The contents of (RS1-RS0) enable the working banks

19

SMART ENERGY METER

RS 1

RS 0

BANKS AND S

0

0

BANK 0 (00H-07H)

0

1

BANK 1 (08H0FH)

1

0

BANK 2 (10H-17H)

1

1

BANK 3 (18H-1FH)

Carry flag: Carry flag is set whenever there is carry out from the MSB. This flag is after 8bit ADD/SUB operation. It can also be set to 1 or 0 directly using SETB C or CLR C Auxiliary carry: If there is a carry from D3 to D4 position during Add/Sub operation, this bit will set. Otherwise, it is cleared. This flag is used for BCD operations. Parity flag reflects the number of 1‟s in A. If „A‟ contains an odd number of 1‟s, then P=1. Therefore P=0, if A has an even number of 1‟s. Overflow flag: This flag is set whenever the result of a signed number operation is too large to be accommodated in 7 bits, causing the higher order bit to overflow into the sign bit. 3.1.3.2.6 Oscillator: The microcontroller used in this project, P89C51RD2FN requires a baud rate of 9600. To acquire this baud rate, an 11.0592 MHz crystal must be connected between 19th and 20th pins of controller. The determination of machine cycle frequency and Baud rate is as follows. MCF = (XTL freq / 12) = (11.0592 * 10^6) / 12 = 921.6 KHz

Baud rate = MCF/32 = (921.6 × 10^3) / 32 = 28800 Hz 20

SMART ENERGY METER

Where MCF = Machine Cycle Frequency, XTL = Crystal.

To synchronize with timer1 (TH1) to set the baud rate as 9600 we need to set those value as -3 (decimal) or FD (Hexadecimal) so as to divide the baud rate i.e.. 28800Hz should be dividing with the decimal value of TH1 to get 9600 value.

Fig 3.3: Oscillator Connections

C1, C2 = 33pF.

3.1.3.3 FEATURES      

80C51 Central Processing Unit On chip Flash Program Memory with In-System Programming (ISP) and InApplication Programming Boot ROM contains low level Flash programming routines for ing via the UART Can be programmed by the end- application(IAP) s 6-clock/12 clock mode via parallel programmer(default clock mode after Chip Erase is 12-clock) Speed up to 20MHz with 6-clock cycles per machine cycle (40MHz equivalent performance), up to 33MHz with 12 clocks per machine 21

SMART ENERGY METER

            

cycle RAM expandable externally to 64Kbytes Four interrupt priority levels Seven interrupt sources Four 8-bit I/O ports Full-duplex enhanced UART 8-Bit ALU , with 2 s A & B 11 bit program counter & data pointer 8-Bit program status word 8 bit stack pointer 4s banks, each containing 8 s 16bytes , which may be addressed at bit level 80 bytes of general purpose data Two 16 bit timer/counter – T0 & T1

Control s –TCON, TMOD, SCON, PCON and IP & IE oscillator & clock circuits.

3.1.4 SERIAL COMMUNICATION 3.1.4.1 Introduction In order to connect microcontroller to a modem or a pc to modem a serial port is used. Serial is a very common protocol for device communication that is standard on almost every PC. Most computers include two RS-232 based serial ports. Serial is also a common communication protocol that is used by many devices for instrumentation; numerous GPIB-compatible devices also come with an RS232 port. Furthermore, serial communication can be used for data acquisition in conjunction with a remote sampling device. Typically, serial is used to transmit ASCII data. Communication is completed using 3 transmission lines. (1) Ground, (2) Transmit and (3) Receive. Since serial is asynchronous, the port is able to transmit data on one line while receiving data on another. Other lines are available for handshaking, but are not required. The important serial characteristics are baud rate, data bits, stop bits, and parity. For two ports to communicate, these parameters much match. Serial communication is a popular means of transmitting data between a computer and a peripheral device such as a programmable instrument or even another one bit at a time, over a single communication line to a receiver. You can use this method when data transfer rates are low or you must transfer data over long distances. Serial communication is popular because most computers have one or more serial ports, so no extra hardware is needed other than a cable to connect the instrument to the computer or two computers together. Any device you connect to the serial port will need the serial transmission converted back to parallel so that it can be used. In serial communication, the data will be sent from one system to another in bit by bit notation. Serial Ports come in two “sizes”, there are the D-Type 25 pin connector and the D-Type 9 Pin connector both of which are male on the back of the PC, and thus you will require a female connector on your device. The RS-232 and RS-485 come under serial communication. 22

SMART ENERGY METER

3.1.4.2 Baud Rate: It is a speed measurement for communication. It indicates the number of bit transfers per second. For example, 300 baud is 300 bits per second. When a clock cycle is referred it means the baud rate. For example, if the protocol calls for a 4800 baud rate, then the clock is running at 4800Hz. This means that the serial port is sampling the data line at 4800Hz. Common baud rates for telephone lines are 12200, 28800 and 33600. Baud rates greater than these are possible, but these rates reduce the distance by which devices can be separated. These high baud rates are used for device communication where the devices are located together, as is typically the case with GPIB devices.

3.1.5 HARDWARE DESIGN OF LCD The LCD (Liquid Crystal Display) used to display the output to the in the form of GUI (Graphic Interface) and a mono chromatic display. LCD used in this project is JHD162A series. There are 16 pins in all. They are numbered from left to right 1 to 16 (if you are reading from the backside). LCD shown above is marked to indicate which the 1st pin was and which the 16th was. In our project, we use a JHD162A LCD Display which has 2 rows and 16 characters. It contains internal 1 byte latch. It has a better contrast and a wider viewing angle. To develop a protocol to interface this LCD with 89C51 first we have to understand how they functions. These displays contain two internal byte-wide s, one for command and second for characters to be displayed. There are three control signals called R/W, RS and EN. Select By making RS signal 0 you can send different commands to display. These commands are used to initialize LCD, to display pattern, to shift cursor or screen etc. You can see the markings right next to 1st and 16th pins. The 16by2 LCD with connections is as given below

23

SMART ENERGY METER

Fig 3.4: Pin configuration of LCD 3.1.5.1 LCD screen:LCD screen consists of two lines with 16 characters each. Each character consists of 5*7 dot matrix. Contrast on display depends on the power supply voltage and whether messages are displayed in one or two lines. For that reason, variable voltage 0-Vdd is applied on pin marked as VEE. Trimmer potentiometer is usually used for that purpose. Some versions of displays have built in backlight (blue or green diodes). When used during operating, a resistor for current limitation should be used (like with any LE diode)

The main control pins on JHD162A are data lines, read or write and enable. LCD is finding wide spread use replacing LEDs (seven segment LEDs or other multi segment LEDs) because of the following reasons: 1. The ability to display numbers, characters and graphics. This is in contrast to LEDs, which are limited to numbers and a few characters. 2. Incorporation of a refreshing controller into the LCD, thereby relieving the U of the task of refreshing the LCD. In contrast, the LED must be refreshed by the U to keep displaying the data. 3. Ease of programming for characters and graphics. 4. These components are “specialized” for being used with the microcontrollers, which means that they cannot be activated by standard IC circuits. They are used for writing different messages on a miniature LCD.

24

SMART ENERGY METER

Fig 3.5: LCD Display

3.1.5.1. a Data lines (D0-D7): The data lines are connected to the parallel port of the microcontroller. While connecting the data lines to port0 no pull up resistors are required. These data lines are used to the data from U i.e. controller to LCD internal memory and to commands from LCD to U. Pin 7 is the Least Significant Bit (LSB) and pin 14 is the Most Significant Bit (MSB) of the data inputs. If you want to display some number or letter on the display, you have to input the appropriate „codes‟ for that character on these pins. These pins are also used for giving certain commands to the display like clearing the display or moving the cursor to a different location. Upon giving the correct signals to the 3 control pins, the character codes or the commands that you have given to the Data pins will be written to the display or executed by the LCD respectively. To make it easier to give the appropriate inputs to these pin, i recommend wiring up a DIP switch to these pins.

3.1.5.1. b Read and write: Generally, we always use the LCD to show things on the screen. However, in some rare cases, we may need to read from the LCD what it is displaying. In such cases, the R/W pin is used. However, this function is beyond the scope of post and will not be explained. For all practical purposes, the R/W pin has to be permanently connected to GND.

The timing diagram for write and read operation of JHD162A is as follows

Write operation: 25

SMART ENERGY METER

Fig 3.6: Timing diagram of write operation in LCD.

Read operation:

Fig 3.7: Timing diagram of read operation in LCD.

3.1.5.1. c Enable Pin: The enable pin has a very simple function. It is just the clock input for the LCD. The instruction or the character data at the data pins (D0-D7) is processed by the LCD on the falling edge of this pin. The Enable pin should be normally held at Vcc by a pull up resistor. When a momentary button switch is pressed, the Pin goes low and back to high again when you leave the switch. Your instruction or character will be executed on the falling edge of the pulse. (i.e. the moment the switch closes). 3.1.5.1. d Reset pin: The LCD has basically two operating modes: Instruction mode and Character Mode. Depending on the status of this pin, the data on the 8 data pins (D0-D7) is treated as either an instruction or as character data. You have to activate the command mode if you want to give an Instruction to the LCD. Example – “Clear the display”, “Move cursor to home” etc. You have to activate the character mode if you want to tell the LCD to display some character. To set the LCD in Instruction mode, you set

26

SMART ENERGY METER

the 4th pin of the LCD (R/S) to GND. To put it in character mode, you connect it to Vcc. 3.1.5.2 Features • RS232 compatible serial interface (2400 & 9600 Baud Selectable) • Externally selectable serial polarities (Inverted & Non-Inverted) • Serially controllable contrast and backlight levels • 8 programmable custom characters • 16 Byte serial receive buffer 3.1.5.3 Pin Configuration: There are pins along one side of the small printed board used for connection to the microcontroller. There are total of 16 pins marked with numbers .Their function is described in the table below: Table 3.2 Pin Connections Description Pins 1 – 8

Description

Pins 9 -16

Pin1

Ground

Pin9

Pin2

VCC (+5)

Pin10

Pin3

Contrast

Pin11

D4

Pin12

D5

Pin13

D6

Pin14

D7

Pin4

Pin5

Pin6

Data/Comman d (R/S) Read/Write (W) Enable (E1) D0 (Not Used

Pin7

in 4bit

Pin15

operation)

Description D2 (Not Used in 4bit operation) D3 (Not Used in 4bit operation)

VCC (LEDSV+)

D1 (Not Used Pin8

in 4bit

Pin16

Ground

operation)

27

SMART ENERGY METER

3.1.5.4 SPECIFICATIONS:            

Number of Characters: 16 characters x 2 Lines Character Table: English-European (RS in Datasheet) Module dimension: 80.0mm x 36.0mm x 13.2mm(MAX) View area: 66.0 x 16.0 mm Active area: 56.2 x 11.5 mm Dot size: 0.56 x 0.66 mm Dot pitch: 0.60 x 0.70 mm Character size: 2.96 x 5.46 mm Character pitch: 3.55 x 5.94 mm LCD type: STN, Positive, Yellow/Green Duty: 1/16 View direction: Wide viewing angle

To start with LCD the should initialize it first which should be programmed with its LCD commands. The LCD commands are given

28

SMART ENERGY METER

Table 3.3 Commands for LCD

CODE

COMMANDS TO THE LCD

1

Clear display screen

2

Return home

4

Shift cursor to left

5

Shift display right

6

Shift cursor to right

7

Shift display left

8

Display off, cursor off

A

Display off, cursor on

C

Display on, cursor off

E

Display on, cursor blinking

F

Display off, cursor blinking

10

Shift cursor position to left

14

Shift cursor position to right

18

Shift entire display left

1c

Shift entire display right

80

Force cursor to begin in 1st row

C0

Force cursor to begin in 2nd row

38

2 lines &5x7 matrix

29

SMART ENERGY METER

Fig 3.8: LCD Interface with P89C51RD2XX 3.1.5.5 Functionality of LCD in this project:  LCD is used to display any message, like authentication.  It displays the menu of operation, which contains two options automatic and settings.  It displays the amount of power utilized and price for the relevant consumed power.  It displays the to send the data to HyperTerminal.

3.1.6 MAX 232: Max232 IC is a specialized circuit which makes standard voltages as required by RS232 standards. This IC provides best noise rejection and very reliable against discharges and short circuits. MAX232 IC chips are commonly referred to as line drivers. To ensure data transfer between PC and microcontroller, the baud rate and voltage levels of Microcontroller and PC should be the same. The voltage levels of microcontroller are logic1 and logic 0 i.e., logic 1 is +5V and logic 0 is 0V. But for PC, RS232 voltage levels are considered and they are: logic 1 is taken as -3V to -25V and logic 0 as +3V to +25V. So, in order to equal these voltage levels, MAX232 IC is used. Thus this IC converts RS232 voltage levels to microcontroller voltage levels and vice versa.

30

SMART ENERGY METER

3.1.6.1 Pin Configuration:

Fig 3.9: Pin diagram of MAX 232 IC

3.1.7 RS 232(Female Port) RS-232 is the component which is used to connect system (pc) to microcontroller. RS-232 (Recommended Standard 232) is the traditional name for a series of standards for serial binary single-ended data and control signals connecting between a DTE (Data Terminal Equipment) and a DCE (Data Circuit- terminating Equipment). It is commonly used in computer serial ports. The standard defines the electrical characteristics and timing of signals, the meaning of signals, and the physical size and pinout of connectors. RS232 is limited to point-to-point connections between PC serial ports and devices. RS 232 hardware can be used for serial communication up to distances of 50 feet. 3.1.7.1 Voltage levels: The RS-232 standard defines the voltage levels that correspond to logical one and logical zero levels for the data transmission and the control signal lines. For data transmission lines (TxD, RxD and their secondary channel equivalents) logic one is defined as a negative voltage, the signal condition is called marking, and has the functional significance. Logic zero is positive and the signal condition is termed spacing.

Table 3.4: indicating voltage levels for DB 9 connector

31

SMART ENERGY METER

Logic level

Voltage level

1

-10V

0

10V

3.1.7.2 PIN CONFIGURATION

Fig 3.10: DB9 Connector with pinout

3.1.7.3 DB9 INTERFACING WITH MICROCONTROLLER USING MAX 232:

Fig 3.11: DB9 interfacing with microcontroller using MAX 232

32

SMART ENERGY METER

3.1.8 Serial port connector: The microcontroller is connected to the pc via a serial communication port. The serial communication port is a combination of a female port and a male port. The male port is connected to the DB-9 connector connected to the microcontroller while the female port is connected to the serial port of the pc.

Fig 3.12: serial port connector

3.1.9 Design of keypad The keypad used in this project is AT91. A 4x4 matrix keypad requiring eight Input/output ports for interfacing is used. Rows are connected to Peripheral Input/output (PIO) pins configured as output. Columns are connected to PIO pins configured as input with interrupts.

Fig 3.13: 4x4 matrix Keypad

33

SMART ENERGY METER

The internal structure of keypad is as follows:

Fig 3.14: Internal structure of keypad

I/O configuration: Rows are connected to four PIO pins configured as outputs. Columns are connected to four PIO pins configured as inputs with interrupts. The idle state of these pins is high level due to four pull-up resistors. PIO interrupt is generated by a low level applied to these pins (caused by a key pressed). Four additional PIO pins are configured as outputs to send the value of the pressed key to LEDS. Timer Counter Configuration: The Timer Counter is configured in waveform operating mode with RC compare interrupt. The Timer Counter is initialized to be incremented on internal clock cycles. The debouncing time is programmable by initializing the RC compare value according to the clock source selected. A software trigger is used to reset the timer counter and start the counter clock. Interrupt: When a key is pressed, a low level is applied to the pin corresponding to the column associated to the key (pins configured as inputs with

34

SMART ENERGY METER

interrupts). A falling edge applied to a column pin creates a PIO interrupt. Then, the processor executes the PIO interrupt subroutine (debouncing) and comes back to its previous state (in the main program). After debouncing time, a RC compare timer interrupt occurs and the processor then executes the timer interrupt subroutine (decoding the pressed key) and comes back to its previous state (in the main program). Keyboard Operating Sequence To detect a pressed key, the Microcontroller grounds all rows by providing 0 to the output latch, and then it reads the columns. If the data read from the columns isD3- D0=1111 no key has been pressed and the process is continued until a key is detected. However if one of the columns bits is zero this means that a key press has occur. For example if D2-D0=1101 this means that a key in D1 column has been pressed after a key press is detected, the microcontroller will go through the process of identifying the key. Starting with the top row, the microcontroller grounds it by providing a low to row D0 only then it reads the columns. If the data read is all once, no key in that row is achieved and the process is moved to the next row. It ground the next row reads the column and checks for any zero. This process continues until the row is identified. After identification of the row in which the key has been press the next task is to find out which column the pressed key belongs to. This should be easy since the micro control knows at any time which the row and column are being accessed.

3.1.10 IR sensors and IC NE555 Timer: The pair of IR sensors generally constitute of a photo transmitter and a photo receiver. The photo transmitter generally a photo diode emits IR rays while the receiver receives the IR rays. Whenever the transmission is blocked the sensor unit sends a interrupt signal to the microcontroller which then increments the counter. 3.1.10.1 Photo transmitter: The photo transmitters are IR LEDs or photo diodes used to emit light. IR LEDs are just like LEDs which emits IR rays. Since the IR rays are out of the visible range we cannot observe the rays from the transmitter. A photodiode is a type of photo-detector capable of converting light into either current or voltage, depending upon the mode of operation. Photodiodes are similar to regular semiconductor diodes except that they may be either exposed (to detect vacuum UV or X-rays) or packaged with a window or optical fibre connection to allow light to reach the sensitive part of the device. Many diodes designed for use specifically as a photodiode will also use a PIN junction rather than the typical PN junction. 3.1.10.2 Principle of Operation: A photodiode is a PN junction or PIN structure. When a photon of sufficient energy strikes the diode, it excites an electron thereby creating a mobile electron and a

35

SMART ENERGY METER

positively charged electron hole. If the absorption occurs in the junction's depletion region, or one diffusion length away from it, these carriers are swept from the junction by the built-in field of the depletion region. Thus holes move toward the anode, and electrons toward the cathode, and a photocurrent is produced.

3.1.10.2. a Design parameters

1. 2. 3. 4. 5.

Transistor TCRT5000 IR transmitter TCRT5000 IR receiver 100ohms , 220ohms resistor (near transmitter) 22ohms,4.7ohms resister (near receiver)

Fig 3.15: IR Transmitter Circuit diagram

Fig 3.16: IR Receiver Circuit diagram

36

SMART ENERGY METER

3.1.10.3 Applications: Photo diodes are used in  Consumer electronic devices such as compact disc players, smoke detectors, and the receivers for remote controls in VCRs and television.  Accurate measurement of light intensity.  Detectors for computed tomography (coupled with scintillators) or instruments to analyze samples (immunoassay), pulse oximeters.  Optical communications and in lighting regulation.  Astronomy, spectroscopy, night vision equipment and laser range finding. 3.1.10.4 FEATURES:      

λ= 940 nm Chip material =GaAs with AlGaAs window Medium Emission Angle, 40° High Output Power Package material and color: Clear, untinted, plastic Ideal for remote control applications

3.1.10.5 IR Receiver: IR receiver is used to receive the signals transmitted by the IR transmitter.IR receiver is similar to a N-P-N transistor. It is a three terminal device but looks like a two terminal device a base is connected internally. It is a nothing but a phototransistor.

Fig 3.17: IR receiver 3.1.10.6 Phototransistors: Phototransistors also consist of a photodiode with internal gain. A phototransistor is in essence nothing more than a bipolar transistor that is encased in a transparent case so that light can reach the base-collector junction.

3.1.10.7 Principle of Operation: The electrons that are generated by photons in the base-collector junction are injected into the base, and this current is amplified by the transistor operation. Note that although phototransistors have a higher responsiveness for light they are unable to detect low levels of light any better than photodiodes. Phototransistors also have slower response times.

37

SMART ENERGY METER

3.1.11 IC NE555 TIMER: The 555 timer IC is an integrated circuit used in a variety of timer, pulse generation and oscillator applications. The full part numbers were NE555 (commercial temperature range, 0 °C to +70 °C). It has been hypothesized that the 555 got its name from the three 5 kΩ resistors used internally. Depending on the manufacturer, the standard 555 package includes over 20 transistors, 2 diodes and 15 resistors on a silicon chip installed in an 8-pin mini dualin-line package (DIP-8).

Fig 3.18: 555 Timer The 555 has three operating modes: 3.1.11.1 Monostable mode: In this mode, the 555 timer functions as a "one-shot" pulse generator. Applications include timers, missing pulse detection, bounce free switches, touch switches, frequency divider, capacitance measurement, pulse-width modulation (PWM) and so on. 3.1.11.2 Astable mode: Free running mode: the 555 can operate as an oscillator. Uses include LED and lamp flashers, pulse generation, logic clocks, tone generation, security alarms, pulse position modulation and so on. Selecting a NTC as timing resistor allows the use of the 555 in a temperature sensor: the period of the output pulse is determined by the temperature. The use of a microprocessor based circuit can then convert the pulse period to temperature, linearize it and even provide calibration means. 3.1.11.3 Bistable mode or Schmitt trigger: The 555 can operate as a flip-flop, if the DIS pin is not connected and no capacitor is used. Uses include bounce free latched switches.

3.1.11.4 Features of NE555 Timer:     

Timing is from microseconds through hours O/p is compatible with CMOS, DTL and TTL High Temperature Stability Duty cycle is Adjustable Mono-stable and Astable operations

3.1.11.5 Specifications of NE555Timer:

38

SMART ENERGY METER

     

Supply voltage VCC Supply current (VCC=+5V) Maximum O/P Current Power Dissipation Power consumption (minimum operating) Operating temperature

4.5 to 15V 3 to 6mA 200mA 600mA 30mW@ 5V,225mW@15V 0 to 70 C

3.1.12 Resistors: A resistor is a two-terminal ive electronic component that implements electrical resistance as a circuit element. When a voltage V is applied across the terminals of a resistor, a current I will flow through the resistor in direct proportion to that voltage. This constant of proportionality is called conductance, G. The reciprocal of the conductance is known as the resistance R, since, with a given voltage V, a larger value of R further "resists" the flow of current I as given by Ohm's law:

Fig 3.19: Resistors Practical resistors can be made of various compounds and films, as well as resistance wire (wire made of a high-resistivity alloy, such as nickel-chrome). Resistors are also implemented within integrated circuits, particularly analog devices, and can also be integrated into hybrid and printed circuits. 3.1.13 Capacitors: A capacitor (formerly known as condenser) is a device for storing electric charge. The forms of practical capacitors vary widely, but all contain at least two conductors separated by a non-conductor. Capacitors used as parts of electrical systems, for example, consist of metal foils separated by a layer of insulating film.

39

SMART ENERGY METER

A capacitor is a ive electronic component consisting of a pair of conductors separated by a dielectric (insulator). When there is a potential difference (voltage) across the conductors, a static electric field develops across the dielectric, causing positive charge to collect on one plate and negative charge on the other plate. Energy is stored in the electrostatic field. An ideal capacitor is characterized by a single constant value, capacitance, measured in farads. This is the ratio of the electric charge on each conductor to the potential difference between them.

Fig 3.20: capacitors Capacitors are widely used in electronic circuits for blocking direct current while allowing alternating current to , in filter networks, for smoothing the output of power supplies, in the resonant circuits that tune radios to particular frequencies and for many other purposes. The capacitor is a reasonably general model for electric fields within electric circuits. An ideal capacitor is wholly characterized by a constant capacitance C, defined as the ratio of charge ±Q on each conductor to the voltage V between them:

3.1.14 Crystal oscillator: A crystal oscillator is an electronic oscillator circuit that uses the mechanical resonance of a vibrating crystal of piezoelectric material to create an electrical signal with a very precise frequency. This frequency is commonly used to keep track of time (as in quartz wristwatches), to provide a stable clock signal for digital integrated circuits, and to stabilize frequencies for radio transmitters and receivers. The most common type of piezoelectric resonator used is the quartz crystal, so oscillator circuits designed around them became known as "crystal oscillators."

40

SMART ENERGY METER

Fig 3.21: crystal oscillator Quartz crystals are manufactured for frequencies from a few tens of kilohertz to tens of megahertz. More than two billion (2×109) crystals are manufactured annually. Most are used for consumer devices such as wristwatches, clocks, radios, computers, and cell phones. Quartz crystals are also found inside test and measurement equipment, such as counters, signal generators, and oscilloscopes.

3.2 Software design: 3.2.1 Liquid Crystal Display 3.2.1.1 Initializing the LCD Before you using the LCD, the program must initialize and configure it. This is accomplished by sending a number of initialization instructions to the LCD. The first instruction to send is the no of data for the LCD i.e., with an 8-bit or 4-bit data bus. The other thing need to specify is display matrix; in the selected LCD it is a 5x8 dot character font. These two options are selected by sending the command 38h to the LCD as a command. The command can give to the LCD by invoking the pre defined function call lcdcmd with ing parameters value of 38H, the syntax for the same can be given like lcdcmd (0x38). 3.2.1.2 Checking the busy status of the LCD 3.2.1.2.1 Busy Flag (BF): When the busy flag is high or “1” the module is performing an internal operation and the next instruction will not be accepted. The RS=0 is used to check the Busy flag bit too see if the LCD is ready to receive information. The Busy flag is D7 and can be read when R/W = 1 and RS = 0, as follows: if R/W = 1, RS= 0.When D7=1 (busy flag), the LCD is busy taking care of internal operations and will not accept any new information. When D7=0, the LCD is ready to receive new information.

41

SMART ENERGY METER

3.2.1.2.1.1 Busy flag flowchart

Fig 3.22: Busy flag flowchart

3.2.1.2.2.1 Writing command to the Display To give a command to perform some special functions like move to position, clear LCD ,blink the curser etc. the instruction sequence must follow like first instruction must be set in the data bus set RS signal to logic 0 and enabling the LCD will receive the data . After finishing the instruction sequence the application must wait till the LCD completes the instruction by checking the LCD Busy status.

3.2.1.2.2.2 Writing command display flow chart 42

SMART ENERGY METER

Fig 3.23: Writing command display flow chart 1. Check the Busy flag bit 2. Set the instruction in data lines (if it is writing) 3. Set RS bit to logic 1 to 0 4. Set R/W bit is to low 6. Set En line to high 7. Set line to low 3.2.1.2.4.1 Displaying the data in to the LCD Writing the string in the LCD, to get the result first the address at which the string has to display on the screen is given as command followed by displaying the individual characters as LCD data .That finishes the data to be display in the LCD.

The complete flow chart representation of LCD working process is as follows:

43

SMART ENERGY METER

Start

RS=0 RS=0

E=1

Delay E=1 E=0

Delay LCD Busy P0=command

LCD Busy

Fig 3.24: Flow chart for the LCD function.

3.2.2 KEYPAD:

44

SMART ENERGY METER

3.2.2.1 FLOW CHART OF KEY BOARD SCANNING ALGORITHM

Fig 3.25: Flow Chart of Key Board Scanning Algorithm

45

SMART ENERGY METER

COMPLETE FLOW CHART OF SMART ENERGY METER

46

SMART ENERGY METER

CHAPTER - 4

47

SMART ENERGY METER

CHAPTER – 4 IMPLEMENTATION

4.1 HARDWARE IMPLEMENTATION 4.1.1 Complete Schematic of Smart Energy Meter

Fig 4.1: Complete schematic of Smart Energy Meter

48

SMART ENERGY METER

4.1.2 Connections of P89C51RD2FN The pin configuration of P89C51RD2XX:-

Fig 4.2: Pin diagram of P89C51RD2FN In this project the microcontroller is connected to MAX232, LCD, Keypad, sensors. The connections of microcontroller are given briefly below:  Pin1 to pin8 (Port 0) of controller are connected to the data lines of keypad (D0-D8).  The reset pin is connected to the 9th pin (RST) of P89C51RD2FN, as it is used for set reset the program.  While the 10pin is connected to the 12th pin of MAX232.  11th pin of controller is connected to the 11th pin of MAX232.  The interrupt given by the IR sensors from the 555IC timer should be connected to the 12th pin i.e. INTO pin of controller.  13th pin is used as an external interrupt, but here in this project there is no use with this pin.  The crystal oscillator which gives a frequency of 11.0592 MHz for the required Baud rate of 9600Hz to the microcontroller. This crystal oscillator is

49

SMART ENERGY METER

  

 



connected in between 18th (XALT 1) and 19th (XALT 2) pins of P89C51RD2FN controller. The 20th pin of controller is grounded. The pins from 21st to 28th (port 2 data lines) are used for the external peripheral connections. The 29th pin is connected to an on-off switch so as to dump and execute the program. Whenever the PSEN pin is connected to ground then we can execute the last dumped program, likewise when 29th pin is connected to VCC then code can be dumped into the controller. Address Latch Enable pin (30th pin) of controller is connected to the ground hence no connections need not to be given to this pin. External Access Enable or programming supply voltage should be latched when RST is released and any subsequent changes have no effect. This pin also receives the programming supply voltage (VPP) during Flash programming. Hence the pin 31st must be connected to high i.e. VCC. Port0 (pins 32 to 39) are connected to LCD in this project. But these should be connected to other peripherals through pull up resistors.

4.1.3 Pin connections of LCD The LCD used for output display is JHD162A series. The detailed connections of LCD is described briefly as

 The 1st and 2nd pins of JHD162A LCD are connected to ground and high voltage VCC respectively.  3rd pin of LCD is connected to the centre pin of the potentiometer or variable resistor so as to adjust the contrast of LCD.  The 4th, 5th, 6th pins are connected to 26th (P 2.5), 27th (P 2.6), 28th (P 2.7) pins of the microcontroller respectively.  The 7th to 14th pins are data pins and are connected to the 39th (P 0.0) to 32nd (P 0.7) pins of the microcontroller respectively.  The 15th and 16th pins are used for backlight purpose. 15th pin is connected to VCC and 16th pin to ground.

50

SMART ENERGY METER

Fig 4.3: connection of LCD with P89C51RD2FN.

4.1.4 KEYPAD CONNECTIONS:   

The keypad used is 4*4 keypad The pins 1, 2, 3, 4 which are connected to columns of the keypad are connected to 1, 2, 3, 4(P1.0 to P1.3) pins of the microcontroller respectively. The pins 5, 6, 7, 8 which are connected to rows of the keypad are connected to 5, 6, 7, 8(P1.4 to P1.7) pins of the microcontroller respectively.

4.1.5 MAX232 AND DB9 CONNECTION: MAX232 and DB9 connector plays a key role in program dumping and communication between project kit to the PC host.  

 

Capacitor C10 of capacitance 1Uf is connected across 1st and 3rd pins of MAX232 and C9 of capacitance 1Uf is connected in between 4th and 5th pins. Charge pump capacitors are required for the MAX232 to work it as voltage level shifter. The charge pump capacitors used here are C7 and C8 whose capacitance is 1Uf. C7 is connected between 6th pin and ground, while C8 is connected across 2nd pin of MAX232 and Vcc. 12th and 11th pins of MAX232 are connected to the 10th and 11th pins of P89C51RD2FN controller respectively. These acts as a transmitter and receiver for the data flow. To connect the MAX232 to the PC host we require a medium named as DB9 connector. The 2nd and 3rd pin of the DB9 connector should be connected to the 14th and 13th pins of MAX232 respectively. While the 5th pin is grounded.

51

SMART ENERGY METER

4.1.6 IC555 TIMER and IR transmitter connections: 

The sensor is designed using a 555 timer, a IR transmitter and a IR receiver.  The 555 timer is operated in astable mode of operation.  The 1st pin is grounded.  The 2nd pin and 6th pin are shorted, 2nd pin is connected to VCC through the 10K and 220K pot, IR receiver is connected to 2nd pin in reverse bias.  The pin 3 of 555 timer is an output pin which is connected to the 12th pin (P 3.2) of the microcontroller.  The 4th pin and 8th pin are shorted, 8th pin is connected to VCC and 0.1µf capacitor is connected between 8th pin and ground.  The 5th pin is grounded through 0.01µf capacitor.  The IR transmitter is connected between VCC and ground through 270 ohm resistor. It is connected in forward bias.  If there is obstruction between transmitter and receiver, the receiver output gives 3V to 5V.  Whenever there is an obstruction of current between transmitter and receiver, the current ed to receiver decreases and hence the voltage across voltage divider decreases. As a result a short pulse is applied to the port pin of the 8051 microcontroller. On receiving a pulse from the sensor circuit, the controller increments the counter which indicates the consumption of electricity. The IR sensor implementation using 555 timer is shown in figure below:

Fig 4.4: connection of IR sensors with 555 timers.

52

SMART ENERGY METER

CHAPTER - 5

53

SMART ENERGY METER

CHAPTER-5 SOFTWARE IMPLEMENTATION This chapter explores some real world applications of the P89C51RD2xx, and also includes how to interface the P89C51RD2xx to devices such as an LCD and a keyboard and its software functionality using embedded C language.

5.1 JHD162A LCD INTERFACING 5.1.1Initializing the LCD Before you using the LCD, the program must initialize and configure it. This is accomplished by sending a number of initialization instructions to the LCD. The first instruction to send is the no of data for the LCD i.e., with an 8-bit or 4-bit data bus. The other thing need to specify is display matrix; in the selected LCD it is a 5x8 dot character font. These two options are selected by sending the command 38h to the LCD as a command. The command can give to the LCD by invoking the pre defined function call lcdcmd with ing parameters value of 38H ,the syntax for the same can be given like lcdcmd(0x38). 5.1.2 The initialization sequence code can be given as follows:

lcdcmd(0x38); // 2 lines and 5x7 matrix lcdcmd(0xC0); // force cursor to begging of 2nd line lcdcmd(0x0E); // display on, cursor blinking lcdcmd(0x01); //clear display screen lcdcmd(0x06); // increment cursor (shift cursor right) lcdcmd(0x80); // force cursor to begging of 1st line

5.1.3 Checking the busy status of the LCD Busy Flag (BF): void lcdready(void) { busy=1; rs=0; // select command rw=1; while(busy==1) // if Bit (D7) high, LCD still busy { en=0; // Finish the command MSDelay(1); en=1; // Start LCD command 54

SMART ENERGY METER

} } 5.1.4 Writing command to the Display void lcdcmd (unsigned char value) // LCD command initiation routine { Lcdready(); // wait till the LCD executes the instruction ldata=value; // Set the value(instruction) in Data bus rs=0; // select as command rw=0; en=1; // set the enable command MSDelay(1); en=0; // Reset the enable command } 5.1.5 Writing Data to Display void lcddata (unsigned char value) // LCD data placing routine { lcdready(); // wait till the LCD executes the instruction ldata = value; // Set the value(Data) in Data bus rs=1; // select as data rw=0; //read command en=1; // Send Enable Signal to LCD MSDelay(1); // This Function Gives Approximate Delay required For LCD Initialization en=0; //Reset the Enable Command } 5.1.6 Displaying the data in to the LCD void WriteString(unsigned char count,unsigned char *MSG) { unsigned char i; for(i=0;i
c0=P1^4; c1=P1^5; c2=P1^6; c3=P1^7;

//keypad columns

55

SMART ENERGY METER

unsigned char KeyTest(void) { P1=0xF0; while (1) { while(P1!=0xF0) { r0=0; r1=1;r2=1;r3=1; if(c0==0) return '1'; else if(c1==0) return '4'; else if(c2==0) return '7'; else if(c3==0) return 'E'; r1=0; r0=1;r2=1;r3=1; if(c0==0) return '2'; else if(c1==0) return '5'; else if(c2==0) return '8'; else if(c3==0) return '0'; r2=0; r0=1;r1=1;r3=1; if(c0==0) return '3'; else if(c1==0) return '6'; else if(c2==0) return '9'; else if(c3==0) return 'F'; // Down Arrow r3=0; r0=1;r1=1;r2=1; if(c0==0) return 'A'; else if(c1==0) return 'B'; else if(c2==0) return 'C'; // Redail else if(c3==0) return 'D'; // Enter }}} 5.1.8 SENSORS: sbit sense=P3^2; //energy meter void _Up() interrupt 0

56

SMART ENERGY METER

{ Flag=sense; if(Flag==1) { Count++; Flag=0; } }

57

SMART ENERGY METER

CHAPTER - 6

Chapter – 6 58

SMART ENERGY METER

DEBUGGING TECHNIQUES

6.1 Keil uvision Debugger 6.1.1 Introduction to Keil IDE Keil is a compiler that has 3 windows, project window, edit window, and build or command window Schematic. Today, Keil Software provides a broad range of development tools for the embedded systems marketplace. Their products include ANSIC compilers, macro assemblers, debuggers, linkers, library managers, and real-time operating systems. . It was then that Keil Software implemented the first C compiler designed from the ground-up specifically for the 89C51 microcontroller.

6.1.2 Features 1. Nine basic data types, including 32-bit IEEE floating-point 2. Flexible variable allocation with bit, data, bdata, idata, xdata, and pdata memory types 3. Interrupt functions may be written in C 4. Full use of the 8051 banks 5. Complete symbol and type information for source-level debugging 6. Bit-addressable data objects 7. Built-in interface for the RTX51 real-time kernel 8. for dual data pointers on Atmel, AMD, Cypress, Dallas semiconductor, Infineon, Philips, and Transcend microcontrollers 9. for Phillips 8xC510,8xC71,and 8xC752 limited instruction sets 10. for the Phillips 80C51 arithmetic unit.

The Keil 8051 Development Tools are designed to solve the complex problems facing embedded software developers.   

When starting a new project, simply select the microcontroller you use from the Device Database and the µvision IDE sets all compiler, assembler, linker, and memory options for you. Numerous example programs are included to help you get started with most popular embedded 8051 devices. The Keil µVision Debugger accurately simulates on-chip peripherals (CAN, UART, SPI, Interrupts, I/O Ports, A/D Convertor, D/A convertor, and PWM Modules) of your 8051 device. Simulation helps you understand hardware configurations and avoids time wasted on setup problems. Additionally, with

59

SMART ENERGY METER



simulation, you can write and test applications before target hardware is available. When you are ready to begin testing your software application with target hardware, use the MON51, MONADI, or FlashMON51 Target Monitors, the ISD51 In-system Debugger, or the ULINK USB-JTAG Adapter to and test program code on your target system.

6.1.3 Steps to follow while writing a program in keil: 1. Install Keil Micro Vision in your PC, Then after Click on that “Keil UVision” icon. After opening the window go to toolbar and select Project Tab then close previous project. 2. Next select New Project from Project Tab. 3. Then it will open “Create New Project” window. Select the path where you want to save project and edit project name. 4. Next it opens “Select Device for Target” window, it shows list of companies and here you can select the device manufacturer company. 5. For an example, for your project purpose you can select the chip as 89c51rd2xx from Philips Group. Next Click OK Button, it appears empty window here you can observe left side a small window i.e., “Project Window”. Next create a new file. 6. From the Main tool bar Menu select “File” Tab and go to New, then it will open a window, there you can edit the program. 7. Here you can edit the program as which language will you prefer either Assembly or C. 8. After editing the program save the file with extension as “.c” or “.asm”, if you write a program in Assembly Language save as “.asm” or if you write a program in C Language save as “.c” in the selected path. 9. Then after saving the file, compile the program. For compilation go to project window select “source group” and right click on that and go to “Add files to Group”. 10. Here it will ask which file has to add. For an example here you can add “test.c” as you saved before 11. After adding the file, again go to Project Window and right click on your “c file” then select “Build target” for compilation. If there is any “Errors or Warnings” in your program you can check in “Output Window” that is shown bottom of the Keil window. 12. Here in this step you can observe the output window for “errors and warnings 13. If you make any mistake in your program you can check in this slide for which error and where the error is by clicking on that error

60

SMART ENERGY METER

14. After compilation then next go to Debug Session. In Tool Bar menu go to “Debug” tab and select “Start/Stop Debug Session”. 15. Write a program for “Leds Blinking”. LEDS are connected to PORT-1. you can observe the output in that port. 16. To see the Ports and other Peripheral Features go to main toolbar menu and select peripherals. 17. In this slide see the selected port i.e., PORT-1. 18. Start to trace the program in sequence manner i.e, step by step execution and observe the output in port window 19. After completion of Debug Session Create an Hex file for Burning the Processor. Here to create a Hex file goes to project window and right click on Target next select “Option for Target”. 20. It appears one window; here in “target tab” modify the crystal frequency as you connected to your microcontroller. 21. Next go to “Output‟ tab. In that Output tab click on “Create HEX File” and then click OK. 22. Finally Once again compile your program. The Created Hex File will appear in your path folder

6.2 Flash magic Flash Magic is a PC tool for programming flash based microcontrollers from NXP using a serial or Ethernet protocol while in the target hardware. 6.2.1 Features  Straightforward and intuitive interface  Read any section of Flash and save as an Intel Hex file.  Program security bits  Automatic ing after programming  Five simple steps to erasing and programming a device and setting key options  Fills unused Flash to increase firmware security  Check which Flash blocks are blank or in use with the ability to easily erase all blocks in use  Reprogram the Boot Vector and Status Byte with the help of confirmation features that prevent accidentally programming incorrect values.

61

SMART ENERGY METER

 Display the contents of Flash in ASCII and Hexadecimal formats  Single-click access to the manual, Flash Magic home page and NXP Microcontrollers home page  Use high-speed serial communications on devices that it.  Command Line interface allowing use in IDEs and Batch Files.  s half-duplex communications for many devices  Hex Files previously programmed  Control the DTR and RTS RS232 signals to place the device into Boot ROM and Execute modes automatically (requires hardware )  Send commands to place the device in Boot loader mode  Powerful, flexible Just In Time Code feature. Write your own JIT Modules to generate last minute code for programming, for example serial number generation.  Displays information about the selected Hex File, including the creation and modification dates, flash memory used, percentage of the current device used  Read the device signature  Build your own Flash Magic based applications using the DLLs for C, C++, Python  Build your own Flash Magic based applications using .NET languages (Windows only)

6.3 Null MODEM checking (Hyper Terminal) Debugging of 8051 application can be very easy if we able to send debug information to serial port of PC. And its output can be seen on HyperTerminal (in Windows ) or Minicom ( in Linux ). We can display content of any variable, memory location etc. We can also print other useful information on serial terminal which could replicate the flow of the code.

The Microsoft HyperTerminal terminal emulation application can display messages sent from the serial port of a SDB or hardware platform. You can use these messages to whether the boot loader is on the SDB, to discover problems that may occur when the SDB boots, and to obtain the name of the SDB for use in the Platform Builder integrated development environment (IDE). To configure HyperTerminal for BSPs 1. From the Windows Start menu, choose Accessories.

choose All Programs,

and

then

62

SMART ENERGY METER

2. Choose Communications, and then choose HyperTerminal. 3. In the Connection Description dialog box, in the Name box, type a name for the connection to your SDB. 4. From the Icon list, choose an icon to represent your connection, and then choose OK. 5. In the Connect To dialog box, in the Connect using box, choose the communications (COM) port on the development workstation through which you want to receive messages from the SDB. The COM port that you choose must be the COM port on the development workstation to which you attach the null modem cable. 6. Choose OK. 7. In the COM Properties dialog box, modify the settings for your connection so that the settings are correct for your BSP.

6.4 Hardware debugging techniques In the context of hardware debugging techniques, we are going to observe the different types of error and checking of the components in the project. While considering the microcontroller, the voltage level at 30th pin must be 1.6V because of the following reason 1. The voltage supply to the kit or mainly processor is 5V. 2. The duty cycle of the microcontroller is 33% Duty Cycle = T on / (T on+T off) Where T off = 2* T on DC = 1/ (1+2) DC= 0.333 Hence the voltage at 30th pin should be product of Duty Cycle and voltage supply VCC. Therefore the voltage should be 1.6V. 3. The voltage levels at 2nd and 6th pins of MAX232 should be -10V and +10V respectively.

CONCLUSION Since the inception of electricity deregulation and market-driven pricing throughout the world, utilities have been looking for a means to match consumption with generation. Smart meters are also believed to be a less costly alternative to traditional interval or time-of-use meters and are intended to be used on a wide scale with all customer classes, including residential customers ing Consumers: a) An end to estimate bills, which are a major source of complaints for many customers b)A tool to help consumers better manage their energy use - smart meters with a display can provide up to date information on electricity consumption in the currency of that country and in doing so help people to

63

SMART ENERGY METER

better manage their energy use and reduce their energy bills and carbon emissions .c) voltage levels, and power events can be tracked and logged across the entire customer base. s Power Grid: The Ability to remotely turn power on or off to a customer, read usage information from a meter, detect a service outage, detect the unauthorized use of electricity, know the maximum amount of electricity that a customer can demand at any time. It is projected to reduce the staff required to read meter data across the customer base. s Environment: The billing is through HyperTerminal or GSM, so lot of paper can be saved .So Cutting of Trees can be avoided . It is believed that billing customers by time of day will encourage consumers to adjust their consumption habits to be more responsive to market prices thereby saving the power by which natural resources are protected. It is a Greener, Smarter, New era of Energy Use.

RESULTS Now the most awaited part of the program is final result which can be seen by the following steps once the kit is ready.     

Give 5V Power supply and connect the pc with serial connector to DB9 connector Now ON the circuit. We can see on the LCD display “WELCOME RMCE” “SMART ENERGY METER” and press enter (E) in keypad. The LCD asks for id and . Once they are correct, it shows “AUTHENTICATED”. Now main menu is displayed having options:1.Readings 2. Settings      

If 1 is pressed the LCD displays initial count value as 0000 When one interrupt is detected, go to readings and then the count value is incremented. Then 2 options will be displayed:1.Send 2.Exit If 1 is pressed, the data i.e. count value and unit price will be displayed on the PC through HyperTerminal. Once data is sent, we will get a reply “DATA SENT”. If option 2 is pressed i.e. SETTINGS we can change „ ID, and UNIT PRICE AND PHONE NO”. But it can be changed only by the only.

7. BIBILOGRAPHY:

64

SMART ENERGY METER

 Janci Gillespie Mazidi, Muhammad Ali Mazidi, The 8051 micro controller and embedded systems, PHI Prentice hall India, Eastern Economy Edition, www.phindia.com. 

Kenneth J. Ayala, The 8051 Microcontroller, architecture, Programming and Applications, Pen ram international publishing Pvt. Ltd. 1996



Arnold S. Berger, Embedded systems design, an introduction to process, tools, and Techniques, CMP Books, 2005. www.cmpbooks.com

 

Yashvant Kanetkar, Let Us C, BPB Publications, 1999 www.bpbpub.com Dreamtech Software Team, Programming for Embedded systems, WILEY Publishing, Inc, 2003.



http://en.wikipedia.org/wiki/Level_s

65

SMART ENERGY METER

APPENDICES KEIL MICRO VISION IDE Keil is a compiler that has 3 windows, project window, edit window, and build or command window Schematic. Today, Keil Software provides a broad range of development tools for the embedded systems marketplace. Their products include ANSIC compilers, macro assemblers, debuggers, linkers, library managers, and realtime operating systems. Steps to follow while writing a program in keil:

1. 2.

Click on the Keil Vision Icon on Desktop The following fig will appear

3. 4.

Click on the Project menu from the title bar Then Click on New Project

66

SMART ENERGY METER

5.

Save the Project by typing suitable project name with no extension in u r own folder sited in either C:\ or D:\

6. 7. 8.

Then Click on Save button above. Select the component for u r project. i.e. NXP…… Click on the + Symbol beside of NXP

67

SMART ENERGY METER

9.

Select P89C51RD2XX as shown below

10. 11.

Then Click on “OK” The Following fig will appear

12. 13.

Then Click either YES or NO………mostly “YES”. Now your project is ready to USE.

68

SMART ENERGY METER

14.

Now double click on the Target1, you would get another option “Source group 1” as shown in next page.

15.

Click on the file option from menu bar and select “new”.

69

SMART ENERGY METER

16.

The next screen will be as shown in next page, and just maximize it by double clicking on its blue boarder.

17. 18.

Now start writing program in either in “EMBEDDED C” or “ASM”. For a program written in Assembly, then save it with extension “. asm” and for “EMBEDDED C” based program save it with extension “ .C”

70

SMART ENERGY METER

19.

Now right click on Source group 1 and click on “Add files to Group Source”.

20.

Now you will get another window, on which by default “EMBEDDED C” files will appear.

21.

Now select as per your file extension given while saving the file

71

SMART ENERGY METER

22.

Click only one time on option “ADD”.

23.

Now Press function key F7 to compile. Any error will appear if so happen.

24.

If the file contains no error, then press Control+F5 simultaneously.

72

SMART ENERGY METER

25.

The new window is as follows

26. 27.

Then Click “OK”. Now click on the Peripherals from menu bar, and check your required port as shown in fig below.

73

SMART ENERGY METER

28.

Drag the port a side and click in the program file.

29. 30.

Now keep Pressing function key “F11” slowly and observe. You are running your program successfully.

FLASH MAGIC: Flash Magic is a PC tool for programming flash based microcontrollers from NXP using a serial or Ethernet protocol while in the target hardware. The steps for while using Flash Magic 1) Click on the flash magic icon on the desktop.

74

SMART ENERGY METER

2) The below figure will appear

3) Select the device as P89C51RD2XX.

75

SMART ENERGY METER

4) To check whether the device is connected or not. Click on ISP + “Read device signature”.

5) Then the device signature will be shown

6) Then by browsing the required HEX file we can dump the code into controller by pressing “START” button.

76

SMART ENERGY METER

Setup of HyperTerminal

Go to 1. Start Menu>> Programs >> Accessories >> Communications >> Hyper Terminal After that HyperTerminal window will open. If it prompt for checking of default program as shown in fig, then say yes to it.

2. Click Yes 3. Type Connection Name as 8051 (or as per your Choice)

77

SMART ENERGY METER

4. Select COM PORT (1, 2, 3 etc) whichever is available. TO Serial Converters as Reliable) So use Standard Serial Port

(NOTE: Very Less USB-

5. Do Port Setting as Given Below.

Then Click Apply and OK.

78

SMART ENERGY METER

6. Now you See Bottom Left side It shows “Connected”.

7. Now burn the Hex File (Given) and Switch on the Circuit after Connecting Specified Serial Port .You will see output as Follows:

If everything works fine you will see Hello World on the screen. Otherwise check your setup.

79

SMART ENERGY METER

COMPLETE CODE: The complete source code for the project entitled as “Smart Energy Meter” using Hyper Terminal is given below. #include sbit r0=P1^0; sbit r1=P1^1; sbit r2=P1^2; sbit r3=P1^3; //rows sbit c0=P1^4; sbit c1=P1^5; sbit c2=P1^6; sbit c3=P1^7; //columns sbit sense=P3^2; //energy meter sfr ldata=0x80;//port 0 address sbit rs=P2^5; sbit rw=P2^6; sbit en=P2^7; //control pins of lcd sbit busy=P0^7; //busy pin of lcd void UpdateService(void); void lcdcmd(unsigned char); void lcddata(unsigned char); void lcdready(void); void MainMenu(void); void MSDelay(unsigned int); void WriteString(unsigned char,unsigned char *); void serialinit(void); void sertx(unsigned char); void sendintdata(unsigned int); void SendString(unsigned char,unsigned char * );

80

SMART ENERGY METER

unsigned char KeyTest(void); unsigned char key; unsigned char mode; void Start(void); void LCDClear(void); unsigned char MY_PWD[4]={'1','2','3','4'}; unsigned int Count; unsigned char Flag; //void convertanddisplay(unsigned char value); void _Up() interrupt 0 { Flag=sense; if (Flag==1) { Count++; Flag=0; } } void lcdcmd (unsigned char value) { lcdready(); ldata=value; rs=0; rw=0; en=1; MSDelay(1); en=0; } void lcddata (unsigned char value)

81

SMART ENERGY METER

{ lcdready(); ldata=value; rs=1; rw=0; en=1; MSDelay(1); en=0; } void lcdready(void) { busy=1; rs=0; rw=1; while(busy==1) { en=0; MSDelay(1); en=1; } }

void MSDelay(unsigned int Iter) { unsigned int i, j; for(i=0;i
82

SMART ENERGY METER

} void WriteString(unsigned char count,unsigned char *MSG) { unsigned char i; for(i=0;i
83

SMART ENERGY METER

} void sendintdata(unsigned int p) { unsigned int temp; temp=p; sertx(temp/1000+0x30); temp=temp%1000; sertx(temp/100+0x30); temp=temp%100; sertx(temp/10+0x30); sertx(temp%10+0x30); } unsigned char KeyTest(void) { P1=0xF0; while (1) { while(P1!=0xF0) { r0=0; r1=1;r2=1;r3=1; if(c0==0) return '1'; else if(c1==0) return '2'; else if(c2==0) return '3'; else if(c3==0) return 'A'; r1=0; r0=1;r2=1;r3=1;

84

SMART ENERGY METER

if(c0==0) return '4'; else if(c1==0) return '5'; else if(c2==0) return '6'; else if(c3==0) return 'B'; r2=0; r0=1;r1=1;r3=1; if(c0==0) return '7'; else if(c1==0) return '8'; else if(c2==0) return '9'; else if(c3==0) return 'C'; // Down Arrow r3=0; r0=1;r1=1;r2=1; if(c0==0) return 'E'; else if(c1==0) return '0'; else if(c2==0) return 'F'; // Redail else if(c3==0) return 'D'; // Enter } } }

85

SMART ENERGY METER

// update service void UpdateService(void) { unsigned int Temp; Temp=0; key=0; while(1) { if(Temp!=Count) { MSDelay(50);

// Intentional Delay of 0.1mSec.

Temp=Count; LCDClear(); lcdcmd(0x80); WriteString(11,"Total units:"); lcddata(Temp/1000+0x30); Temp=Temp%1000; lcddata(Temp/100+0x30); Temp=Temp%100; lcddata(Temp/10+0x30); lcddata(Temp%10+0x30); lcdcmd(0xc0); WriteString(13,"1.send 2.exit"); do { key=KeyTest(); } while(key!='1'&&key!='2'); switch(key)

86

SMART ENERGY METER

{ case '1': { SendString(26,"\r\ncustomer no:9491327686\r\n"); SendString(10,"units are:"); sendintdata(Count); LCDClear(); lcdcmd(0x80); WriteString(9,"data send"); lcdcmd(0xC0); WriteString(4,"1:ok"); do { key=KeyTest(); } while(key!='1'); MainMenu(); break; } case '2': { MainMenu(); break; } } } } } void MainMenu(void)

// Start of project

87

SMART ENERGY METER

{ unsigned char key; unsigned char mode; // unsigned char Sensor, Data[3]; key=0; //

Sensor=0;

/*do { key=KeyTest(); } while(key!='E');*/ LCDClear(); lcdcmd(0x80); LCDClear(); WriteString(10,"1. Reading"); lcdcmd(0xC0); WriteString(11,"2. settings"); do { key=KeyTest(); } while(key!='1'&&key!='2'); switch(key) { case '1': { //Count=0; LCDClear(); lcdcmd(0x80);

88

SMART ENERGY METER

//void Init_GSM(); /* Sensor=MyData; Data[0]=(Sensor/100)+0x30; Sensor=Sensor%100; Data[1]=(Sensor/10)+0x30; Data[2]=(Sensor%10)+0x30; if(((Data[0]+(Data[1]*10))+Data[2])<30) WriteString(3,Data);*/ WriteString(6,"units:"); lcddata(Count/1000+0x30); Count=Count%1000; lcddata(Count/100+0x30); Count=Count%100; lcddata(Count/10+0x30); lcddata(Count%10+0x30); lcdcmd(0xc0); WriteString(16,"press 2 to Exit:"); UpdateService(); MainMenu(); break; } case '2': { LCDClear(); lcdcmd(0x80); WriteString(14,"1.Rs/Unit 2.ID"); lcdcmd(0xC0); WriteString(13,"3.pwd 6.ph no"); do

89

SMART ENERGY METER

{ key=KeyTest(); } while(key!='1'&&key!='2'&&key!='3'&&key!='6'); mode=key; switch(key) { case '1': LCDClear(); lcdcmd(0x80); WriteString(16,"Rs Per Unit=3.50"); lcdcmd(0xC0); WriteString(15,"1:change 2:exit"); do { key=KeyTest(); } while(key!='1'&&key!='2'); switch(key) { case '1': Start(); break; case '2': MainMenu(); break; }; break; case '2':

90

SMART ENERGY METER

LCDClear(); lcdcmd(0x80); WriteString(15,"Change ID:"); lcdcmd(0xC0); WriteString(15,"1:change 2:exit"); do { key=KeyTest(); } while(key!='1'&&key!='2'); switch(key) { case '1': Start(); break; case '2': MainMenu(); break; } case '3': LCDClear(); lcdcmd(0x80); WriteString(11,"Pwd is 1234"); lcdcmd(0xC0); WriteString(15,"1:change 2:exit"); do { key=KeyTest(); }

91

SMART ENERGY METER

while(key!='1'&&key!='2'); switch(key) { case '1': Start(); break; case '2': MainMenu(); break; } break; case '6': LCDClear(); lcdcmd(0x80); WriteString(16,"Ph no:9491327686"); lcdcmd(0xC0); WriteString(15,"1:change 2:exit"); do { key=KeyTest(); } while(key!='1'&&key!='2'); switch(key) { case '1': Start(); break; case '2': MainMenu();

92

SMART ENERGY METER

break; } break; } } } } void Start(void) { unsigned char key; unsigned char uid[4],loop,pwd[4]={'0','0','0','0'}; key=0x00; /* do { key=KeyTest(); } while(key!='E');

// wait for enter. */

LCDClear(); WriteString(8," ID:"); loop=0; do { key=KeyTest(); if(key>='0' && key<='9') { uid[loop]=key; lcddata(key); loop++; MSDelay(100);

93

SMART ENERGY METER

} } while(loop!=4); lcdcmd(0xC0); WriteString(9,":"); loop=0; key=0; do { key=KeyTest(); if(key>='0' && key<='9') { pwd[loop]=key; lcddata('*'); MSDelay(100); loop++; } } while(key!='E'); LCDClear(); if((pwd[0]==MY_PWD[0])&& (pwd[1]==MY_PWD[1])&& (pwd[2]==MY_PWD[2])&& (pwd[3]==MY_PWD[3])) { WriteString(15,"Authenticated!!"); MSDelay(50); MainMenu(); }

94

SMART ENERGY METER

else { WriteString(16,"Access Denied!!!"); lcdcmd(0xC0); WriteString(15,"1:change 2:exit"); do { key=KeyTest(); } while(key!='1'&&key!='2'); switch(key) { case '1': Start(); break; case '2': MainMenu(); break; } } } void LCDClear(void) { lcdcmd(0x0E); lcdcmd(0x01); lcdcmd(0x06); lcdcmd(0x80); } void main(void)

95

SMART ENERGY METER

{ IE=0x81; sense=1; Flag=0; Count=0; serialinit(); lcdcmd(0x38); lcdcmd(0x0E); lcdcmd(0x01); lcdcmd(0x06); lcdcmd(0x80); //MyData=0xFF; WriteString(16,"Welcome ECE@MVSR"); lcdcmd(0xC0); WriteString(16,"SMART ENERGY Mtr"); //Start(); MSDelay(10); MainMenu(); }

96