Harris Welding Tip Chart 3nu65

Harris 23A90, 5090, 1390, & 8490 Thickness Chart Metal Thicknes Oxygen Acetylen Tip Size PSIG e PSIG s 0 1/ 64 1 1 1 1/ 32 1 1 2 3/ 64 2 2 3 1/ 16 3 3 4 3/ 32 4 4 5 1/ 8 5 5 6 3/ 16 6 6 7 1/ 4 7 7 8 5/ 16 8 8 9 3/ 8 9 9 10 1/ 2 10 10 13 3/ 4 13 13 15 1 15 15

Cutting Tip Data IMPORTANT:Use proper type seat cutting tips for each type of torch and fuel gas. Use proper type tips for fuel gases or acetylene.See manufacture's chart for proper tip selection. Use proper tip size, pressures and flamesize to avoid backfire and flashback. Torch and Tip Types Victor Airco Harris Type Type Type Seat 2 Seat 3 Seat 2 tapper tapper flat 1-101 3Metal 101 5Thicknes 101 GPM144 164 6290 s N-P 1/8" 0 0 0 1/4" 0 0 0 3/8" 0 1 0 1/2" 0 1 0 3/4" 1 2 1 1" 2 2 1 1-1/2" 2 3 2 2" 3 3 3 2-1/2" 3 4 3 3" 4 5 4 4" 5 5 4 5" 5 6 4 6" 6 6 5 8" 6 6 5 10" 7 7 6 12" 8 8 6

Oxygen

PSIG 20-25 20-25 25-30 30-35 30-40 35-50 40-50 40-55 45-55 45-60 45-60 50-65 50-70 55-75 68-85 55-95

Acet./Fuel Gas

SCFH 25 35 60 65 85 140 160 180 230 280 350 420 450 600 700 900

PSIG 5 5 5 5 5 6 7 9 10 10 12 12 12 14 14 14

SCFH 5 6 8 10 13 16 18 22 26 30 34 38 40 44 50 55

Speed IPM 28-32 25-30 24-28 20-24 17-20 15-20 17-Dec 15-Dec 13-Oct 12-Sep 11-Aug 9-Jul 8-Jun 6-May 5-Apr 5-Mar

CUTTING OXYGEN PRESSURE GUIDE Type 101 etc. Victor type seat, tube mix lower psig. Type 144 etc. Airco type seat, tip mix mid psig. Type 6290 etc. Harris type seat, head mix upper psig. SCFH, std. cu. ft. per hr. PSIG, pounds per square inch guage WARNING: Do not operate this equipment until you fully understand its safe and proper use. The safe and effective use of the equipment depends on the fully understanding and carefully following practical time-tested safety operation instructions to prevent and avoid unnecessary painful injuries and costly property damages and losses. Read all operating instructions carefully before using equipment. Do not light torch until all connections are leak tight. Purge out torch before lighting. WARRANTY CLAUSE:Uniweld believes the information contained herein to be reliable. However, the technical information is given by Uniweld without charge and the shall employ such information at his own discretion and risk. Uniweld assumes no responsillity for results or damages incurred from the use of such information in whole or in part.

Weld/Braze Tip Data IMPORTANT: Use proper type of tip for each type torch

Victor Type Weld/ Seat Braze Type Tips 1, 4, 13, Metal 17 Thicknes s Size Up to 1/32" 0 1/16"3/64" 0 1/32 5/64 0 3/64 3/32 1 1/16 1/8 2 1/8 3/16 3 3/16 1/4 4 1/4 1/2 5 1/2 3/4 6 3/4 1-1/4 7 1-1/4" 2" 8 2-1/2" 3" 10 3-1/2" 4" 12

N U M B E R Drill Size

D E C I M A L Size

75

-0.02

70 65 60 56 53 49 43 36 30

-0.03 -0.04 -0.04 -0.05 -0.06 -0.07 -0.09 -0.11 -0.13

29

-0.14

27

-0.14

25

-0.15

Harris Type Seat

N U M B E R Drill Size

D E C I M A L Size

Airco Type Seat

N U M B E R Drill Size

D E C I M A L

Type 79 Size 0

70

-0.03

Type 96 Size 0

76

-0.02

1

67

-0.03

0

72

Size

-0.03

2 3 4 5 6 7 8 9 10

62 57 56 55 53 50 47 43 40

-0.04 -0.04 -0.05 -0.05 -0.06 -0.07 -0.08 -0.09 -0.1

1 2 3 4 5 6 7 8 9

68 62 56 54 51 48 45 40 35

-0.03 -0.04 -0.05 -0.06 -0.07 -0.08 -0.08 -0.1 -0.11

10

30

-0.13

Pressure** Oxy psi Acet psi

Acet scfh**

5-Mar

5-Mar

2-Jan

5-Mar 5-Mar 5-Mar 5-Mar 7-Apr 10-May 12-Jun 14-Jul 16-Aug

5-Mar 5-Mar 5-Mar 5-Mar 6-Mar 7-Apr 8-May 9-Jun 10-Aug

1.5-3 4-Feb 6-Mar 10-May 18-Aug 25-Oct 15-35 25-45 30-60

19-Oct

12-Sep

35-75

24-Dec

15-Dec

50-100

18-28

15-Dec

80-160

* The approx. Oxygen consumption ration for various gasses is as follows: 1 oxygen to 1 acetylene 2 oxygen to 1 Mapp®/Natural gas 4 oxygen to 1 propane/propylene Gas consumption data is merely for estimating purposes. It will vary due to the material, skill of the operator and working conditions **Use same pressures for fuel gas for brazing and one size or larger tip. Pressures are approximate for hose lenght up to 25ft, increase for longer lengths about 3 psi for every 25ft, increase working pressure 2-3 psi for check valves.NOTE: Oxy-acetylene must be used to produce satisfactory welds in steel. Acetylene cylinder gas withdrawal should not exceed 1/7 (15%) of cylinders contents per hour. Do not allow gas cylinders (especially oxygen) to empty in use - this can cause unbalanced pressures and reverse flow of gasses. An adequate cylinder of manifold system should be provided for large gas usage operations with 3/8" hose for larger size tips. Approximate heat output B.T.U./HR. per cubic foot: acetylene 1470, propane 2498, Mapp® 2406 propylene 2371, natural gas 1000. SCFH, std. cu. ft. per hr. PSIG, pounds per square inch guage. WARNING: Do not operate this equipment until you fully understand its safe and proper use. The safe and effective use of the equipment depends on the fully understanding and carefully following practical time-tested safety operation instructions to prevent and avoid unnecessary painful injuries and costly property damages and losses. Read all operating instructions carefully before using equipment. Do not light torch until all connections are leak tight. Purge out torch before lighting. WARRANTY CLAUSE:Uniweld believes the information contained herein to be reliable. However, the technical information is given by Uniweld without charge and the shall employ such information at his own discretion and risk. Uniweld assumes no responsillity for results or damages incurred from the use of such information in whole or in part.

Heating Tip Data Acetylen e/Fuel Gas Oxygen Heating Pressure* Pressure* Tips ** ** OxyRange Range Acetylen e PSIG PSIG or Fuel Gas Tip Size Type 11, 12 5 10-Jul 15-Oct Victor Type Seat 6 10-Jul 15-Oct Type 11H+ 8 15-Oct 20-30 Harris Type Seat 10* 15-Dec 25-40 Type 911 12* 15-Dec 40-60 Airco Type 15* 15-Dec 40-60 Seat Type 28, 29 Victor Type Tip Type 79282 7-May 8-May 79+ 7928-43 4 7-May 12-Aug Harris Type Tip 6 12-Aug 15-Oct Type 37 8 15-Oct 20-30 Airco Type Tip Type 13, 17 Victor Type Seat 15,30 12-Aug 20-Oct

Acetylen Oxygen e SCFH SCFH 20-Jun 14-40

25-Jul 15-45

30-80

35-90

40-100 60-150

45-115 70-170

90-220

100-250

9-Mar 20-Jul

10-Apr 20-Oct

14-40 30-80

15-45 35-90

15, 30

17, 33

+ Oxy/Acetylene/equal pressures for Harris type tips Heating Tips Fuel Gas (Not Acetylen e) Type 45 Victor Type Tip Type 945 Airco Type Tip 2290-H Harris Type Tip

Oxygen Fuel Gas Pressure* Pressure* ** ** Consumption, SCFH Tip Size 10*

PSIG 70/100

PSIG 15/25

Oxygen Fuel Gas 350/480 150/200

15* 20*

90/120 20/35 100/150 30/50

600/800 250/350 900/1150 400/500

2290-1H 25-Oct 2290-2H* 15/45 2290-3H* 25/70 2290-4H* 50/110 2290-5H* 60/135

12-Apr 160/320 40/80 22-Jul 220/520 55/130 25-Aug 340/920 85/230 30-Oct 640/1300 160/325 720/1600 180/400 14/40

* Use 3/8" hose on large tips for more gas flow. ** Type 12 for fule gas only (Not Acetylene) ***IMPORTANT:Use maximum pressure on large heating tips to avoid backfire and flashback conditions from low gas flows. Fuel gas flame must have excessive smoking cleared to provide adequate gas flow increase fuel regulator pressure enough to clear smoke from flame. SCFH, std. cu. ft. per hr. PSIG, pounds per square inch guage WARNING: Do not operate this equipment until you fully understand its safe and proper use. The safe and effective use of the equipment depends on the fully understanding and carefully following practical time-tested safety operation instructions to prevent and avoid unnecessary painful injuries and costly property damages and losses. Read all operating instructions carefully before using equipment. Do not light torch until all connections are leak tight. Purge out torch before lighting. WARRANTY CLAUSE:Uniweld believes the information contained herein to be reliable. However, the technical information is given by Uniweld without charge and the shall employ such information at his own discretion and risk. Uniweld assumes no responsillity for results or damages incurred from the use of such information in whole or in part.

Hooper Welding Supply 1806 N MacArthu r OK OK 73122 Phone 405-7891511 Fax 405601-2758

Features: Equipped with FlashGuard® check valves Capacity: cuts 4", welds to 1/2" Length: 7 3/4", Weight: 0.9 lbs Part Number

Model Number

Torch Type

Torch Length

Length

Weight

Cutting Tip

Brazing Tip

Series

Accessories

1401016

16

Combination Handle

7 3/4"

7 3/4"

0.9 lbs

3690-P, 3690

5090, 1390, 1390-N, 23n-90

16

D50C Tip Tube, D50C XL, 8593, TH-50-2 & TH-5-2XL

Part Number

Fuel Gas

Certifications

Mixer

Cutting Attachment

Inlet

Mixing System

1401016

Oxyacetylene/Hy drogen Oxypropane/But ane Oxy-natural Gas/Methan e Oxypropylene

UL

H-16-E, H16-S, H-162E

36-2

"B" 9/16"-18 R+LH

E&F

Model 16

Description: Medium Duty Combination Handle The Harris 16 combination torch handle for cutting, welding, brazing and heating. It can be used with oxy-acetylene or other fuel gases. The Model 16 features silver brazed twin tube construction.

Contains all the quality equipment needed for cutting, welding and brazing in a rugged molded plastic carrying case. The outfit is designed to carry one MC acetylene cylinder and one 20 cu. ft. oxygen cylinder. As supplied, the outfit is capable of cutting to 1" and welding to 1/16". Can cut to 4" and weld to 1/2" with larger tips and acetylene cylinders.

PART#

MODEL NUMBER

HANDLE

MIXER

CUTTING ATTACH

CUTTING TIP

WELDING TIP

OXYGEN REGULATOR

FUEL GAS REGULATOR

4403078

16601-200-DLX

16

H-16-2E

71-3

6290-1AC

23A90-3

601-100-540 (3000296)

601-15-200 (3000295)

4403077

16601-200-STD

16

H-16-2E

71-3

6290-1AC

23A90-3

601-100-540 (3000296)

601-15-200 (3000295)

ACCESSORIES Goggles, Striker,12’ 3/16” Hose, 20 Cu.Ft. Oxy Cyl.,10 CU.FT. “MC” ACTE. CYL. (shipped empty) Goggles, Striker, 12’ x 3/16” Hose - No Cylinders

Features: Solid Forged Head with Mixer Triangular Tube construction Brazed Connection Cutting Oxygen Valve features Ease-on and Easy Access Solid Brass Forged Lever Part Number

Model Number

Kit Contents

Tip Seat Style

Torch Handle

Torch Head Angle

Cutting Tip

Welding and Brazing Tip

Recommended Attachments

4403213

V-100601-200 DLX w/Cylinders

Goggles, Striker, 12' x 3/16" Hose, 20 CU. FT. OXY. CYL., 10 CU. FT. "MC" ACET. CYL. (cylinders shipped empty)

V3-101

V-100C

90°

V3-101-1

23A90-3

4301650 - 88-5FBT R&L FBA, 4301651 - 88-5FBR R&L

Part Number

Fuel Gas

Certifications

Mixer

Cutting Attachment

Inlet

Mixing System

Fuel Regulator

Oxygen Regulator

4403213

Oxy-acetylene/Hydrogen

UL CGA E-4

V-W-1

V-1350

CGA 200 & 540

E

601-15-200

601-80-540

Model 601 Model 601

Description: Single Stage Compact Regulator This single stage regulator was designed to be compact, inexpensive, but with features available in more expensive regulators. It is used where cost and size are factors.

Compact Economical One-piece encapsulated seat design with internal filter and PTFE Teflon® seat 1-year warranty Featured in Expert Series outfits

Capacity

Stage

Gauges

Gas

Inlet

Outlet

3000295

601-15-200

Light Duty

Single

Acetylene

CGA 200

B 9/16" - 18 (M) LH

Certific ations CGA E-4

3000407

601-15-200

Light Duty

Single

Acetylene

CGA 200

A 3/8" - 24 (M)

CGA E-4

3000408

601-15-520

Light Duty

Single

Acetylene

CGA 520

A 3/8" (M) LH

CGA E-4

3000411

601-15-520

Light Duty

Single

Acetylene

CGA 520

B 9/16" - 18 (M) LH

CGA E-4

3000296

601-80-540

Light Duty

Single

Oxygen

CGA 540

B 3/8" - 18 (M) RH

CGA E-4

3000412

601-15-540A

Light Duty

Single

Oxygen

CGA 540

B 3/8" - 18 (M) RH

CGA E-4

3000409

601-50-510P

Light Duty

Single

500mm ABS Plastic 500mm ABS Plastic 500mm ABS Plastic 500mm ABS Plastic 500mm ABS Plastic 500mm ABS Plastic 500mm ABS Plastic

Propane

CGA 510P

B 9/16" - 18 (M) LH

CGA E-4

Part Number Model Number