Complete Presentation Of Zxsdr Bts Configuration (v4.00.210c) 37 1s4h4

ZXSDR Series Base Station Configuration

Contents • • • • • •

Configuration Process Background and Preparation OMCR Configuration OMCB Configuration LMT Configuration Data Synchronization

Configuration Process E1 transmission

FE transmission Start Creating managed element at SDR site. Configuring physical data at SDR site. Configuring radio resource at SDR site.

Start

Configure OMCR Data

Configure OMCB Data

configuring Ethernet, global port number, IP, SCTP, and OMCB

Configure LMT Transmission Parameter

Synchronize data to foreground

Configure OMCR Data

Configure OMCB Data

Synchronize data to foreground Perform data synchronization after link setup

End

remote link setup

End

Foreground-background link setup conditions ：  Transmission network is ok.  Configure relevant interface parameters for SDR site in OMCR.

Create the managed element at SDR site in OMCB. Configure the transmission parameters in LMT.

Configuration Process Configuration Process By Using LMT

Start

Configure OMCR Data

Create manage element in OMCB

Configure LMT Data

Online data at background Perform online data after link setup

End

Contents • • • • • •

Configuration Process Background and Preparation OMCR Configuration OMCB Configuration LMT Configuration Data Synchronization

SDR Operation and Maintenance Networking Networking While Using Ethernet Bearing at Abis

Networking While Using E1/T1 Bearing at Abis

In the above topology, there is no RPU portion. In fact, the portion of route processing in iBSC is performed by RPU.

Networking Instance

Items

Configuration Information

Mask

IP address of network interface for OMCB at iBSC

139.1.1.254

255.255.255.0

OMCB server IP configured by iBSC

139.1.1.200

255.255.255.0

IP Abis virtual address of iBSC

118.18.1.1

255.255.255.255

OMCB channel address

118.18.1.1

255.255.255.255

IP address of network interface for SDR site at iBSC

118.18.X.254*

255.255.255.0

*In the instance, X=2, indicating GSM site id is 2.

IP address configured by SDR site

118.18.X.100

255.255.255.0

Contents • • • • • •

Configuration Process Background and Preparation OMCR Configuration OMCB Configuration LMT Configuration Data Synchronization

Configuring BSC Function OMCB IP

IPABIS and OMCB channel IP

For E1 transmission, both addresses are same. For FE transmission, two addresses are different if using VLAN, and you shall set two virtual addresses. If you do not use VLAN, both addresses are same too.

Configuring Abis Interface Board (E1 Abis) 1 DTB board PCM information while iBSC connects SDR site by using IP OVER E1 mode, select Multi frame.

2

Create the EUIP board

Configuring Abis Interface Board (FE Abis) Configure IPBB interface board

*While using FE mode at Abis, it is not required to configure DTB board and EUIP board for the resource shelf at Abis , and you shall configure IPBB interface board for the resource shelf at Abis

Configuring OMCB Interface Board Configure IPBB interface board

The IPBBs for OMCB access and SDR access can use the different network ports on a board, but these two network ports shall be configured in different network segments.

Configuring IP Abis Interface (Virtual Address) 1

Create RPU board function type

2 Set the parameters for IP ABIS

Configuring Access Interface for OMCB 1

Create IPBB board function type

2 Set the parameters for IPBB

Configuring Access Interface for SDR (E1 1 Create EUIP Interface for E1 Access Abis)

3

2

Create IP Over E1 Configuration

Create PPP Configuration

Configuring Access Interface for SDR (FE Abis) 1 Create IPBB board function type 2 Set the parameters for IPBB

Configuring Logic SDR Site 1

Configure a Logic Site

2

Configure a Rack

You can only create B8200 while configuring SDR site.

Configuring Logic SDR Site 1

Configure a Cell

2 Configure TRX

Contents • • • • • •

Configuration Process Background and Preparation OMCR Configuration OMCB Configuration LMT Configuration Data Synchronization

Modifying Server Profiles Modify deploy-030womcb.properties with omc

Modify FTP Related Profile with omc the default port number is 21

Configuring Basic SDR Data Create SDR Managed Element

Keeping consistent with the GSM base station id

Create Base Station Config Set

Configuring Base Station Equipment Create base station equipment resource 1 Resource 2 Configure physical rack BBU management Keeping consistent with the GSM base station id

3 Configure physical rack RRU

Configuring Base Station Equipment Resource 5 Configure the rack topology 4 Configure the antenna

Configuring Transmission Resource (E1 1 Configure the E1/T1 cable 3 Configure PPP configuration Abis) For the SDR site connected to BSC by star link, select BSC; for the SDR site connected to parent SDR site by chain link, select BTS

2 Configure the HDLC

Configuring Transmission Resource (E1 Global port 4 6 SCTP Abis) IP Abis （ RPU ）

5

IP property

For E1 transmission, it is not required. After link setup between foreground and background, automatically set it.

7 OMCB connection the IP address of OMCB channel

Configuring Transmission Resource (FE 3 Configure the IP property Abis) 1 Configure the Ethernet Select IPbone for direct station and select BTS for cascading station

2 Configure the global port

Configuring Transmission Resource (FE Abis) 4 SCTP 5 OMCB connection

*While using FE at Abis, you need use LMT to configure transmission parameters (consistent with the configuration data on OMCB). After link setup between foreground and background, you can synchronize the OMCB configuration data with foreground.

Configuring Radio Resource 1 Create base station radio resource management

2 Configure the central frequency point

Configuring Radio Resource 3 Configure the sector parameters

5 Configure the GSM carrier

4 Configure the GSM RU parameters

Contents • • • • • •

Configuration Process Background and Preparation OMCR Configuration OMCB Configuration SDR LMT Introduction Data Synchronization

Overview Local LMT configuration is same as the configuration done by OMCB. On field, you also can use all data configured by LMT,create the SDR managed element for this site on OMCB, to set up a link between foreground and background, so the SDR site data is reversely constructed at background.

LMT Directory     

EOMS: The special software version of EOMS and EFMS can be loaded or activated at the site by using LoadTool. EOMS_EFMS: the copy version of operation, maintenance, and fault management. JRE: the installer of Java running environment. LMTSetup.exe: DMS and PMS installer file. ree.txt: the ree file for installer.

LMT Connects SDR

CC ETH1 If there are CC boards on slot 1 and 2, you shall view the MS indicator after powering on.

Slot No.1 (CC-1) IP: 192.X.1.16 Slot No.2 (CC-2) IP: 192.X.2.16

*X is the environment ID, used to differentiate the different SDR sites within a network. The default environment ID is 254.

The procedure of configuring the base Items Data Type Steps Configuration station 1

2

3

4

BS configuration

Configure ground resource

Configure transmission resource

Configure radio

Step 1.1

Configure basic parameters for the base station

Step 1.2

Configure B8200 board and R8860 rack and board

Step 1.3

Configure clock reference source

Step 2.1

Configure environment monitoring

Step 2.2

Configure TMA controller

Step 2.3

Configure serial port

Step 2.4

Configure topology

Step 2.5

Set dyr

Step 3.1

Configure FE parameters(using IP transmission at Abis)*

Step 3.2

Configure E1/T1 connection(using E1/T1 transmission at Abis)

Step 3.3

Configure HDLC path parameter(using E1/T1 transmissionat Abis)

Step 3.4

Configure PPP parameters (using E1/T1 transmission at Abis)*

Step 3.5

Configure global port parameters*

Step 3.6

Configure IP parameters*

Step 3.7

Configure SCTP parameters*

Step 3.8

Configure 0MCB parameters*

Step 4.1

Configure the RF central frequency

*Configure it on FE transmission for link setup between foreground and background.

Contents • • • • • •

Configuration Process Background and Preparation OMCR Configuration OMCB Configuration SDR LMT Introduction Data Synchronization

Data Synchronization After link setup at foreground and background, the small green icon in front of the site managed element becomes connected state

Online ing Data

If all configuration actions have been done by LMT at SDR site and the network transmission is proper, the link is set up between foreground and background. After link setup, you can the existing data at foreground into background.