Shp-dp920 728 Manual 4mk3n
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report 3i3n4
Overview 26281t
& View Shp-dp920 728 Manual as PDF for free.
More details 6y5l6z
- Words: 5,905
- Pages: 15
Safety Cautions
Outer Body Parts Number Pad Unlighted
This section contains important information to ensure the ’s safety and prevent potential damage to property. Please, read this section carefully and use the product accordingly.
Warning
Touch Number Pad
Number Pad Lighted
Fingerprint Reading Open Fingerprint Cover Button
BIOMETRICS
SHP-DP728
BIOMETRICS BIOMETRICS
BIOMETRICS
• The shall not install or repair the product without authorization. • Do not install the product in the place where the gap between the door and the frame is 5mm or more. • Make sure that no unauthorized person has the access to the . • Do not operate the product with wet hands, and keep liquids such as water or drinks away from the product, or the product may malfunction or be damaged. • Do not use the excessive force or sharp objects to push the lockbuttons, as this can damage the product. • Make sure that the door is completely closed when going outside. The manufacturer does not assume the responsibility for any harm caused by engagement of the lock on an improperly closed door.
64&3."/6"-
BIOMETRICS
Convenient Opening
Easy push/pull handle access
Welcome Function
When a gets close to the door lock, the authorization standby mode will automatically activate.
• Please do not hang on the product or pull it. • Long-term exposure to direct sunlight may cause a crack on its touch pad. Avoid exposure to direct sunlight during installation. • During battery replacement, use a new one instead of the existing battery. • Be sure to correctly match the poles (+/-) when installing the batteries. Install the batteries with the correct poles (+/-). • Do not use water, benzene or alcohol when cleaning the product, as these fluids can cause product malfunction. • Replace the batteries within 1 week after the battery replacement alarm sounds. • Interference in wireless communication may occur when this product is used. • According to the wireless communication environment, its battery may consume much.
Card Reader
Proximity Sensor Number Pad Entry Complete/ Silent Mode Switch Button Battery Replacement Time Alert
BIOMETRICS
Away Security Setup
BIOMETRICS
Emergency Alert Light Double Lock Light External Power Part Reset Switch Emergency Keyhole
Inner Body Parts
Product Components
Silent-Mode Function
When going in or out, the sound of the key entering and door opening will be suspended.
The Battery Cover Release Button
The product components used may vary depending on the installation environment.
(After pressing the battery cover release button, pull towards the front, and then the battery cover will open.)
Automatic Card Reading Function
When a card touches the reader, the reader will conveniently recognize the card.
Battery Cover
BIOMETRICS
1.5V AA Batteries
Double Authorization
Requires & fingerprint combination to open
Security Assurance Function
Sound Control Switch
Mortise Mortise
When someone is inside the house, authorization for entry from the outside will be prohibited.
Strike
(SHS-AML320)
Built-in Wireless Module (Optional) Auto/Manual Locking Switch
Registration Button CLOSE Button
Built-in Fire Detection
Generates alarm in case of a fire
Security Function
Prevents intrusion from the outside
Smartphone Interworking functionG
Outer Body
Conveniently open the door through the Bluetooth function of a smart phone
Mortise Strike (SHS-AML220) box
Strike (For B2C Only)
Key Tag (For B2C Only) (2EA) Manual, Product Warranty ‘AA’ Batteries (LR6) Emergency Key
www.samsungsds-nss.com/en
Mortise
Strike Strike box
Inner Body
Handle Shaft Spring Handle Shaft, Installation Screws Installation Manual(For B2C Only)
Deadbolt Latch bolt Open-door sensor
GC68-02163A ED:02
2
SHS-AML320
SHS-AML220
Opening the Door from Outside with a
Opening the Door from the Inside
Fingerprint, Card and Key Tag Registration
When purchased, the product is set to Multi-leveled Security Code Entry Mode initially. Please refer to “Multi-leveled Security Code Entry Mode setting” for Common Mode setting. ※S ilent Mode
Available in both a push-pull or pull-push Depending on the direction of the door installed in the residence, customer can choose from either push-pull type or pull-push type on purchase.
You can and use up to 100 fingerprints. Up to 20 cards, including the key tag, can be ed. (Only ISO14443 A Type is available.) 1. Pressing the [] Button 2. Entering the (from the inside) (from the outside)
Push
Pull
Pull
Push
Before entering the , press the [] button and enter the , then both the sound of the key entering and the door opening will be suspended. It is a useful function if you do not want to disturb neighbors when you go in and out at night.
When two arbitrary buttons are lighted, press the buttons in order.
When the numbers on the number pad are lighted, enter the and press the [] button.
- If the security mode is changed as ‘common mode’, second step will be skipped. ● must be entered after the light is on, and if does not, touch [Number Pad] and re-enter. ● To cancel, press [ ] button and re-enter. ● If the is wrong 5 times, “peep” warning alarm will sound 20 times and the system will shut-down for about 3 minutes. When malfunction happens, “beep” will sound every 10 seconds, and stop mode will be turned off automatically after 3 minutes with multiple ‘beeps’.
Note
Open the battery cover of the inner body and briefly press the [] button.
Closing the Door from the Inside Automatic Locking Setting Manual Locking Setting
Note
Open the door from the outside using the fingerprint authentication system. Touch the sensor properly with the fingerprint part of your finger which has been ed. 1. Pressing [Open Fingerprint Cover] Button
3. Reading the Fingerprint to Be ed
The door is locked when the [Close] button is pressed.
Success: DING DONG DENG DONG Fail: DING DONG DING DONG
BIOMETRICS
Press the [Open Fingerprint Cover] button and the lid of the Fingerprint Reading opens.
Press and hold the [] button for 5 seconds.
Touch the Fingerprint Reading with the ed fingerprint after LED light turns on, the lid of the closes in approximately a second later. Then push the door handle to open the door.
Opening the Door from Outside with a Card or Key Tag
[Card and Key Tag Registration] 3. Placing the Card or Key Tag on the Card Reader (from the outside)
Success: DING DONG DENG Fail: DING DONG DING DONG When the number pad is lighted, enter ‘4560852580’ and then press the [] button.
CARD
Place the card or key tag to be ed on the card reader of the outer body. You will know the card or key tag has been ed when “DING DONG DENG” sounds.
Place the ed card or key tag to the card reader on the outer body.
● To multiple cards or key tags, lightly place another card or key tag to the card reader within 20 seconds after ing the previous card or key tag. Warning
Pairing of a smart phone Up to eight compatible smart phones can be paired. To pair multiple smart phones, turn off the Bluetooth of a paired smart phone, and pair another smart phone. If a Bluetooth smart phone ed is lost, replaced, or repaired and its information cannot be deleted from the door lock, the door lock should be initialized.
DING DONG
RD
RD CA RD CA
CA
Placing the Card or Key Tag on the Card Reader
RD
CA
4
4. Confirming Card or Key Tag Registration (from the outside)
DING DONG DENG
CARD
DING DONG DENG [11] button: Activate the Bluetooth mode. [00] button: Deactivate the Bluetooth mode.
Place the card or key tag on the card reader. The door will be opened after 1 second.
To end the registration, please press the [Registration] button on the inner body.
After the Bluetooth mode is activated, accessing the door lock from the outside or touching its number pad can authenticate the ed Bluetooth smartphone to open the door. The Bluetooth mode is activated by default.
The door can be opened from outside using a card or key tag. Place the ed card or key tag on the card reader.
BIOMETRICS
DING DONG DENG
Activation/Deactivation of the Bluetooth Mode
BIOMETRICS BIOMETRICS
Success: DING DONG DENG DONG Fail: DING DONG DING DONG
When LED light on the Fingerprint Reading is on, touch the with the fingerprint to be ed. When a “ding” sound is heard and LED light goes off, then remove the finger. (Must do it 3 times)
All ed data (, Fingerprint, Bluetooth, card, key tag) are deleted. After initialization, the is set to ‘1234’, and the ed card, key tag data are erased. Please a new after initialization. 1. Pressing the [] Button 2. Entering the Numbers for (from the inside) Initialization (from the outside) DING DONG DING DING DING DING DING DING
4. Exiting Fingerprint Registration Mode
Success: DING DONG DENG Fail: DING DONG DING DONG
DING
● To check if the door is locked from the inside, press the security button briefly; the red LED will flash if the door is locked and the blue LED will blink if the door is unlocked. ● For 5 seconds after the door is closed, the Bluetooth authentication mode is not turned on even though you approach the door lock. (Note that the Bluetooth mode is turned on when you touch the number pad.)
Initialization (, Fingerprint, Bluetooth, Card, Key Tag)
2. Reading Fingerprint
Enter the (‘1234’ after initialization) when the number pad is lighted, and press the [] button.
[Fingerprint Registration]
The door is automatically locked 1 seconds after the door is closed.
GC68-02162A ED01
Opening the Door from the Outside with a Fingerprint
BIOMETRICS
● Please be careful not to trap your Warning hand during use.
Or Success: DING DONG DENG DONG Fail: DING DONG DING DONG
Touching [Number Pad] will light up the number pad.
DING DONG DENG, DING DING
DING DONG
Multi-leveled Security Code Entry Mode
3
Open the battery cover, and press the [] button shortly.
Note
Press the [11] or [00] button and the [] button to activate or deactivate the Bluetooth mode.
● For the information on the pair/unfair of a Bluetooth smart phone, see the description of application use. ●Only smart phones with iOS 7.1 or higher and Android 4.3 or higher this function. Whether to Bluetooth, see the App description.
DING DONG
“sHome Doorlock” from App Store.
Turn on the BlueOpen the battery If the number pad tooth smart phone. cover and press the lights, enter ‘88’ and [REG] button shortly. press the [] button.
Success: DING DONG DENG DING DONG Fail: DING DONG DING DONG
5
DING DONG
Enter the and press the [] button.
Success: DING DONG DENG Fail: DING DONG DING DONG
Enter the 6-digit paring code displayed in the App of the phone, and press the [] button.
The smart phone is paired.
6
Deleting ed Fingerprints & Cards
Double Authorization Mode Setting
Set up Instructions for Alarm and Anti unlock functions
You can delete individual or all ed fingerprints and cards. 1. Pressing the [] Button 2. Entering the Current (from the inside) (from the outside)
You can delete Double authorization mode requires both fingerprint and to open the door, ensuring more security. To setup the double authorization mode, one or more fingerprints must be ed.
Alarm function When this function is activated, an alarm sound and light will turn on for approximately 5 minutes duration.
DING DONG DING DING
DING DONG DENG DING DONG DENG
DING DONG
Open the battery cover of the inner body and briefly press the [] button for 3 seconds.
Enter the current when the number pad is lighted, and press [] button.
[Deleting Fingerprints] 3. Reading the Fingerprint to Be Deleted
4. Exiting Fingerprint Deletion Mode
Success: DING DONG DENG Fail: DING DONG DING DONG
DING
When LED light on the Fingerprint Reading is on, touch the with the fingerprint to be deleted.
[Deleting All Fingerprints] 3. Entering the number (from the outside)
[4] Button : Double authorization mode on [6] Button : Double authorization mode off
Briefly press the [] button on the inner body.
Anti-By function When this function is activated, the internal handle will become tightened to prevent by attempts through door edge tools will be minimized. Set up the Alarm function
Press the [] button after pressing the [4] or [6] button, and the authorization mode will be set.
Set up the Anti-Unlock function
DING DONG DENG
DING DONG DENG
Two-factor Authentication Mode Operation DING DONG DENG
To end the deletion mode, press [Registration] button.
[Deleting All Cards] 3. Entering the number (from the outside)
DING DONG DENG
Success: DING DONG DENG DONG Fail: DING DONG DING DONG
Success: DING DONG DENG Fail: DING DONG DING DONG
Touching [Number Pad].
Enter the when the number pad is lighted, and press the [] button.
Touch a ed fingerprint on the Fingerprint Reading . After a successful authentication, the door opens.
When the door is closed, can set up the alarm function by pressing and holding the [ ] button for 3 seconds until sound confirmation.
Press [] and hold. After 3 seconds, the alarm will be come active.
Release the Alarm function
Release the Anti-By function
BEEP BEEP BEEP~
Or
DING DONG DENG
Change The can be 4~12 digits number. Only one can be ed. If you want to delete all fingerprints, press [77] + [] after step2.
If you want to delete all cards, press [88] + [] after step 2.
1. Pressing the [] Button (from the inside)
Security Assurance Mode Activation/Deactivation
2. Entering the Current (from the outside) DING DONG DENG, DING DING
DING DONG
At-home security mode is to prevent opening of the door from outside while someone is inside. Security Assurance Mode Activation
● Anti-By function should only be set up when there is no one inside.
DING DONG DENG DONG
While the door is locked, press [CLOSE] button on the inner body part for 3 seconds.
Pull the inner body handle to open the door, and it will deactivate.
Open the battery cover of the inner body and briefly press the [] button.
Enter the current (‘1234’ after initialization) when the number pad is lighted, and press the [] button.
3. Entering a New (from the outside)
4. Checking New Operation (from the outside)
DING DING DENG
DING DONG DENG DONG
Sound Setting and Releasing The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unlocked, can be set according to the ’s preference. The product is set to generate all sounds at the factory. Open the battery cover on the inner body.
Security Assurance Mode Operation Or
Rapid beeping
Press the [CLOSE] button to release the internal handle from Anti-By function. When this function is active, it may be harder to pull the internal handle for elderly or children to open the door from inside.
Warning
Security Assurance Mode Deactivation
DING DONG DENG
After touching the Number Pad, have a ed fingerprint read, or a ed card, or enter the and then press the [] button.
Inside: Press the [CLOSE] button, then the sound for action-unavailable willbe heard. Outside: Press the [Number Pad] or touch with a card, then the sound for action-unavailable will be heard.
●W hen the security assurance function is activated, the door cannot be unlocked from the outside, so please be careful. Be especially careful not to allow children to set this mode accidently from the inside. Warning
Enter the new (4 to 12 digits) and press the [] button.
To make sure the has been properly ed, check the new and close the door.
●M anage your with care so that unauthorized people will not have access to it. Regularly changing your can reduce the risk of it being leaked. Warning
7
Put the [Sound Control] switch on one of [0], [1], or [2], and close the battery cover.
- [ 0 ] Button: All sounds except the alarm sound are deactivated. - [1] and [2] Buttons: All sounds are activated and the sounds get bigger as the step become higher.
8
9
Welcome Function On/Off
Automatic/Manual Locking Setting
Alarm Sound (Prank Prevention Function)
The welcome function is a convenient function that automatically activates the authorization standby mode when a approaches the door, even before touching the number pad.
The Automatic Locking mode allows for automatic locking of the door when it is closed.
This function generates an alarm sound and deactivates lock operation when it is improperly handled from the outside.
DING DONG
Open the battery cover and press [Registration] button briefly.
On and Off / Function Description
Open the battery cover on the inner body.
DING DONG DENG
[1]+[] button: Welcome function on, the oneminute alarm function on [2]+[] button: Welcome function on, the oneminute alarm function off [3]+[] button: Welcome function off [5]+[] button: Set up fingerprint Authentication standby mode [8]+[] button: Clear Fingerprint Authentication standby mode
- Welcome function on: The mode will automatically activate the authorization standby mode when a approaches the door lock. - Welcome function off: The mode will authorize a when the enters the on the number pad or connects a card to the number pad. - One-minute alarm function on/ off: When someone remains in front of the door lock for more than a minute, this mode will sound the tamper prevention alarm.
Caution
- Automatic: The door is automatically locked 1 seconds after being closed. - Manual: The door does not lock automatically, and [CLOSE] button must be pressed from the inside, touch [Number Pad] to close the door.
Intrusion Detection Function This function generates the alarm sound when an attempt is made to forcefully open the door from the inside or the outside. (This is a basic function of the lock, and cannot be separately set or released.) If the door is forcefully opened while locked, the door opening sensor detects it and generates the alarm sound.
Battery Replacement Alarm Generation
Replacing the Battery Replace all 8 batteries within a 1 week of the first alarm sound. - The unit will stop operating suddenly if the batteries are not replaced.
DING DONG DENG [7] Button : Multi-leveled Security Code Entry Mode [9] Button : Common Mode
Briefly press the [] button on the inner body.
Press the [] button after pressing the [7] or [9] button, and the security mode will be set.
Door Lock Time Setup Function This function sets the time interval between the moment the door open/closed sensor recognizes the door as closed and the moment deadbolt locks the door. In an environment that the door closes slowly and the deadbolt jams before the door is fully closed, the situation can be fixed by adjusting the door lock time. DING DONG
Default: 1 second [51] : 1 second
Press [51] ~ [59] button, and then press [] button.
10
Press the [] button.
Outside
Apply the ed card or key tag to the card reader, or enter the and then press the [] button.
Built-in Fire Detection Function This function generates the alarm sound when fire is detected so that the residence can quickly respond. The built-in fire detection function is a basic function of the lock, and cannot be released by the . Fire detection function is operational at about 70 °C ± 10 °C; this can vary depending on the installation environment.
Product Specifications Item Voltage
Using the Emergency Battery
Operation Method
Electronic Control Method (, Fingerprint, Bluetooth, Card, Key Tag)
Product Dimensions
Purchase an emergency battery (9V) at the nearest store. - As the alkaline batteries offer longer life, they are recommended over the manganese batteries or rechargeable ones.
11
AA Alkaline 1.5 Batteries (LR6) 4EA or 8EA (6V) 9V Battery (6LF22) (Separately sold)
Weight
Opening the Door Using an Emergency Battery
Specifications
Emergency Power Source
If the batteries are not replaced after their replacement time comes, they will be completely discharged and the lock will not operate.
While connecting a 9V battery to the point, it is available to use fingerprint, card and .
[59] : 9 second
Open the battery cover of the inner body and briefly press the [] button.
● Depending on battery manufacturer, date of manufacture and the environment, the duration of use may vary. (In the case of average use, given as 10 times a day, 8 AA alkaline 1.5Vbatteries can last for 10 months.) ● If the poles of the batteries are not placed properly, the lock will not operate normally. ● Liquid leaks from batteries can damage the product. Check the batteries regularly (every 6 months). ● After the battery replacement alarm has sounded, /card information cannot be ed, changed, deleted, initialized or configured until the batteries are replaced. ~
Warning
You can set the security mode suitable for your use when you open the door using a .
Inside
When fire occurs, the temperature sensor detects it and flashes the [Close] button while generating the alarm sound. The door is automatically opened after the alarm sound has stopped. (The lock resumes normal operation if the inside temperature returns to a normal level.) The built-in fire detection function is activated when the temperature rises around 60°C, which may differ depending on the installation environment.
If the melody of “Blues for Elise” sounds when opening the door with the or a card (key tag), it is time to replace the batteries. (The low battery indicator is lighted when the melody sounds.)
Multi-leveled Security Code Entry Mode
This alarm will sound if an attempt is made to open the door with an invalid card, or if a wrong is entered five times in a row. The alarm sound is generated, and the lock is deactivated for 3 minutes. While the door is in this inactive mode, a single “DING” sound is generated every 10 seconds and seven consecutive “DINGS” will sound after 3 minutes. Following this, the lock is released from inactive mode.)
Releasing the Alarm
Replacing the Batteries
●The factory defaults are set with the welcome function on and the alarm function off. ● The working distance of the infrared sensor can differ depending on light conditions and other environments. When the front door is exposed to sun light or constant bright lights it is advised to limit the usage of the sensor as it might sound the alarm.
DING DONG
Set the [Automatic/Manual Locking] toggle switch of the Inner Body to the ‘A’/‘M’ position.
4.1 kg (including both inner and outer bodies) Outer Body (including the handle)
87.5mm(W) X 391.8mm(H) X 64.5mm(D)
Inner Body (including the handle)
88.5mm (W) X 357.6mm(H) X 69.3mm(D)
● T he contents of this guide are subject to change without prior notice to the in order to enhance performance of the product.
12
SHP-DP920 Samsung SDS Door Lock and Reference Guide
Ver1.0.0
Product Specifications Item
Spec.
Exterior Unit
87.5mm(W)×391.8mm(H)×64.5mm(D)
Interior Unit
88.5mm(W)×357.6mm(H)×69.3mm(D)
Size Voltage Emergency Power Source Battery Life Card Standard
Exterior Parts
4 AA Alkaline 1.5V Batteries (LR6) (6V) 9V Battery(6LF22)
(Separately sold)
10 Months (based on an average of 6 uses per day) ISO14443A (Mifare® )
Interior Parts
Mortise
The Samsung SDS Z-Wave Door Lock is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enable Z-Wave Plus products. The Samsung SDS Z-Wave Door Lock must be used in conjunction with a Security Enabled Z-Wave Controller in other to fully utilize all implemented functions. The Samsung SDS Z-Wave Door Lock can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Z-Wave Specifications
Device Type
:
Door Lock – Keypad (SPECIFIC_TYPE_SECURE_KEYPAD_DOOR_LOCK)
Role Type
:
LSS (Listening Sleeping Slave)
Command Class /Control
Mandatory CC :
Z-Wave plus info (MUST be place first in NIF) – (V2)
Manufacturer Specific (V2)
Security (V1)
Device Reset Locally (V1)
Battery (V1)
Power Level (V1)
Version (V2)
Door Lock (V2)
Code (V1)
Association (V2)
Association Group Information (V1)
Recommended CC
Notification (V4)
Configuration (V1)
Firmware update meta data (V2)
Schedule Entry Lock (V3)
Time Parameters (V1)
Time (V2)
Z-Wave plus info (V2) -
Z-Wave Plus Version : 02
-
Role Type : LSS (Listening Sleeping Slave)
-
Node Type : Z-Wave Plus Node
Manufacturer Specific (V2) -
Device ID Type : 01(Serial Number)
-
Device ID Data Format : 01 (Binary)
-
Device ID Data Length Indicator : 16
-
Device ID : XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX
Version (V2) -
Z-Wave Protocol Library Type : 03
-
Z-Wave Protocol Version : 04
-
Z-Wave Protocol Sub Version : 05
-
Firmware 0 Version : 01
-
Firmware 0 Sub Version : 03
-
Hardware Version : 01
Door Lock (V2) -
Unsecure(0x00), Secure(0xFF) Note : When using ‘Operation_Set’ command, lock will execute ‘Unsecure(0x00)’ then perform ‘Auto Re-lock’ if door is not open. When using ‘Operation_Get’ command, lock ‘Operation_Set’ command. (take about 2 seconds)
can
response
after
executing
Code (V1) -
Lock will accept maximum 130 pin codes that are 4-10 digits in length. ① ed s : 130 ② Type : Number, Card (Key Tag), Fingerprint, Bluetooth ⋅ Card (Key Tag), Fingerprint, Bluetooth : Cannot be ed through Z-Wave ③ ID Range ⋅ Number : 1 ~ 130
⋅ Card (Key Tag) : 1 ~ 20 ⋅ Bluetooth : 21 ~ 30 ⋅ Fingerprint : 31 ~ 130
Association (V2) & Association Group Information (V1) -
Lifeline between controller and SHP-DP920
-
ed command classes : Battery report, Notification report, and Device Reset Locally notification
Maximum ed node is 1EA
Notification (V4) Notification Type
Event
Access Control
Manual Lock Operation (0x01)
(0x06)
Manual Unlock Operation (0x02)
Event Parameter
RF Lock Operation (0x03) RF Unlock Operation (0x04) Keypad Unlock Operation (0x06) RF Not Fully Locked Operation (0x08) Auto Lock Loced Operation (0x09) Auto Lock Not Fully Operation (0x0A) Lock Jammed (0x0B) All codes deleted (0x0C) Single code deleted (0x0D) New code added (0x0E) New code not added due to duplicate code (0x0F) New Program code Entered - Unique code for lock configuration (0x12) Home Security (0x07)
Intrusion, Unkown Location (0x02) Tampering, Invalid Code (0x04)
ID
Motion Detection, Unknown Location (0x08) Emergency
Police (0x01)
(0x0A)
Fire Service (0x02)
Configuration (V1)
Name
Parameter Number
Size
Value
Description
Security Function
0x01
1byte
0x00
Disable (Default)
0x01
Enable
0x02
System Disable
0x03
System Enable
0x04
Request for Enable
0x05
Fail
0x00
Disable (Default)
0x01
Enable
Privacy Mode
0x02
1byte
1)
1)
1)
1)
ed ID
0x03
1byte
1 ~130
The number of ed codes.
Platform
0x0A
1byte
0x00
Common (Default)
0x01
Samsung SDS
1)
2)
3)
This value can be used when the device is connected with platform of Samsung SDS. This function is not related to Z-Wave CC. - 0x02 : Command for disable which is set by platform of Samsung SDS. After setting, if you try to get value of Security Function , '0x00' will be reported. - 0x03 : Command for enable which is set by platform of Samsung SDS. After setting, if you try to get value of Security Function, '0x01' will be reported. - 0x04 : 'Request for Enable' command which is reported by Doorlock. This cannot be set. (8th function in manual) - 0x05 : If the request for 'Request for Enable' command is failed in platform, this will be set by platform of Samsung SDS.
Value of Security Function is not changed by this command. 2)
This parameter is ed to ‘Configuration Get Command’ only.
3)
This value set by platform after device connected with platform of Samsung SDS.
Firmware update meta data (V2) -
Manufacturer ID : 0x022E (Samsung SDS)
Schedule Entry Lock (V3) -
ed the Number of Slots Week Day : 0
-
ed the Number of Slots Year Day : 0
-
ed the Number of Slots Daily Repeating : 130
Glossary Devices and nodes are all to describe an individual Z-Wave device. These
Device or Node
Unsecure Unsecured
are all interchangeable when setting up your Z-Wave network /
Unlock / Unlocked
Secure / Secured
Lock / Locked
Inclusion
Add a Z-Wave device to the network
Exclusion
Delete a Z-Wave device from the network A collection of Z-Wave devices is controlled by primary and secondary controllers
Z-Wave Network
operating on the same system. A Z-Wave network has its own unique ID code so that controllers not in the network cannot control the system. Association is used to organize nodes in different groups allowing the device to
Association
identify the nodes by a group identifier. The groups can also be copied to other devices.
Note : Pressing the [REG] button is only available while the door is open. (Deadbolt must be unsecured.)
Basic Functions
1. Factory Reset All ed Master/ data will be deleted, and Master PIN Code is set to ‘1234’. Also ZWave Door Lock is being removed from a network. ①
Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
②
Press the [*] button after pressing the [4560852580] button. (Success : Ding dong dang, Fail : Ding dong Ding dong)
※ Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
2. Changing the Master PIN Code You can enter only one Master PIN Code. If changing the Master PIN code, All PIN Codes are deleted. ①
Press the [REG] button. (Ding dong)
②
Enter the new Master PIN Code, and press the [*] button.(4~12digits) (Ding dong dang)
3. ing a Card You can up to 20 Card. (Supproted ISO14443 A Type) To multiple cards, lightly place another card to the card reader within 20 seconds after ing the previous card. Also you can add card later after completing registration. ①
Press the [REG] button. (Ding dong)
②
Place the card to be ed on the card reader of the exterior body.(Ding dong dang)
③
Place the card on the card reader for the addtional registration or press the [REG] button to quit.
4. ing a Fingerprint You can up to 100 fingerprints. ①
Press the [REG] button. (Ding dong)
②
When LED light on the Fingerprint Reading is on, touch the with the fingerprint to be ed. When a “ding” sound is heard and LED light goes off, then remove the finger. (Must do it 3 times)
③
To end the registration, please press the [REG] button on the inner body.
5. ing a Bluetooth ①
Press the [REG] button. (Ding dong)
②
Enter the [88] + [*]
③
Enter the + [*] (Ding dong deng → Ding ding)
④
Check a pairing number from Smart Door Lock App of smartphone.
(Ding dong)
(First, please install the Smart Door Lock app in the smart phone.) ⑤
Enter a Pairing number + [*] (Ding dong deng)
6. Inclusion / Exclusion into(from) Z-Wave Network 6.1 Inclusion into Z-Wave Network ①
Click [Add] icon in Z-Wave PC Conroller Program.
②
Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
③
Press the [*] button after pressing the [00] button. (Success : Ding dong dang, Fail : Ding dong Ding dong)
6.2 Exclusion from Z-Wave Network After exclusion from Z-Wave Netwokr, it will no longer be remotely-controlled via the controller. ①
Click [Remove] icon in Z-Wave PC Conroller Program.
②
Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
③
Press the [*] button after pressing the [00] button.
(Success : Ding dong dang, Fail : Ding dong Ding dong)
7. Opening the Door with a PIN Code ①
Touch the [Touchscreen].
②
Enter the PIN Code and press the [*] button.
③
The door opens whithin one second.
8. Opening the Door with a Card ①
Place the Card on the Card Reader.
②
The door opens whithin one second.
9. Opening the Door with a Fingerprint ①
Press the [Open Fingerprint Cover] button and the lid of the Fingerprint Reading opens.
②
Touch the Fingerprint Reading with the ed fingerprint after LED light turns on, the lid of the closes in approximately a second later.
③
Then push the door handle to open the door.
10. Opening the Door with a Bluetooth ①
Access the door lock from the outside or touch its number pad.
②
The number pad will light up.
③
Push message is sent to smartphone through Bluetooth.
④
Press the icon of push message (from smartphone)
⑤
Then push the door handle to open the door.
Addtional Function
11. Activation/Deactivation of the Bluetooth Mode After the Bluetooth mode is activated, accessing the door lock from the outside or touching its number pad can authenticate the ed Bluetooth smartphone to open the door. The Bluetooth mode is activated by default. ①
Open the battery cover, and press the [REG] button shortly..
②
Press the [11] or [00] button and the [*] button to activate or deactivate the Bluetooth mode. [11] button: Activate the Bluetooth mode. [00] button: Deactivate the Bluetooth mode.
12. Privacy Mode Function Press and hold the [CLOSE] button for more than three seconds. (Ding dong dang) As it is set from the inside, provides a secure lock for the convenience of the occupant(s). When the privacy mode function is activated, the door cannot be unlocked(unsecured) from the outside, so please be careful.
13. Setting the Security Function This is a function to prevent any intrusion while you are out. Should the door be opend from the inside while the intrusion prevention function is on, the emergency alert light will flash and the alarm will make “beep beep beep~” sound. ①
When the door is closed [
②
Press the [
] of the exterior body’s number pad will light up.
] button on the exterior body within 3 seconds while the door is locked.
(Ding dong dang)
14. Lockout Mode When more than 5 failed authentication attempts with uned PIN Code/Cards occur, the alarm sound is generated, and the lock is deactivated for 3 minutes.
15. Intrusion Detection Function When the Interior Unit is forcibly detached while the door is locked, it is detected by the door open/close sensor, the alarm sounds. The Intrution Detection function is a basic function and cannot be disabled.
16. Sound Setting The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unloced, can be set according to the ’s preference. Put the [Sound Control] switch on one of [0], [1] or [2]. [0] : Mute
[1] : Normal
[2] : Loud
17. Addtional Function Mode
Outer Body Parts Number Pad Unlighted
This section contains important information to ensure the ’s safety and prevent potential damage to property. Please, read this section carefully and use the product accordingly.
Warning
Touch Number Pad
Number Pad Lighted
Fingerprint Reading Open Fingerprint Cover Button
BIOMETRICS
SHP-DP728
BIOMETRICS BIOMETRICS
BIOMETRICS
• The shall not install or repair the product without authorization. • Do not install the product in the place where the gap between the door and the frame is 5mm or more. • Make sure that no unauthorized person has the access to the . • Do not operate the product with wet hands, and keep liquids such as water or drinks away from the product, or the product may malfunction or be damaged. • Do not use the excessive force or sharp objects to push the lockbuttons, as this can damage the product. • Make sure that the door is completely closed when going outside. The manufacturer does not assume the responsibility for any harm caused by engagement of the lock on an improperly closed door.
64&3."/6"-
BIOMETRICS
Convenient Opening
Easy push/pull handle access
Welcome Function
When a gets close to the door lock, the authorization standby mode will automatically activate.
• Please do not hang on the product or pull it. • Long-term exposure to direct sunlight may cause a crack on its touch pad. Avoid exposure to direct sunlight during installation. • During battery replacement, use a new one instead of the existing battery. • Be sure to correctly match the poles (+/-) when installing the batteries. Install the batteries with the correct poles (+/-). • Do not use water, benzene or alcohol when cleaning the product, as these fluids can cause product malfunction. • Replace the batteries within 1 week after the battery replacement alarm sounds. • Interference in wireless communication may occur when this product is used. • According to the wireless communication environment, its battery may consume much.
Card Reader
Proximity Sensor Number Pad Entry Complete/ Silent Mode Switch Button Battery Replacement Time Alert
BIOMETRICS
Away Security Setup
BIOMETRICS
Emergency Alert Light Double Lock Light External Power Part Reset Switch Emergency Keyhole
Inner Body Parts
Product Components
Silent-Mode Function
When going in or out, the sound of the key entering and door opening will be suspended.
The Battery Cover Release Button
The product components used may vary depending on the installation environment.
(After pressing the battery cover release button, pull towards the front, and then the battery cover will open.)
Automatic Card Reading Function
When a card touches the reader, the reader will conveniently recognize the card.
Battery Cover
BIOMETRICS
1.5V AA Batteries
Double Authorization
Requires & fingerprint combination to open
Security Assurance Function
Sound Control Switch
Mortise Mortise
When someone is inside the house, authorization for entry from the outside will be prohibited.
Strike
(SHS-AML320)
Built-in Wireless Module (Optional) Auto/Manual Locking Switch
Registration Button CLOSE Button
Built-in Fire Detection
Generates alarm in case of a fire
Security Function
Prevents intrusion from the outside
Smartphone Interworking functionG
Outer Body
Conveniently open the door through the Bluetooth function of a smart phone
Mortise Strike (SHS-AML220) box
Strike (For B2C Only)
Key Tag (For B2C Only) (2EA) Manual, Product Warranty ‘AA’ Batteries (LR6) Emergency Key
www.samsungsds-nss.com/en
Mortise
Strike Strike box
Inner Body
Handle Shaft Spring Handle Shaft, Installation Screws Installation Manual(For B2C Only)
Deadbolt Latch bolt Open-door sensor
GC68-02163A ED:02
2
SHS-AML320
SHS-AML220
Opening the Door from Outside with a
Opening the Door from the Inside
Fingerprint, Card and Key Tag Registration
When purchased, the product is set to Multi-leveled Security Code Entry Mode initially. Please refer to “Multi-leveled Security Code Entry Mode setting” for Common Mode setting. ※S ilent Mode
Available in both a push-pull or pull-push Depending on the direction of the door installed in the residence, customer can choose from either push-pull type or pull-push type on purchase.
You can and use up to 100 fingerprints. Up to 20 cards, including the key tag, can be ed. (Only ISO14443 A Type is available.) 1. Pressing the [] Button 2. Entering the (from the inside) (from the outside)
Push
Pull
Pull
Push
Before entering the , press the [] button and enter the , then both the sound of the key entering and the door opening will be suspended. It is a useful function if you do not want to disturb neighbors when you go in and out at night.
When two arbitrary buttons are lighted, press the buttons in order.
When the numbers on the number pad are lighted, enter the and press the [] button.
- If the security mode is changed as ‘common mode’, second step will be skipped. ● must be entered after the light is on, and if does not, touch [Number Pad] and re-enter. ● To cancel, press [ ] button and re-enter. ● If the is wrong 5 times, “peep” warning alarm will sound 20 times and the system will shut-down for about 3 minutes. When malfunction happens, “beep” will sound every 10 seconds, and stop mode will be turned off automatically after 3 minutes with multiple ‘beeps’.
Note
Open the battery cover of the inner body and briefly press the [] button.
Closing the Door from the Inside Automatic Locking Setting Manual Locking Setting
Note
Open the door from the outside using the fingerprint authentication system. Touch the sensor properly with the fingerprint part of your finger which has been ed. 1. Pressing [Open Fingerprint Cover] Button
3. Reading the Fingerprint to Be ed
The door is locked when the [Close] button is pressed.
Success: DING DONG DENG DONG Fail: DING DONG DING DONG
BIOMETRICS
Press the [Open Fingerprint Cover] button and the lid of the Fingerprint Reading opens.
Press and hold the [] button for 5 seconds.
Touch the Fingerprint Reading with the ed fingerprint after LED light turns on, the lid of the closes in approximately a second later. Then push the door handle to open the door.
Opening the Door from Outside with a Card or Key Tag
[Card and Key Tag Registration] 3. Placing the Card or Key Tag on the Card Reader (from the outside)
Success: DING DONG DENG Fail: DING DONG DING DONG When the number pad is lighted, enter ‘4560852580’ and then press the [] button.
CARD
Place the card or key tag to be ed on the card reader of the outer body. You will know the card or key tag has been ed when “DING DONG DENG” sounds.
Place the ed card or key tag to the card reader on the outer body.
● To multiple cards or key tags, lightly place another card or key tag to the card reader within 20 seconds after ing the previous card or key tag. Warning
Pairing of a smart phone Up to eight compatible smart phones can be paired. To pair multiple smart phones, turn off the Bluetooth of a paired smart phone, and pair another smart phone. If a Bluetooth smart phone ed is lost, replaced, or repaired and its information cannot be deleted from the door lock, the door lock should be initialized.
DING DONG
RD
RD CA RD CA
CA
Placing the Card or Key Tag on the Card Reader
RD
CA
4
4. Confirming Card or Key Tag Registration (from the outside)
DING DONG DENG
CARD
DING DONG DENG [11] button: Activate the Bluetooth mode. [00] button: Deactivate the Bluetooth mode.
Place the card or key tag on the card reader. The door will be opened after 1 second.
To end the registration, please press the [Registration] button on the inner body.
After the Bluetooth mode is activated, accessing the door lock from the outside or touching its number pad can authenticate the ed Bluetooth smartphone to open the door. The Bluetooth mode is activated by default.
The door can be opened from outside using a card or key tag. Place the ed card or key tag on the card reader.
BIOMETRICS
DING DONG DENG
Activation/Deactivation of the Bluetooth Mode
BIOMETRICS BIOMETRICS
Success: DING DONG DENG DONG Fail: DING DONG DING DONG
When LED light on the Fingerprint Reading is on, touch the with the fingerprint to be ed. When a “ding” sound is heard and LED light goes off, then remove the finger. (Must do it 3 times)
All ed data (, Fingerprint, Bluetooth, card, key tag) are deleted. After initialization, the is set to ‘1234’, and the ed card, key tag data are erased. Please a new after initialization. 1. Pressing the [] Button 2. Entering the Numbers for (from the inside) Initialization (from the outside) DING DONG DING DING DING DING DING DING
4. Exiting Fingerprint Registration Mode
Success: DING DONG DENG Fail: DING DONG DING DONG
DING
● To check if the door is locked from the inside, press the security button briefly; the red LED will flash if the door is locked and the blue LED will blink if the door is unlocked. ● For 5 seconds after the door is closed, the Bluetooth authentication mode is not turned on even though you approach the door lock. (Note that the Bluetooth mode is turned on when you touch the number pad.)
Initialization (, Fingerprint, Bluetooth, Card, Key Tag)
2. Reading Fingerprint
Enter the (‘1234’ after initialization) when the number pad is lighted, and press the [] button.
[Fingerprint Registration]
The door is automatically locked 1 seconds after the door is closed.
GC68-02162A ED01
Opening the Door from the Outside with a Fingerprint
BIOMETRICS
● Please be careful not to trap your Warning hand during use.
Or Success: DING DONG DENG DONG Fail: DING DONG DING DONG
Touching [Number Pad] will light up the number pad.
DING DONG DENG, DING DING
DING DONG
Multi-leveled Security Code Entry Mode
3
Open the battery cover, and press the [] button shortly.
Note
Press the [11] or [00] button and the [] button to activate or deactivate the Bluetooth mode.
● For the information on the pair/unfair of a Bluetooth smart phone, see the description of application use. ●Only smart phones with iOS 7.1 or higher and Android 4.3 or higher this function. Whether to Bluetooth, see the App description.
DING DONG
“sHome Doorlock” from App Store.
Turn on the BlueOpen the battery If the number pad tooth smart phone. cover and press the lights, enter ‘88’ and [REG] button shortly. press the [] button.
Success: DING DONG DENG DING DONG Fail: DING DONG DING DONG
5
DING DONG
Enter the and press the [] button.
Success: DING DONG DENG Fail: DING DONG DING DONG
Enter the 6-digit paring code displayed in the App of the phone, and press the [] button.
The smart phone is paired.
6
Deleting ed Fingerprints & Cards
Double Authorization Mode Setting
Set up Instructions for Alarm and Anti unlock functions
You can delete individual or all ed fingerprints and cards. 1. Pressing the [] Button 2. Entering the Current (from the inside) (from the outside)
You can delete Double authorization mode requires both fingerprint and to open the door, ensuring more security. To setup the double authorization mode, one or more fingerprints must be ed.
Alarm function When this function is activated, an alarm sound and light will turn on for approximately 5 minutes duration.
DING DONG DING DING
DING DONG DENG DING DONG DENG
DING DONG
Open the battery cover of the inner body and briefly press the [] button for 3 seconds.
Enter the current when the number pad is lighted, and press [] button.
[Deleting Fingerprints] 3. Reading the Fingerprint to Be Deleted
4. Exiting Fingerprint Deletion Mode
Success: DING DONG DENG Fail: DING DONG DING DONG
DING
When LED light on the Fingerprint Reading is on, touch the with the fingerprint to be deleted.
[Deleting All Fingerprints] 3. Entering the number (from the outside)
[4] Button : Double authorization mode on [6] Button : Double authorization mode off
Briefly press the [] button on the inner body.
Anti-By function When this function is activated, the internal handle will become tightened to prevent by attempts through door edge tools will be minimized. Set up the Alarm function
Press the [] button after pressing the [4] or [6] button, and the authorization mode will be set.
Set up the Anti-Unlock function
DING DONG DENG
DING DONG DENG
Two-factor Authentication Mode Operation DING DONG DENG
To end the deletion mode, press [Registration] button.
[Deleting All Cards] 3. Entering the number (from the outside)
DING DONG DENG
Success: DING DONG DENG DONG Fail: DING DONG DING DONG
Success: DING DONG DENG Fail: DING DONG DING DONG
Touching [Number Pad].
Enter the when the number pad is lighted, and press the [] button.
Touch a ed fingerprint on the Fingerprint Reading . After a successful authentication, the door opens.
When the door is closed, can set up the alarm function by pressing and holding the [ ] button for 3 seconds until sound confirmation.
Press [] and hold. After 3 seconds, the alarm will be come active.
Release the Alarm function
Release the Anti-By function
BEEP BEEP BEEP~
Or
DING DONG DENG
Change The can be 4~12 digits number. Only one can be ed. If you want to delete all fingerprints, press [77] + [] after step2.
If you want to delete all cards, press [88] + [] after step 2.
1. Pressing the [] Button (from the inside)
Security Assurance Mode Activation/Deactivation
2. Entering the Current (from the outside) DING DONG DENG, DING DING
DING DONG
At-home security mode is to prevent opening of the door from outside while someone is inside. Security Assurance Mode Activation
● Anti-By function should only be set up when there is no one inside.
DING DONG DENG DONG
While the door is locked, press [CLOSE] button on the inner body part for 3 seconds.
Pull the inner body handle to open the door, and it will deactivate.
Open the battery cover of the inner body and briefly press the [] button.
Enter the current (‘1234’ after initialization) when the number pad is lighted, and press the [] button.
3. Entering a New (from the outside)
4. Checking New Operation (from the outside)
DING DING DENG
DING DONG DENG DONG
Sound Setting and Releasing The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unlocked, can be set according to the ’s preference. The product is set to generate all sounds at the factory. Open the battery cover on the inner body.
Security Assurance Mode Operation Or
Rapid beeping
Press the [CLOSE] button to release the internal handle from Anti-By function. When this function is active, it may be harder to pull the internal handle for elderly or children to open the door from inside.
Warning
Security Assurance Mode Deactivation
DING DONG DENG
After touching the Number Pad, have a ed fingerprint read, or a ed card, or enter the and then press the [] button.
Inside: Press the [CLOSE] button, then the sound for action-unavailable willbe heard. Outside: Press the [Number Pad] or touch with a card, then the sound for action-unavailable will be heard.
●W hen the security assurance function is activated, the door cannot be unlocked from the outside, so please be careful. Be especially careful not to allow children to set this mode accidently from the inside. Warning
Enter the new (4 to 12 digits) and press the [] button.
To make sure the has been properly ed, check the new and close the door.
●M anage your with care so that unauthorized people will not have access to it. Regularly changing your can reduce the risk of it being leaked. Warning
7
Put the [Sound Control] switch on one of [0], [1], or [2], and close the battery cover.
- [ 0 ] Button: All sounds except the alarm sound are deactivated. - [1] and [2] Buttons: All sounds are activated and the sounds get bigger as the step become higher.
8
9
Welcome Function On/Off
Automatic/Manual Locking Setting
Alarm Sound (Prank Prevention Function)
The welcome function is a convenient function that automatically activates the authorization standby mode when a approaches the door, even before touching the number pad.
The Automatic Locking mode allows for automatic locking of the door when it is closed.
This function generates an alarm sound and deactivates lock operation when it is improperly handled from the outside.
DING DONG
Open the battery cover and press [Registration] button briefly.
On and Off / Function Description
Open the battery cover on the inner body.
DING DONG DENG
[1]+[] button: Welcome function on, the oneminute alarm function on [2]+[] button: Welcome function on, the oneminute alarm function off [3]+[] button: Welcome function off [5]+[] button: Set up fingerprint Authentication standby mode [8]+[] button: Clear Fingerprint Authentication standby mode
- Welcome function on: The mode will automatically activate the authorization standby mode when a approaches the door lock. - Welcome function off: The mode will authorize a when the enters the on the number pad or connects a card to the number pad. - One-minute alarm function on/ off: When someone remains in front of the door lock for more than a minute, this mode will sound the tamper prevention alarm.
Caution
- Automatic: The door is automatically locked 1 seconds after being closed. - Manual: The door does not lock automatically, and [CLOSE] button must be pressed from the inside, touch [Number Pad] to close the door.
Intrusion Detection Function This function generates the alarm sound when an attempt is made to forcefully open the door from the inside or the outside. (This is a basic function of the lock, and cannot be separately set or released.) If the door is forcefully opened while locked, the door opening sensor detects it and generates the alarm sound.
Battery Replacement Alarm Generation
Replacing the Battery Replace all 8 batteries within a 1 week of the first alarm sound. - The unit will stop operating suddenly if the batteries are not replaced.
DING DONG DENG [7] Button : Multi-leveled Security Code Entry Mode [9] Button : Common Mode
Briefly press the [] button on the inner body.
Press the [] button after pressing the [7] or [9] button, and the security mode will be set.
Door Lock Time Setup Function This function sets the time interval between the moment the door open/closed sensor recognizes the door as closed and the moment deadbolt locks the door. In an environment that the door closes slowly and the deadbolt jams before the door is fully closed, the situation can be fixed by adjusting the door lock time. DING DONG
Default: 1 second [51] : 1 second
Press [51] ~ [59] button, and then press [] button.
10
Press the [] button.
Outside
Apply the ed card or key tag to the card reader, or enter the and then press the [] button.
Built-in Fire Detection Function This function generates the alarm sound when fire is detected so that the residence can quickly respond. The built-in fire detection function is a basic function of the lock, and cannot be released by the . Fire detection function is operational at about 70 °C ± 10 °C; this can vary depending on the installation environment.
Product Specifications Item Voltage
Using the Emergency Battery
Operation Method
Electronic Control Method (, Fingerprint, Bluetooth, Card, Key Tag)
Product Dimensions
Purchase an emergency battery (9V) at the nearest store. - As the alkaline batteries offer longer life, they are recommended over the manganese batteries or rechargeable ones.
11
AA Alkaline 1.5 Batteries (LR6) 4EA or 8EA (6V) 9V Battery (6LF22) (Separately sold)
Weight
Opening the Door Using an Emergency Battery
Specifications
Emergency Power Source
If the batteries are not replaced after their replacement time comes, they will be completely discharged and the lock will not operate.
While connecting a 9V battery to the point, it is available to use fingerprint, card and .
[59] : 9 second
Open the battery cover of the inner body and briefly press the [] button.
● Depending on battery manufacturer, date of manufacture and the environment, the duration of use may vary. (In the case of average use, given as 10 times a day, 8 AA alkaline 1.5Vbatteries can last for 10 months.) ● If the poles of the batteries are not placed properly, the lock will not operate normally. ● Liquid leaks from batteries can damage the product. Check the batteries regularly (every 6 months). ● After the battery replacement alarm has sounded, /card information cannot be ed, changed, deleted, initialized or configured until the batteries are replaced. ~
Warning
You can set the security mode suitable for your use when you open the door using a .
Inside
When fire occurs, the temperature sensor detects it and flashes the [Close] button while generating the alarm sound. The door is automatically opened after the alarm sound has stopped. (The lock resumes normal operation if the inside temperature returns to a normal level.) The built-in fire detection function is activated when the temperature rises around 60°C, which may differ depending on the installation environment.
If the melody of “Blues for Elise” sounds when opening the door with the or a card (key tag), it is time to replace the batteries. (The low battery indicator is lighted when the melody sounds.)
Multi-leveled Security Code Entry Mode
This alarm will sound if an attempt is made to open the door with an invalid card, or if a wrong is entered five times in a row. The alarm sound is generated, and the lock is deactivated for 3 minutes. While the door is in this inactive mode, a single “DING” sound is generated every 10 seconds and seven consecutive “DINGS” will sound after 3 minutes. Following this, the lock is released from inactive mode.)
Releasing the Alarm
Replacing the Batteries
●The factory defaults are set with the welcome function on and the alarm function off. ● The working distance of the infrared sensor can differ depending on light conditions and other environments. When the front door is exposed to sun light or constant bright lights it is advised to limit the usage of the sensor as it might sound the alarm.
DING DONG
Set the [Automatic/Manual Locking] toggle switch of the Inner Body to the ‘A’/‘M’ position.
4.1 kg (including both inner and outer bodies) Outer Body (including the handle)
87.5mm(W) X 391.8mm(H) X 64.5mm(D)
Inner Body (including the handle)
88.5mm (W) X 357.6mm(H) X 69.3mm(D)
● T he contents of this guide are subject to change without prior notice to the in order to enhance performance of the product.
12
SHP-DP920 Samsung SDS Door Lock and Reference Guide
Ver1.0.0
Product Specifications Item
Spec.
Exterior Unit
87.5mm(W)×391.8mm(H)×64.5mm(D)
Interior Unit
88.5mm(W)×357.6mm(H)×69.3mm(D)
Size Voltage Emergency Power Source Battery Life Card Standard
Exterior Parts
4 AA Alkaline 1.5V Batteries (LR6) (6V) 9V Battery(6LF22)
(Separately sold)
10 Months (based on an average of 6 uses per day) ISO14443A (Mifare® )
Interior Parts
Mortise
The Samsung SDS Z-Wave Door Lock is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enable Z-Wave Plus products. The Samsung SDS Z-Wave Door Lock must be used in conjunction with a Security Enabled Z-Wave Controller in other to fully utilize all implemented functions. The Samsung SDS Z-Wave Door Lock can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Z-Wave Specifications
Device Type
:
Door Lock – Keypad (SPECIFIC_TYPE_SECURE_KEYPAD_DOOR_LOCK)
Role Type
:
LSS (Listening Sleeping Slave)
Command Class /Control
Mandatory CC :
Z-Wave plus info (MUST be place first in NIF) – (V2)
Manufacturer Specific (V2)
Security (V1)
Device Reset Locally (V1)
Battery (V1)
Power Level (V1)
Version (V2)
Door Lock (V2)
Code (V1)
Association (V2)
Association Group Information (V1)
Recommended CC
Notification (V4)
Configuration (V1)
Firmware update meta data (V2)
Schedule Entry Lock (V3)
Time Parameters (V1)
Time (V2)
Z-Wave plus info (V2) -
Z-Wave Plus Version : 02
-
Role Type : LSS (Listening Sleeping Slave)
-
Node Type : Z-Wave Plus Node
Manufacturer Specific (V2) -
Device ID Type : 01(Serial Number)
-
Device ID Data Format : 01 (Binary)
-
Device ID Data Length Indicator : 16
-
Device ID : XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX
Version (V2) -
Z-Wave Protocol Library Type : 03
-
Z-Wave Protocol Version : 04
-
Z-Wave Protocol Sub Version : 05
-
Firmware 0 Version : 01
-
Firmware 0 Sub Version : 03
-
Hardware Version : 01
Door Lock (V2) -
Unsecure(0x00), Secure(0xFF) Note : When using ‘Operation_Set’ command, lock will execute ‘Unsecure(0x00)’ then perform ‘Auto Re-lock’ if door is not open. When using ‘Operation_Get’ command, lock ‘Operation_Set’ command. (take about 2 seconds)
can
response
after
executing
Code (V1) -
Lock will accept maximum 130 pin codes that are 4-10 digits in length. ① ed s : 130 ② Type : Number, Card (Key Tag), Fingerprint, Bluetooth ⋅ Card (Key Tag), Fingerprint, Bluetooth : Cannot be ed through Z-Wave ③ ID Range ⋅ Number : 1 ~ 130
⋅ Card (Key Tag) : 1 ~ 20 ⋅ Bluetooth : 21 ~ 30 ⋅ Fingerprint : 31 ~ 130
Association (V2) & Association Group Information (V1) -
Lifeline between controller and SHP-DP920
-
ed command classes : Battery report, Notification report, and Device Reset Locally notification
Maximum ed node is 1EA
Notification (V4) Notification Type
Event
Access Control
Manual Lock Operation (0x01)
(0x06)
Manual Unlock Operation (0x02)
Event Parameter
RF Lock Operation (0x03) RF Unlock Operation (0x04) Keypad Unlock Operation (0x06) RF Not Fully Locked Operation (0x08) Auto Lock Loced Operation (0x09) Auto Lock Not Fully Operation (0x0A) Lock Jammed (0x0B) All codes deleted (0x0C) Single code deleted (0x0D) New code added (0x0E) New code not added due to duplicate code (0x0F) New Program code Entered - Unique code for lock configuration (0x12) Home Security (0x07)
Intrusion, Unkown Location (0x02) Tampering, Invalid Code (0x04)
ID
Motion Detection, Unknown Location (0x08) Emergency
Police (0x01)
(0x0A)
Fire Service (0x02)
Configuration (V1)
Name
Parameter Number
Size
Value
Description
Security Function
0x01
1byte
0x00
Disable (Default)
0x01
Enable
0x02
System Disable
0x03
System Enable
0x04
Request for Enable
0x05
Fail
0x00
Disable (Default)
0x01
Enable
Privacy Mode
0x02
1byte
1)
1)
1)
1)
ed ID
0x03
1byte
1 ~130
The number of ed codes.
Platform
0x0A
1byte
0x00
Common (Default)
0x01
Samsung SDS
1)
2)
3)
This value can be used when the device is connected with platform of Samsung SDS. This function is not related to Z-Wave CC. - 0x02 : Command for disable which is set by platform of Samsung SDS. After setting, if you try to get value of Security Function , '0x00' will be reported. - 0x03 : Command for enable which is set by platform of Samsung SDS. After setting, if you try to get value of Security Function, '0x01' will be reported. - 0x04 : 'Request for Enable' command which is reported by Doorlock. This cannot be set. (8th function in manual) - 0x05 : If the request for 'Request for Enable' command is failed in platform, this will be set by platform of Samsung SDS.
Value of Security Function is not changed by this command. 2)
This parameter is ed to ‘Configuration Get Command’ only.
3)
This value set by platform after device connected with platform of Samsung SDS.
Firmware update meta data (V2) -
Manufacturer ID : 0x022E (Samsung SDS)
Schedule Entry Lock (V3) -
ed the Number of Slots Week Day : 0
-
ed the Number of Slots Year Day : 0
-
ed the Number of Slots Daily Repeating : 130
Glossary Devices and nodes are all to describe an individual Z-Wave device. These
Device or Node
Unsecure Unsecured
are all interchangeable when setting up your Z-Wave network /
Unlock / Unlocked
Secure / Secured
Lock / Locked
Inclusion
Add a Z-Wave device to the network
Exclusion
Delete a Z-Wave device from the network A collection of Z-Wave devices is controlled by primary and secondary controllers
Z-Wave Network
operating on the same system. A Z-Wave network has its own unique ID code so that controllers not in the network cannot control the system. Association is used to organize nodes in different groups allowing the device to
Association
identify the nodes by a group identifier. The groups can also be copied to other devices.
Note : Pressing the [REG] button is only available while the door is open. (Deadbolt must be unsecured.)
Basic Functions
1. Factory Reset All ed Master/ data will be deleted, and Master PIN Code is set to ‘1234’. Also ZWave Door Lock is being removed from a network. ①
Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
②
Press the [*] button after pressing the [4560852580] button. (Success : Ding dong dang, Fail : Ding dong Ding dong)
※ Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
2. Changing the Master PIN Code You can enter only one Master PIN Code. If changing the Master PIN code, All PIN Codes are deleted. ①
Press the [REG] button. (Ding dong)
②
Enter the new Master PIN Code, and press the [*] button.(4~12digits) (Ding dong dang)
3. ing a Card You can up to 20 Card. (Supproted ISO14443 A Type) To multiple cards, lightly place another card to the card reader within 20 seconds after ing the previous card. Also you can add card later after completing registration. ①
Press the [REG] button. (Ding dong)
②
Place the card to be ed on the card reader of the exterior body.(Ding dong dang)
③
Place the card on the card reader for the addtional registration or press the [REG] button to quit.
4. ing a Fingerprint You can up to 100 fingerprints. ①
Press the [REG] button. (Ding dong)
②
When LED light on the Fingerprint Reading is on, touch the with the fingerprint to be ed. When a “ding” sound is heard and LED light goes off, then remove the finger. (Must do it 3 times)
③
To end the registration, please press the [REG] button on the inner body.
5. ing a Bluetooth ①
Press the [REG] button. (Ding dong)
②
Enter the [88] + [*]
③
Enter the + [*] (Ding dong deng → Ding ding)
④
Check a pairing number from Smart Door Lock App of smartphone.
(Ding dong)
(First, please install the Smart Door Lock app in the smart phone.) ⑤
Enter a Pairing number + [*] (Ding dong deng)
6. Inclusion / Exclusion into(from) Z-Wave Network 6.1 Inclusion into Z-Wave Network ①
Click [Add] icon in Z-Wave PC Conroller Program.
②
Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
③
Press the [*] button after pressing the [00] button. (Success : Ding dong dang, Fail : Ding dong Ding dong)
6.2 Exclusion from Z-Wave Network After exclusion from Z-Wave Netwokr, it will no longer be remotely-controlled via the controller. ①
Click [Remove] icon in Z-Wave PC Conroller Program.
②
Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
③
Press the [*] button after pressing the [00] button.
(Success : Ding dong dang, Fail : Ding dong Ding dong)
7. Opening the Door with a PIN Code ①
Touch the [Touchscreen].
②
Enter the PIN Code and press the [*] button.
③
The door opens whithin one second.
8. Opening the Door with a Card ①
Place the Card on the Card Reader.
②
The door opens whithin one second.
9. Opening the Door with a Fingerprint ①
Press the [Open Fingerprint Cover] button and the lid of the Fingerprint Reading opens.
②
Touch the Fingerprint Reading with the ed fingerprint after LED light turns on, the lid of the closes in approximately a second later.
③
Then push the door handle to open the door.
10. Opening the Door with a Bluetooth ①
Access the door lock from the outside or touch its number pad.
②
The number pad will light up.
③
Push message is sent to smartphone through Bluetooth.
④
Press the icon of push message (from smartphone)
⑤
Then push the door handle to open the door.
Addtional Function
11. Activation/Deactivation of the Bluetooth Mode After the Bluetooth mode is activated, accessing the door lock from the outside or touching its number pad can authenticate the ed Bluetooth smartphone to open the door. The Bluetooth mode is activated by default. ①
Open the battery cover, and press the [REG] button shortly..
②
Press the [11] or [00] button and the [*] button to activate or deactivate the Bluetooth mode. [11] button: Activate the Bluetooth mode. [00] button: Deactivate the Bluetooth mode.
12. Privacy Mode Function Press and hold the [CLOSE] button for more than three seconds. (Ding dong dang) As it is set from the inside, provides a secure lock for the convenience of the occupant(s). When the privacy mode function is activated, the door cannot be unlocked(unsecured) from the outside, so please be careful.
13. Setting the Security Function This is a function to prevent any intrusion while you are out. Should the door be opend from the inside while the intrusion prevention function is on, the emergency alert light will flash and the alarm will make “beep beep beep~” sound. ①
When the door is closed [
②
Press the [
] of the exterior body’s number pad will light up.
] button on the exterior body within 3 seconds while the door is locked.
(Ding dong dang)
14. Lockout Mode When more than 5 failed authentication attempts with uned PIN Code/Cards occur, the alarm sound is generated, and the lock is deactivated for 3 minutes.
15. Intrusion Detection Function When the Interior Unit is forcibly detached while the door is locked, it is detected by the door open/close sensor, the alarm sounds. The Intrution Detection function is a basic function and cannot be disabled.
16. Sound Setting The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unloced, can be set according to the ’s preference. Put the [Sound Control] switch on one of [0], [1] or [2]. [0] : Mute
[1] : Normal
[2] : Loud
17. Addtional Function Mode
Related Documents 3h463d
Shp-dp920 728 Manual 4mk3n
October 2019 150
Esprit 728 Express Y 728 + V 3.1 Manual Instalacion Esp 5e1t63
November 2019 79
103 728 1 Pb 41g4e
September 2022 0
Teamsters Local 728 @ Work 2u2e35
November 2019 52
Manual De Prog. Central Posonic 728 453r2
October 2019 61
Centrales Paradox 728 738 748 n624c
December 2019 53More Documents from "Gertrude Ramsbottom" 2j37e
Ambient Ws1001wifi 653e63
August 2021 0
Ambient Ws-2902 Manual 2bx1z
January 2022 0
Shp-dp920 728 Manual 4mk3n
October 2019 150
Knowing The Oriental 3j6v4n
November 2019 52
Choosing A Mixed Methods Design 442r3r
November 2022 0