Cadena 4k2a6c
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report 3i3n4
Overview 26281t
& View Cadena as PDF for free.
More details 6y5l6z
- Words: 8,037
- Pages: 17
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80) ®
HERC-ALLOY 800 CHAIN WORKING LOAD LIMIT: 2,100 TO 72,300 LBS. BENEFITS & FEATURES ƒ A higher strength heat treated alloy steel chain primarily used as a sling component for overhead lifting ƒ Can be used in rigging and tie down applications where a lighter weight, higher strength chain is desirable ƒ Recommended for overhead lifting by NACM, ASME, and OSHA B
C 1000
A
Nominal Chain Dimensions (in.)
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
Chain Size (in.)
Working Load Limit (lbs.)
7/32 9/32 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4
2,100 3,500 4,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
Per Foot
Per Drum
Material Diameter A
Inside Length B
Inside Width C
Product Code
Weight (lbs./ft.)
Approximate Number of Links (per ft.)
Product Code
Length (ft.)
Weight (lbs.)
0.22 0.28 0.32 0.39 0.51 0.63 0.79 0.88 1.00 1.25
0.68 0.88 1.02 1.25 1.44 1.78 2.23 2.25 3.07 3.92
0.31 0.40 0.46 0.57 0.73 0.86 1.07 1.14 1.49 1.74
607020 607028 607031 607037 607050 607062 607075 607087 607101 607128
0.44 0.73 0.91 1.44 2.55 3.82 5.95 7.76 9.41 14.20
17.8 13.6 11.8 9.6 8.3 6.8 5.4 5.3 3.9 3.1
677010 677011 – 677013 677015 677016 677017 677018 677019 677070
800 500 – 500 300 200 100 100 100 90
354 365 – 719 765 765 595 776 941 1,278
INSPECTION, CARE & USE HOW TO SELECT AND ORDER THE PROPER CHAIN SLING 1. Determine the weight and configuration of the load(s) to be lifted. 2. Determine the type of chain sling required, according to weight and configuration. (See page 31 for standard sling configurations.) 3. Determine the size of the body chain according to the working load limits. Be sure to take into consideration the effect of the required angle. The working load limit is the maximum load in pounds which should be applied in direct tension to a straight length of chain. Note: Working load limit can be affected by angles of loading, type of hitch used, environmental conditions such as hot and cold temperatures, and D/d ratio. 4. Determine the reach required to give the desired angle. The reach is measured from the upper bearing surface of the master link to the bearing surface of the lower attachment. If chain slings are to be used in pairs and are to be matched for reach, please indicate when ordering. 5. Know share of load on pick points and location of center of gravity. See pages 26 through 32 for more information, or visit us at www.cmworks.com
74
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80) ®
HERC-ALLOY 800 CHAIN SLINGS
SINGLE ENDLESS
DOUBLE DOUBLE (2 LEGS)
DOUBLE ENDLESS
TRIPLE (3 LEGS)
SINGLE BASKET
MAGNET MAGNET SLING
QUADRUPLE (4 LEGS)
SINGLE ADJUSTABLE
DOUBLE BASKET
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
SINGLE SIN NGLE LEG LEG (VERTICAL)
DOUBLE ADJUSTABLE
Adjusters on slings allow for easy and safe take up of chain when applications require shorter leg lengths or when lifting objects of abnormal sizes. There are two styles of adjusters: Style A and Style B. Style A is commonly used for shorter reach slings and consists of a hook attached to the link. Style B has 12" of chain in between link and hook gives you more flexibility on longer slings. Note: Adjusters are also available on single, double, triple and quad slings. Working Load Limits for Sling Types Show Above Chain Size (in.)
7/32 9/32 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4
Single (1 leg)
Single Choker
90º (lbs.)
90º (lbs.)
60º (lbs.)
45º (lbs.)
30º (lbs.)
60º (lbs.)
45º (lbs.)
30º (lbs.)
60º (lbs.)
45º (lbs.)
2,100 3,500 4,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
1,700 2,800 3,600 5,700 9,600 14,500 22,600 27,400 38,200 57,800
3,600 6,100 7,800 12,300 20,800 31,300 49,000 59,200 82,600 125,200
3,000 4,900 6,400 10,000 17,000 25,600 40,000 48,400 67,400 102,200
2,100 3,500 4,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
5,500 9,100 11,700 18,400 31,200 47,000 73,500 88,900 123,900 187,800
4,400 7,400 9,500 15,100 25,500 38,400 60,000 72,500 101,200 153,400
3,200 5,200 6,800 10,600 18,000 27,100 42,400 51,300 71,500 108,400
5,500 9,100 11,700 18,400 31,200 47,000 73,500 88,900 123,900 187,800
4,400 7,400 9,500 15,100 25,500 38,400 60,000 72,500 101,200 153,400
Double (2 legs)
Triple (3 legs)
Single Basket
Double Basket
Single Endless
Double Endless
30º (lbs.)
60º (lbs.)
60º (lbs.)
90º (lbs.)
60º (lbs.)
3,200 5,200 6,800 10,600 18,000 27,100 42,400 51,300 71,500 108,400
3,600 6,100 7,800 12,300 20,800 31,300 49,000 59,200 82,600 125,200
5,500 9,100 11,700 18,400 31,200 47,000 73,500 88,900 123,900 187,800
2,100 3,500 4,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
3,600 6,100 7,800 12,300 20,800 31,300 49,000 59,200 82,600 125,200
Quad (4 legs)
American Society of Mechanical Engineers ASME B30.9, the National Association of Chain Manufacturers (NACM) and the Occupation Safety & Health istration (OSHA) recommend only the use of alloy steel chain for overhead lifting, i.e. sling chain. Slings may be constructed by the using Herc-Alloy® chain, Herc-Alloy 1000 or Herc-Alloy 800 chain and attachments.
For more information on standard sling configurations, see page 31 or visit us online at www.cmworks.com
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
75
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80)
MASTER LINK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 3,600 TO 187,800 LBS. BENEFITS & FEATURES ƒ ƒ ƒ ƒ
Accepts both Herc-Alloy® 1000 & 800 chain and components Durable orange powder coated finish May be used for mechanical and welded sling assemblies 100% proof tested
B
A
C
Trade Size (in.)
Working Catalog Load Limit Number (lbs.)
Product Code
Nominal Dimensions (in.) Material Diameter A
Inside Length B
Inside Width C
Weight (lbs.)
Type and Size of Grade 80 Chain Sling (in.) Single
Double
Standard Sizes (DUAL RATED THROUGH 1-3/4" SIZE ONLY)
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
3/8 1/2 3/4 1 1-1/4 1-1/2 1-3/4 2* 2-1/4* 2-3/4*
5,400 8,600 17,600 30,000 45,200 70,600 105,900 88,900 125,200 187,800
HA40 HA50 HA75 HA100 HA125 HA150 HA175 HA200 HA225 HA275
555231 555232 555235 555238 555240 555243 555246 554949 554951 554957
0.41 0.56 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.75
3.00 5.00 5.50 7.00 8.75 10.50 12.00 14.00 16.00 16.00
1.50 2.50 2.75 3.50 4.38 5.25 6.00 7.00 8.00 9.00
0.33 1.02 2.08 4.59 9.31 15.60 24.40 38.00 55.00 84.84
7/32 & 9/32 3/8 1/2 5/8 & 3/4 7/8 1 1-1/4 1-1/4 – –
7/32 9/32 3/8 1/2 5/8 3/4 & 7/8 1 1 1-1/4 –
554969 554942 554944 554970 554945 554952
1.00 1.25 1.50 1.50 1.75 2.00
8.00 12.00 14.00 12.00 14.00 16.00
4.00 6.00 7.00 6.00 7.00 8.00
5.25 12.08 20.16 17.60 27.92 43.00
N/A
N/A
Can be used with included angles up to 120°
120º
Special Sizes (NOT DUAL RATED) 1 1-1/4 1-1/2 1-1/2 1-3/4 2
18,200 22,800 36,700 42,900 57,100 77,800
N/A
NOTE: Standard sizes dual rated through 1-3/4" only. Special sizes not dual rated.
FORGED MASTER LINK GRADE 80 WORKING LOAD LIMIT: 5,100 TO 20,400 LBS. D
BENEFITS & FEATURES ƒ ƒ ƒ ƒ ƒ
Quench and tempered alloy steel Fatigue rated to Grade 80 specifications 100% proof tested Raised markings for better identification Durable orange powder coated finish
Can be used with included angles up to 120°
B
120º
C
76
A
Nominal Dimensions (in.)
Trade Size (in.)
Working Load Limit (lbs.)
Product Code
Material Diameter A
Inside Length B
Inside Width C
Weight (lbs.)
1/2 5/8 3/4 1
5,100 7,700 10,600 20,400
M50P M62P M75P M100P
0.50 0.63 0.75 1.00
5.00 6.00 6.00 8.00
2.50 3.00 3.00 4.00
0.90 1.75 2.35 6.00
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80)
MASTER LINK WITH & WITHOUT FLATS HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 4,200 TO 327,800 LBS. BENEFITS & FEATURES
Flat
ƒ Designed to accept HA800 chain, wire rope and synthetic attachments ƒ Use with mechanical and welded assemblies ƒ Sizes up to 1-1/4" available with flats to accommodate Omega link ƒ 100% proof tested ƒ Extra wide body makes these links ideal for wire rope applications and use with Omegaloks. Master link with flat allows for easy installation of these attachments.
Can be used with included angles up to 120°
With Chain
With Wire Rope & Synthetics
7/16
4,200
3,360
1/2
5,750
4,600
5/8
9,000
7,200
3/4
14,200
11,360
7/8
17,300
13,840
1
26,500
21,200
1-1/4
37,400
29,920
1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4
53,000 72,150 94,200 119,200 147,150 178,050
42,400 57,720 75,360 95,360 117,720 142,440
Nominal Dimensions (in.) Product Code
Material Diameter A
Inside Length B
Inside Width C
0.44
4.13
2.29
0.56
4.84
2.69
0.63
5.29
2.98
0.75
6.61
3.72
0.88
7.35
4.14
ML040 ML040NF ML050 ML050NF ML063 ML063NF ML075 ML075NF ML087 ML087NF ML100 ML100NF ML125 ML125NF ML150 ML175 ML200 ML225 ML250 ML275
1.00
7.53
Flat Dimensions (in.)
4.30
1.25
9.26
5.29
1.50 1.75 2.00 2.25 2.50 2.75
11.03 12.86 14.70 16.54 18.38 20.21
6.30 7.35 8.40 9.45 10.50 11.55
Width
Thickness
0.94 – 0.94 – 1.22 – 1.41 – 1.56 – 1.56 – 1.56 – – – – – – –
0.28 – 0.28 – 2.81 – 0.40 – 0.44 0.53 0.68 – – – – – – –
Type and Size of Chain Sling (in.) Weight (lbs.)
Single
Double
0.50
7/32 & 9/32
7/32
1.02
–
7/32
1.34
3/8
9/32
2.36
1/2
3/8
3.60
–
–
5.20
5/8
1/2
9.60
3/4 & 7/8
5/8
16.20 25.10 41.00 58.00 74.90 99.80
1 – 1-1/4 – – –
3/4 7/8 1 – 1-1/4 –
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
Working Load Limit (lbs.)
A
C
120º
Trade Size (in.)
B
NOTE: *Master link with flats are available through 1-1/4" only Part numbers with"NF" are for master links WITHOUT flats
FLAT BOTTOM MASTER LINK GRADE 80 WORKING LOAD LIMIT: 73,500 TO 187,800 LBS. C
BENEFITS & FEATURES ƒ ƒ ƒ ƒ
Designed to accept HA800 chain and components Made from alloy steel Extra wide width allows for larger hook usage 100% proof tested
Chain Size (in.) 5/8 & 3/4 7/8 & 1 1 & 1/4
Trade Size Working Load Limit (in.) (lbs.) 1-3/4 2 2-1/2
73,500 123,900 187,800
Product Code 554966 554950 554965
B
A
Nominal Dimensions (in.) Material Diameter A
Inside Length B
Inside Width C
1.75 2.00 2.50
8.00 8.98 11.92
5.000 5.000 6.500
Weight (lbs.) 18.96 28.04 54.73
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
77
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80)
SUB-ASSEMBLY DUAL RATED FOR USE WITH HA800 800 & HA1000 WORKING LOAD LIMIT: 7,000 TO 187,800 LBS. C
BENEFITS & FEATURES
A
ƒ Accepts both Herc-Alloy 1000 ƒ Designed for triple and quad & 800 chain and components branch Herc-Alloy® chain slings ƒ Durable orange powder ƒ Consists of an oblong master coated finish link and two welded master coupling links ƒ May be used for mechanical or welded sling assemblies ƒ 100% proof tested
B
120º E
Can be used with included angles up to 120° F
D
Trade Size (in.)
ensions (in.) Siz of Chain Sling (in.) Master Link Nominal Dimensions (in.) Intermediate Link Nominal Dimensions Type & Size Working Catalog Load Limit Product Weight Material Inside Inside Material Inside Inside Number at 60º Code (lbs.) Diameter Length Width Diameter Length Width Triple Quad (lbs.) A B C D E F
1/2 3/4 1 1-1/4 1-1/2 1-3/4 2* 2-1/4* 2-3/4*
SA50 SA75 SA100 SA125 SA150 SA175 HA200-SA HA225-SA HA275-SA
7,000 11,200 22,900 39,000 58,700 91,700 88,900 123,900 187,800
555274 555275 555276 555277 555278 555279 554980 554981 554983
0.56 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.75
5.00 5.50 7.00 8.75 10.50 12.00 14.00 16.00 16.00
2.50 2.75 3.50 4.38 5.25 6.00 7.00 8.00 9.00
0.44 0.47 0.78 0.91 1.13 1.50 1.53 1.78 2.00
1.75 1.56 2.63 3.13 4.00 5.25 5.25 6.00 7.00
1.06 0.88 1.50 1.75 2.25 2.75 2.75 3.00 3.50
1.35 2.64 7.25 13.51 24.28 44.58 57.34 81.48 126.66
7/32 9/32 3/8 1/2 5/8 3/4 & 7/8 7/8 1 1-1/4
7/32 9/32 3/8 1/2 5/8 3/4 & 7/8 7/8 1 1-1/4
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
* Grade 80 only
WIDE BODY SUB-ASSEMBLY WITH FLATS HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 4,600 TO 178,050 LBS. BENEFITS & FEATURES ƒ Extra wide body is ideal for wire rope applications ƒ Sizes up to 1-1/4" intermediate links available with flats to accommodate Omega links
C A
Can be used with included angles up to 120°
E
F
Trade Size (in.) 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4
Working Load Limit (lbs.) With Chain 5,750 9,000 14,000 17,300 26,500 37,400 53,000 72,150 94,200 119,200 147,150 178,050
Complete Assembly With Wire Product Code Rope & Synthetic 4,600 7,200 11,200 13,840 21,200 29,920 42,400 57,720 75,360 95,360 117,720 142,400
SA050 SA063 SA075 SA087 SA100 SA125 SA150 SA175 SA200 SA225 SA250 SA275
120º
B
Flat
ƒ Designed to accept Herc-Alloy 800® chain, wire rope and synthetic attachments ƒ Durable orange powder coated finish ƒ 100% proof tested ƒ May be used for mechanical and welded sling assemblies
Master Link Nominal Dimensions (in.) Product Code
Material Diameter A
Inside Length B
Inside Width C
ML050 ML063 ML075 ML087 ML100 ML125 ML150 ML175 ML200 ML225 ML250 ML275
0.56 0.63 0.75 0.88 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75
4.84 5.29 6.61 7.35 7.53 9.26 11.03 12.86 14.70 16.54 18.38 20.21
2.69 2.98 3.72 4.14 4.30 5.29 6.30 7.35 8.40 9.45 10.50 11.55
D
Intermediate Link Nominal Dimensions (in.) Product Code
Material Diameter D
Inside Length E
Inside Width F
ML040 ML050 ML063 ML063 ML075 ML100 ML100 ML125 ML150 ML175 ML200 ML200
0.44 0.56 0.63 0.63 0.75 1.00 1.00 1.25 1.50 1.75 2.00 2.00
4.13 4.84 5.29 5.29 6.61 7.53 7.53 9.26 11.03 12.86 14.70 14.70
2.29 2.69 2.98 2.98 3.72 4.30 4.30 5.29 6.30 7.35 8.40 8.40
Weight (lbs.)
1.8 2.9 5.5 6.3 10.2 20.0 26.6 44.3 73.4 108.2 156.9 181.0
Type and Size of Chain Sling (in.) Triple
Quad
– 7/32 9/32 – 3/8 1/2 – 5/8 3/4 7/8 1 –
– 7/32 9/32 – 3/8 1/2 – 5/8 3/4 7/8 1 –
NOTE: Master link with flats are available through 1-1/4" only
78
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
RIGGING HARDWARE
MASTER LINK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 3,600 TO 187,800 LBS. BENEFITS & FEATURES ƒ ƒ ƒ ƒ
Accepts both Herc-Alloy® 1000 & 800 chain and components Durable orange powder coated finish May be used for mechanical and welded sling assemblies 100% proof tested
B
C
Trade Size (in.)
Working Catalog Load Limit Number (lbs.)
Product Code
Nominal Dimensions (in.) Material Diameter A
Inside Length B
Inside Width C
Weight (lbs.)
A
Type and Size of Grade 80 Chain Sling (in.) Single
Double
Standard Sizes (DUAL RATED THROUGH 1-3/4" SIZE ONLY) 3/8 1/2 3/4 1 1-1/4 1-1/2 1-3/4 2* 2-1/4* 2-3/4*
5,400 8,600 17,600 30,000 45,200 70,600 105,900 88,900 125,200 187,800
HA40 HA50 HA75 HA100 HA125 HA150 HA175 HA200 HA225 HA275
555231 555232 555235 555238 555240 555243 555246 554949 554951 554957
0.41 0.56 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.75
3.00 5.00 5.50 7.00 8.75 10.50 12.00 14.00 16.00 16.00
1.50 2.50 2.75 3.50 4.38 5.25 6.00 7.00 8.00 9.00
0.33 1.02 2.08 4.59 9.31 15.60 24.40 38.00 55.00 84.84
7/32 & 9/32 3/8 1/2 5/8 & 3/4 7/8 1 1-1/4 1-1/4 – –
7/32 9/32 3/8 1/2 5/8 3/4 & 7/8 1 1 1-1/4 –
554969 554942 554944 554970 554945 554952
1.00 1.25 1.50 1.50 1.75 2.00
8.00 12.00 14.00 12.00 14.00 16.00
4.00 6.00 7.00 6.00 7.00 8.00
5.25 12.08 20.16 17.60 27.92 43.00
N/A
N/A
Can be used with included angles up to 120°
120º
1 1-1/4 1-1/2 1-1/2 1-3/4 2
18,200 22,800 36,700 42,900 57,100 77,800
N/A
® HERC-ALLOY 800 RIGGING HARDWARE
Special Sizes (NOT DUAL RATED)
NOTE: Standard sizes dual rated through 1-3/4" only. Special sizes not dual rated.
FORGED MASTER LINK GRADE 80 WORKING LOAD LIMIT: 5,100 TO 20,400 LBS. D
BENEFITS & FEATURES ƒ ƒ ƒ ƒ ƒ
Quench and tempered alloy steel Fatigue rated to Grade 80 specifications 100% proof tested Raised markings for better identification Durable orange powder coated finish
Can be used with included angles up to 120°
B
120º
C
A
Nominal Dimensions (in.)
Trade Size (in.)
Working Load Limit (lbs.)
Product Code
Material Diameter A
Inside Length B
Inside Width C
Weight (lbs.)
1/2 5/8 3/4 1
5,100 7,700 10,600 20,400
M50P M62P M75P M100P
0.50 0.63 0.75 1.00
5.00 6.00 6.00 8.00
2.50 3.00 3.00 4.00
0.90 1.75 2.35 6.00
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
93
RIGGING HARDWARE
MASTER LINK WITH & WITHOUT FLATS HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 3,360 TO 178,050 LBS. BENEFITS & FEATURES
Flat
ƒ Designed to accept HA800 chain, wire rope and synthetic attachments ƒ Use with mechanical and welded assemblies ƒ Sizes up to 1-1/4" available with flats to accommodate Omega link ƒ 100% proof tested ƒ Extra wide body makes these links ideal for wire rope applications and use with Omegaloks. Master link with flat allows for easy installation of these attachments.
B
Can be used with included angles up to 120°
A
C
120º
Working Load Limit (lbs.) Trade Size (in.)
With Chain
With Wire Rope & Synthetics
7/16
4,200
3,360
1/2
5,750
4,600
5/8
9,000
7,200
3/4
14,200
11,360
7/8
17,300
13,840
1
26,500
21,200
RIGGING HARDWARE
1-1/4
37,400
29,920
1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4
53,000 72,150 94,200 119,200 147,150 178,050
42,400 57,720 75,360 95,360 117,720 142,440
Nominal Dimensions (in.) Product Code
Material Diameter A
Inside Length B
Inside Width C
0.44
4.13
2.29
0.56
4.84
2.69
0.63
5.29
2.98
0.75
6.61
3.72
0.88
7.35
4.14
ML040 ML040NF ML050 ML050NF ML063 ML063NF ML075 ML075NF ML087 ML087NF ML100 ML100NF ML125 ML125NF ML150 ML175 ML200 ML225 ML250 ML275
1.00
7.53
4.30
1.25
9.26
5.29
1.50 1.75 2.00 2.25 2.50 2.75
11.03 12.86 14.70 16.54 18.38 20.21
6.30 7.35 8.40 9.45 10.50 11.55
Flat Dimensions (in.) Width
Thickness
0.94 – 0.94 – 1.22 – 1.41 – 1.56 – 1.56 – 1.56 – – – – – – –
0.28 – 0.28 – 2.81 – 0.40 – 0.44 0.53 0.68 – – – – – – –
Type and Size of Chain Sling (in.) Weight (lbs.)
Single
Double
0.50
7/32 & 9/32
7/32
1.02
–
7/32
1.34
3/8
9/32
2.36
1/2
3/8
3.60
–
–
5.20
5/8
1/2
9.60
3/4 & 7/8
5/8
16.20 25.10 41.00 58.00 74.90 99.80
1 – 1-1/4 – – –
3/4 7/8 1 – 1-1/4 –
NOTE: *Master link with flats are available through 1-1/4" only Part numbers with"NF" are for master links WITHOUT flats
94
C H A I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
RIGGING HARDWARE
WIDE BODY SUB-ASSEMBLY WITH FLATS HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 4,600 TO 178,050 LBS. C A
BENEFITS & FEATURES
Trade Size (in.) 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4
ƒ 100% proof tested ƒ May be used for mechanical and welded sling assemblies ƒ Extra wide body is ideal for wire rope applications ƒ Sizes up to 1-1/4" intermediate links available with flats to accommodate Omega links
Working Load Limit (lbs.) With Chain 5,750 9,000 14,000 17,300 26,500 37,400 53,000 72,150 94,200 119,200 147,150 178,050
Complete Assembly With Wire Product Rope & Code Synthetic 4,600 7,200 11,200 13,840 21,200 29,920 42,400 57,720 75,360 95,360 117,720 142,400
SA050 SA063 SA075 SA087 SA100 SA125 SA150 SA175 SA200 SA225 SA250 SA275
B 120º
E Can be used with included angles up to 120°
Flat
ƒ Designed to accept Herc-Alloy 800® chain, wire rope and synthetic attachments ƒ Durable orange powder coated finish
F
Master Link Nominal Dimensions (in.)
D
Intermediate Link Nominal Dimensions (in.)
Product Code
Material Diameter A
Inside Length B
Inside Width C
Product Code
Material Diameter D
Inside Length E
Inside Width F
ML050 ML063 ML075 ML087 ML100 ML125 ML150 ML175 ML200 ML225 ML250 ML275
0.56 0.63 0.75 0.88 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75
4.84 5.29 6.61 7.35 7.53 9.26 11.03 12.86 14.70 16.54 18.38 20.21
2.69 2.98 3.72 4.14 4.30 5.29 6.30 7.35 8.40 9.45 10.50 11.55
ML040 ML050 ML063 ML063 ML075 ML100 ML100 ML125 ML150 ML175 ML200 ML200
0.44 0.56 0.63 0.63 0.75 1.00 1.00 1.25 1.50 1.75 2.00 2.00
4.13 4.84 5.29 5.29 6.61 7.53 7.53 9.26 11.03 12.86 14.70 14.70
2.29 2.69 2.98 2.98 3.72 4.30 4.30 5.29 6.30 7.35 8.40 8.40
Weight (lbs.) 1.8 2.9 5.5 6.3 10.2 20.0 26.6 44.3 73.4 108.2 156.9 181.0
Type and Size of Chain Sling (in.) Triple
Quad
– 7/32 9/32 – 3/8 1/2 – 5/8 3/4 7/8 1 –
– 7/32 9/32 – 3/8 1/2 – 5/8 3/4 7/8 1 –
NOTE: Master link with flats are available through 1-1/4" only
® HERC-ALLOY 800 RIGGING HARDWARE
DNV MASTER SUB-ASSEMBLIES WORKING LOAD LIMIT: 17-1/2 TO 50 TON
Master Sub-Assemblies meeting DNV requirements are used to build slings in conjunction with DNV Shackles. These products are designed for use in offshore saltwater environments for general load securement applications, such as during the installation and removal of offshore platforms or transportation of cargo container units.
Working Load Limit
ƒ Designed for use with chain, wire rope and synthetic slings. ƒ Made from superior triple alloy steel with th a galvanized coating for protection against corrosion. th ƒ Certification of compliance supplied with each shipment. CG3 documentation available upon request. ƒ Available in sizes from 1-1/4" to 2" diameter. meter. Other sizes available upon request.
Master Link Dimensions (in.)
C A
Intermediate Link Dimensions (in.)
Trade Size (in.)
ton
lbs.
Product Code
Material Diameter A
Inside Length B
Inside Width C
Material Diameter D
Inside Length E
Inside Width F
Weight (lbs.)
1-1/4 1-1/2 1-3/4 2
17.64 27.56 38.59 50
35,280 55,125 77,175 100,000
SA125DNV SA150DNV SA175DNV SA200DNV
1.25 1.50 1.75 2.00
8.75 10.50 12.00 14.00
4.38 5.25 6.00 7.00
1.25 1.50 1.75 2.00
8.75 10.50 12.00 14.00
4.38 5.25 6.00 7.00
27.8 48.0 75.0 113.7
B E Flat
BENEFITS & FEATURES ƒ Certified and serialized to meet DNV 2.7-1 and 2.7-3 Offshore Container Specifications and 2.22 Lifting Appliances Requirements. ƒ Design factor of 5:1 or higher in accordance with DNV 2.7-1 requirements. ƒ Welds exceed Charpy V impact strength of 27 Joules at -20ºC (20 ft-lb, at -4ºF) as per DNV 2.7-1. ƒ Exceed ASTM A952 specifications for lifting components. ƒ Designed to meet ASME B30.9 requirements. ƒ Links are 100% proof tested at the manufacturing facility at two times the WLL.
F
D
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
95
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80) ®
MASTER RING HERC-ALLOY 800
WORKING LOAD LIMIT: 3,500 TO 141,000 LBS. BENEFITS & FEATURES ƒ Made from alloy material ƒ Proof tested at two times WLL ƒ Durable orange powder coated finish B
A
Type and Size of Chain Sling (in.)
Working Load Limit (lbs.)
Product Code
Material Diameter A
Inside Length B
Weight (lbs.)
Single
Double
Triple
Quadruple
1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2
3,500 6,100 10,500 12,300 18,400 28,300 31,300 53,000 73,500 88,900 141,000
554611 554613 554615 554617 554619 554623 554627 554630 554635 554636 554640
0.51 0.63 0.75 0.88 1.00 1.25 1.50 1.75 2.00 2.25 2.50
2.50 3.00 4.00 4.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00
0.52 0.99 1.86 2.60 3.45 6.98 11.80 18.70 27.90 39.90 54.60
7/32 & 9/32 – 3/8 1/2 5/8 3/4 – 7/8 & 1 1-1/4 – –
– 7/32 9/32 – 3/8 1/2 – 5/8 7/8 – 1
– 7/32 9/32 – – 3/8 – 1/2 5/8 3/4 7/8 & 1
– 7/32 9/32 – – 3/8 – 1/2 5/8 3/4 7/8 & 1
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
Dimensions (in.)
Trade Size (in.)
®
GRAB LINK HERC-ALLOY 800
WORKING LOAD LIMIT: 3,500 TO 18,100 LBS. BENEFITS & FEATURES ƒ Made from alloy material ƒ Proof tested at two times the WLL ƒ Economical chain adjuster for single slings ƒ Durable orange powder coated finish
B
C
D A
Dimensions (in.)
Trade Size (in.)
Working Load Limit (lbs.)
Product Code
1/2 3/4 1 1-1/4
3,500 7,100 12,000 18,100
554320 554326 554332 554337
Diameter A 0.56 0.75 1.00 1.25
Inside Length Inside Width B C 5.50 6.06 7.63 9.25
2.50 2.75 3.50 4.38
Inside Width D 0.54 0.63 0.75 1.00
Weight (lbs.) 1.01 2.08 4.59 9.16
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
79
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80) ®
OMEGALOK CONNECTOR HERC-ALLOY OYY 800 WORKING LOAD LIMIT: 3,500 TO 18,100 LBS. BENEFITS & FEATURES ƒ Fraction and metric markings ƒ Durable orange powder coated finish ƒ 100% proof tested ƒ Fatigue rated to Grade 80 specifications ƒ For use with master link with flats (see page 77)
D E
T
G
M
L PIN
H B
Size (in.) 9/32 3/8 1/2 5/8
Product Code Working Load Limit Standard Completed Load Retainer Package (lbs.) Unit Pin Pin 3,500 7,100 12,000 18,100
12 12 12 5
644128 644138 644150 644162
595780 595781 595782 595785
602326 495821 495822 495823
Dimensions (in.) B
D
E
G
H
L
M
T
Weight (lbs.)
1.36 1.90 2.31 2.87
2.30 2.82 3.52 4.46
0.98 1.25 1.56 2.00
2.81 3.57 4.44 5.45
0.33 0.45 0.59 0.75
0.36 0.51 0.63 0.75
1.45 1.77 2.26 2.72
0.43 0.57 0.70 0.88
0.40 1.02 1.92 3.20
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS ®
HAMMERLOK HERC-ALLOY 800
®
WORKING LOAD LIMIT: 2,100 TO 72,300 LBS. BENEFITS & FEATURES ƒ Used for overhead lifting slings to connect chain branches to the master link and the hook to attachments. ƒ Constructed of drop forged alloy steel ƒ Can be used with Grade 80 chain ƒ Must be matched to chain size ƒ Do not use for chain repair or splicing ƒ Meets ASTM A952 standards.
80
Completed Unit
Load Pin Kit
Dimensions (in.)
Size (in.)
Working Load Limit (lbs.)
Product Code
Weight (lbs.)
Standard Package
Product Code
Weight (lbs.)
A
B
C
D
E
F
G
7/32 9/32 3/8 1/2 5/8 3/4 7/8 1 1-1/4
2,100 3,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
664021-2 664028-2 664038-2 664050-2 664062-2 664075-2 664089-2 664100-2 664125-2
0.12 0.26 0.59 1.42 2.35 3.67 5.98 9.47 16.61
36 36 36 24 12 12 6 – –
R664021-2 R664028-2 R664038-2 R664050-2 R664062-2 R664075-2 R664089-2 R664100-2 R664125-2
0.01 0.02 0.05 0.12 0.20 0.30 0.40 0.70 1.20
0.25 0.34 0.48 0.66 0.78 0.96 1.16 1.32 1.57
0.25 0.31 0.50 0.70 0.81 0.94 1.05 1.25 1.53
1.40 1.94 2.41 3.51 4.06 4.78 5.25 6.00 6.81
0.50 0.75 0.88 1.29 1.50 1.80 1.97 2.31 2.17
0.58 0.70 0.91 1.41 1.70 1.97 2.09 2.37 2.98
1.21 1.51 2.09 2.96 3.52 4.11 4.95 5.87 7.04
0.44 0.56 0.80 1.15 1.40 1.71 1.88 2.33 2.67
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80) ®
CLEVLOK SLING HOOK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 2,700 TO 35,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Available with and without a latch ƒ Quench and tempered alloy steel ƒ Clevlok head design ƒ 100% proof tested and fatigue rated ƒ Durable orange powder coated finish ƒ Improved forged latch (hook available with or without latch) ƒ Replacement pin and latch kit available ƒ New CE compliant hooks and latches ƒ Meets EN 1677, ASTM A953 and ASME B30.10 standards
O H
H
L
L M (MIN)
R
G
R
G
M (MIN)
P
P
I
Size (in.) 7/32 9/32 3/8 1/2 5/8 3/4
Working Load Limit Standard Package (lbs.) 2,700 4,300 8,800 15,000 22,600 35,300
10 10 10 5 5 Bulk
D
Product Code With Latch
Without Latch
657716 657718 657719 657720 657721 657722
557716 557718 557719 557720 557721 557722
Latch Kit
Dimensions (in.) D
G
H
I
L
M
O
P
R
Weight (lbs.)
3.05 3.53 4.54 5.48 6.20 7.63
5.00 5.55 6.93 8.28 9.61 11.79
0.31 0.38 0.47 0.58 0.71 0.88
0.66 0.75 1.00 1.33 1.47 1.88
0.28 0.36 0.51 0.63 0.75 0.94
0.96 0.83 1.06 1.38 1.69 2.09
1.13 1.32 1.34 1.87 2.11 2.55
0.94 1.11 1.51 1.55 1.83 2.51
3.45 3.75 4.58 5.59 6.44 7.74
1.10 1.20 2.21 4.22 6.64 11.22
Alloy Load Retaining Pin Pin
4X455321 SP595778 4X455322 595780SP 4X455325 595781 4X455328 595782 4X455329 SP595783P 4X455330 595786
495826 495825 495825 495823 495849 495824
EYE SLING HOOK DUAL RATED FOR USE WITH HA800 OR HA1000
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
D
WORKING LOAD LIMIT: 2,700 TO 72,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Available with and without latch ƒ Quench and tempered alloy steel ƒ 100% proof tested ƒ Fatigue rated ƒ Hook available with and without latch (replacement latch available) ƒ Durable orange powder coated finish
B H L
M
N
O
E
S I
P
K
D
Size (in.)
Working Load Limit (lbs.)
Standard Package
7/32 9/32 3/8 1/2 5/8 3/4 7/8* 1* 1-1/4*
2,700 4,300 8,800 15,000 22,600 35,300 34,200 47,700 72,300
10 10 10 5 5 Bulk Bulk Bulk Bulk
Product Code With Latch
Without Latch
558618 558622 558625 558628 558629 558630 558332 558333 558335
458618 458622 458625 458628 458629 458630 458732 458733 458735
G
Dimensions (in.) Latch Kit
B
4X458321 1.50 595523 1.63 595525 2.06 595528 2.63 595529 3.06 595530 3.50 595532 3.88 595533 4.31 595535 5.31
D
E
G
H
I
K
L
M
N
O
P
S
Weight (lbs.)
3.04 3.50 4.33 5.50 6.34 7.83 8.59 9.59 11.56
1.03 1.50 1.88 2.25 2.63 3.00 3.38 4.00 4.66
5.06 5.25 6.64 8.16 9.66 11.38 12.72 14.23 17.00
0.38 0.44 0.56 0.75 0.88 1.00 1.09 1.22 1.50
0.66 0.73 0.95 1.17 1.44 1.69 1.94 2.14 2.62
1.48 1.59 2.19 2.56 2.63 3.44 3.88 4.25 4.64
0.75 0.75 0.94 1.13 1.31 1.50 1.69 1.88 2.31
3.75 3.75 4.78 5.69 6.50 7.81 8.75 9.88 11.50
1.17 1.19 1.44 1.78 2.03 2.50 2.78 3.13 3.88
0.98 1.20 1.45 1.94 2.38 2.83 3.22 3.55 4.25
0.94 1.05 1.28 1.66 2.19 2.51 2.84 3.09 3.89
0.96 1.06 1.31 1.63 1.75 2.19 2.38 2.88 3.41
0.8 1.10 1.90 4.30 7.30 12.50 18.10 22.60 47.00
* Herc-Alloy 800® only
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
81
RIGGING HARDWARE
RIGGING HOOK WORKING LOAD LIMIT: 3/4 TO 15 TONS BENEFITS & FEATURES ƒ Load rating marked on each hook body ƒ Design factor 5:1 ƒ Pre-drilled latch tab allows addition of latch ƒ Carbon hooks have a clear protective coating to resist rust and for cleaner handling ƒ Alloy hooks have orange powder coated finish
Standard Package
10 10 5 5 5 5 – – –
B
L R
T G
without Latch
with Latch
Zinc Plated Latch Kit (optional) Product Code
M6402A M6403A M6404A M6405A M6407A M6409A M6411A M6415A M6422A
M6502A M6503A M6504A M6505A M6507A M6509A M6511A M6515A M6522A
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309 4X1311 4X1315 4X1322
Clear Finish
Painted Orange
3/4 1 1-1/2 2 3 5 7-1/2 10 15
without Latch
with Latch
M6402C M6403C M6404C M6405C M6407C M6409C M6411C M6415C M6422C
M6502C M6503C M6504C M6505C M6507C M6509C M6511C M6515C M6522C
WLL* (tons) 1 1-1/2 2 3 5 7 11 15 22
K D
H
Alloy
Product Code
J O K
Carbon
WLL* (tons)
A
C
Product Code
Dimensions (in.)
A
B
C
D
G
H
J
K
L
O
R
T
1.50 1.75 2.13 2.50 3.08 3.88 4.69 5.34 6.63
0.75 0.88 1.10 1.25 1.56 1.98 2.44 2.84 3.50
0.38 0.44 0.50 0.64 0.77 0.94 1.13 1.25 1.56
3.12 3.37 3.80 4.20 5.11 6.24 7.89 8.53 10.30
0.87 0.94 1.06 1.26 1.44 1.82 2.25 2.75 3.15
1.01 1.11 1.21 1.43 1.63 2.01 2.63 3.10 3.62
0.93 0.97 1.02 1.19 1.50 1.78 2.38 2.50 3.30
0.63 0.71 0.74 0.94 1.38 1.68 1.88 2.03 2.60
4.37 5.04 5.65 6.55 7.97 10.07 12.41 14.05 17.53
0.93 0.97 1.02 1.16 1.41 1.69 2.19 2.30 3.12
3.13 3.66 4.09 4.67 5.78 7.31 9.03 10.21 12.81
0.87 0.97 1.03 1.16 1.53 1.94 2.52 2.54 2.73
Latch Kit
Weight (lbs.)
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309 4X1311 4X1315 4X1322
0.66 1.12 1.46 2.42 4.10 8.16 15.60 21.58 39.89
* Working Load Limits in Metric Tons. Note: Other finishes are available as special orders.
SWIVEL RIGGING HOOK RIGGING HARDWARE
WORKING LOAD LIMIT: 1 TO 22 TONS BENEFITS & FEATURES ƒ Design factor 5:1 ƒ Pre-drilled for latches ƒ Hooks furnished with or without latches ƒ Powder coated orange ƒ Hooks are heat treated, quenched and tempered
A C S
B
R
L
O
I
T G H D
Standard Package 10 10 10 10 10 Bulk Bulk Bulk Bulk
WLL* (tons) 1 1-1/2 2 3 5 7 11 15 22
Alloy Product Code without Latch
with Latch
Zinc Plated Latch Kit (optional) Product Code
M3402A M3403A M3404A M3405A M3407A M3409A M3411A M3415A M3422A
M3502A M3503A M3504A M3505A M3507A M3509A M3511A M3515A M3522A
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309 4X1311 4X1315 4X1322
Dimensions (in.)) A
B
C
D
G
H
I
2.00 2.50 3.00 3.00 3.50 4.75 5.50 6.00 7.75
1.11 1.38 1.65 1.65 1.77 2.39 2.55 2.47 3.82
1.31 1.50 1.75 1.75 2.00 2.75 3.25 3.50 4.75
3.06 3.33 3.67 4.20 5.11 6.24 7.69 8.37 10.19
0.87 0.94 1.06 1.27 1.44 1.82 2.25 2.59 3.00
1.05 1.11 1.21 1.43 1.63 2.01 2.63 2.94 3.50
0.63 0.71 0.88 0.94 1.31 1.68 1.88 2.19 2.69
L
R
5.83 4.63 6.83 5.44 7.76 6.25 8.40 6.49 9.76 7.53 12.42 9.67 14.89 12.06 15.79 11.95 21.18 16.68
S
T
O
Latch Kit
Weight (lbs.)
0.38 0.50 0.63 0.63 0.75 1.00 1.13 1.25 1.50
0.87 0.97 1.03 1.16 1.53 1.94 2.46 2.62 2.74
0.93 0.97 1.06 1.16 1.41 1.69 2.22 2.23 3.05
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309 4X1311 4X1315 4X1322
1.05 1.56 2.50 3.20 5.36 10.56 19.00 26.75 51.80
* Working Load Limits in Metric Tons
90
C H A I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80) ®
CLEVLOK GRAB HOOK WITHOUT CRADLE HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 3,500 TO 18,100 LBS. BENEFITS & FEATURES ƒ Quench and tempered alloy steel ƒ Fatigue rated ƒ Built without lugs to avoid catching when slipping into tight clearance ƒ Durable orange powder coated finish ƒ Replacement pin available
B
H
L
E M
G
K P T
D
Size (in.)
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
9/32 3/8 1/2 5/8
Product Code Working Load Limit Standard Completed Load Retainer Package (lbs.) Unit Pin Pin 3,500 7,100 12,000 18,100
10 10 5 5
659232 659235 659238 659239
595780 595781 595782 595783
602326 495821 495822 495823
Dimensions (in.) B
D
E
G
H
K
L
M
P
T
Weight (lbs.)
1.36 1.90 2.31 2.87
1.91 2.78 3.62 4.41
0.36 0.47 0.59 0.75
3.70 4.81 6.35 7.74
0.33 0.45 0.59 0.75
1.04 1.49 1.98 2.39
0.36 0.51 0.63 0.75
2.29 2.87 3.78 4.82
0.76 1.03 1.51 1.80
0.81 1.06 1.38 1.69
0.6 1.3 2.5 4.4
Note: If used as a choker, working load limit should be reduced by 20%.
®
CLEVLOK CRADLE GRAB HOOK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 2,700 TO 28,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Unique cradle grab design ƒ Quench and tempered alloy steel ƒ Fatigue rated ƒ Durable orange powder coated finish ƒ Replacement pin available
J
H L G M
R
P K
D
Dimensions (in.)
Size (in.)
Working Load Limit (lbs.)
Product Code
Standard Package Quantity
D
G
H
J
K
L
M
P
R
Weight (lbs.)
7/32 9/32 3/8 1/2 5/8 3/4*
2,700 4,300 8,800 15,000 22,600 28,300
659718 659722 659725 659728 659729 659430
10 10 10 5 5 Bulk
1.62 2.18 2.72 3.65 4.50 5.23
3.21 3.39 4.33 5.27 6.54 9.08
0.31 0.38 0.47 0.65 0.77 0.88
0.75 0.82 1.18 1.39 1.55 2.05
0.94 0.97 1.29 2.01 2.42 2.88
0.28 0.36 0.51 0.63 0.75 0.91
0.31 0.38 0.74 0.60 0.77 0.88
0.62 0.82 1.03 1.19 1.41 1.87
1.98 1.86 2.47 3.04 3.76 5.50
0.50 0.63 1.30 2.10 4.20 10.24
* 3/4" is Herc-Alloy 800® only. Hook shape/style differs from photo and dimension drawing shown. Note: If used as a choker, working load limit should be reduced by 20%.
82
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80)
EYE CRADLE GRAB HOOK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 3,200 TO 72,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Unique cradle grab design ƒ Quench and tempered alloy steel ƒ 100% proof tested ƒ Fatigue rated ƒ Durable orange powder coated finish
B L
H
M E
G
K P
Dimensions (in.)
Size (in.)
Working Load Limit (lbs.)
Standard Package
Product Code
B
D
E
G
H
I
K
L
M
P
Weight (lbs.)
7/32 9/32 3/8 1/2 5/8 3/4 7/8* 1* 1-1/4*
3,200 4,300 8,800 15,000 22,600 35,300 34,200 47,700 72,300
10 10 10 5 5 Bulk Bulk Bulk Bulk
559724 559725 559737 559750 559762 559775 559387 559100 559124
1.20 1.40 1.78 2.28 2.75 3.50 3.75 4.31 5.38
1.68 1.93 2.86 3.63 4.53 5.23 5.69 7.00 8.50
0.31 0.36 0.47 0.59 0.75 0.91 1.00 1.19 1.53
3.22 3.72 4.81 6.36 7.62 9.54 9.63 12.44 15.56
0.33 0.39 0.52 0.63 0.75 1.00 1.00 1.22 1.56
0.92 1.07 1.65 1.81 2.13 2.88 3.00 3.88 2.50
0.99 1.13 1.49 2.15 2.65 3.52 3.75 4.31 5.50
0.55 0.63 0.78 1.06 1.22 1.52 1.75 1.88 2.25
2.20 2.57 3.27 4.23 5.06 6.70 6.50 8.09 10.50
0.69 0.76 1.02 1.53 1.80 1.85 2.12 3.12 3.50
0.35 0.55 1.06 2.00 5.40 9.00 10.40 20.90 40.00
* Herc-Alloy 800® only Note: If used as a choker, working load limit should be reduced by 20%.
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
I
D
EYE FOUNDRY HOOK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 4,300 TO 72,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Throat opening up to 6" ƒ Quench and tempered alloy steel ƒ Fatigue rated ƒ Durable orange powder coated finish
H
B L
G (REF)
N
M I
O
R (SPHER.)
E K
D (REF)
Size (in.) 9/32 3/8 1/2 5/8 3/4 7/8* 1* 1-1/4*
Working Load Limit Standard Package (lbs.) 4,300 8,800 15,000 22,600 35,300 34,200 47,700 72,300
5 5 5 5 Bulk Bulk Bulk Bulk
Dimensions (in.)
Product Code
B
D
E
G
H
I
K
L
M
N
O
R
Weight (lbs.)
474798 474799 474800 474801 474802 474503 474504 474505
1.56 2.00 2.50 3.00 3.50 4.00 4.50 5.13
4.73 5.72 6.75 7.81 9.10 10.09 11.55 12.87
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00
6.45 7.88 9.38 10.97 12.81 14.23 16.17 18.03
0.47 0.63 0.75 0.88 1.00 1.13 1.29 1.38
1.00 1.27 1.50 1.81 2.20 2.25 2.63 3.17
1.56 1.88 2.22 2.63 3.00 3.38 3.75 4.25
0.63 0.80 1.00 1.25 1.50 1.70 2.13 2.33
4.75 5.77 6.88 8.06 9.25 10.38 11.56 12.88
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00
1.23 1.50 1.75 2.03 2.56 2.78 3.45 3.81
0.25 0.31 0.38 0.44 0.50 0.56 0.62 0.75
2.4 4.5 7.1 11.6 20.0 26.0 36.8 58.4
* Herc-Alloy 800® only
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
83
RIGGING HARDWARE
®
SORTING HOOK HERC-ALLOY 800 WORKING LOAD LIMIT: 7-1/2 TONS BENEFITS & FEATURES ƒ 5:1 design factor ƒ Quench and tempered alloy steel ƒ Long tapered point designed for easy grab in rings, pear links, eye bolts or lifting holes ƒ Durable orange powder coated finish ƒ Do not load last 1" of the tip
A
M
C
B E D
I H
G F
Working Load Limit (lbs.)
With Handle
Without Handle
Dimensions (in.)
At Tip (ton)
At bottom of Hook (ton)
Product Code
Weight (lbs.)
Product Code
Weight (lbs.)
A
B
C
D
E
F
G
H
I
M
1
7-1/2
M129H
7.0
M129
6.8
3
1.44
0.78
7.34
3.75
1.28
1.25
3.93
10.09
6.58
®
SHANK HOOK HERC-ALLOY 800 WORKING LOAD LIMIT: 1 TO 7 TONS
RIGGING HARDWARE
BENEFITS & FEATURES ƒ Heat treated alloy steel provides strength without bulk or weight ƒ Pre-drilled boss allows for latch ƒ Shank hooks are supplied unthreaded, but can be supplied threaded as a special order item ƒ Shank hooks made from other material (bronze, stainless steel, etc.) available upon request
Z
X
H Y O
Z
J w/o Latch L R F
K
P G
T
K
D
Alloy Shank Hook Latch Max Kit Shank Latch Working Product Weight Hole (lbs.) Product Diameter Load Limit (in.) Code Code (in.) (ton) 1 1-1/2 2 3 5 7
M1302A M1303A M1304A M1305A M1307A M1309A
0.65 0.80 1.47 1.85 4.04 7.25
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309
0.72 0.79 0.86 1.11 1.30 1.56
0.14 0.19 0.18 0.18 0.20 0.20
Dimensions (in.) D
F
G
H
J
3.09 3.37 3.75 4.23 5.16 6.24
1.25 1.38 1.50 1.63 2.00 2.50
0.87 0.94 1.04 1.25 1.44 1.82
1.01 1.11 1.21 1.43 1.63 2.01
0.91 0.97 1.06 1.17 1.48 1.78
K
L
0.63 5.44 0.71 5.92 0.88 6.45 0.94 7.42 1.38 8.80 1.68 10.72
O
P
R
X
Y
Z
0.88 0.91 1.00 1.16 1.41 1.69
2.12 2.27 2.58 2.84 3.52 4.59
2.35 2.59 2.75 3.16 3.85 4.70
0.66 0.73 0.79 0.96 1.24 1.49
2.22 2.39 2.66 3.01 3.52 4.02
0.69 0.80 1.00 1.03 1.27 1.56
The following should be observed: V Shanks are not intended for internal threading or swaging. V To obtain maximum strength threads should be class 1 or 2. V Thread engagement in nut or object must be a minimum of 1-1/2 times the thread diameter. Insufficient thread engagement can result in loss of load.
88
C H A I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
RIGGING HARDWARE
®
PLATE HOOK HERC-ALLOY 800
WORKING LOAD LIMIT: 3,600 TO 11,400 LBS. BENEFITS & FEATURES ƒ Made from alloy material ƒ Designed to handle plate steel ƒ Durable orange powder coated finish ƒ Available as components or attached to certified slings
T L R D M
C
R
A
B
N
R W
Size (in.)
Working Product Load Limit Code (lbs.)
9/32 3/8 1/2
462528 462537 462550
3,600 7,050 11,400
Dimensions (in.) A
B
C
D
L
M
N
T
W
R
2.00 2.63 3.50
1.75 2.97 4.00
2.50 4.31 4.38
0.94 1.24 1.50
1.00 1.13 1.50
3.48 6.53 6.98
0.13 0.19 0.28
0.63 0.75 1.00
2.50 2.75 3.50
0.31 0.50 0.50
Weight (lbs.) 2.80 5.70 13.00
Other sizes available
NEVER USE PLATE HOOKS ON A QUAD SLINGS. To lift a plate with a quad sling, a spreader or beam is required and hooks would go on the end of double chain slings that would be attached to each end of the beam.
® ® HERC-ALLOY 800 RIGGING HARDWARE
ALLOY “S” HOOK HERC-ALLOY 800 WORKING LOAD LIMIT: 210 TO 6,250 LBS. BENEFITS & FEATURES ƒ Made from alloy material ƒ Proof tested at two times WLL ƒ Durable orange powder coated finish ƒ WLL embossed on hooks ƒ Custom sizes available upon request ƒ Serialized upon request
D C
A C
B
Size (in.)
Working Load Limit (lbs.)
Product Code
9/32 3/8 1/2 5/8 3/4 7/8 1 1-5/32 1-1/4 1-3/8 1-1/2
210 410 870 1,120 1,730 2,370 2,920 3,150 4,450 6,100 6,250
562228 562237 562250 562262 562275 562287 562300 562310 562325 562337 562350
Dimensions (in.) A
B
C
D
Weight (lbs.)
0.28 0.38 0.56 0.63 0.75 0.88 1.00 1.13 1.25 1.38 1.50
4.50 6.00 7.50 9.00 10.50 12.00 13.00 15.00 16.00 17.00 18.00
1.13 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00
1.13 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00
0.15 0.35 1.04 1.56 2.60 4.20 6.00 9.30 11.70 15.40 19.50
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
89
RIGGING HARDWARE
REPLACEMENT HOOK WITH LATCH WORKING LOAD LIMIT: 1 TON D
BENEFITS & FEATURES ƒ Easy installation ƒ Bolt, nut, and cotter pin provides safe and secure attaching points ƒ Self colored finish ƒ Easy installation
E
B
A
C
Working Load Limit (ton)
Product Code
A
B
C
D
E
Weight (lbs.)
1
M134
7.56
5.63
1.13
0.50
0.44
2.56
Dimensions (in.)
CLB CONTAINER LIFTING LUGS WORKING LOAD LIMIT: 88,100 LBS. (PER SET OF 4)
Supplied in sets of 4, CLB Lifting Lugs serve as flexible lashing points for the transportation of containers.
RIGGING HARDWARE
BENEFITS & FEATURES ƒ Spring-loaded bolt to prevent accidental release ƒ Mounted horizontally at the side of the container in either upper or lower holes ƒ Easy installation and removal – simply insert and turn to install ƒ Designed to eliminate the dangerous use of standard hooks
ƒ Lugs cannot drop out when slings become slack ƒ Lugs can be used for left hand or right hand turns ƒ For maximum capacity, use a lifting beam in conjunction with CLB lifting lugs
G
50T Vertical
D
40T 20
C E
B
36º 32T 50º
F
A
92
Dimensions (in.)
Product Code
Working Load Limit (lbs. per set of 4)
A
B
C
D
E
F
G
Weight (lbs.)
CLB40
88,100
5.984
7.126
1.772
1.457
2.874
2.953
1.575
39.7
REDUCTION OF WORKING LOAD LIMIT Angle of lift must be specified when ordering CLB lifting lugs
C H A I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
HERC-ALLOY 800 CHAIN WORKING LOAD LIMIT: 2,100 TO 72,300 LBS. BENEFITS & FEATURES ƒ A higher strength heat treated alloy steel chain primarily used as a sling component for overhead lifting ƒ Can be used in rigging and tie down applications where a lighter weight, higher strength chain is desirable ƒ Recommended for overhead lifting by NACM, ASME, and OSHA B
C 1000
A
Nominal Chain Dimensions (in.)
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
Chain Size (in.)
Working Load Limit (lbs.)
7/32 9/32 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4
2,100 3,500 4,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
Per Foot
Per Drum
Material Diameter A
Inside Length B
Inside Width C
Product Code
Weight (lbs./ft.)
Approximate Number of Links (per ft.)
Product Code
Length (ft.)
Weight (lbs.)
0.22 0.28 0.32 0.39 0.51 0.63 0.79 0.88 1.00 1.25
0.68 0.88 1.02 1.25 1.44 1.78 2.23 2.25 3.07 3.92
0.31 0.40 0.46 0.57 0.73 0.86 1.07 1.14 1.49 1.74
607020 607028 607031 607037 607050 607062 607075 607087 607101 607128
0.44 0.73 0.91 1.44 2.55 3.82 5.95 7.76 9.41 14.20
17.8 13.6 11.8 9.6 8.3 6.8 5.4 5.3 3.9 3.1
677010 677011 – 677013 677015 677016 677017 677018 677019 677070
800 500 – 500 300 200 100 100 100 90
354 365 – 719 765 765 595 776 941 1,278
INSPECTION, CARE & USE HOW TO SELECT AND ORDER THE PROPER CHAIN SLING 1. Determine the weight and configuration of the load(s) to be lifted. 2. Determine the type of chain sling required, according to weight and configuration. (See page 31 for standard sling configurations.) 3. Determine the size of the body chain according to the working load limits. Be sure to take into consideration the effect of the required angle. The working load limit is the maximum load in pounds which should be applied in direct tension to a straight length of chain. Note: Working load limit can be affected by angles of loading, type of hitch used, environmental conditions such as hot and cold temperatures, and D/d ratio. 4. Determine the reach required to give the desired angle. The reach is measured from the upper bearing surface of the master link to the bearing surface of the lower attachment. If chain slings are to be used in pairs and are to be matched for reach, please indicate when ordering. 5. Know share of load on pick points and location of center of gravity. See pages 26 through 32 for more information, or visit us at www.cmworks.com
74
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80) ®
HERC-ALLOY 800 CHAIN SLINGS
SINGLE ENDLESS
DOUBLE DOUBLE (2 LEGS)
DOUBLE ENDLESS
TRIPLE (3 LEGS)
SINGLE BASKET
MAGNET MAGNET SLING
QUADRUPLE (4 LEGS)
SINGLE ADJUSTABLE
DOUBLE BASKET
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
SINGLE SIN NGLE LEG LEG (VERTICAL)
DOUBLE ADJUSTABLE
Adjusters on slings allow for easy and safe take up of chain when applications require shorter leg lengths or when lifting objects of abnormal sizes. There are two styles of adjusters: Style A and Style B. Style A is commonly used for shorter reach slings and consists of a hook attached to the link. Style B has 12" of chain in between link and hook gives you more flexibility on longer slings. Note: Adjusters are also available on single, double, triple and quad slings. Working Load Limits for Sling Types Show Above Chain Size (in.)
7/32 9/32 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4
Single (1 leg)
Single Choker
90º (lbs.)
90º (lbs.)
60º (lbs.)
45º (lbs.)
30º (lbs.)
60º (lbs.)
45º (lbs.)
30º (lbs.)
60º (lbs.)
45º (lbs.)
2,100 3,500 4,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
1,700 2,800 3,600 5,700 9,600 14,500 22,600 27,400 38,200 57,800
3,600 6,100 7,800 12,300 20,800 31,300 49,000 59,200 82,600 125,200
3,000 4,900 6,400 10,000 17,000 25,600 40,000 48,400 67,400 102,200
2,100 3,500 4,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
5,500 9,100 11,700 18,400 31,200 47,000 73,500 88,900 123,900 187,800
4,400 7,400 9,500 15,100 25,500 38,400 60,000 72,500 101,200 153,400
3,200 5,200 6,800 10,600 18,000 27,100 42,400 51,300 71,500 108,400
5,500 9,100 11,700 18,400 31,200 47,000 73,500 88,900 123,900 187,800
4,400 7,400 9,500 15,100 25,500 38,400 60,000 72,500 101,200 153,400
Double (2 legs)
Triple (3 legs)
Single Basket
Double Basket
Single Endless
Double Endless
30º (lbs.)
60º (lbs.)
60º (lbs.)
90º (lbs.)
60º (lbs.)
3,200 5,200 6,800 10,600 18,000 27,100 42,400 51,300 71,500 108,400
3,600 6,100 7,800 12,300 20,800 31,300 49,000 59,200 82,600 125,200
5,500 9,100 11,700 18,400 31,200 47,000 73,500 88,900 123,900 187,800
2,100 3,500 4,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
3,600 6,100 7,800 12,300 20,800 31,300 49,000 59,200 82,600 125,200
Quad (4 legs)
American Society of Mechanical Engineers ASME B30.9, the National Association of Chain Manufacturers (NACM) and the Occupation Safety & Health istration (OSHA) recommend only the use of alloy steel chain for overhead lifting, i.e. sling chain. Slings may be constructed by the using Herc-Alloy® chain, Herc-Alloy 1000 or Herc-Alloy 800 chain and attachments.
For more information on standard sling configurations, see page 31 or visit us online at www.cmworks.com
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
75
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80)
MASTER LINK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 3,600 TO 187,800 LBS. BENEFITS & FEATURES ƒ ƒ ƒ ƒ
Accepts both Herc-Alloy® 1000 & 800 chain and components Durable orange powder coated finish May be used for mechanical and welded sling assemblies 100% proof tested
B
A
C
Trade Size (in.)
Working Catalog Load Limit Number (lbs.)
Product Code
Nominal Dimensions (in.) Material Diameter A
Inside Length B
Inside Width C
Weight (lbs.)
Type and Size of Grade 80 Chain Sling (in.) Single
Double
Standard Sizes (DUAL RATED THROUGH 1-3/4" SIZE ONLY)
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
3/8 1/2 3/4 1 1-1/4 1-1/2 1-3/4 2* 2-1/4* 2-3/4*
5,400 8,600 17,600 30,000 45,200 70,600 105,900 88,900 125,200 187,800
HA40 HA50 HA75 HA100 HA125 HA150 HA175 HA200 HA225 HA275
555231 555232 555235 555238 555240 555243 555246 554949 554951 554957
0.41 0.56 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.75
3.00 5.00 5.50 7.00 8.75 10.50 12.00 14.00 16.00 16.00
1.50 2.50 2.75 3.50 4.38 5.25 6.00 7.00 8.00 9.00
0.33 1.02 2.08 4.59 9.31 15.60 24.40 38.00 55.00 84.84
7/32 & 9/32 3/8 1/2 5/8 & 3/4 7/8 1 1-1/4 1-1/4 – –
7/32 9/32 3/8 1/2 5/8 3/4 & 7/8 1 1 1-1/4 –
554969 554942 554944 554970 554945 554952
1.00 1.25 1.50 1.50 1.75 2.00
8.00 12.00 14.00 12.00 14.00 16.00
4.00 6.00 7.00 6.00 7.00 8.00
5.25 12.08 20.16 17.60 27.92 43.00
N/A
N/A
Can be used with included angles up to 120°
120º
Special Sizes (NOT DUAL RATED) 1 1-1/4 1-1/2 1-1/2 1-3/4 2
18,200 22,800 36,700 42,900 57,100 77,800
N/A
NOTE: Standard sizes dual rated through 1-3/4" only. Special sizes not dual rated.
FORGED MASTER LINK GRADE 80 WORKING LOAD LIMIT: 5,100 TO 20,400 LBS. D
BENEFITS & FEATURES ƒ ƒ ƒ ƒ ƒ
Quench and tempered alloy steel Fatigue rated to Grade 80 specifications 100% proof tested Raised markings for better identification Durable orange powder coated finish
Can be used with included angles up to 120°
B
120º
C
76
A
Nominal Dimensions (in.)
Trade Size (in.)
Working Load Limit (lbs.)
Product Code
Material Diameter A
Inside Length B
Inside Width C
Weight (lbs.)
1/2 5/8 3/4 1
5,100 7,700 10,600 20,400
M50P M62P M75P M100P
0.50 0.63 0.75 1.00
5.00 6.00 6.00 8.00
2.50 3.00 3.00 4.00
0.90 1.75 2.35 6.00
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80)
MASTER LINK WITH & WITHOUT FLATS HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 4,200 TO 327,800 LBS. BENEFITS & FEATURES
Flat
ƒ Designed to accept HA800 chain, wire rope and synthetic attachments ƒ Use with mechanical and welded assemblies ƒ Sizes up to 1-1/4" available with flats to accommodate Omega link ƒ 100% proof tested ƒ Extra wide body makes these links ideal for wire rope applications and use with Omegaloks. Master link with flat allows for easy installation of these attachments.
Can be used with included angles up to 120°
With Chain
With Wire Rope & Synthetics
7/16
4,200
3,360
1/2
5,750
4,600
5/8
9,000
7,200
3/4
14,200
11,360
7/8
17,300
13,840
1
26,500
21,200
1-1/4
37,400
29,920
1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4
53,000 72,150 94,200 119,200 147,150 178,050
42,400 57,720 75,360 95,360 117,720 142,440
Nominal Dimensions (in.) Product Code
Material Diameter A
Inside Length B
Inside Width C
0.44
4.13
2.29
0.56
4.84
2.69
0.63
5.29
2.98
0.75
6.61
3.72
0.88
7.35
4.14
ML040 ML040NF ML050 ML050NF ML063 ML063NF ML075 ML075NF ML087 ML087NF ML100 ML100NF ML125 ML125NF ML150 ML175 ML200 ML225 ML250 ML275
1.00
7.53
Flat Dimensions (in.)
4.30
1.25
9.26
5.29
1.50 1.75 2.00 2.25 2.50 2.75
11.03 12.86 14.70 16.54 18.38 20.21
6.30 7.35 8.40 9.45 10.50 11.55
Width
Thickness
0.94 – 0.94 – 1.22 – 1.41 – 1.56 – 1.56 – 1.56 – – – – – – –
0.28 – 0.28 – 2.81 – 0.40 – 0.44 0.53 0.68 – – – – – – –
Type and Size of Chain Sling (in.) Weight (lbs.)
Single
Double
0.50
7/32 & 9/32
7/32
1.02
–
7/32
1.34
3/8
9/32
2.36
1/2
3/8
3.60
–
–
5.20
5/8
1/2
9.60
3/4 & 7/8
5/8
16.20 25.10 41.00 58.00 74.90 99.80
1 – 1-1/4 – – –
3/4 7/8 1 – 1-1/4 –
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
Working Load Limit (lbs.)
A
C
120º
Trade Size (in.)
B
NOTE: *Master link with flats are available through 1-1/4" only Part numbers with"NF" are for master links WITHOUT flats
FLAT BOTTOM MASTER LINK GRADE 80 WORKING LOAD LIMIT: 73,500 TO 187,800 LBS. C
BENEFITS & FEATURES ƒ ƒ ƒ ƒ
Designed to accept HA800 chain and components Made from alloy steel Extra wide width allows for larger hook usage 100% proof tested
Chain Size (in.) 5/8 & 3/4 7/8 & 1 1 & 1/4
Trade Size Working Load Limit (in.) (lbs.) 1-3/4 2 2-1/2
73,500 123,900 187,800
Product Code 554966 554950 554965
B
A
Nominal Dimensions (in.) Material Diameter A
Inside Length B
Inside Width C
1.75 2.00 2.50
8.00 8.98 11.92
5.000 5.000 6.500
Weight (lbs.) 18.96 28.04 54.73
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
77
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80)
SUB-ASSEMBLY DUAL RATED FOR USE WITH HA800 800 & HA1000 WORKING LOAD LIMIT: 7,000 TO 187,800 LBS. C
BENEFITS & FEATURES
A
ƒ Accepts both Herc-Alloy 1000 ƒ Designed for triple and quad & 800 chain and components branch Herc-Alloy® chain slings ƒ Durable orange powder ƒ Consists of an oblong master coated finish link and two welded master coupling links ƒ May be used for mechanical or welded sling assemblies ƒ 100% proof tested
B
120º E
Can be used with included angles up to 120° F
D
Trade Size (in.)
ensions (in.) Siz of Chain Sling (in.) Master Link Nominal Dimensions (in.) Intermediate Link Nominal Dimensions Type & Size Working Catalog Load Limit Product Weight Material Inside Inside Material Inside Inside Number at 60º Code (lbs.) Diameter Length Width Diameter Length Width Triple Quad (lbs.) A B C D E F
1/2 3/4 1 1-1/4 1-1/2 1-3/4 2* 2-1/4* 2-3/4*
SA50 SA75 SA100 SA125 SA150 SA175 HA200-SA HA225-SA HA275-SA
7,000 11,200 22,900 39,000 58,700 91,700 88,900 123,900 187,800
555274 555275 555276 555277 555278 555279 554980 554981 554983
0.56 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.75
5.00 5.50 7.00 8.75 10.50 12.00 14.00 16.00 16.00
2.50 2.75 3.50 4.38 5.25 6.00 7.00 8.00 9.00
0.44 0.47 0.78 0.91 1.13 1.50 1.53 1.78 2.00
1.75 1.56 2.63 3.13 4.00 5.25 5.25 6.00 7.00
1.06 0.88 1.50 1.75 2.25 2.75 2.75 3.00 3.50
1.35 2.64 7.25 13.51 24.28 44.58 57.34 81.48 126.66
7/32 9/32 3/8 1/2 5/8 3/4 & 7/8 7/8 1 1-1/4
7/32 9/32 3/8 1/2 5/8 3/4 & 7/8 7/8 1 1-1/4
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
* Grade 80 only
WIDE BODY SUB-ASSEMBLY WITH FLATS HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 4,600 TO 178,050 LBS. BENEFITS & FEATURES ƒ Extra wide body is ideal for wire rope applications ƒ Sizes up to 1-1/4" intermediate links available with flats to accommodate Omega links
C A
Can be used with included angles up to 120°
E
F
Trade Size (in.) 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4
Working Load Limit (lbs.) With Chain 5,750 9,000 14,000 17,300 26,500 37,400 53,000 72,150 94,200 119,200 147,150 178,050
Complete Assembly With Wire Product Code Rope & Synthetic 4,600 7,200 11,200 13,840 21,200 29,920 42,400 57,720 75,360 95,360 117,720 142,400
SA050 SA063 SA075 SA087 SA100 SA125 SA150 SA175 SA200 SA225 SA250 SA275
120º
B
Flat
ƒ Designed to accept Herc-Alloy 800® chain, wire rope and synthetic attachments ƒ Durable orange powder coated finish ƒ 100% proof tested ƒ May be used for mechanical and welded sling assemblies
Master Link Nominal Dimensions (in.) Product Code
Material Diameter A
Inside Length B
Inside Width C
ML050 ML063 ML075 ML087 ML100 ML125 ML150 ML175 ML200 ML225 ML250 ML275
0.56 0.63 0.75 0.88 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75
4.84 5.29 6.61 7.35 7.53 9.26 11.03 12.86 14.70 16.54 18.38 20.21
2.69 2.98 3.72 4.14 4.30 5.29 6.30 7.35 8.40 9.45 10.50 11.55
D
Intermediate Link Nominal Dimensions (in.) Product Code
Material Diameter D
Inside Length E
Inside Width F
ML040 ML050 ML063 ML063 ML075 ML100 ML100 ML125 ML150 ML175 ML200 ML200
0.44 0.56 0.63 0.63 0.75 1.00 1.00 1.25 1.50 1.75 2.00 2.00
4.13 4.84 5.29 5.29 6.61 7.53 7.53 9.26 11.03 12.86 14.70 14.70
2.29 2.69 2.98 2.98 3.72 4.30 4.30 5.29 6.30 7.35 8.40 8.40
Weight (lbs.)
1.8 2.9 5.5 6.3 10.2 20.0 26.6 44.3 73.4 108.2 156.9 181.0
Type and Size of Chain Sling (in.) Triple
Quad
– 7/32 9/32 – 3/8 1/2 – 5/8 3/4 7/8 1 –
– 7/32 9/32 – 3/8 1/2 – 5/8 3/4 7/8 1 –
NOTE: Master link with flats are available through 1-1/4" only
78
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
RIGGING HARDWARE
MASTER LINK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 3,600 TO 187,800 LBS. BENEFITS & FEATURES ƒ ƒ ƒ ƒ
Accepts both Herc-Alloy® 1000 & 800 chain and components Durable orange powder coated finish May be used for mechanical and welded sling assemblies 100% proof tested
B
C
Trade Size (in.)
Working Catalog Load Limit Number (lbs.)
Product Code
Nominal Dimensions (in.) Material Diameter A
Inside Length B
Inside Width C
Weight (lbs.)
A
Type and Size of Grade 80 Chain Sling (in.) Single
Double
Standard Sizes (DUAL RATED THROUGH 1-3/4" SIZE ONLY) 3/8 1/2 3/4 1 1-1/4 1-1/2 1-3/4 2* 2-1/4* 2-3/4*
5,400 8,600 17,600 30,000 45,200 70,600 105,900 88,900 125,200 187,800
HA40 HA50 HA75 HA100 HA125 HA150 HA175 HA200 HA225 HA275
555231 555232 555235 555238 555240 555243 555246 554949 554951 554957
0.41 0.56 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.75
3.00 5.00 5.50 7.00 8.75 10.50 12.00 14.00 16.00 16.00
1.50 2.50 2.75 3.50 4.38 5.25 6.00 7.00 8.00 9.00
0.33 1.02 2.08 4.59 9.31 15.60 24.40 38.00 55.00 84.84
7/32 & 9/32 3/8 1/2 5/8 & 3/4 7/8 1 1-1/4 1-1/4 – –
7/32 9/32 3/8 1/2 5/8 3/4 & 7/8 1 1 1-1/4 –
554969 554942 554944 554970 554945 554952
1.00 1.25 1.50 1.50 1.75 2.00
8.00 12.00 14.00 12.00 14.00 16.00
4.00 6.00 7.00 6.00 7.00 8.00
5.25 12.08 20.16 17.60 27.92 43.00
N/A
N/A
Can be used with included angles up to 120°
120º
1 1-1/4 1-1/2 1-1/2 1-3/4 2
18,200 22,800 36,700 42,900 57,100 77,800
N/A
® HERC-ALLOY 800 RIGGING HARDWARE
Special Sizes (NOT DUAL RATED)
NOTE: Standard sizes dual rated through 1-3/4" only. Special sizes not dual rated.
FORGED MASTER LINK GRADE 80 WORKING LOAD LIMIT: 5,100 TO 20,400 LBS. D
BENEFITS & FEATURES ƒ ƒ ƒ ƒ ƒ
Quench and tempered alloy steel Fatigue rated to Grade 80 specifications 100% proof tested Raised markings for better identification Durable orange powder coated finish
Can be used with included angles up to 120°
B
120º
C
A
Nominal Dimensions (in.)
Trade Size (in.)
Working Load Limit (lbs.)
Product Code
Material Diameter A
Inside Length B
Inside Width C
Weight (lbs.)
1/2 5/8 3/4 1
5,100 7,700 10,600 20,400
M50P M62P M75P M100P
0.50 0.63 0.75 1.00
5.00 6.00 6.00 8.00
2.50 3.00 3.00 4.00
0.90 1.75 2.35 6.00
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
93
RIGGING HARDWARE
MASTER LINK WITH & WITHOUT FLATS HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 3,360 TO 178,050 LBS. BENEFITS & FEATURES
Flat
ƒ Designed to accept HA800 chain, wire rope and synthetic attachments ƒ Use with mechanical and welded assemblies ƒ Sizes up to 1-1/4" available with flats to accommodate Omega link ƒ 100% proof tested ƒ Extra wide body makes these links ideal for wire rope applications and use with Omegaloks. Master link with flat allows for easy installation of these attachments.
B
Can be used with included angles up to 120°
A
C
120º
Working Load Limit (lbs.) Trade Size (in.)
With Chain
With Wire Rope & Synthetics
7/16
4,200
3,360
1/2
5,750
4,600
5/8
9,000
7,200
3/4
14,200
11,360
7/8
17,300
13,840
1
26,500
21,200
RIGGING HARDWARE
1-1/4
37,400
29,920
1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4
53,000 72,150 94,200 119,200 147,150 178,050
42,400 57,720 75,360 95,360 117,720 142,440
Nominal Dimensions (in.) Product Code
Material Diameter A
Inside Length B
Inside Width C
0.44
4.13
2.29
0.56
4.84
2.69
0.63
5.29
2.98
0.75
6.61
3.72
0.88
7.35
4.14
ML040 ML040NF ML050 ML050NF ML063 ML063NF ML075 ML075NF ML087 ML087NF ML100 ML100NF ML125 ML125NF ML150 ML175 ML200 ML225 ML250 ML275
1.00
7.53
4.30
1.25
9.26
5.29
1.50 1.75 2.00 2.25 2.50 2.75
11.03 12.86 14.70 16.54 18.38 20.21
6.30 7.35 8.40 9.45 10.50 11.55
Flat Dimensions (in.) Width
Thickness
0.94 – 0.94 – 1.22 – 1.41 – 1.56 – 1.56 – 1.56 – – – – – – –
0.28 – 0.28 – 2.81 – 0.40 – 0.44 0.53 0.68 – – – – – – –
Type and Size of Chain Sling (in.) Weight (lbs.)
Single
Double
0.50
7/32 & 9/32
7/32
1.02
–
7/32
1.34
3/8
9/32
2.36
1/2
3/8
3.60
–
–
5.20
5/8
1/2
9.60
3/4 & 7/8
5/8
16.20 25.10 41.00 58.00 74.90 99.80
1 – 1-1/4 – – –
3/4 7/8 1 – 1-1/4 –
NOTE: *Master link with flats are available through 1-1/4" only Part numbers with"NF" are for master links WITHOUT flats
94
C H A I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
RIGGING HARDWARE
WIDE BODY SUB-ASSEMBLY WITH FLATS HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 4,600 TO 178,050 LBS. C A
BENEFITS & FEATURES
Trade Size (in.) 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4
ƒ 100% proof tested ƒ May be used for mechanical and welded sling assemblies ƒ Extra wide body is ideal for wire rope applications ƒ Sizes up to 1-1/4" intermediate links available with flats to accommodate Omega links
Working Load Limit (lbs.) With Chain 5,750 9,000 14,000 17,300 26,500 37,400 53,000 72,150 94,200 119,200 147,150 178,050
Complete Assembly With Wire Product Rope & Code Synthetic 4,600 7,200 11,200 13,840 21,200 29,920 42,400 57,720 75,360 95,360 117,720 142,400
SA050 SA063 SA075 SA087 SA100 SA125 SA150 SA175 SA200 SA225 SA250 SA275
B 120º
E Can be used with included angles up to 120°
Flat
ƒ Designed to accept Herc-Alloy 800® chain, wire rope and synthetic attachments ƒ Durable orange powder coated finish
F
Master Link Nominal Dimensions (in.)
D
Intermediate Link Nominal Dimensions (in.)
Product Code
Material Diameter A
Inside Length B
Inside Width C
Product Code
Material Diameter D
Inside Length E
Inside Width F
ML050 ML063 ML075 ML087 ML100 ML125 ML150 ML175 ML200 ML225 ML250 ML275
0.56 0.63 0.75 0.88 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75
4.84 5.29 6.61 7.35 7.53 9.26 11.03 12.86 14.70 16.54 18.38 20.21
2.69 2.98 3.72 4.14 4.30 5.29 6.30 7.35 8.40 9.45 10.50 11.55
ML040 ML050 ML063 ML063 ML075 ML100 ML100 ML125 ML150 ML175 ML200 ML200
0.44 0.56 0.63 0.63 0.75 1.00 1.00 1.25 1.50 1.75 2.00 2.00
4.13 4.84 5.29 5.29 6.61 7.53 7.53 9.26 11.03 12.86 14.70 14.70
2.29 2.69 2.98 2.98 3.72 4.30 4.30 5.29 6.30 7.35 8.40 8.40
Weight (lbs.) 1.8 2.9 5.5 6.3 10.2 20.0 26.6 44.3 73.4 108.2 156.9 181.0
Type and Size of Chain Sling (in.) Triple
Quad
– 7/32 9/32 – 3/8 1/2 – 5/8 3/4 7/8 1 –
– 7/32 9/32 – 3/8 1/2 – 5/8 3/4 7/8 1 –
NOTE: Master link with flats are available through 1-1/4" only
® HERC-ALLOY 800 RIGGING HARDWARE
DNV MASTER SUB-ASSEMBLIES WORKING LOAD LIMIT: 17-1/2 TO 50 TON
Master Sub-Assemblies meeting DNV requirements are used to build slings in conjunction with DNV Shackles. These products are designed for use in offshore saltwater environments for general load securement applications, such as during the installation and removal of offshore platforms or transportation of cargo container units.
Working Load Limit
ƒ Designed for use with chain, wire rope and synthetic slings. ƒ Made from superior triple alloy steel with th a galvanized coating for protection against corrosion. th ƒ Certification of compliance supplied with each shipment. CG3 documentation available upon request. ƒ Available in sizes from 1-1/4" to 2" diameter. meter. Other sizes available upon request.
Master Link Dimensions (in.)
C A
Intermediate Link Dimensions (in.)
Trade Size (in.)
ton
lbs.
Product Code
Material Diameter A
Inside Length B
Inside Width C
Material Diameter D
Inside Length E
Inside Width F
Weight (lbs.)
1-1/4 1-1/2 1-3/4 2
17.64 27.56 38.59 50
35,280 55,125 77,175 100,000
SA125DNV SA150DNV SA175DNV SA200DNV
1.25 1.50 1.75 2.00
8.75 10.50 12.00 14.00
4.38 5.25 6.00 7.00
1.25 1.50 1.75 2.00
8.75 10.50 12.00 14.00
4.38 5.25 6.00 7.00
27.8 48.0 75.0 113.7
B E Flat
BENEFITS & FEATURES ƒ Certified and serialized to meet DNV 2.7-1 and 2.7-3 Offshore Container Specifications and 2.22 Lifting Appliances Requirements. ƒ Design factor of 5:1 or higher in accordance with DNV 2.7-1 requirements. ƒ Welds exceed Charpy V impact strength of 27 Joules at -20ºC (20 ft-lb, at -4ºF) as per DNV 2.7-1. ƒ Exceed ASTM A952 specifications for lifting components. ƒ Designed to meet ASME B30.9 requirements. ƒ Links are 100% proof tested at the manufacturing facility at two times the WLL.
F
D
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
95
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80) ®
MASTER RING HERC-ALLOY 800
WORKING LOAD LIMIT: 3,500 TO 141,000 LBS. BENEFITS & FEATURES ƒ Made from alloy material ƒ Proof tested at two times WLL ƒ Durable orange powder coated finish B
A
Type and Size of Chain Sling (in.)
Working Load Limit (lbs.)
Product Code
Material Diameter A
Inside Length B
Weight (lbs.)
Single
Double
Triple
Quadruple
1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2
3,500 6,100 10,500 12,300 18,400 28,300 31,300 53,000 73,500 88,900 141,000
554611 554613 554615 554617 554619 554623 554627 554630 554635 554636 554640
0.51 0.63 0.75 0.88 1.00 1.25 1.50 1.75 2.00 2.25 2.50
2.50 3.00 4.00 4.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00
0.52 0.99 1.86 2.60 3.45 6.98 11.80 18.70 27.90 39.90 54.60
7/32 & 9/32 – 3/8 1/2 5/8 3/4 – 7/8 & 1 1-1/4 – –
– 7/32 9/32 – 3/8 1/2 – 5/8 7/8 – 1
– 7/32 9/32 – – 3/8 – 1/2 5/8 3/4 7/8 & 1
– 7/32 9/32 – – 3/8 – 1/2 5/8 3/4 7/8 & 1
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
Dimensions (in.)
Trade Size (in.)
®
GRAB LINK HERC-ALLOY 800
WORKING LOAD LIMIT: 3,500 TO 18,100 LBS. BENEFITS & FEATURES ƒ Made from alloy material ƒ Proof tested at two times the WLL ƒ Economical chain adjuster for single slings ƒ Durable orange powder coated finish
B
C
D A
Dimensions (in.)
Trade Size (in.)
Working Load Limit (lbs.)
Product Code
1/2 3/4 1 1-1/4
3,500 7,100 12,000 18,100
554320 554326 554332 554337
Diameter A 0.56 0.75 1.00 1.25
Inside Length Inside Width B C 5.50 6.06 7.63 9.25
2.50 2.75 3.50 4.38
Inside Width D 0.54 0.63 0.75 1.00
Weight (lbs.) 1.01 2.08 4.59 9.16
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
79
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80) ®
OMEGALOK CONNECTOR HERC-ALLOY OYY 800 WORKING LOAD LIMIT: 3,500 TO 18,100 LBS. BENEFITS & FEATURES ƒ Fraction and metric markings ƒ Durable orange powder coated finish ƒ 100% proof tested ƒ Fatigue rated to Grade 80 specifications ƒ For use with master link with flats (see page 77)
D E
T
G
M
L PIN
H B
Size (in.) 9/32 3/8 1/2 5/8
Product Code Working Load Limit Standard Completed Load Retainer Package (lbs.) Unit Pin Pin 3,500 7,100 12,000 18,100
12 12 12 5
644128 644138 644150 644162
595780 595781 595782 595785
602326 495821 495822 495823
Dimensions (in.) B
D
E
G
H
L
M
T
Weight (lbs.)
1.36 1.90 2.31 2.87
2.30 2.82 3.52 4.46
0.98 1.25 1.56 2.00
2.81 3.57 4.44 5.45
0.33 0.45 0.59 0.75
0.36 0.51 0.63 0.75
1.45 1.77 2.26 2.72
0.43 0.57 0.70 0.88
0.40 1.02 1.92 3.20
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS ®
HAMMERLOK HERC-ALLOY 800
®
WORKING LOAD LIMIT: 2,100 TO 72,300 LBS. BENEFITS & FEATURES ƒ Used for overhead lifting slings to connect chain branches to the master link and the hook to attachments. ƒ Constructed of drop forged alloy steel ƒ Can be used with Grade 80 chain ƒ Must be matched to chain size ƒ Do not use for chain repair or splicing ƒ Meets ASTM A952 standards.
80
Completed Unit
Load Pin Kit
Dimensions (in.)
Size (in.)
Working Load Limit (lbs.)
Product Code
Weight (lbs.)
Standard Package
Product Code
Weight (lbs.)
A
B
C
D
E
F
G
7/32 9/32 3/8 1/2 5/8 3/4 7/8 1 1-1/4
2,100 3,500 7,100 12,000 18,100 28,300 34,200 47,700 72,300
664021-2 664028-2 664038-2 664050-2 664062-2 664075-2 664089-2 664100-2 664125-2
0.12 0.26 0.59 1.42 2.35 3.67 5.98 9.47 16.61
36 36 36 24 12 12 6 – –
R664021-2 R664028-2 R664038-2 R664050-2 R664062-2 R664075-2 R664089-2 R664100-2 R664125-2
0.01 0.02 0.05 0.12 0.20 0.30 0.40 0.70 1.20
0.25 0.34 0.48 0.66 0.78 0.96 1.16 1.32 1.57
0.25 0.31 0.50 0.70 0.81 0.94 1.05 1.25 1.53
1.40 1.94 2.41 3.51 4.06 4.78 5.25 6.00 6.81
0.50 0.75 0.88 1.29 1.50 1.80 1.97 2.31 2.17
0.58 0.70 0.91 1.41 1.70 1.97 2.09 2.37 2.98
1.21 1.51 2.09 2.96 3.52 4.11 4.95 5.87 7.04
0.44 0.56 0.80 1.15 1.40 1.71 1.88 2.33 2.67
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80) ®
CLEVLOK SLING HOOK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 2,700 TO 35,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Available with and without a latch ƒ Quench and tempered alloy steel ƒ Clevlok head design ƒ 100% proof tested and fatigue rated ƒ Durable orange powder coated finish ƒ Improved forged latch (hook available with or without latch) ƒ Replacement pin and latch kit available ƒ New CE compliant hooks and latches ƒ Meets EN 1677, ASTM A953 and ASME B30.10 standards
O H
H
L
L M (MIN)
R
G
R
G
M (MIN)
P
P
I
Size (in.) 7/32 9/32 3/8 1/2 5/8 3/4
Working Load Limit Standard Package (lbs.) 2,700 4,300 8,800 15,000 22,600 35,300
10 10 10 5 5 Bulk
D
Product Code With Latch
Without Latch
657716 657718 657719 657720 657721 657722
557716 557718 557719 557720 557721 557722
Latch Kit
Dimensions (in.) D
G
H
I
L
M
O
P
R
Weight (lbs.)
3.05 3.53 4.54 5.48 6.20 7.63
5.00 5.55 6.93 8.28 9.61 11.79
0.31 0.38 0.47 0.58 0.71 0.88
0.66 0.75 1.00 1.33 1.47 1.88
0.28 0.36 0.51 0.63 0.75 0.94
0.96 0.83 1.06 1.38 1.69 2.09
1.13 1.32 1.34 1.87 2.11 2.55
0.94 1.11 1.51 1.55 1.83 2.51
3.45 3.75 4.58 5.59 6.44 7.74
1.10 1.20 2.21 4.22 6.64 11.22
Alloy Load Retaining Pin Pin
4X455321 SP595778 4X455322 595780SP 4X455325 595781 4X455328 595782 4X455329 SP595783P 4X455330 595786
495826 495825 495825 495823 495849 495824
EYE SLING HOOK DUAL RATED FOR USE WITH HA800 OR HA1000
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
D
WORKING LOAD LIMIT: 2,700 TO 72,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Available with and without latch ƒ Quench and tempered alloy steel ƒ 100% proof tested ƒ Fatigue rated ƒ Hook available with and without latch (replacement latch available) ƒ Durable orange powder coated finish
B H L
M
N
O
E
S I
P
K
D
Size (in.)
Working Load Limit (lbs.)
Standard Package
7/32 9/32 3/8 1/2 5/8 3/4 7/8* 1* 1-1/4*
2,700 4,300 8,800 15,000 22,600 35,300 34,200 47,700 72,300
10 10 10 5 5 Bulk Bulk Bulk Bulk
Product Code With Latch
Without Latch
558618 558622 558625 558628 558629 558630 558332 558333 558335
458618 458622 458625 458628 458629 458630 458732 458733 458735
G
Dimensions (in.) Latch Kit
B
4X458321 1.50 595523 1.63 595525 2.06 595528 2.63 595529 3.06 595530 3.50 595532 3.88 595533 4.31 595535 5.31
D
E
G
H
I
K
L
M
N
O
P
S
Weight (lbs.)
3.04 3.50 4.33 5.50 6.34 7.83 8.59 9.59 11.56
1.03 1.50 1.88 2.25 2.63 3.00 3.38 4.00 4.66
5.06 5.25 6.64 8.16 9.66 11.38 12.72 14.23 17.00
0.38 0.44 0.56 0.75 0.88 1.00 1.09 1.22 1.50
0.66 0.73 0.95 1.17 1.44 1.69 1.94 2.14 2.62
1.48 1.59 2.19 2.56 2.63 3.44 3.88 4.25 4.64
0.75 0.75 0.94 1.13 1.31 1.50 1.69 1.88 2.31
3.75 3.75 4.78 5.69 6.50 7.81 8.75 9.88 11.50
1.17 1.19 1.44 1.78 2.03 2.50 2.78 3.13 3.88
0.98 1.20 1.45 1.94 2.38 2.83 3.22 3.55 4.25
0.94 1.05 1.28 1.66 2.19 2.51 2.84 3.09 3.89
0.96 1.06 1.31 1.63 1.75 2.19 2.38 2.88 3.41
0.8 1.10 1.90 4.30 7.30 12.50 18.10 22.60 47.00
* Herc-Alloy 800® only
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
81
RIGGING HARDWARE
RIGGING HOOK WORKING LOAD LIMIT: 3/4 TO 15 TONS BENEFITS & FEATURES ƒ Load rating marked on each hook body ƒ Design factor 5:1 ƒ Pre-drilled latch tab allows addition of latch ƒ Carbon hooks have a clear protective coating to resist rust and for cleaner handling ƒ Alloy hooks have orange powder coated finish
Standard Package
10 10 5 5 5 5 – – –
B
L R
T G
without Latch
with Latch
Zinc Plated Latch Kit (optional) Product Code
M6402A M6403A M6404A M6405A M6407A M6409A M6411A M6415A M6422A
M6502A M6503A M6504A M6505A M6507A M6509A M6511A M6515A M6522A
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309 4X1311 4X1315 4X1322
Clear Finish
Painted Orange
3/4 1 1-1/2 2 3 5 7-1/2 10 15
without Latch
with Latch
M6402C M6403C M6404C M6405C M6407C M6409C M6411C M6415C M6422C
M6502C M6503C M6504C M6505C M6507C M6509C M6511C M6515C M6522C
WLL* (tons) 1 1-1/2 2 3 5 7 11 15 22
K D
H
Alloy
Product Code
J O K
Carbon
WLL* (tons)
A
C
Product Code
Dimensions (in.)
A
B
C
D
G
H
J
K
L
O
R
T
1.50 1.75 2.13 2.50 3.08 3.88 4.69 5.34 6.63
0.75 0.88 1.10 1.25 1.56 1.98 2.44 2.84 3.50
0.38 0.44 0.50 0.64 0.77 0.94 1.13 1.25 1.56
3.12 3.37 3.80 4.20 5.11 6.24 7.89 8.53 10.30
0.87 0.94 1.06 1.26 1.44 1.82 2.25 2.75 3.15
1.01 1.11 1.21 1.43 1.63 2.01 2.63 3.10 3.62
0.93 0.97 1.02 1.19 1.50 1.78 2.38 2.50 3.30
0.63 0.71 0.74 0.94 1.38 1.68 1.88 2.03 2.60
4.37 5.04 5.65 6.55 7.97 10.07 12.41 14.05 17.53
0.93 0.97 1.02 1.16 1.41 1.69 2.19 2.30 3.12
3.13 3.66 4.09 4.67 5.78 7.31 9.03 10.21 12.81
0.87 0.97 1.03 1.16 1.53 1.94 2.52 2.54 2.73
Latch Kit
Weight (lbs.)
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309 4X1311 4X1315 4X1322
0.66 1.12 1.46 2.42 4.10 8.16 15.60 21.58 39.89
* Working Load Limits in Metric Tons. Note: Other finishes are available as special orders.
SWIVEL RIGGING HOOK RIGGING HARDWARE
WORKING LOAD LIMIT: 1 TO 22 TONS BENEFITS & FEATURES ƒ Design factor 5:1 ƒ Pre-drilled for latches ƒ Hooks furnished with or without latches ƒ Powder coated orange ƒ Hooks are heat treated, quenched and tempered
A C S
B
R
L
O
I
T G H D
Standard Package 10 10 10 10 10 Bulk Bulk Bulk Bulk
WLL* (tons) 1 1-1/2 2 3 5 7 11 15 22
Alloy Product Code without Latch
with Latch
Zinc Plated Latch Kit (optional) Product Code
M3402A M3403A M3404A M3405A M3407A M3409A M3411A M3415A M3422A
M3502A M3503A M3504A M3505A M3507A M3509A M3511A M3515A M3522A
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309 4X1311 4X1315 4X1322
Dimensions (in.)) A
B
C
D
G
H
I
2.00 2.50 3.00 3.00 3.50 4.75 5.50 6.00 7.75
1.11 1.38 1.65 1.65 1.77 2.39 2.55 2.47 3.82
1.31 1.50 1.75 1.75 2.00 2.75 3.25 3.50 4.75
3.06 3.33 3.67 4.20 5.11 6.24 7.69 8.37 10.19
0.87 0.94 1.06 1.27 1.44 1.82 2.25 2.59 3.00
1.05 1.11 1.21 1.43 1.63 2.01 2.63 2.94 3.50
0.63 0.71 0.88 0.94 1.31 1.68 1.88 2.19 2.69
L
R
5.83 4.63 6.83 5.44 7.76 6.25 8.40 6.49 9.76 7.53 12.42 9.67 14.89 12.06 15.79 11.95 21.18 16.68
S
T
O
Latch Kit
Weight (lbs.)
0.38 0.50 0.63 0.63 0.75 1.00 1.13 1.25 1.50
0.87 0.97 1.03 1.16 1.53 1.94 2.46 2.62 2.74
0.93 0.97 1.06 1.16 1.41 1.69 2.22 2.23 3.05
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309 4X1311 4X1315 4X1322
1.05 1.56 2.50 3.20 5.36 10.56 19.00 26.75 51.80
* Working Load Limits in Metric Tons
90
C H A I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
RIIGGING G & AT ATTACH CHME CH MENT ME NTS NT S CHAIN SLINGS &®COMPONENTS HERC-ALLOY 800 (GRADE 80) ®
CLEVLOK GRAB HOOK WITHOUT CRADLE HERC-ALLOY 800 ®
WORKING LOAD LIMIT: 3,500 TO 18,100 LBS. BENEFITS & FEATURES ƒ Quench and tempered alloy steel ƒ Fatigue rated ƒ Built without lugs to avoid catching when slipping into tight clearance ƒ Durable orange powder coated finish ƒ Replacement pin available
B
H
L
E M
G
K P T
D
Size (in.)
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
9/32 3/8 1/2 5/8
Product Code Working Load Limit Standard Completed Load Retainer Package (lbs.) Unit Pin Pin 3,500 7,100 12,000 18,100
10 10 5 5
659232 659235 659238 659239
595780 595781 595782 595783
602326 495821 495822 495823
Dimensions (in.) B
D
E
G
H
K
L
M
P
T
Weight (lbs.)
1.36 1.90 2.31 2.87
1.91 2.78 3.62 4.41
0.36 0.47 0.59 0.75
3.70 4.81 6.35 7.74
0.33 0.45 0.59 0.75
1.04 1.49 1.98 2.39
0.36 0.51 0.63 0.75
2.29 2.87 3.78 4.82
0.76 1.03 1.51 1.80
0.81 1.06 1.38 1.69
0.6 1.3 2.5 4.4
Note: If used as a choker, working load limit should be reduced by 20%.
®
CLEVLOK CRADLE GRAB HOOK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 2,700 TO 28,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Unique cradle grab design ƒ Quench and tempered alloy steel ƒ Fatigue rated ƒ Durable orange powder coated finish ƒ Replacement pin available
J
H L G M
R
P K
D
Dimensions (in.)
Size (in.)
Working Load Limit (lbs.)
Product Code
Standard Package Quantity
D
G
H
J
K
L
M
P
R
Weight (lbs.)
7/32 9/32 3/8 1/2 5/8 3/4*
2,700 4,300 8,800 15,000 22,600 28,300
659718 659722 659725 659728 659729 659430
10 10 10 5 5 Bulk
1.62 2.18 2.72 3.65 4.50 5.23
3.21 3.39 4.33 5.27 6.54 9.08
0.31 0.38 0.47 0.65 0.77 0.88
0.75 0.82 1.18 1.39 1.55 2.05
0.94 0.97 1.29 2.01 2.42 2.88
0.28 0.36 0.51 0.63 0.75 0.91
0.31 0.38 0.74 0.60 0.77 0.88
0.62 0.82 1.03 1.19 1.41 1.87
1.98 1.86 2.47 3.04 3.76 5.50
0.50 0.63 1.30 2.10 4.20 10.24
* 3/4" is Herc-Alloy 800® only. Hook shape/style differs from photo and dimension drawing shown. Note: If used as a choker, working load limit should be reduced by 20%.
82
C HA I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
R GG RI GGIN ING IN G & AT ATT TACH HMENT NT TS CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80)
EYE CRADLE GRAB HOOK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 3,200 TO 72,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Unique cradle grab design ƒ Quench and tempered alloy steel ƒ 100% proof tested ƒ Fatigue rated ƒ Durable orange powder coated finish
B L
H
M E
G
K P
Dimensions (in.)
Size (in.)
Working Load Limit (lbs.)
Standard Package
Product Code
B
D
E
G
H
I
K
L
M
P
Weight (lbs.)
7/32 9/32 3/8 1/2 5/8 3/4 7/8* 1* 1-1/4*
3,200 4,300 8,800 15,000 22,600 35,300 34,200 47,700 72,300
10 10 10 5 5 Bulk Bulk Bulk Bulk
559724 559725 559737 559750 559762 559775 559387 559100 559124
1.20 1.40 1.78 2.28 2.75 3.50 3.75 4.31 5.38
1.68 1.93 2.86 3.63 4.53 5.23 5.69 7.00 8.50
0.31 0.36 0.47 0.59 0.75 0.91 1.00 1.19 1.53
3.22 3.72 4.81 6.36 7.62 9.54 9.63 12.44 15.56
0.33 0.39 0.52 0.63 0.75 1.00 1.00 1.22 1.56
0.92 1.07 1.65 1.81 2.13 2.88 3.00 3.88 2.50
0.99 1.13 1.49 2.15 2.65 3.52 3.75 4.31 5.50
0.55 0.63 0.78 1.06 1.22 1.52 1.75 1.88 2.25
2.20 2.57 3.27 4.23 5.06 6.70 6.50 8.09 10.50
0.69 0.76 1.02 1.53 1.80 1.85 2.12 3.12 3.50
0.35 0.55 1.06 2.00 5.40 9.00 10.40 20.90 40.00
* Herc-Alloy 800® only Note: If used as a choker, working load limit should be reduced by 20%.
HERC-ALLOY 800® CHAIN SLINGS & COMPONENTS
I
D
EYE FOUNDRY HOOK DUAL RATED FOR USE WITH HA800 OR HA1000 WORKING LOAD LIMIT: 4,300 TO 72,300 LBS. BENEFITS & FEATURES ƒ For use with both Grade 80 & 100 chain ƒ Throat opening up to 6" ƒ Quench and tempered alloy steel ƒ Fatigue rated ƒ Durable orange powder coated finish
H
B L
G (REF)
N
M I
O
R (SPHER.)
E K
D (REF)
Size (in.) 9/32 3/8 1/2 5/8 3/4 7/8* 1* 1-1/4*
Working Load Limit Standard Package (lbs.) 4,300 8,800 15,000 22,600 35,300 34,200 47,700 72,300
5 5 5 5 Bulk Bulk Bulk Bulk
Dimensions (in.)
Product Code
B
D
E
G
H
I
K
L
M
N
O
R
Weight (lbs.)
474798 474799 474800 474801 474802 474503 474504 474505
1.56 2.00 2.50 3.00 3.50 4.00 4.50 5.13
4.73 5.72 6.75 7.81 9.10 10.09 11.55 12.87
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00
6.45 7.88 9.38 10.97 12.81 14.23 16.17 18.03
0.47 0.63 0.75 0.88 1.00 1.13 1.29 1.38
1.00 1.27 1.50 1.81 2.20 2.25 2.63 3.17
1.56 1.88 2.22 2.63 3.00 3.38 3.75 4.25
0.63 0.80 1.00 1.25 1.50 1.70 2.13 2.33
4.75 5.77 6.88 8.06 9.25 10.38 11.56 12.88
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00
1.23 1.50 1.75 2.03 2.56 2.78 3.45 3.81
0.25 0.31 0.38 0.44 0.50 0.56 0.62 0.75
2.4 4.5 7.1 11.6 20.0 26.0 36.8 58.4
* Herc-Alloy 800® only
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
83
RIGGING HARDWARE
®
SORTING HOOK HERC-ALLOY 800 WORKING LOAD LIMIT: 7-1/2 TONS BENEFITS & FEATURES ƒ 5:1 design factor ƒ Quench and tempered alloy steel ƒ Long tapered point designed for easy grab in rings, pear links, eye bolts or lifting holes ƒ Durable orange powder coated finish ƒ Do not load last 1" of the tip
A
M
C
B E D
I H
G F
Working Load Limit (lbs.)
With Handle
Without Handle
Dimensions (in.)
At Tip (ton)
At bottom of Hook (ton)
Product Code
Weight (lbs.)
Product Code
Weight (lbs.)
A
B
C
D
E
F
G
H
I
M
1
7-1/2
M129H
7.0
M129
6.8
3
1.44
0.78
7.34
3.75
1.28
1.25
3.93
10.09
6.58
®
SHANK HOOK HERC-ALLOY 800 WORKING LOAD LIMIT: 1 TO 7 TONS
RIGGING HARDWARE
BENEFITS & FEATURES ƒ Heat treated alloy steel provides strength without bulk or weight ƒ Pre-drilled boss allows for latch ƒ Shank hooks are supplied unthreaded, but can be supplied threaded as a special order item ƒ Shank hooks made from other material (bronze, stainless steel, etc.) available upon request
Z
X
H Y O
Z
J w/o Latch L R F
K
P G
T
K
D
Alloy Shank Hook Latch Max Kit Shank Latch Working Product Weight Hole (lbs.) Product Diameter Load Limit (in.) Code Code (in.) (ton) 1 1-1/2 2 3 5 7
M1302A M1303A M1304A M1305A M1307A M1309A
0.65 0.80 1.47 1.85 4.04 7.25
4X1302 4X1303 4X1304 4X1305 4X1307 4X1309
0.72 0.79 0.86 1.11 1.30 1.56
0.14 0.19 0.18 0.18 0.20 0.20
Dimensions (in.) D
F
G
H
J
3.09 3.37 3.75 4.23 5.16 6.24
1.25 1.38 1.50 1.63 2.00 2.50
0.87 0.94 1.04 1.25 1.44 1.82
1.01 1.11 1.21 1.43 1.63 2.01
0.91 0.97 1.06 1.17 1.48 1.78
K
L
0.63 5.44 0.71 5.92 0.88 6.45 0.94 7.42 1.38 8.80 1.68 10.72
O
P
R
X
Y
Z
0.88 0.91 1.00 1.16 1.41 1.69
2.12 2.27 2.58 2.84 3.52 4.59
2.35 2.59 2.75 3.16 3.85 4.70
0.66 0.73 0.79 0.96 1.24 1.49
2.22 2.39 2.66 3.01 3.52 4.02
0.69 0.80 1.00 1.03 1.27 1.56
The following should be observed: V Shanks are not intended for internal threading or swaging. V To obtain maximum strength threads should be class 1 or 2. V Thread engagement in nut or object must be a minimum of 1-1/2 times the thread diameter. Insufficient thread engagement can result in loss of load.
88
C H A I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
RIGGING HARDWARE
®
PLATE HOOK HERC-ALLOY 800
WORKING LOAD LIMIT: 3,600 TO 11,400 LBS. BENEFITS & FEATURES ƒ Made from alloy material ƒ Designed to handle plate steel ƒ Durable orange powder coated finish ƒ Available as components or attached to certified slings
T L R D M
C
R
A
B
N
R W
Size (in.)
Working Product Load Limit Code (lbs.)
9/32 3/8 1/2
462528 462537 462550
3,600 7,050 11,400
Dimensions (in.) A
B
C
D
L
M
N
T
W
R
2.00 2.63 3.50
1.75 2.97 4.00
2.50 4.31 4.38
0.94 1.24 1.50
1.00 1.13 1.50
3.48 6.53 6.98
0.13 0.19 0.28
0.63 0.75 1.00
2.50 2.75 3.50
0.31 0.50 0.50
Weight (lbs.) 2.80 5.70 13.00
Other sizes available
NEVER USE PLATE HOOKS ON A QUAD SLINGS. To lift a plate with a quad sling, a spreader or beam is required and hooks would go on the end of double chain slings that would be attached to each end of the beam.
® ® HERC-ALLOY 800 RIGGING HARDWARE
ALLOY “S” HOOK HERC-ALLOY 800 WORKING LOAD LIMIT: 210 TO 6,250 LBS. BENEFITS & FEATURES ƒ Made from alloy material ƒ Proof tested at two times WLL ƒ Durable orange powder coated finish ƒ WLL embossed on hooks ƒ Custom sizes available upon request ƒ Serialized upon request
D C
A C
B
Size (in.)
Working Load Limit (lbs.)
Product Code
9/32 3/8 1/2 5/8 3/4 7/8 1 1-5/32 1-1/4 1-3/8 1-1/2
210 410 870 1,120 1,730 2,370 2,920 3,150 4,450 6,100 6,250
562228 562237 562250 562262 562275 562287 562300 562310 562325 562337 562350
Dimensions (in.) A
B
C
D
Weight (lbs.)
0.28 0.38 0.56 0.63 0.75 0.88 1.00 1.13 1.25 1.38 1.50
4.50 6.00 7.50 9.00 10.50 12.00 13.00 15.00 16.00 17.00 18.00
1.13 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00
1.13 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00
0.15 0.35 1.04 1.56 2.60 4.20 6.00 9.30 11.70 15.40 19.50
CHAI N & R I GGI NG ATTACHMEN TS (C MR P -6) W WW. C M W O R K S . CO M
PHONE: 800.888.0985
89
RIGGING HARDWARE
REPLACEMENT HOOK WITH LATCH WORKING LOAD LIMIT: 1 TON D
BENEFITS & FEATURES ƒ Easy installation ƒ Bolt, nut, and cotter pin provides safe and secure attaching points ƒ Self colored finish ƒ Easy installation
E
B
A
C
Working Load Limit (ton)
Product Code
A
B
C
D
E
Weight (lbs.)
1
M134
7.56
5.63
1.13
0.50
0.44
2.56
Dimensions (in.)
CLB CONTAINER LIFTING LUGS WORKING LOAD LIMIT: 88,100 LBS. (PER SET OF 4)
Supplied in sets of 4, CLB Lifting Lugs serve as flexible lashing points for the transportation of containers.
RIGGING HARDWARE
BENEFITS & FEATURES ƒ Spring-loaded bolt to prevent accidental release ƒ Mounted horizontally at the side of the container in either upper or lower holes ƒ Easy installation and removal – simply insert and turn to install ƒ Designed to eliminate the dangerous use of standard hooks
ƒ Lugs cannot drop out when slings become slack ƒ Lugs can be used for left hand or right hand turns ƒ For maximum capacity, use a lifting beam in conjunction with CLB lifting lugs
G
50T Vertical
D
40T 20
C E
B
36º 32T 50º
F
A
92
Dimensions (in.)
Product Code
Working Load Limit (lbs. per set of 4)
A
B
C
D
E
F
G
Weight (lbs.)
CLB40
88,100
5.984
7.126
1.772
1.457
2.874
2.953
1.575
39.7
REDUCTION OF WORKING LOAD LIMIT Angle of lift must be specified when ordering CLB lifting lugs
C H A I N & R I G G I N G AT TA CHM ENT S (CM RP -6 )
PHONE: 800.888.0985
WWW.C M W OR K S .C OM
Related Documents 3h463d
Cadena 4k2a6c
July 2022 0
Cadena 4k2a6c
February 2023 0
Cadena Absro 1d3gp
August 2020 0
Cadena Alimenticia 334a3x
April 2021 0
Cadena Original 2q6x3p
December 2019 38