Alcatel Bts Presentation 392t

Alcatel BTS EVOLIUM A9100 11 INTELTEC EMIRATES

FIROSE PADATH - INTELTEC

Logical position of BTS in BSS


22

Functional Architecture of BTS


33

Introduction of Alcatel BTS 44 INTELTEC EMIRATES


BTS Circuit Breakers (BCB) Network Interface Card

Indoor BTS

Shelf # 5

External Alarm Circuit Board (EACB)

Combiners Shelf # 4

Shelf # 3

TRE

Shelf # 2

SUMA Card

Shelf # 1


55

Interconnection Area BTSCA


Network Interface Card


BTS Circuit Breakers (BCB)

66

BTS Circuit Breakers (BCB)


77



88

Network Interface Card

Abis 1


99

The Abis Interface connects the BTS A9100 to the BSC. There are four connectors, these are Abis 1, 2, 3 and 4. Only Abis 1 and 2 are currently used; Abis 3 and 4 are provided for future use. Abis Relays - Four relays, one for each Abis Interface, are controlled by the SUM


1010

Lock Fastener

ANC Module – Antenna Network Combiner

Module Extractor

Equipment Label

Transmitter Connector

Antenna Connector

Receiver Connector


1111

Click to edit Master text styles Second level ● Third level ● Fourth level ● Fifth level

The ANC (Antenna Network Combiner) provides the intermediate RF stage between the TREs and the antenna. Its tasks are to: - Combine the output signals of up to four transmitters and to connect them to up to two antennas - Feed the received signals from the antenna to the radio front end, where the signals are amplified and distributed to up to eight receivers - Allow simultaneous transmission and receiving on antennas (duplexer)

- Provide filtering for the TX- and RX-path FIROSE PADATH - INTELTEC 1212

Click to edit Master text styles Second level ● Third level ● Fourth level ● Fifth level

On the downlink, the ANC connects two TRE transmitters to two antennas. On the uplink, it splits the received signals and es them to the TRE receivers. ANCG, ANC module for GSM 900 ANCD, ANC module for GSM 1800


1313

Lock Fastener

ANY Module

Transmitter Connector

Equipment Label

Module Extractor

Receiver Connector

Antenna Connector


1414

ANY Module

The ANY is a ive RF module, having neither a controller nor a power supply. It is an optional RF distribution device, which is used to expand the capacity of the ANX/ANC. Therefore, it is basically an extension unit to the ANX/ANC module. ANYG, ANY module for GSM 900 ANYD, ANY module for GSM 1800


1515

ANY Module

The Twin Wide Band Combiner stage (ANY) combines up to four transmitters into two outputs, and distributes the two received signals up to four receivers Twin Wide Band Combiner module (ANY) is only necessary for sectors with five or more TRXs


1616

TRE Module Module Extractor Transmitter Connector

Equipment Label

ON/OFF Switch

USB Test Connector Receiver Connector

LEDs Lock Fastener


1717

TRE Module


1818

TRE Module

The TRE performs the digital functions interface to the SUM and the analog functions interface to the AN module Interface Test Provides an interface to the TRE for factory test purposes. TX Provides the transmit RF Interface to the AN module. RX 0, RX 1 Provides two receive RF Interfaces from the AN module. FIROSE PADATH - INTELTEC

1919

SUMA/SUMP -Station Unit Module

BTS Connection Area Connector

Abis ½ Connector Equipment Label BTS Terminal Connector Test Connector USB Connector

LEDs


Lock Fastener

2020

SUMA/SUMP


2121

The SUMP/SUMA provides the central management and control of all the BTS A9100 modules. It is responsible for the following functional areas: -Digital transmission -Timing and clock generation -Management of the BTS internal digital interfaces O and M functions The SUMP/SUMA provides a switchable 2 Mbit/s duplex connection between the Abis Interface and the BSII. The BSII is used to transfer TCH information to the TRE module, and O and M information to the OMU/SUM microprocessor. The Abis Interface is the digital interface to the BSC

The Q1 link is a logical link routed via the Abis Interface, the Time Slot Switch, the BSII switch and the BSII to the O and M functions. The O and M functions are performed remotely by the BSC TSC, via the Q1 link, or locally via aBTS Terminal. All BTS A9100 transmission equipment have Q1 addresses, which identify them to the TSC. The BSII is an internal digital interface to the TRE module


2222

SUMA Card Basic Architecture


2323

Remote Inventory Cable (RI Cable)


2424

Remote Inventory Cable (RI Cable)


2525

Cabinet Cooling Fan


2626

Connect to Alcatel BTS Using BTSTerminal FIROSE PADATH - INTELTEC

2727

Name (COMMTE)

(COMMTE)


2828

Press Baud rate button to set it


2929

Select the appropriate COM Port

Select Baud rate = 19200


3030

Press F2 OR “Connect/Disconnect” button OR File>Connect/Disconnect from menu


3131

Menu bar will be changed on establishing successful connection

Following windows will open on establishing successful connection


3232

Monitor Active Alarm

External Active Alarms Show Here


3333

Show Hardware Configuration (Ctrl H)

Select All

Select Appropriate Module

Select OK


3434

SUMA Card = OMU 1

Rack A (BTS Cabinet # 1)

Shelf # 2

Slot # 7


3535

SBL Module States (F5)

SBL Module States (F5)

Antenna 0=A

Antenna 1=B

RA 1= Combiner 1 Sector A

VSWR Value=1.1 VSWR Value=1.2


3636

SBL Management

Read

Initializ e

SBL Management

Select Module


Reset

Disable Restart

3737

Execution Result

Selected Module Type


State of the Module (NEQ/OPR/IT)

3838

Modify Hardware Configuration

Remove Module

End Modification of HW Configuration

Select Module to Remove


3939

Following window appears (Cabling Detection in Progress)

Click Yes


4040

OFF Line Commissioni ng Procedure FIROSE PADATH - INTELTEC

4141

Switch OFF the BTS cabinet and disconnect Abis connectors from DDF before offline start


4242

Disconnect the Abis connector from The DDF


4343

Switch ON the BTS cabinet breakers and connect the Laptop at the BTS Terminal using MMI Cable


4444

Name (COMMTE)

(COMMTE)


4545

Press F2 OR “Connect/Disconnect” button OR File>Connect/Disconnect from menu


4646

Menu bar will be changed on establishing successful connection

Following windows will open on establishing successful connection


4747

Restore Default

Warning Window appears Click OK to Restore SUMA Card


4848

Qmux address Press “Yes” to change it Confirm Qmux address from OMCR first- INTELTEC FIROSE PADATH

4949

Go to Commissioning->>BTS-SW to BTS software


5050

Edit New Qmux address Press “Put” button to update


5151

Updating Qmux address


5252

Press Browse to select the path of “BM1SAW19.MSF” file

Press Browse to select the path of “AGC3AVWa.DDL” file

Path Selection Window


5353

Software in Progress It may take up to 30 minutes


5454

Initialization window open when complete


5555

Receiving data window open


5656

Select appropriate option from Frequency Brand dropdown menu 1- Select GSM for GSM cabinet 2- Select DCS1800 for DCS cabinet 3- Select GSM for GSM+DCS (Combined) cabinet


5757

Don’t uncheck Bridge check option and don’t change Sectors numbers Press “Save” button in Sector mapping window


5858

Updating flash


5959

Press Save in TMA Setting window


6060

Press Settings->Transmission->Initial Settings


6161

Check Line impedance for Abis1 & Abis2 = 75ohm

Reconfirm the Qmux address Environment Abis1 = Chain – end position

Baud Rate = 1200

CRC Check = ON


6262

Press Settings->Transmission->Board Settings


6363

Uncheck all TREs press “Transmit” button


6464

Press Commissioning->Initialization->All Sectors to initialize BTS


6565

Initialization of Commissioning in progress


6666

Press Commissioning->Station Unit Test for Station Unit Test


6767

Select “Internal Loop”


6868

“Station Unit Test” in progress


6969

Following Results on successful completion


7070

Select External Loop (Make Sure that the Abis # or 2 must be looped at DDF


7171

Abis # 1 Loop test failed because Abis # 1 not Looped at DDF

Result window appears


7272

Now switch on the BTS cabinet breakers and through the site


7373

Reconnect the Abis connector at DDF by ing the TX/RX cables properly

Reconnect the Abis connector at DDF by ing the TX/RX cables properly


7474

OFF Line Commissioning is Done Successfully


7575

AN

Alcatel Glossary A

Antenna Network B BCB BTS Control Bus BSII Base Station Controller BSS Base Station Subsystem BTS Base Station Transceiver BTSW BTS-Terminal for Windows FIROSE PADATH - INTELTEC

7676

Alcatel Glossary

C CCF Cabinet Cooling Fan CDM Configuration Data Message CLEI Common Language Equipment CLLK Clock Link F Configuration Parameter File CRC Cyclic Redundancy Check CU Carrier Unit FIROSE PADATH - INTELTEC

7777

Alcatel Glossary D DC Direct Current DMA Deferred Maintenance Alarm E EQU Equipped


7878

Alcatel Glossary

F FIA Format Identifier for Application part of RI FIM Format Identifier Manufacturing FIT Faulty In Traffic FLT Faulty FOS Faulty Out of Service FIROSE PADATH - INTELTEC

7979

Alcatel Glossary

I ICS Item Change Status IT In Traffic L LDA Local Defence Action LRA Local Recovery Action


8080

Alcatel Glossary

MI MSA MSD NEQ NOP

M Maintenance Information MSD Auto Maintenance Seized N Not Equipped Not Operational FIROSE PADATH - INTELTEC

8181

Alcatel Glossary

O O&M Operation and Maintenance OMU Operation and Maintenance Unit OMUA OMU A RIT OMUB OMU B RIT OP Operational OPR Operator FIROSE PADATH - INTELTEC

8282

Alcatel Glossary

P PADD Physical Address PMA Prompt Maintenance Alarm R RA Radio Access RF Radio Frequency RFH Radio Frequency Hopping ( also known as : Synthesizer Hopping ) RI Remote Inventory RIT Replaceable Item RX Receiver or receive ..... RTC Remote Tunable Combiner FIROSE PADATH - INTELTEC

8383

Alcatel Glossary

S SBL Security Block Level SCFE Station Unit Control Function Entity RIT SOS System Out of Service SUM Station Unit Module SUMP SUM PCM RIT SW Software FIROSE PADATH - INTELTEC

8484

Alcatel Glossary

T TLV Tag, Length, Value TRE Transceiver Module (combined Transmitter / Receiver functionality for base band and RF signals) TS Timeslot TX Transmitter or transmit ..... FIROSE PADATH - INTELTEC

8585

Alcatel Glossary

VPMA VSWR WBC WTC XBCB XCLK XIOB

V Very Prompt Maintenance Alarm Voltage Standing Wave Ratio W Wide Band Combiner Wait Traffic Clear X External BCB External Clock External Input Output Board FIROSE PADATH - INTELTEC

8686

The End Firose Padath Inteltec


8787

Alcatel Bts Presentation 392t

Overview 26281t

More details 6y5l6z

Related Documents 3h463d

Alcatel Bts Presentation 392t

Alcatel Bts Presentation Using B10 4z6n4h

Alcatel Bts 4us14

Alcatel Bts 4us14

Alcatel Bts Discription 2gz6p

Alcatel Bts Hardware Description 6q145g