Waterproofing 4m2g48

Waterproofing Membranes

Preparation and application guidelines

Products

Page

At air temperatures below +4°C measures should be taken to ensure that all surfaces are free from ice or frost. Some waterproofing membranes also act as gas membranes, please also check the Groundwork Engineering section. Horizontal application - the membrane must be applied to smooth prepared substrate. Concrete blinding is preferred but a well rolled granular fill with a compacted sand blinding is acceptable. The substrate shall be free from loose aggregate or other sharp protrusions. Standing water must be removed to prevent contamination of overlaps and subsequent compromise of waterproof properties. Vertical application - the membrane is applied to formwork or ading structures.

Proofex Proofex Engage Proofex Hydromat

3 4 4

Bituthene Preprufe Hydroduct

5 6 7

Sheetseal Double Drain Plaster Drain Cavity Drain Structureseal B U I L D I N G

8 9 9 9 10

P R O D U C T S

Plasprufe

11

Bitusheet Dual Seal Walldrain Slabdrain

12 13 13 13

Membrane installation Cut the membrane to a convenient length for installation. Carefully align the membrane and roll it out with the ribbed surface uppermost. Lay adjacent sheets accurately so they overlap the previous sheet 75mm along the self adhesive edge. When laying adjacent full rolls there should be a stagger of half a roll length to avoid a build up of end ts in one area. End ts and cut edges - butt the sheets onto a detail strip. The top surface of the can be further sealed with a liquid membrane and reinforced with mesh. This overseal should extend 75mm either side of the formed t. All overlaps and ts should be firmly rolled to ensure complete adhesion between layers. WWW.SU PPORTSITE.CO.U K

Waterproofing



Waterproofing

Waterproofing Membranes If cold or damp conditions prevail the self edge adhesive may be made tackier by wiping with a solvent. Detail Strip may be gently warmed with a slack flamed gas torch or heat gun to remove moisture and promote initial adhesion in cold conditions. This procedure may also be used to assist bending the membrane through 90 degrees at the floor to wall junction. Membrane Protection Boards Protection Boards are a tough, flexible bitumen impregnated cellulose board used for the protection of waterproof membranes against mechanical damage, pedestrian or vehicular traffic and abrasion caused by backfilling. The board is resistant to water, ground salts and most corrosive chemicals. They should be butt ted and ed during backfilling. Membrane mastic, mastic tape or adhesive can be used to spot bond the board to the membranes. The ts should be staggered and also staggered over the membrane laps. Primer All surfaces except those below ground bearing slabs and membranes should be primed with one coat of Primer applied at a rate of approx. 10m per litre. A one part bituminous solution for brush or spray application. Apply by clean brush or spray to the clean dry concrete surface. Apply evenly and avoid pooling and over application. Allow to dry before laying the membrane. 2

a Bitumen Polymer Adhesive and is faced with a release sheet. Adhesive Tape Tape is a double-sided and self adhesive and designed to be used in conjunction with the Protection Boards to adhere it to dry surfaces of membranes. It may be used in ‘pads’ 150mm square, or in strips of suitable length. It can also be used to adhere to other materials, such as polyethylene sheets or similar and to most ‘dried’ membranes. Detailing The sheet membrane on its own does not offer the complete waterproofing system. To ensure watertight results, details like pipe penetration, up stands and coves have to be dealt with. Each manufacturer deals with these in a different manner and which may involve liquids or granules. Bentonite Granules A high swelling sodium bentonite in granular form which reacts when in with water and forms an impervious gel, used in conjunction with Waterproofing Membranes to form a fillet at wall to floor transitions and penetrations through horizontal surfaces.

Reinforcing Tape Self Adhesive Reinforcing Tape comprises of a cross-laminated highdensity polyethylene sheet coated with

F O C U S , S P E C I A L I SAT I O N A N D S E R V I C E

3

Waterproofing Membranes Proofex

3000

Proofex 3000 Proofex 3000 is a high performance self-adhesive membrane for a range of waterproofing applications including basements and substructures. Proofex 3000 provides a vapour and waterproof membrane to water excluding structures and protects concrete from attack by aggressive ground salts.

Proofex Type 3000

Width 1m

Length 20m

Roll Area 20m2

Edge Laps 50mm min

End Laps 150mm min

Ancillaries Proofex LM Two component bituminous liquid membrane for waterproofing of underground structures and intricate details in conjunction with Proofex waterproofing systems. Proofex LM Size 28kg pack

Cavitydrain A high-density polyethylene drained cavity former for waterproofing of substructures. Cavitydrain Type Cavitydrain

Size 0.97 x 50m rolls

Fixings Approx 60 per roll

Sheetdrain A geocomposite HDPE drainage sheet with thermobonded polypropylene filter. Sheetdrain Thickness 8mm 16mm

Roll Width 1.1m 1.1m

Roll Length 25m 25m

WWW.SU PPORTSITE.CO.U K

4


Waterproofing

Proofex Engage Engage | LM | LM Mesh Proofex Engage Proofex Engage is a pre-applied waterproofing membrane which mechanically bonds to poured concrete, remaining in place if settlement of substrate occurs. Proofex Engage Thickness Engage 4-5mm Detail Strip 1.5mm 3.3mm LM LM Mesh

Width 1.27m 200mm

Length 30m 10m

Nominal 100m

50m

Edge Laps 68mm

End Lengths Butt ted

Weight 58kg 28kg

Ancillaries Proofex LM A two component applied trowelable membrane for sealing around intricate details such as pipe entries, penetrations, pile caps, etc. Proofex Engage Detail Strip A reinforced, double sided waterproof adhesive tape for sealing and ting roll ends, cut edges corner pieces. It consists of a strong synthetic fibre fabric impregnated and coated both sides with a bitumen rubber adhesive. Each side of the tape is protected by a removable siliconised paper. Proofex LM Mesh A reinforced mesh used in conjunction with Proofex LM for areas of extreme loading (covings, edges and pipe penetrations).

Proofex Hydromat Hydromat | Powder Proofex Hydromat Proofex Hydromat is a bentonite waterproofing membrane with unique surface bentonite impregnation for impermeable lap ts. Proofex Hydromat Roll Size 1.2m x 2.42m 2.42m x 15m

Roll Weight 18kg 210kg

Thickness 7mm dry 7mm dry

Ancillaries Hydromat Powder To ensure watertight continuity during detailing work and for sealing around awkward geometrical shapes, it may be necessary to cover an area with loose natural sodium bentonite powder. Hydromat Powder Size 30kg bag


5

Waterproofing Membranes Bituthene®

MRX | 2000 | 3000 | 4000 | 8000 | 4000DW

Bituthene® Membranes – Basement/substructure waterproofing and vapour proofing. Bituthene® is a range of flexible preformed post-applied basement waterproofing and vapour proofing membranes. Bituthene membranes are available in all grades to suit all climates, damp surface or green concrete application. Chemically resistant to provide effective external protection against aggressive soils, contaminated water, dilute acids and alkalis. Bituthene® MRX – Methane, CO2 and Radon resistant grade of Bituthene. Suitable for dry surface applications only. Bituthene® 2000 – For use below screeds. Suitable for dry surface applications only. Bituthene® 3000 – For basements and substructures. Methane, CO2 and radon gas protection. Suitable for dry surface applications only. Bituthene® 4000 – For basements and substructures. Methane, CO2 and radon gas protection. Suitable for application to damp surfaces and green concrete. Bituthene® 8000 – A Superior performance waterproofing membrane for basements and substructures. 70m hydrostatic pressure resistance with ultra low moisture transmission rate. Methane CO2 and radon gas protection. Suitable for application to damp surfaces and green concrete. Bituthene® 4000 DW – Designed specifically for waterproofing roofs of drinking water structures. Suitable for application to damp surfaces and green concrete. Bituthene® Type Bituthene MRX Bituthene 2000 Bituthene 3000 Bituthene 4000 Bituthene 8000 Bituthene 4000 DW

Roll size 1 x 20m (20m2) 1 x 25m (25m2) 1 x 20m (20m2) 1 x 20m (20m2) 1 x 20m (20m2) 1 x 20m (20m2)

Primer B1 B1 B1 B2 B2 B2

Application temp range +4 to +35°C +4 to +35°C +4 to +35°C -10 to + 35°C -10 to + 35°C -10 to + 35°C

Ancillaries Bituthene® Primers Specially formulated one part primers for sealing concrete and masonry surfaces to promote adhesion of Bituthene membranes. Bituthene Primers Type Primer B1- dry surface application only Primer B2 - dry/damp surface and green concrete application

Size 5 & 25 litres ( Approx 10m2/litre) 5 & 25 litres ( Approx 10m2/litre)

Bituthene® Protection Boards and tapes Robust, non degradable bitumen boards to provide protection to Bituthene membranes against backfill. Bituthene Protection Boards Type Bituthene Protection Board Bitustik™ 4000 (Adhere board to Bituthene) Bitutape™ 4000 (tape for over laps) Pack Adhesive


Size 3, 6, 12mm x 1m x 2m 150mm x 12m rolls 70mm x 20m rolls 5 litres

Waterproofing

6

Waterproofing Membranes Bituthene® LM Two component elastomeric cold applied liquid detailing compound. For use where liquid applied waterproofing is necessary to ensure watertight continuity, such as pile terminations, pipe penetrations, internal corners and membrane continuity through masonry walls. Bituthene LM cures to form a tough seamless rubber-like waterproof layer. Bituthene LM Type Bithuthene LM

Size 5.7 litres

Preprufe®

300R | 160R

Preprufe® Pre-applied waterproof membranes for basements and substructures that develop a continuous mechanical bond to poured concrete preventing water migration between the structure and the membrane, substantially reducing the risk of leaks. Preprufe 300R & 160R also provide protection against methane, CO2 and radon gas. For use below slabs and on reinforced concrete basement walls. Preprufe membranes are composite sheets comprising a robust HPDE backing, a pressure sensitive adhesive and a trafficable weather resistant coating. Preprufe 300R – under slabs greater than 350mm thick. Preprufe 160 R – under slabs less than 350mm thick and vertical applications. Preprufe Type 300R 160R

Thickness 1.2mm 0.8mm

Roll Size 1.2 x 30m 1.2 x 35m

Roll Area 36m2 42m2

Roll Weigh 50kg 42kg

Ancillaries Preprufe® Tape For sealing overlaps at Preprufe roll ends and cut ends. Preprufe Tape Type LT

Thickness 0.7mm

Roll Size 100mm x 15m

Roll Weight 2kg


7

Waterproofing Membranes Hydroduct®

200 | 220 | Coil 150

Hydroduct® Vertical Drainage Sheets Creep resistant drainage sheets are prefabricated geocomposites comprising studded polystyrene drainage cores covered with polypropylene filter fabric. They provide cost effective alternatives to traditional aggregate drainage. Hydroduct® 200 – Polypropylene spun bonded filter fabric on one face of a 11mm studded drainage core. Applied to walls of basements that have been waterproofed with Bituthene membranes and protected with Bituthene Protection Boards. Hydroduct® 220 – Polypropylene spun bonded filter fabric on one face of a 11mm studded drainage core with a bonded plastic film on the other. Applied to walls of basements that have been waterproofed with Bituthene membranes. Also applied to existing basement walls and permanent shuttering prior to the application of Preprufe membranes. Hydroduct® Coil 150 – Polypropylene non-woven filter fabric encapsulating a 25mm studded drainage core. Installed at the bottom of basement walls and linked to the Hydroduct drainage sheet. Hydroduct Type Hydroduct 200 Hydroduct 220 Hydroduct Coil 150

Thickness 11mm 11mm 25mm

Roll Size 1.25m x 32m long 1.25m x 32m long 150, 240mm x 30.5m long

Roll Area 40m2 40m2

Ancillaries Hydroduct Ancillaries Type Cut fastners (ting) Bitutstik™ 4000 (ting) Bitutape™ 4000 (ting)


Roll Size Strip 8 x 4 dimples, 5 supplied per roll 150mm x 12m long 70mm x 20m long

Roll Weight 40kg 40kg

8


Waterproofing

Sheetseal

226

Sheetseal Sheetseal is a cold applied, self adhesive bitumen sheet waterproofing membrane. It is typically used as an external basement tanking system or ground floor DPM, particularly where large unobstructed areas are to be waterproofed. Sheetseal Type 226 226 226

Thickness 1.6mm 1.6mm 1.6mm

Roll Size 1050mm x 19.05m 300mm x 20m 150mm x 20m

Weight 1.7kg/m2 1.7kg/m2 1.7kg/m2

Ancillaries Membrane Primers Sheetseal primer is a bitumen solution. Sheetseal Primers Type Sheetseal Primer Sheetseal Primer

Size 5 litres 25 litres

Coverage 7m2/litre 7m2/litre

Membrane Protection Boards Bitumen Protection Board is a tough, flexible bitumen impregnated board used for the protection of waterproof membranes against mechanical damage, pedestrian or vehicular traffic and abrasion caused by backfilling. Adhesive Tape Adhesive Tape is a double-sided tape, designed to be used in conjunction with the Bitumen Protection Board to adhere it to dry surfaces of bituminous type membranes. It may be used in ‘pads’ 150mm square, or in strips of suitable length. It can also be used to adhere to other materials, such as polyethylene sheets or similar, to most ‘dried’ RIW membranes. Bitumen Protection Board/Adhesive Tape Type Size Bitumen Protection Boards 0.9 x 1.28m Adhesive Tape 150mm x 15m

Thickness 3mm 2mm

Weight 3kg/m2 4kg/roll


9

Waterproofing Membranes Double Drain Double Drain Double Drain is an impermeable high density polyethylene profiled sheet incorporating a permeable geotextile filter fabric designed to prevent ground water reaching a structure and to protect and enhance the performance of the waterproof membranes. Double Drain Thickness 8mm

Roll Size 2 x 15m

Weight 0.62kg/m2

Plaster Drain Plaster Drain Plaster Drain is an internal drainage system manufactured from clear high density polyethylene with 5mm undercut studs in a dovetail shape which forms the key for plaster and render finishes in above and below ground situations. Plaster Drain Thickness 0.5mm

Roll Size 2m x 20m

Cavity Drain

Weight 0.48kg/m2

Overall Thickness 5mm

P5 l P20

Cavity Drain Cavity Drain is an internal tanking drainage system used to collect water entering the basements and sub-structures and channel it to a sump or collection point for disposal. P20 is used mainly on floors but can also be used for walls. P5 is used only for walls. Cavity Drain Type P5 P20

Roll Size 2.07m x 20m 2m x 20m

Weight 0.48kg/m2 0.95kg/m2

Ancillaries RIW Top Edging Strip A high-density profiled polyethylene sheet which protects the top edge of the RIW Double Drain and prevents clogging. RIW X Cramps A fixing aid for locating and mechanically securing the system to the substrate. RIW Overtape Butyl rubber tape, with a nonwoven polypropylene surface, for sealing over ts in the membrane. RIW Plaster Plugs A plastic plug for fixing membrane to structure.


Overall Thickness 5mm 20mm

RIW Sealing Tape A self-adhesive tape to seal ts between the RIW Wall / Floor Junction and membrane. RIW Sealing Rope A self-adhesive rope for sealing between individual sheets and around services, fixings etc. RIW Brick Plugs A fixing plug for vertical fixing of the Cavity Drain. RIW Wall / Floor Junction A pre-formed corner piece for assisting in sealing around corners and services. RIW Adhesive Tape A double-sided tape for adhering the RIW Wall / Floor Junction.

10


Waterproofing

Structureseal Structureseal Structureseal is waterproofing composite of high swelling Sodium Bentonite encapsulated between a non-woven and woven geotextile. When confined under pressure within a structure the swelling is controlled, forming a dense, monolithic, impervious waterproofing membrane.

Structureseal Type Structureseal

Thickness 6.4mm

Roll Size 1.1m x 5m

Roll Weight 35–40kg

Ancillaries Waterstop Waterstop is an active bentonite based waterstop that is designed to replace ive PVC/Rubber type waterbars thereby eliminating the requirement of special pieces and seam welding. Waterstop is not designed for, or intended to function as an expansion t sealant. Waterstop Type RIW Waterstop

Size 25 x 19mm

Supplied as 5m long coils

Sealing Compound Sealing Compound is a trowel-grade, sodium bentonite / butyl-rubber based sealant, designed for a variety of surface preparation and waterproofing detail work, for use with the RIW Structureseal system. Being a bentonite based material, Sealing Compound swells upon with water to seal against water intrusion. With the consistency of thick grease, Sealing Compound is easy to apply and bonds to most materials. Sealing Compound Type Sealing Compound

Size 14.25 litres

Weight 18kg

Granules Granules are chemically treated sodium bentonite granules, which are used as a detailing accessory product, with the RIW Structureseal system. When hydrated and in containment, the Granules form into a dense, impermeable material, that combines with the sodium bentonite in Structureseal to form a seamless waterproof membrane. Granules Type Granules

Size 20kg tub

Washers 40mm hardened nail with 30mm premounted washer for securing the RIW Structurseal to concrete by hand nailing or shot firing. Staple Gun A manual stapler for fixing sheets of Structurseal together at laps etc.


11

Waterproofing Membranes B U I L D I N G

P R O D U C T S

Plasprufe

MP | 2000SA | 3100 | 3100HD

Plasprufe Plasprufe is a range of SBS polymer modified bitumen waterproofing systems for use in cast concrete, brick and blockwork constructions, both internally and externally, to protect buildings against water from the ground. All Plasprufe membranes have BBA certification. Plasprufe MP is a multi-purpose, self adhesive damp proof and tanking membrane. Plasprufe 2000SA is a tougher, more durable self adhesive damp proof and tanking membrane. Plasprufe 3100 is a high performance torch applied tanking membrane, ideally suited for tanking in cold and damp conditions. Excellent lap adhesion and security is achieved by torch application. Plasprufe 3100HD is a high performance torch applied tanking membrane, ideally suited for tanking in cold and damp conditions. It has a tough, non-woven polyester fibre facing, which eliminates the need for a separate protection board when externally tanking. Excellent lap adhesion and security is achieved by torch application. Plasprufe Type Plasprufe MP Plasprufe 2000 SA Plasprufe 3100 Plasprufe 3100 HD

Size 20m x 1m 15m x 1m 10m x 1m 10m x 1m

Thickness 1.5mm 2.0mm 3.0mm 3.7mm

Ancillaries IKOpro SA Bitumen Primer A rubber-modified bituminous priming solution designed to seal and prepare surfaces for the application of self-adhesive damp proofing or tanking membranes. It is fast-drying and is ideal for ensuring a long-term bond between the surface and subsequent membranes being applied. It may be applied to many substrates including concrete, wood, brickwork, blockwork and metal. IKOpro Fast Dry Primer A quick-drying and deep-penetrating priming solution designed to seal and prepare surfaces for the application of torch applied tanking membranes. IKOpro Fast Dry Primer dries in approximately 30 minutes at 20°C, depending on the substrate, and leaves no residual tack. Suitable for use on dry or slightly damp surfaces. It may be applied to many substrates including concrete, wood, brickwork, blockwork and metal. Plasprufe Protection Primers Type IKOpro SA Bitumen Primer IKOpro Fast Dry Primer

Size 5, 25 litre cans 5, 25 litre cans

Coverage Concrete 3-4 m2/litre, Metal 10-15 m2/litre Concrete 3-4 m2/litre, Metal 10-15 m2/litre

Plasprufe Protection Board A tough, flexible polymeric board for protecting tanking membranes against mechanical damage, pedestrian or vehicular traffic and abrasion caused by backfilling. Plasprufe Protection Board also protects against ground salts and most corrosive chemicals. Membrane Protection Boards Type Plasprufe Protection Board Plasprufe Protection Board WWW.SU PPORTSITE.CO.U K

Thickness 1.5mm 3.0mm

Size 2m x 1m 2m x 1m

Waterproofing

12

Waterproofing Membranes PlasDrain.12 and PlasFlow.25 Structural Drainage Systems Plasdrain is a high performance geocomposite drainage layer that offers distinct benefits over aggregate filter beds. Plasdrain.12 structural drainage systems have been specifically developed to provide high flow capacity while offering protection to Plasprufe tanking membranes. PlasDrain.12 should be used in conjunction with PlasFlow.25 flow drain. Structural Drainage Systems Type PlasDrain.12 PlasFlow.25

Bitusheet

Size 50m x 1.1m 50m x 100mm

XL Membrane

Bitusheet XL Bitusheet waterproofing membranes consists of a self bonding polymer modified bitumen which is covered on one side by a tough two ply cross laminated polythene film and protected on the other side by a release sheet which is removed prior to the bonding of the material on to a suitably prepared substrate. Once the release sheet has been removed the membrane can be easily applied by roller pressure. Bitusheet Type XL

Size 1.05 x 19.05m

Ancillaries HD Protection Boards Bitusheet HD Protection Board is a tough, flexible polymeric board specifically developed for protecting the Bitusheet range of self adhesive waterproofing membranes, against mechanical damage, foot and normal site traffic and abrasive backfill materials. Due to its high strength and excellent puncture resistance the Bitusheet HD Protection Board exceeds the performance of thicker protection boards. It can be easily cut and shaped on site. Bitusheet Primer A one part bituminous solution for brush or spray application. Tapes Reinforcing (XL) Tape Bitusheet Self Adhesive Reinforcing Tape comprises of a cross-laminated high-density polyethylene sheet coated with a Bitumen Polymer Adhesive faced with a release sheet. Double Sided Tape Self Adhesive Double Sided Tape comprises of a Polymer Modified Bitumen 1.5mm thick faced on both sides with a release sheet. Bitusheet HD Protection Boards Type Thickness HD Protection Board 1.5mm HD Protection Board 3.0mm Bitusheet Primer Type Bitusheet Primer

Size 5, 25 litres

Coverage 12m2/litre

Sheet Size 2m x 1m 2m x 1m Tapes Type Reinforcing Tape Double Sided Tape

Weight 2.5kg/m2 5.0kg/m2

Roll Width 100, 150, 300mm 100, 150, 200mm

Roll Length 20m 15m


13

Waterproofing Membranes Dual Seal Dual Seal is a high performance self swelling, self healing waterproofing membrane comprising of a thick, tough, high density polyethylene sheet laminated to 4kg/m2 of quality Bentonite granules. The Bentonite used in the manufacture of Dual Seal is capable of repeated cycles of wetting and drying without deterioration of its sealing properties and has a life expectancy measured in thousands of years. It has WRAS approval for use with potable water and is BBA Certified. Dual Seal Type HDPE Thickness HDPE 0.5mm

Membrane Thickness 5.0mm

Roll Width 1.22m

Roll Length 7.32m

Coverage Per Roll 8.51m2

Ancillaries Dual Seal Mastic A trowlable mastic comprising of a special formulation of expandable minerals and elastomeric compound which expands and stiffens in the presence of water to form an impervious barrier to water penetration. Size: 19 litres. Dual Seal Granules A high swelling sodium bentonite in granular form which reacts when in with water and forms an impervious gel. Size: 22.7kg (23.6 litres) bags. Bitusheet XL Tape Used as an overband tape for the sealing of membranes to membranes. Size: 100,150, 300mm roll widths, all rolls are 20m in length.

Walldrain

Slabdrain

Walldrain Walldrain consists of a cuspated lightweight plastic core bonded to a geotextile fibre filter. The fibre will permit free entry of water, but not soil, and so prevent soil particles from clogging drainage systems. Walldrain is designed to be placed with the geotextile filter layer facing the direction of the water seepage or backfill. Slabdrain Slabdrain is a cavity drain former manufactured from a dimpled H.D.P.E, designed to provide a drainage channel beneath the concrete in floor and wall construction. The former is provided with selvedges to enable ts to be sealed to give a water and gas tight membrane. Slabdrain Roll Size 1m x 50m

Thickness 10, 20mm

Ancillaries Soft Washer Fixing Fast, reliable fixing for membranes, mesh or insulation. Soft Washer Fixing Size Box Quantity 150 Nail 37mm Washer 36mm

Anchor Plug Drill 8mm hole and set with hammer. Use mastic tape to form a washer seal under head. Anchor Plug Size 8 x 75

Box Quantity 100

Membrane Washers For use with washered nails.

Washered Nails Washered Nails Size 25, 30, 40mm

Walldrain Roll Size 12mm x 1m x 50m 25mm x 0.9m x 50m

Box Quantity 500


Membraned Washers Size 19, 32mm

Box Quantity 100

14

Waterproofing Membranes Liquid Membranes Liquid Membranes Products in this section range from simple bituminous paints for the protection of steel and concrete from water, through to bitumen latex compounds to two part epoxides giving protection from abrasion and chemicals as well. There are also others that can be used as part of sheet membrane systems for detail work.

Products

Page

Mulseal DP Proofex LM

15 15

Bituthene LM Procor

15 16

Aquamac

16

Flexiseal/Heviseal Hydrocoat LAC Toughseal

17 17 18 18

B U I L D I N G

Waterproofing

Waterproofing

14

P R O D U C T S

Synthaprufe

19

Multiprufe

19


15

Liquid Membranes Mulseal DP Mulseal DP Mulseal DP is a bitumen rubber/latex compound designed for use in waterproofing applications. Mulseal is suitable for uses such as waterproof membrane to retaining walls, as a vapour barrier to s and repairing fine cracks in asphalt surfaces. MulsealDP Type Mulseal DP

Size 5, 25, 200 litres

Coverage 1.1 - 1.4m2/litre*

*Depending on surface texture.

Ancillaries Fosroc Primer 3 Metal and timber surfaces must be primed with a coat of Primer 3 before applying Mulseal DP.

Fosroc Primer 3 Type Fosroc Primer 3

Size 5, 25 litres

Proofex LM Proofex LM Two component bituminous liquid membrane for waterproofing of underground structures and intricate details in conjunction with Proofex waterproofing systems. A rubber emulsion with special hydraulically hardening fillers. It can be applied to damp surfaces and resists hydrostatic head of up to 70 metres. Proofex LM is solvent-free, resistant to aggressive ground water and is applied by trowel. Proofex LM Type Proofex LM

Size 28kg pack

Bituthene® LM Bituthene® Liquid Membrane Two component elastomeric cold applied liquid detailing compound. For use where liquid applied waterproofing is necessary to ensure watertight continuity, such as pile terminations, pipe penetrations, internal corners and membrane continuity through masonry walls. Bituthene LM cures to form a tough seamless rubber-like waterproof layer. Bituthene Liquid Membrane Type Size Bithuthene LM 5.7 litre pack

Bituthene Liquid Membrane Approximate Coverage Rates 2.5mm thick x 300mm wide 2.5mm thick x 2 x 150mm wide with 20mm fillet 20mm fillet


Bithuthene LM 5.7 Litre Pack 7.6 lin metres 6.0 lin metres 28.4 lin metres

16

Liquid Membranes

Waterproofing

Procor®

10 | 20

Procor® Procor® is a two component, synthetic rubber, liquid waterproofing membrane. It cures to form a resilient, fully bonded elastomeric sheet. Procor® will protect structures against water and water vapour ingress. At a single coat thickness of 1.5mm, Procor® will resist a hydrostatic head in excess of 20m when fully loaded. Damp surface tolerant, can be applied to green concrete and damp to touch surfaces. Procor® 10: Trowelling grade for horizontal surfaces. Also recommended for vertical application at temperatures less than 12°C. Procor® 20: Trowelling grade for vertical surfaces at application temperatures above 12°C. Procor® Type Procor® 20 Procor® 10 (Summer Pack) Procor® 10 (Winter Pack)

Size 7.5 litres 20 litres 7.5 litres

Coverage 4.5m2/unit 12m2/unit 4.5m2/unit

Ancillaries Procor® Type Grace® Protection Board Servipak® 3 Protection Board Armourtape™ Hydroduct® 200 Preprufe® Tape Servit® One DW Adcor® 500S Bitutape™ 4000

Size 1.0m x 2.0m 1.0m x 2.0m 75mm x 10m roll 1.25m x 32m 100mm x 15m roll 310ml 6 x 5m rolls 70mm x 20m roll

Procor® Concrete Sealer Procor® Concrete Sealer Procor® Concrete Sealer is a water-based surface conditioner designed to mitigate problems associated with the application of Procor® to cast concrete and masonry substrates in conditions where an air or vapour drive is likely to cause blistering or pin-holing of the Procor® surface. Procor® Conrete Sealer Type Procor Concrete Sealer

Size 18.9 litre buckets

Aquamac Bituminous Black Paint Aquamac Bituminous Black Paint A solvent-borne bituminous black paint. For the protection of ferrous and non-ferrous metals, concrete roofing felt, fibre cement, corrugated iron, asphalt and wood against water. Aquamac Sizes 5, 25 litre

Coverage approx 6.5m2/litre


17

Liquid Membranes Flexiseal Flexiseal Flexiseal is a two colour, seamless and fully bonded liquid applied waterproof coating based on polyurethane technology. RIW Flexiseal cures by drawing moisture from the air to form a highly flexible but durable barrier to water and water vapour and is typically used where a high performance tanking system is required. Available in black or grey. Flexiseal Type RIW Flexiseal RIW Flexiseal Primer

Size 6, 25kg 5, 20 litres

Coverag 2m2/kg/coat 8m2/litre

Ancillaries Protection Board/Sheetseal Type RIW Protection Board RIW Sheetseal 9000 DPC

Size 3mm x 1.285m x 1.625m Available in standard sizes

Heviseal Heviseal Heviseal is typically used to provide a protective coating to concrete or steel superstructures or other structures such as retaining walls, plinths etc. RIW Heviseal is suitable as a waterproof membrane, for periodic maintenance onto existing flat roof area. The membrane can also be used on parapet walls, gutters, planters, ponds and water storage tanks. Heviseal has excellent U.V. resistance. Heviseal Type Heviseal

Size 5, 20 litres

Coverage 1.5m2 per litre/coat

Hydrocoat Hydrocoat Hydrocoat is an easily applied, high build black bitumen paint, which dries to a water and water vapour proof finish. It may be easily applied to most building substrates. Hydrocoat Type RIW Hydrocoat

Size 5 litre Tins 25 litre Drums 205 litre Barrels


Coverage 3m2/litre in 2 coats 3m2/litre in 2 coats 3m2/litre in 2 coats

18

Liquid Membranes

Waterproofing

LAC LAC Liquid Asphaltic Composition is typically used as a damp proof membrane to ground floors, as a vapour barrier behind cladding and for tanking of basements. It is also suitable for waterproofing foundation walls, ducts, lintels, columns, beams and similar structures at, above and below ground level and as a radon barrier. LAC Type RIW Liquid Asphaltic Composition

Sizes 5 litres 25 litres 205 litres

Coverage for two coats 1m2/litre (typical 2 coats ) 1.25m2/litre (steelwork 2 coats)

Ancillaries Sheetseal 226 Sheetseal Sizes 150, 300mm x 20m Also see page 8

Toughseal Toughseal Toughseal is typically used to provide a water and water vapour proof barrier, or to give protection against abrasion, fresh and salt water, carbon dioxide, alkalis and dilute mineral acids. It is resistant to U.V. light and atmospheric attack. Suitable uses for Toughseal include, raised access floors, ground floor slabs, swimming pool wet areas and shower areas, plant rooms, sewage plants and marine applications. When dressed with a suitable aggregate it will provide a slip retardant wearing surface or a waterproof key for tile bedding or renders. Available in black or grey. Toughseal Type Toughseal

Size 5, 20 litres

Coverage 4m2/litre/coat

Ancillaries Aggregate/Solvent Type Aggregate, Grade 1 Aggregate, Grade 2 Cleaning Solvent Flexiseal

Size 25kg 25kg 5 litres 6, 25kg


19

Liquid Membranes B U I L D I N G

P R O D U C T S

Synthaprufe

Original | LAC

Synthaprufe Original IKOpro Synthaprufe Original is a high performance, brush applied damp proofing emulsion containing synthetic rubber latex which provides a waterproof and vapour resistant, black elastomeric membrane. Synthaprufe Original exhibits low odour, with exceptional flexibility and crack resistance, even at low temperatures and offers excellent resistance to sulphates and other soil salts. When suitably protected, Synthaprufe will be effective through the life of the building. Synthaprufe bonds with great strength to a range of building materials. For use as damp proofing of concrete, brick, blockwork and masonry, with vertical surfaces being finished with a gypsum based plaster system. Adhesive for unsealed wood block flooring (min 10mm thick). Suitable for tanking of basements. Synthaprufe LAC High performance liquid damp proof membrane IKOpro Synthaprufe LAC is a high performance waterproofing liquid used as a damp proof membrane and waterrepellent coating, prior to the erection of masonry. It forms a flexible membrane when cured and provides an effective barrier to water and water vapour. Synthaprufe LAC is easy to apply and is suitable for use in the most demanding site locations. For use in waterproofing of foundations, retaining walls, abutments, steel columns, beams, lintels and structures where cladding is to form the outer leaf.

Synthaprufe Type Synthaprufe Original

Size 5, 25 litre cans

Synthaprufe LAC

5, 25 litre cans

Coverage Floors: 1st coat 1m2/litre; 2nd coat 1.5m2/litre Walls: 3 coats each 2m2/litre Metal surfaces: 1st coat 2.5m2/litre; 2nd coat 2.5m2/litre All other surfaces: 1st coat 1.5m2/litre; 2nd coat 2.5m2/litre

Multiprufe Multiprufe A thixotropic cold applied rubberised bitumen emulsion which dries to provide a tough, black flexible coating for brickwork, concrete and steel. Can be used for waterproofing columns etc., and general purpose ‘black jack’. Complies with specification for Roads and Bridges DOE clause 2006 (s) Waterproofing for structures. Multiprufe Type Multiprufe


Coverage: 4–6m2/Litre per coat depending on surface


Waterproofing

20

20

Waterproofing Membranes Waterstops and Waterplugs Waterstops and Waterplugs

Products

Prevention of water ingress and outgress into a structure is of vital importance. This section shows products that stop the flow in two different ways.

Page

Thoro Waterplug

21

Fastfill WP

21

Renderoc Plug Supercast

21 21

Adcor 500S AT System PVC Edgetie Serviseal Servistrip AH205 Servitite

24 25 25 26 26 26

Waterstop

27

Dual Stop Dualtite PVC Waterstop Profiles Swelltite Superstop Uraswell

27 27 28 28 29 29

Sika 2, 3, 4, 4A Sika Swell Sika Injectoflex

29 30 30

Hydrotite

30

Plug

30

PVC Profiles

31

Waterstops. The prevention of ingress during construction, they are cast into construction ts and take four different forms; • PVC strips cast centrally or on the face to provide a physical barrier to the age of water (see Fosroc Supercast) • Hydrophilic strips placed in ts which expand when in with water to seal the t (see Grace AH205). There are also combinations of PVC and hydrophilic (see S Dualtite) • Injection hoses cast in through which resins can be pumped if leaks occur (see Sika Injectoflex) • Hydrophilic sealants which also swell in with water (see S Uraswell) Waterplugs Are used to seal leaks that occur after construction, these come as in two formats; • Liquids that are added to cement in different concentrations to give different speed of set • Powder products that just need the addition of water


21

Waterstops and Waterplugs Thoro Waterplug Thoro Waterplug Thoro Waterplug is a blend of hydraulic cements, well graded sands and chemical additives supplied in a dry powder form. It requires only the addition of clean water to produce a ready to use, ultra rapid setting plugging mortar. Thoro Waterplug Type Thoro Waterplug

Sizes 5, 25kg

Coverage: 1kg powder will fill 585cm3

Fastfill WP Fastfill WP Fastfill WP is a safe and simple to use ultra-rapid setting mortar for arresting water seepage and infiltration under pressure through cracks, ts and voids in concrete and masonry prior to the application of cementitious coatings and mortars. It is a single component, polymer modified, fibre reinforced mortar based on shrinkage compensated Portland Cement, which is non caustic in use. Fastfill WP Type Fastfill WP

Sizes 8kg

Yield 4.25 litres per 8kg

Coverage: 1kg powder will fill 530cm3

Renderoc Plug Renderoc Plug Renderoc Plug is a rapid setting mortar which is easy to apply to horizontal, vertical or overhead surfaces at a wide range of thicknesses. There are two grades available: Renderoc Plug 1 with an initial set time of approximately 1 minute, and Renderoc Plug 20 with an initial set time of approximately 20 minutes. (Set times are based on ambient/substrate temperatures of 20°C.) Renderoc Plug Type Renderoc Plug 1 Renderoc Plug 20

Size 6kg bags 25kg bags

Coverage 3 litres 12.5 litres

Supercast Twinstop Supercast Twinstop Supercast Twinstop has been specially designed to provide significant advantages over co-extruded hydrophilic waterstops. This enables the PVC waterstop to be fixed on site in the usual way and provides the additional benefit of two hydrophilic elements treated with a retarded swell coating, thus avoiding the common problem of hydrophilic pre-swell on site. Supercast Twinstop Type Supercast Rearguard TS Supercast Hydrofoil TS

Sizes 250mm 250mm

A range of prefabricated junctions and intersections is available, also see generic profiles and accessories on page 31.


22

Waterstops and Waterplugs

Waterproofing

Supercast Butyl-Nek Supercast Butyl-Nek Supercast Butyl-Nek is a rubber/bitumen pre-formed flexible sealing strip specifically used to provide a permanent watertight t for pre-cast units which are ted together on site. Applications include ts in manholes, inspection chambers, box culverts and concrete pipes. This easily compressible product is designed to completely seal and fill the annular space between pre-cast units regardless of shape or size. Supercast Butyl-Nek associated products have a 50-year proven track record in the most extreme situations and are specified and used by pre-casters and contractors worldwide. Supercast Butyl-Nek Type Supercast Butyl-Nek

Sizes 12mm x 60mm 12mm x 80mm 12mm x 120mm 18mm x 18mm 22mm x 22mm 25mm x 40mm

Ancillaries Supercast Butyl-Nek - Primer Type Supercast Butyl-Nek Primer

Sizes 5, 25 litres

Supercast Hydrofoil Supercast Hydrofoil The Supercast range of PVC waterstops is designed to provide an integral sealing system for movement and construction ts in concrete cast in-situ. Centre bulb sections are used in expansion, contraction and construction ts. The centre bulb allows for movements in a structure to be accommodated whilst its hexagonal design provides a flat surface. This allows shuttering and t fillers to fit snugly. All centrally placed Supercast waterstops incorporate an eyeletted, reinforced edge flange. This enables them to be easily positioned by wiring to surrounding reinforcement. Supercast Hydrofoil Type Supercast Hydrofoil

Rearguard S XHD Hydrofoil

Section width 250mm 200mm 250mm 200mm 250mm

Sizes Roll weight 27.1kg 27.3kg 33.4kg 24.0kg 42.9kg

Roll length 12m 15m 12m 12m 10m



23

Waterstops and Waterplugs Supercast Joco 10 Supercast Joco 10 Multiple injection hose for protection against potential and active leaks in concrete structures. Supercast Joco 10 is a resin injection system developed to provide increased water integrity for construction ts in water retaining and excluding structures i.e. tanks and basements. Supercast Joco 10 Type Supercast Joco 10

Sizes 14mm x 20m coil

Supercast SW SW10 | SW20 Supercast SW10 and SW20 The Supercast SW range consists of swellable waterstops; Supercast SW formed sections, Supercast SWX gun-applied paste and Supercast SW adhesive. Supercast SW sections are made from high performance synthetic elastomeric strips. The swelling action of the Supercast SW range is the result of between water and hydrophilic groups which are an intimate part of the Supercast SW polymeric structure. These hydrophilic groups are not subject to extraction and loss of swelling performance by prolonged or repeated wetting. Expansion of the waterstop creates a positive pressure against the faces of the concrete t, thus preventing water ing through the t. Supercast SW10 and SW20 Type Supercast SW10 Supercast SW20

Sizes 5mm x 20mm x 15m rolls 10mm x 20mm x 5m rolls

Coverage Usually single run of strip per t Usually single run of strip per t

Ancillaries Supercast SW Type Supercast SWX Supercast SW Adhesive

Size 310ml cartridge 380ml cartridge


Coverage 1.5m @ 16mm bead per cartridge Approx 13m @ 5mm bead per cartridge

24


Waterproofing

Supercast Synkoflex Supercast Synkoflex Supercast Synkoflex is a unique non-swelling, pre-formed plastic adhesive waterstop that bonds fast to cured concrete surfaces and fuses with fresh concrete. Supercast Synkoflex offers a host of practical advantages in application. It provides watertight integrity for construction ts in concrete structures in places where swellable waterstops are not best suited, such as bund walls and thin section walls and slabs. It has exceptional adhesion and malleability, making it an excellent choice for steel sheet piling/floor slab ts. Supercast Synkoflex comes with an extensive track record of more than 30 years proven reliability on major projects in the USA - now extending to Scandinavia, the UK and other major European countries. Supercast Synkoflex Type Supercast Synkoflex Supercast Synkoflex FR

Sizes 25mm x 25mm 12mm x 30mm

Quantity Box of 25mm x 1m strips Box of 6mm x 5m rolls

Ancillaries Supercast Synkoflex Type Supercast Synkoflex Primer

Size 3.79 litres 18.9 litres 2 litres

Supastik E10 Adhesive

Adcor® 500S Adcor® 500S A conformable, swellable polymer/butyl rubber waterstop strip for construction ts that expands in with water. When fully encapsulated by poured concrete, the expansive forces form a seal against concrete faces. The seal resists hydrostatic pressure, stopping water from entering sub-structures. Adcor® is a unique product that has been specifically developed to provide better performance than conventional swellable rubber waterstops. Adcor 500S Type Adcor 500S

Adcor Mastic Adcor Adhesive MS

Size 5m rolls 6 rolls/carton 30 cartons/pallet 310ml cartridge 310ml cartridge

Ancillaries Adcor 500S Type Adcor 500S Mesh Profile Large Secura Clips

Size 1m strips, 30 strips/bundle Each


25

Waterstops and Waterplugs AT System AT System AT System waterstops have been specially developed for water excluding and retaining structures such as basements, reservoirs, sewage treatment works, etc. The AT System is an important advance in concrete t protection which combines Active Technology with the conventional mechanical properties of PVC waterstops. Conventional PVC waterstops work by the normal action of the concrete shrinking away from the t and against one face of the ribs or bulbs of the waterstop. This creates positive pressure on the rib or bulb causing a “valve action” to resist water ingress. However, this shrinkage movement also forms an inevitable void on the opposite face of the rib or bulb which can allow water under high pressure to track along the waterstop searching for a path to by the waterstop. Subsequent cyclical movement of the t can compound the problem resulting in further leakage. AT System waterstops mechanical properties prevent water ingress by the same valve action but also actively seal the void around the rib or bulb to stop water bying or migrating. The hollow core of the bulb deforms to control the expansive forces to prevent damage to the concrete. Servitite® AT 200 (10mm web thickness) – an internally placed waterstop, which is cast centrally in the comcrete to resist internal and external water pressure. Serviseal® AT 240 – can be cast on the external face for water excluding structures such as basements or sub structures or ground bearing slabs only of water retaining structures. AT System Type Servitite® AT 200 Serviseal® AT 240

Sizes 7.5m long coil, weight 20.2kg 7.5m long coil, weight 25.1kg


Ancillaries Small 20mm Secua Clips – To tie Servitite AT 200 to reinforcement ting Jig – jig AT system Welding Knife – Large electric knife (110V or 220V)

PVC EdgetieTM PVC EdgetieTM PVC Edgetie™ (5mm web thickness) is an internally cast ive waterstop system manufactured in a range of sizes for sealing construction and expansion ts in concrete structures subject to water pressure. PVC Edgetie Type PVC Edgetie 210 PVC Edgetie 260

Size 10m coil 7.5kg

Weight 18.3kg 19.6kg


Ancillaries ting Jig – jig AT system Welding Knife – Large electric knife (110V or 220V)


26


Waterproofing

Serviseal® Serviseal® Serviseal® is a ive external PVC waterstop system manufactured in a range of sizes for protecting ts in concrete basements and sub-structures. Serviseal external flexible waterstop systems have a proven design using four T shaped ribs for solid embedment in insitu concrete which create a valve action to seal the water path, and are suitable for horizontal and vertical applications. Being cast into the outside water face prevents the ingress of moisture and protects the outer layer of reinforcement from corrosion. Location on the outside face of a concrete member also promotes better compaction of the concrete around the ribs of the Serviseal since it is free from reinforcement congestion and the weight of wet concrete makes consolidation easier. Seviseal can be used for non suspended slabs in water retaining structures such as reservoirs, swimming pools and sewage treatment works. Serviseal Type Serviseal 195 Serviseal 240 Serviseal K320 Serviseal Pilecap

Size 10m coil 7.5m coil 7.5m coil 7.5m coil

Weight 19.7kg 21.5kg 23.8kg 24.0kg


Servistrip® AH205 Servistrip® AH205 Servistrip® AH205 is a hydrophilic solid rubber strip that exceeds the performance of thinly coated or hollow swellable strips. Servistrip AH 205 can be cast into insitu concrete or used between new and existing concrete sections to provide a highly effective watertight seal. The rate of swelling is controlled to allow installation and exposure to rain. The swelling pressure does not cause spalling or damage to freshly poured concrete before it has time to reach its design strength. The simple, solid form also allows it to be used in difficult locations such as diaphragm and secant piled walls. Also concrete surfaces where other sealing methods would be impractical. Servistrip AH205 Type Servistrip AH205

Section 20mm x 5mm

Length 10m

Servitite® Servitite® Servitite® (10mm web thickness) is an internally cast specially formulated PVC waterstop system manufactured in a range of sizes for use in reinforced concrete structures. Being cast into the centre of the concrete member, Servitite® waterstops will provide resistance against high hydrostatic pressure from both faces. It is essential to form a continuous waterstop network at all ts to prevent the ingress or escape of moisture/water. For changes of direction or profile only factory produced fabrications should be used with site ting limited to simple butt welds. Servitie Type Servitite 150 Servitite 230 Servitite 305

Size 7.5m rolls 5.0m rolls 5.0m rolls

Weight 20.5kg 24.7kg 27.2kg

See Tools and Accessories Section for Accessories.


27

Waterstops and Waterplugs Waterstop Waterstop Waterstop is a sodium bentonite based material, designed to stop water infiltration through insitu concrete construction ts. Sodium bentonite swells when in with water, forming an impermeable barrier. This swelling property allows the Waterstop to form a permanent pressure seal within the concrete t, thus eliminating water migration over or along the waterstop. The key to the products effectiveness is its 75% sodium bentonite content, which provides superior expansion, to seal and fill voids and cracks within the concrete. Waterstop is an active bentonite based waterstop, that is designed to replace ive PVC / Rubber type waterbars, thereby eliminating the requirement of special pieces and seam welding. Waterstop is manufactured in light - weight, flexible coils that are easily installed in hot or cold weather conditions, by a single worker. Waterstop Type RIW Waterstop RIW Mesh

Sizes 25m x 19mm, supplied in 5m long coils. A box of 50 600mm lengths including fixing nails 30 linear metres per box

Dual Stop Bentonite Waterstop Dual Stop Bentonite Waterstop Dual Stop Waterstop is a Bentonite based waterstop which reacts in with water by swelling to form a watertight seal in concrete structures. It has been independently tested up to 30 metre head of water. It has full WRAS approval for use with potable water. Dual Stop Waterstop has been specifically designed to seal construction ts against the ingress or outgress of liquids in water retaining or excluding structures. It is fixed by nailing to the face of the existing pour prior to placing the next pour. It is installed directly onto scabbled surfaces and will swell into voids up to 12mm deep. Changes of direction and end ts are simply achieved by butting together, no welding or adhesives are required. Dual Stop Bentonite Waterstop Type Size Dual Stop Waterstop 7mm x 25mm

Roll size 8m

Dualtite Hydrophilic Expansion t Waterstop Dualtite Hydrophilic Expansion t Waterstop Dualtite Waterstop consists of a PVC profile manufactured from weldable waterstop grade material incorporating Dual Seal Hydrophilic Bentonite Waterstops, which swell in with water, to form a totally watertight seal. The lug on either side of the central section, ensures that Dualtite is fully embedded into the adjacent concrete surface, and its unique central core design allows the t to open up to 50%. When Dual Seal Bentonite Waterstop is installed in Kicker or Construction ts, it is simply butt ed to the integral Dual Seal Waterstop, in the Dualtite, to create a totally watertight system. Dualtite Hydrophilic Expansion t Waterstop Type Dualtite Hydrophilic Expansion t Waterstop


Roll Length 8m

28


Waterproofing

PVC Waterstops Profiles PVC Waterstops Profiles S PVC Waterstops are available in various profiles for different concrete t situations. Flat Dumbell and Centrebulb types are used for internal waterstop details and have been independently tested to prevent the ingress of water, up to 27m head in construction and expansion ts in water retaining and excluding structures. Extaseal external PVC Waterstop is a high performance heavy duty profile specifically developed to seal ts in concrete structures at the outside surface. Pilecap waterstop has been specifically developed to provide a watertight seal between the pilecap and floor slab in concrete structures. Extaseal Type Construction t Expansion t Kicker t Roll Size

Width 200mm 200mm 15m

250mm 250mm 250mm 10m

320mm 320mm 10m

Pilecap Type - Pilecap Width Construction t 125mm x 125mm Expansion t 125mm x 125mm

Roll Size 25m 25m

A range of prefabricated junctions & intersections are available, also see generic profiles & accessories on page 31.

Dumbell and Centrebulb Type Width x 5mm web (Eyeletted) Flat Dumbell Construction t 150, 200, 260mm Centrebulb Expansion t 150, 200, 260mm Roll Size 15m

Width x 10mm web (Heavy Duty) 150, 250mm 150, 250, 305mm 10m

Swelltite Hydrophilic Self Swelling Waterstop Swelltite Hydrophilic Self Swelling Waterstop S Swelltite Hydrophilic Waterstop is manufactured from a neoprene polymer based hydrophilic compound and high water absorbent resins. Swelltite has been specifically designed for use in sealing construction ts between pre-cast concrete units, steel and insitu concrete. Unlike traditional waterstops Swelltite is centrally placed and bonded flat in the t prior to making the second pour, activated by water Swelltite will swell up to 5 times it’s volume and seal the age of water by exerting pressure across the t. Swelltite rolls are self adhesive. Porour Surfaces should be sealed with Primer P. Swelltite Hydrophilic Self Swelling Waterstop Type Size Swelltite Hydrophilic 20mm x 5mm Primer P 1 litre cans

Roll Size 15m

Bentorub + | Salt Bentorub + Bentorub is a green flexible hydrophilic strip made of natural bentonite clay and synthetic rubber. It is designed for the sealing of concrete ts, cold ts and working ts in concrete, around pipe penetrations, in sewer ts, against slurry walls and sheet piling. Bentorub Salt A Red flexible hydrophilic strip made of natural bentonite clay and synthetic rubber. It is has the same applications as Bentorub+ except Bentorub Salt may only be used in with salt and Brackish water.

Hydophilic Waterstop Size Type Bentorub+ 20mm x 25mm Bentorub Salt 20mm x 25mm

Roll Size 5m 5m


29

Waterstops and Waterplugs Superstop Self Swelling Waterstop Superstop Self Swelling Waterstop S Superstop has been developed to provide a watertight seal in construction ts, and is particularly effective when used in ‘box out’ applications. When water comes into with Superstop the bentonite expands to form a pressure seal which has been successfully tested to withstand a 33 metre head of water without leakage. Superstop Self Swelling Waterstop Type Sizes 25mm x 12mm Superstop 25mm x 19mm

Roll Length 6m 3.9m

Uraswell Hydrophilic Sealant Waterstop Uraswell Hydrophilic Sealant Waterstop S Uraswell is a polyurethane based sealant which swells in with water and forms a permanent waterproof seal. Uraswell is solvent free and non-toxic and is easily applied with a barrel gun, it provides excellent adhesion on many materials including uPVC. Uraswell Hydrophilic Sealant Waterstop Type Size Uraswell Hydrophilic Sealant 600ml sausages Barrel Gun 600ml

Sika

2 | 3 | 4 | 4A

Sika 2, 3, 4 & 4A Sika 2, 3, 4 & 4A are all purpose waterproofing liquids with various setting times and/or waterproofing properties. Setting time dependent on concentration. SIKA 2 Sika-Plug, is Sika’s fastest setting point leak plugging product when used neat, for point leak plugging where high water ingress is present. SIKA 3 All purpose setting and hardening accelerator also repairing cracks and ts (contains calcium chloride). A mortar accelerator for sealing ts in brickwork, blockwork, masonry and rock fissures. SIKA 4 Accelerator, waterproofer, also for oil resistant renders and underwater concreting. For point and surface waterproofing against seepage, particularly sea water and sewage. SIKA 4a Quick setting waterproofer for renders and leak sealing, setting in about 45 seconds. For point and surface waterproofing against general seepage (should be covered with Sika 1 render). Sika Waterproofing Liquids Type Set time Sika 2 10 to 20 seconds Sika 3 20+ seconds Sika 4 25+ seconds Sika 4A 45 seconds

Consumption per kg cement 0.7 litres 0.23–0.7 litres 0.15-0.7 litres 0.18-0.35 litres

Note - all consumption rates vary on set time and required use.


Pack Size 5 litres 5 litres 5 litres 5, 25 litres

30


Waterproofing

SikaSwell

2003 | 2010H | 2507H

SikaSwell Three t sealing profiles that swell in with water. They are permanently water resistant, highly elastic and pretreated to prevent premature swelling on site. SikaSwell Type 2003 2010H 2507H

Width 20mm 20mm 25mm

Thickness 3mm 10mm 7mm

Box 140m 50m 50m

Sika Injectoflex Sika Injectoflex Sika Injectoflex System (type HP) is an expanding, reinjectable hose for producing waterproof construction ts. Uses: Providing watertight ts for: Grade 2, 3 and 4 basements. Underground car parks. Water retaining structures. Sika Injectoflex Type Injectoflex

Components: Inner tube of non expanding black neoprene. 3 red external hydrophilic swelling strips. 3 yellow compressible sealing cords of foam rubber.

Size 40m

Hydrotite Hydrotite Hydrotite is the original expanding rubber used in a variety of applications for sealing ts against water penetration. Initially developed for sealing segmental concrete tunnel linings, Hydrotite is a compound of polychloroprene (Neoprene) and hydrophilic resin, which expands when in with water, providing a self-sealing and easy to use alternative to traditional methods. Ideal for water retaining structures to achieve watertight insitu concrete ts. Hydrotite Type CJ-0725 Adhesive

Size 10m coil 1 litre

Plug Plug A cementitious ready-mixed and rapid setting compound to plug leaks and stop water. DWI approved for use in with drinking water. Plug Type Vandex Plug

Size 15kg plastic, resealable bucket


Waterproofing Membranes PVC Internal and External Profiles PVC Internal and External Profiles PVC Waterstop profiles are designed for the use in basement, foundation and floor slab construction in both horizontal and vertical ts. External Expansion Incorporates a flat top centre box. External Construction Plain web section for use in contraction and construction ts. Centrebulb For use in expansion or contraction ts. Reinforced eyeleted outer flanges. Dumbell Plain web sections for use in construction and contraction ts, also incorporating eyeleted outer flanges. H.D. Centrebulb Range 10mm thick plain web sections for use in construction and contraction ts, also incorporating eyeleted outer flanges.

ting Pieces A full range of junction pieces are available.

Tools Jig and Knife Type ting Jig 110V Hot Knife Gas Heated Hot Knife


31

32

Waterproofing Membranes Cementitous Waterproofing This section covers products that are either coatings or in surface sealers which act as barriers to water ingress.

Products

Page

Thoroseal

33

Flexcrete 851

33

Fosroc Integra

34

SikaTop Sika Slurry

34 34

BB 75 Super

35 35

Waterproofing

Waterproofing

32


33

Cementitious Waterproofing Thoroseal Thoroseal THOROSEAL®, when mixed with water or a THORO ACRYL 60/ water blend (1 part THORO ACRYL 60 to 3 parts water) to a lump free consistency, provides a waterproof coating that is easily applied by brush or spray to concrete and masonry above and below ground level. Thoroseal Type Thoroseal

Size 25kg

Coverage 1st coat: 1.5kg/m2 2nd coat: 1.0kg/m2

Ancillaries Thoro Acryl 60 Thoro Acryl 60 is an acrylic polymer liquid additive for cement mixes, designed to enhance their physical characteristics, ease application and increase wear and weather resistance. Thoro Acryl 60 Size 5, 25 litres

Thoroseal Super Thoroseal Super When mixed with clean water Thoroseal Super forms an extremely durable waterproof coating for concrete and masonry. Applied with a brush or spray. Available in white and grey and in bags or pails. Resists both psitive and negative pressure. Thoroseal Super Type Thoroseal Super

Size 25kg

Coverage 2.5-3.5kg/m2 for two coats

Cementitious Coating 851 Cementitious Coating 851 Cementitious Coating 851 is a two component cementitious modified polymer coating which cures to form a hard, highly alkaline film with a degree of elasticity. It totally waterproofs concrete, stone, brickwork and blockwork even when subjected to negative and positive hydrostatic pressure tested at 10 bar. The standard 2mm thickness gives equivalent waterproofing to 1m of good quality concrete. This versatile coating has a range of applications including use in clean (DWI Aproved) and dirty water, basement waterproofing, tunnels and underground structures. It is widely specified for chloride protection and has an excellent international track record. Cementitious Coating 851 Type Cementitious Coating 851

Size 35kg pack


Yield 19.5 litres

Coverage 9.7m2/35kg at 2mm thickness

34

Cementitious Waterproofing

Waterproofing

Fosroc Integra Fosroc Integra Integra is an economic cementitious coating system for waterproofing concrete against positive and negative hydrostatic heads of water. Its uses include: sewage treatment and water treatment tanks, pipes, tunnels, manholes and below grade basements including retaining walls. Fosroc Integra Type Integra

Size 25kg

Coverage By brush: 1-1.5 kg/m2, By trowel: 2-2.5 kg/m2

SikaTop Seal 107 SikaTop Seal 107 SikaTop Seal 107 is a two component polymer modified cementitious waterproof mortar comprising of a liquid polymer and a special cement based mix incorporating ixtures. SikaTop Seal 107 Type SikaTop Seal 107

Size 10, 25kg

Colour Cement

Average Coverage 2.0kg/m2/mm

SikaTop 121 SikaTop 121 SikaTop 121 is a two-component thin layer waterproofing, leveling and bonding mortar. SikaTop 121 Type SikaTop 121

Size 10, 25kg

Average Coverage 2kg/m2/mm

Sika Damp Proofing Slurry Sika Damp Proofing Slurry Sika Damp Proofing Slurry is a one component flexible polymer modified cementitious dampproof product comprising of special cement based components and ixtures. When used with water a slurry or mortar material is produced for direct application to a variety of construction substrates. Sika Damp Proofing Slurry Type Sika Damp Proofing Slurry

Size 25kg

Average Coverage 6.5-7.5m2/bag @ 2mm thick


35

Cementitious Waterproofing BB 75 BB 75 Vandex BB 75 is a cementitious, ready for use (just add water), efflorescence-free surface waterproofer with hydrophobic properties, resistant to water and moisture. BBA approved (certificate no. 90/2516) and approved for use in with drinking water. BB 75 Type BB 75

Size 25kg PE-lined paper bag

Coverage 6kg/m2/3mm

BB 75 E BB 75 E Vandex BB 75 E is a cementitious two-component polymermodified and efflorescence-free surface waterproofer with hydrophobic properties, resistant to water and moisture. Made of Vandex BB 75 as a dry component and Vandex Elasticizer PK 75 as a liquid component, which provides elasticity and crack bridging properties. BB 75 E Type Size BB 75 (dry component) 25kg PE-lined paper bag Vandex Elasticizer PK 75 10kg PE-container

Coverage 6kg/m2/3mm

Super/Super White Super Vandex Super is a capillary-active cement based waterproofing slurry specifically designed for concrete waterproofing applications. It is based on grey Portland cement and is applied to concrete to provide in-depth waterproofing protection. BBA approved (certificate no. 04/4188) and approved for use in with drinking water. Super/Super White Type Size Vandex Super 25kg PE-lined paper bag


Coverage 1.5kg/m2

Products in this section are added to mixes to improve their ability to resist water. Some products also improve workability and strength.

Products

Page

Nitobond SBR

37

Site SBR

37

Sika 1 Sikacem 810

37 37

Ronafix ixtures Mix Designs

38

Waterproofing

Waterproofing

Waterproofing ixtures

38


37


Waterproofing

Nitobond SBR Nitobond SBR Additive for improving mortars for waterproofing repairs. Also used as a bonding agent for slip bricks, ceramic tiles etc. Nitobond Type Nitobond SBR

Size 5, 25 litre

Coverage As Slurry Primer = 2 to 3m2/litre For other uses SBR coverage is dependant on mix design.

Site SBR Site SBR Site SBR is a high performance but economic water resistant bonding agent for external rendering and screeds. It can be used as an ixture for concrete repair, brick slip and tile fixing mortars as well as an improving agent for resistance to abrasive chemicals and oils. Site SBR Type Site SBR

Size 5, 25 litres

Sika 1 Sika 1 Sika 1 mortars are prebatched kiln dried blends of specially graded aggregates and cements packaged in 4 grades at the appropriate mix ratios for optimum application performance and durability. When mixed with the diluted Sika 1 liquid waterproofing ixture they provide the multicoat components for the structural waterproofing and waterproof render systems. Sika 1 Type Sika 1 Waterproofer Spritz & bonding coat mortar Render mortar Screed mortar Finishing mortar

Size 5.25 litres 25kg bag 25kg bag 25kg bag 25kg bag

Cement/Aggregate Ratio n/a 1:1.0 1:1.5 1:2.5 1:3.5

SikaCem 810 SikaCem 810 SikaCem 810 is a patented one component water based acrylate bonding agent and integral mortar ixture. When diluted it produces a gauging solution for improving cementitious mixes. It should be added to water then mixed with cement and sand/aggregate to produce: Bond coat/slurry, Pourable micro concrete, Renders, Screeds with enhanced mechanical properties. SikaCem 810 Type SikaCem WWW.SU PPORTSITE.CO.U K

Size 25 litres

38


Waterproofing

Ronafix Ronafix Ronafix is a high performance site batched, Agrément Board certified, water based SBR polymer for producing waterproof renders. The cured mortar bonds monolithically to concrete and other surfaces and will resist both positive and negative pressure. Ronafix is used in swimming pools, tanks and basements to contain or exclude water. Ronafix Type Ronafix


Ronafix Mix Design Application Floor screeds and screed repairs Floor screeds and screed repairs Floor toppings and topping repairs Floor toppings and topping repairs Floating floor screeds Concrete repair Concrete repair Renders Renders Bedding brick slips, copings Fine concretes Slurry coats Mix Designs

Cement

A

By weight By volume By weight By volume By weight By volume By weight By volume By weight

By volume By weight By volume G By weight By volume Slurry By weight Coat By volume

A1 B B1 C, D &E F

Mix A A1 B B1 F D A E A C G SC

Thickness/notes 6mm – 50mm 26mm+ 15mm – 25mm 26mm+ 35mm+ over reinforcing steel no reinforcing steel watertight and tanking waterproof 6mm – 12mm typical 25mm+ typical 1mm – 3mm typical

6-3mm granite chips 75kg 1.25 -

10-5mm pea shingle -

10-5mm granite chips 75kg 1.25 -

Ronafix

Water (approx)

Yield m3 Coverage (approx) (approx)

50kg 1 50kg 1 50kg 1 50kg 1 50kg

Medium sharp sand 125kg 2 150kg 2.5 75kg 1.25 75kg 1.25 125kg

9 litres 1:1 with water 4.5 litres 1:3 with water 9 litres 1:1 with water 4.5 litres 1:3 with water 14 litres

9 litres 14 litres 9 litres 14 litres 4 litres

0.1 0.1 0.1 0.1 0.1

10m2 @10mm 10m2 @10mm 10m2 @10mm 7m2 @15mm 10m2 @10mm

1 50kg 1 50kg 1 50kg

2 150kg 2.5 100kg 1.5 50kg

-

100kg 1.5 -

-

3:1 with water 4.5 litres 1:3 with water 4.5 litres 1:3 with water 35 litres

13.5 litres 14 litres -

0.1 0.14 0.1

10m2 @10mm 5.6m2 @25mm 105-122m2

1

1

-

-

-

-

-

-

-


Waterproofing 4m2g48

Overview 26281t

More details 6y5l6z

Related Documents 3h463d

Waterproofing 4m2g48

Waterproofing 4m2g48

Waterproofing 4m2g48

Waterproofing 4m2g48

Detail Waterproofing 355n3c

05. Waterproofing 574y3z